Add vid/pid for the SMK branded third-party PS3 Bluetooth remote and enable
support in the hid-sony driver.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Replace stack buffers with kernel allocated buffers for sending
and receiving HID reports to prevent issues with DMA transfers
on certain hardware.
Output report buffers are allocated at initialization time to avoid
excessive calls to kmalloc and kfree.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=87991
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DualShock 4 touchpad has been measured to have a resolution of
44.86 dots/mm which equates to 1920x942.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Set the DualShock4 touchpad bits in the input_configured callback
so that they are registered properly for any input devices created
during hid_hw_start.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update the file header and correct an outdated comment block.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a few minor issues in the HID descriptor:
- A 6 bit entry had a logical maximum of 255 when the largest it can be is 63.
- A logical max value was incorrectly being set to -1 instead of 255.
- Set the min/max of the gyroscopes to -8192/8191 as that is the range of
values which represent the true controller orientation. Any values beyond
those extents are just noise.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bit 3 in byte 31 of the Sixaxis report indicates whether the battery is
charging or not charging as opposed to whether or not the cable is plugged in.
As a result, when connected via USB and fully charged, the power_supply status
is wrongly reported as 'Discharging' instead of 'Full'.
Use the battery level value to set the cable state so that the power status
is reported correctly as that seems to be the only reliable way to determine the
cable status on the Sixaxis.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously only the first element of the array was initialized to 1
leading to potential incorrect max brightness values for the LEDs
on the Dualshock 3 and buzzer controllers.
Use a designated initializer to initialize the whole array to the
correct value.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove an old redundant comment before sony_report_fixup(), it must have
been a leftover from the first version of the driver:
sony_report_fixup() now handles all the supported devices, not only the
Sony Vaio VGX.
The comment is also redundant as the same information provided by it is
also present in the body of the function.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reformat sixaxis_rdesc to reflect its HID structure, and comment each
field. This will make it easier to validate changes to the descriptor in
the future.
No functional changes are introduced, the descriptor is exactly the same
as before byte by byte.
The heavy lifting has been done with the help of hidrd-convert:
https://github.com/DIGImend/hidrd
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Simplify the logic of overriding the Sixaxis HID descriptor, this will
make it easier to amend the descriptor in future commits.
The current code does this:
if (original sixaxis via USB or BT)
fixup only a part of the descriptor
else if (sixaxis compatible controller)
override the _whole_ descriptor
but the end result is exactly the same, except for the trailing zero in
the case of original BT controllers.
So let's just regularize the process, and always override the HID
descriptor.
Always overriding the descriptor changes the current semantic a little
bit, before this change the BT descriptor still had the trailing zero
byte, while now it is exactly the same as the descriptor of the
controller via USB, but that does not affect proper operation of the
device.
Note that overriding the whole descriptor for original devices is not
strictly necessary for now, but it simplifies the code and in the future
the report descriptor will be patched further and keys will be remapped,
so it's handy to have only one place to patch.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of checking for SIXAXIS_CONTROLLER_USB and SIXAXIS_CONTROLLER_BT
separately, a check on SIXAXIS_CONTROLLER can be used when setting
connect_mask.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without this patch the 3rd party INTEC (PS3) controller will blink all
leds when user turns them off, it appears to require an extra flag set.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for setting the blink rate of the LEDs. The Sixaxis allows control
over each individual LED, but the Dualshock 4 only has one global control for
controlling the hardware blink rate so individual colors will fall back to
software timers.
Setting the brightness cancels the blinking as per the LED class specifications.
The Sixaxis and Dualshock 4 controllers accept delays in decisecond increments
from 0 to 255 (2550 milliseconds).
The value at index 1 of the DualShock 4 USB output report must be 0xFF or the
light bar won't blink.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add an IDA id allocator to assign unique, sequential device ids to Sixaxis and
DualShock 4 controllers.
Use the device ID to initialize the Sixaxis and DualShock 4 controller LEDs to
default values. The number or color of the controller is set relative to other
connected Sony controllers.
Set the LED class brightness values to the initial values and add the new led to
the array before calling led_classdev_register so that the correct brightness
value shows up in the LED sysfs entry.
Use explicit module init and exit functions since the IDA allocator must be
manually destroyed when the module is unloaded.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the controller Bluetooth MAC address as the unique identifier in the
battery name string instead of the atomic integer that was used before.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Convert all of the local initialization and shutdown functions to take a
parameter type of struct sony_sc* instead of using a mix of struct sony_sc* and
struct hid_device*.
Allows for the removal of some calls to hid_get_drvdata().
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use a struct for the Sixaxis output report that uses named members to set the
report fields.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use inliners to make sure that the work queue initialization flag is always
checked and set correctly when initializing or cancelling the work queue.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix unfortunate mismerge between the fixes and sony branch causing
code duplication and unterminated basic block.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Sixaxis and DualShock 4 want HID output reports sent on the control
endpoint when connected via Bluetooth. Set the
HID_QUIRK_NO_OUTPUT_REPORTS_ON_INTR_EP flag for these devices so hidraw write()
works properly.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Byte 31 of the Sixaxis report can change depending on whether or not the
controller is rumbling. Using bit 3 is the only reliable way to detect the
state of the cable regardless of rumble activity.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_out_raw_report is going to be obsoleted as it is not part of the
unified HID low level transport documentation
(Documentation/hid/hid-transport.txt)
To do so, we need to introduce two new quirks:
* HID_QUIRK_NO_OUTPUT_REPORTS_ON_INTR_EP: this quirks prevents the
transport driver to use the interrupt channel to send output report
(and thus force to use HID_REQ_SET_REPORT command)
* HID_QUIRK_SKIP_OUTPUT_REPORT_ID: this one forces usbhid to not
include the report ID in the buffer it sends to the device through
HID_REQ_SET_REPORT in case of an output report
This also fixes a regression introduced in commit 3a75b24949
(HID: hidraw: replace hid_output_raw_report() calls by appropriates ones).
