This patch adds support for LZO compression when storing the register
cache. The initial register defaults cache is marked as __devinitconst
and the only change required for a driver to use LZO compression is
to set the compress_type member in codec->driver to SND_SOC_LZO_COMPRESSION.
For a typical device whose register map would normally occupy 25kB or 50kB
by using the LZO compression technique, one can get down to ~5-7kB. There
might be a performance penalty associated with each individual read/write
due to decompressing/compressing the underlying cache, however that should not
be noticeable. These memory benefits depend on whether the target architecture
can get rid of the memory occupied by the original register defaults cache
which is marked as __devinitconst. Nevertheless there will be some memory
gain even if the target architecture can't get rid of the original register
map, this should be around ~30-32kB instead of 50kB.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch introduces the new caching API and migrates the
old caching interface into the new one. The flat register caching
technique does not use compression at all and it is equivalent to
the old caching technique. One can still access codec->reg_cache
directly but this is not advised as that will not be portable
across different caching strategies.
None of the existing drivers need to be changed to adapt to this
caching technique. There should be no noticeable overhead associated
with using the new caching API.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Based on discussion the dapm_pop_time in debugsfs should be per card rather
than per device. Single pop time value for entire card is cleaner when the
DAPM sequencing is extended to cross-device paths.
debugfs/asoc/{card->name}/{codec dir}/dapm_pop_time
->
debugfs/asoc/{card->name}/dapm_pop_time
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There will be need to have sound card specific debugfs entries. This patch
introduces a new debugfs/asoc/{card->name}/ directory but does not add yet
any entries there.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.
This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.
This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.
Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Facilitating adding trace type stuff. For a first pass add some dev_dbg()
statements into them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
This patch removes the old CONFIG_SYSFS_DEPRECATED_V2 config option,
but it keeps the logic around to handle block devices in the old manner
as some people like to run new kernel versions on old (pre 2007/2008)
distros.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is adding support for alc562[123] codecs. It's based
on the source code available in HP source code and other places.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit f6765502f8 and adds
the missing include file.
Signed-off-by: Peter Hsiang <Peter.Hsiang@maxim-ic.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CCR is defined in emu10k1, but SuperH is defined too.
If user use this driver with SuperH, it becomes a double definition.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we compile the ASoC code with PM disabled, we hit stuff like:
sound/soc/soc-dapm.c: In function 'snd_soc_dapm_suspend_check':
sound/soc/soc-dapm.c:440: warning: unused variable 'codec'
So tweak the stub macro to avoid these issues.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With generic AC97 ASoC glue driver (codec/ac97.c), we get following warning when
the device is registered (slightly stripped the backtrace):
kobject (c5a863e8): tried to init an initialized object, something is seriously
wrong.
[<c00254fc>] (unwind_backtrace+0x0/0xec)
[<c014fad0>] (kobject_init+0x38/0x70)
[<c0171e94>] (device_initialize+0x20/0x70)
[<c017267c>] (device_register+0xc/0x18)
[<bf20db70>] (snd_soc_instantiate_cards+0x924/0xacc [snd_soc_core])
[<bf20e0d0>] (snd_soc_register_platform+0x16c/0x198 [snd_soc_core])
[<c0175304>] (platform_drv_probe+0x18/0x1c)
[<c0174454>] (driver_probe_device+0xb0/0x16c)
[<c017456c>] (__driver_attach+0x5c/0x7c)
[<c0173cec>] (bus_for_each_dev+0x48/0x78)
[<c0173600>] (bus_add_driver+0x98/0x214)
[<c0174834>] (driver_register+0xa4/0x130)
[<c001f410>] (do_one_initcall+0xd0/0x1a4)
[<c0062ddc>] (sys_init_module+0x12b0/0x1454)
This happens because the generic AC97 glue driver creates its codec->ac97 via
calling snd_ac97_mixer(). snd_ac97_mixer() provides own version of
snd_device.register which handles the device registration when
snd_card_register() is called.
To avoid registering the AC97 device twice, we add a new flag to the
snd_soc_codec: ac97_created which tells whether the AC97 device was created by
SoC subsystem.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than block the workqueue by sleeping to do the debounce use delayed
work to implement the debounce time. This should also means that we extend
the debounce time on each new bounce, potentially allowing shorter debounce
times for clean insertions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8962 features five GPIOs, add support for controlling their output
state via gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add the widget for MICBIAS power control and allow configuration of the
microphone bias setup via the platform data for the WM8962. When
microphone status signals are brought out to GPIO this should be
sufficient to enable microphone detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide an initial hookup for interrupts on the WM8962. Currently we simply
report error status via log messages if an IRQ is provided for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some devices have more flexible microphone detection and can detect
a wider range of buttons.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Swapping the bias level enumeration is only meant to help debugging. It is
easier if number 0 means bias off and bigger number means bigger bias level.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The current code in pcm_lib.c do all checks using only the position
in the ring buffer. Unfortunately, where the interrupts gets delayed or
merged into one, we need another timing source to check when the
buffer size boundary overlaps to avoid the wrong updating of the
ring buffer pointers.
This code uses jiffies to check the right time window without any
performance impact.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With some hardware combinations, the PCM interrupts are acknowledged
before the period boundary from the emu10k1 chip. The midlevel PCM code
gets confused and the playback stream is interrupted.
It seems that the interrupt processing shift by 2 samples is enough
to fix this issue. This default value does not harm other,
non-affected hardware.
More information: Kernel bugzilla bug#16300
[A copmile warning fixed by tiwai]
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
unifdef-y and header-y has same semantic.
So there is no need to have both.
Drop the unifdef-y variant and sort all lines again
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
The WM8962 is a low power, high performance stereo CODEC designed for
portable digital audio applications.
This initial driver release supports the key audio paths of the WM8962.
Extended functionality, such as microphone detection, digital microphones
and the advanced DSP signal enhancements provided by the device are not
yet supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Platform parameter to enable automatic FIFO configuration when
the codec is in Mode1 or Mode7 FIFO mode.
When this mode is selected, the controls for changing
nSample (in Mode1), and UTHR (in Mode7) are not added.
The driver configures the FIFO configuration based on
the stream's period size in a way, that every burst will
read period size of data from the host.
In Mode7 we need to use a formula, which gives close enough
aproximation for the burst length from the host point
of view.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Replace the hardwired latency definition with platform data
parameter, and simplify the nSample parameter calculation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
All current users of pm_qos_add_request() have the ability to supply
the memory required by the pm_qos routines, so make them do this and
eliminate the kmalloc() with pm_qos_add_request(). This has the
double benefit of making the call never fail and allowing it to be
called from atomic context.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Specified ID is necessary, when some codecs are used with FSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add hw_params to snd_soc_dai_ops,
because board specific set_rate is needed
when FSI was used as master mode.
This patch remove fsi_clk_ctrl from fsi_dai_startup,
because clock should be disabled before set_rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no necessity that each bit in this area has the meaning.
This patch modify it to sequence number
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When using poll() to wait for the next period -- or avail_min samples --
one gets a consistent delay for each system call that is usually just a
little short of the selected period time. However, When using
snd_pcm_read/write(), one gets a jittery delay that alternates between
less than a millisecond and approximately two period times. This is
caused by snd_pcm_lib_{read,write}1() transferring any available samples
to the user's buffer and adjusting the application pointer prior to
sleeping to the end of the current period. When the next period
interrupt occurs, there is then less than avail_min samples remaining to
be transferred in the period, so we end up sleeping until a second
period occurs.
This is solved by using runtime->twake as the number of samples needed
for a wakeup in addition to selecting the proper wait queue to wake in
snd_pcm_update_state(). This requires twake to be non-zero when used
by snd_pcm_lib_{read,write}1() even if avail_min is zero.
Signed-off-by: Dave Dillow <dave@thedillows.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This change wipes out a hardcoded macro, which enables codec bias
level control. Now is_powered_on_standby value shall be used instead.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some systems codecs need to configure some registers before and after
powering down some of their part. As a convenience add a macro for that.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This defines the 24bps and 40bps (8khz sample rate) G.723 codec
formats. They are going to be used once I submit the driver for
an mpeg4/g723 compression card.
I've updated the signed value to -1 as per Takashi's comments
since these are non-linear formats.
Signed-off-by: Ben Collins <bcollins@bluecherry.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
This patch is adding a new control which has the following capabilities:
- tlv
- variable data size (for instance, 7 ou 8 bit)
- double mixer
- data range centered around 0
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: Liam Girdwood <lrg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the register for the volume needs invert, than the inversion
need to be done from the chip maximum, and not from the platform
dependent limit.
Introduce soc_mixer_control.platform_max value, which initially
equals to chip maximum.
The snd_soc_limit_volume function only modify the platform_max,
all volsw_info call returns this as well.
The .max value holds the chip default (maximum), and it is used
for the inversion, if it is needed.