The hidraw API was not able to communicate with the PS3 SixAxis
controllers in USB mode.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a Sixaxis or Dualshock 4 controller is connected via USB while already
connected via Bluetooth it will cause duplicate devices to be added to the
input device list.
To prevent this a global list of controllers and their MAC addresses is
maintained and new controllers are checked against this list. If a duplicate
is found, the probe function will exit with -EEXIST.
On USB the MAC is retrieved via a feature report. On Bluetooth neither
controller reports the MAC address in a feature report so the MAC is parsed from
the uniq string. As uniq cannot be guaranteed to be a MAC address in every case
(uHID or the behavior of HIDP changing) a parsing failure will not prevent the
connection.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make sure that an out-of-bounds read doesn't occur in the Sixaxis battery level
lookup table in the event that the controller sends an invalid battery status
value in the report.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only initialize force feedback for devices that actually support it (Sixaxis and
Dualshock 4) to prevent calls to schedule_work() with an uninitialized work
queue.
Move the cancel_work_sync() call out of sony_destroy_ff() since the state worker
is used for the LEDs even when force-feedback is disabled.
Remove the sony_destroy_ff() function since it is no longer used.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Convert multi-line comments to comply with the kernel coding style.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't initialize force-feedback for devices that don't support it to avoid calls
to schedule_work() with an uninitialized work_struct.
Move the cancel_work_sync() call out of sony_destroy_ff() since the state worker
is used for the LEDs even when force-feedback is disabled.
Remove sony_destroy_ff() to avoid a compiler warning since it is no longer used.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a SIXAXIS_CONTROLLER macro to simplify conditionals where the
connection type is irrelevant.
Enable the LED and force feedback controls for Sixaxis controllers connected via
Bluetooth.
Send Sixaxis Bluetooth output reports on the control channel.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The battery_charging and cable_state flags were backwards on the Sixaxis.
The low bit of report byte 30 is 0 when charging and 1 when not.
Bit 5 of byte 31 is 0 when a USB cable is connected and 1 when not.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ret = hid_output_raw_report(A, B, C, HID_FEATURE_REPORT);
is equivalent to
ret = hid_hw_raw_request(A, B[0], B, C, HID_FEATURE_REPORT, HID_REQ_SET_REPORT);
whatever the transport layer is.
So use the new API where available
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the conditionals to enable rumble, battery reporting, LED and touchpad
support for the Dualshock 4 in Bluetooth mode.
Add dualshock4_set_operational_bt to initialize the controller to the proper
operational state.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Set the initial battery level to 100% to avoid false low battery warnings if
the battery state is polled before a report with the actual battery level is
received.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Dualshock 4 battery and touchpad parsing for Bluetooth reports.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add formating for the Dualshock 4 output report data in Bluetooth mode.
In Bluetooth mode the Dualshock 4 wants output reports sent on the control
channel.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default, the Dualshock 4 sends controller data via report 1. Once a valid
output report 0x11 is received or a feature report of type 0x02 is requested the
controller changes from sending data in report 1 to sending data in report 17,
which is unmapped in the default descriptor. The mappings have to be moved to
report 17 to let the HID driver properly process the incoming reports.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch to the low-level transport driver functions.
sony_set_output_report is removed since it is no longer used.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a helper to access hdev->hid_output_raw_report().
To convert the drivers, use the following snippets:
for i in drivers/hid/*.c
do
sed -i.bak "s/[^ \t]*->hid_output_raw_report(/hid_output_raw_report(/g" $i
done
Then manually fix for checkpatch.pl
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
dev->hid_get_raw_report(X) and hid_hw_raw_request(X, HID_REQ_GET_REPORT)
are strictly equivalent. Switch the hid subsystem to the hid_hw notation
and remove the field .hid_get_raw_report in struct hid_device.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Dualshock4 controller contains a RGB LED, which is enabled via
the '/sys/class/leds' interface. At present the driver only returns
whether each of the RGB LEDs is lit (ie not off), but no indication
of it's brightness.
This patch fixes the reading of the current brightnes so that it
returns the value (rather than just off=0, on=LED_FULL).
Tested on the DS4 and SixAxis (for compatibility).
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add output events for the multi-touch pad on the Dualshock 4.
The touchpad has a resolution of 1920x940 and is capable of 2 simultaneous
touches. A 'Type B' stateful slot protocol is implemented as defined in
Documentation/input/multi-touch-protocol.txt
Applications can use the touchpad data by processing the ABS_MT_SLOT,
ABS_MT_TRACKING_ID, ABS_MT_POSITION_X and ABS_MT_POSITION_Y events.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add battery status reporting for the Sixaxis and Dualshock 4 controllers.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the naming scheme 'devicename:colour' for the Dualshock 4
LED lightbar controls as specified in Documentation/leds/leds-class.txt
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Frank Praznik
Antonio Ospite
Simon Wood
Jiri Kosina
Benjamin Tissoires