Additional check in the volsw_info call has been added to check
the validity of the platform_max in case, when custom macros
used by codec drivers are not initializing it correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
As well as allowing DAPM pins to be marked as ignoring suspend allow DAI
links to be similarly marked. This is primarily intended for digital
links between CODECs and non-CPU devices such as basebands in mobile
phones and will suppress all suspend calls for the DAI link. It is
likely that this will need to be revisited if used with devices which
are part of the SoC CPU.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices can usefully run audio while the Linux system is suspended.
One of the most common examples is smartphone systems, which are normally
designed to allow audio to be run between the baseband and the CODEC
without passing through the CPU and so can suspend the CPU when on a
voice call for additional power savings.
Support such systems by providing an API snd_soc_dapm_ignore_suspend().
This can be used to mark DAPM endpoints as not being sensitive to
system suspend. When the system is being suspended paths between
endpoints which are marked as ignoring suspend will be kept active.
Both source and sink must be marked, and there must already be an
active path between the two endpoints prior to suspend.
When paths are active over suspend the bias management will hold the
device bias in the ON state. This is used to avoid suspending the
CODEC while it is still in use.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We now manage suspend within the main power analysis rather than by
flipping the state of widgets.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ESS ES968 chip is nothing more then a PnP companion
for a non-PnP audio chip. It was paired with non-PnP ESS' chips:
ES688 and ES1688. The ESS' audio chips are handled by the es1688
driver in native mode. The PnP cards are handled by the ES968
driver in SB compatible mode.
Move the ES968 chip handling to the es1688 driver so the driver
can handle both PnP and non-PnP cards. The es968 is removed.
Also, a new PnP id is added for the card I acquired (the change
was tested on this card).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allocate the snd_es1688 during the snd_card allocation.
This allows to remove the card pointer from the snd_es1688 structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 6f3991152f.
Since core has now support for limiting the volume on controls this
patch is not needed. Furthermore, this patch actually prevents the core
to set new volume on the TPA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for the core to limit the maximum volume on an
existing control.
The function will modify the soc_mixer_control.max value
of the given control.
The new value must be lower than the original one (chip maximum)
If there is a need for limiting a gain on a given control,
than machine drivers can do the following in their
snd_soc_dai_link.init function:
snd_soc_limit_volume(codec, "TPA6140A2 Headphone Playback Volume", 21);
This will modify the original 31 (chip maximum) to 21, so user
space will not be able to set the gain higher than this.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for platform dependent gain limiting on the
tpa6130a2 (and tpa6140a2) Headset amplifier.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Handle the reset GPIO within the codec driver in order to follow
the startup protocol for the tlv320aic3x codecs.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM9090 is a high performance low power audio subsystem, including
headphone and class D speaker drivers.
Note that this driver is a standalone CODEC driver and so is only
immediately suitable for use with the WM9090 as a standalone sound card
taking line inputs, or with a DAC with no software control. The pending
ASoC multi-CODEC support will expand the range of systems that can use
the driver, or system-specific adaptations can be made.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds support for Philips UDA1345 CODEC. The CODEC has only
volume control, de-emphasis, mute, DC filtering and power control features.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the features of the multi CODEC work is that it embeds a struct
device in the CODEC to provide diagnostics via a sysfs class rather than
via the device tree, at which point it's much better to use the struct
device private data rather than having two places to store it. Provide
an accessor function to allow this change to be made more easily, and
update all the CODEC drivers are updated.
To ensure use of the accessor the private data structure member is
renamed, meaning that if code developed with older an older core that
still uses private_data is merged it will fail to build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
[Note that this is a backported version for 2.6.34.
Upstream commit is fd23b7dee]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We actually pass an array of 7 chars not 5.
This silences a smatch warning.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some systems provide both mechanical and electrical detection of jack
status changes. On such systems power savings can be achieved by only
enabling the electrical detection methods when physical insertion has
been detected.
Begin supporting such systems by providing a notifier for jack status
changes which can be used to trigger any reconfiguration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices provide support for detection of a small number of
buttons on their jacks. One common implementation provides a single
button, implemented by shorting the microphone to ground and detected
along with microphone presence detection by detecting varying current
draws on the microphone bias signal.
Provide support for up to three buttons via the jack interface. These
default to reporting BTN_n but an API is provided to allow these to
be remapped to other keys by the machine driver where it knows what
the keys are. More keys can be added with ease if required.
This is only intended to support simple accessory button designs. If
the interface is limiting then either creating a child device for the
accessory or accessing the input device in the jack directly is
recommended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8904 allows microphone detection signals to be brought out as
alternate functions of the GPIO signals which can be detected using
interrupt inputs on the CPU. Allow this to be configured using
platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide platform data allowing the configuration of the GPIO pins
on the WM8904 to be selected, allowing alternate functions to be
enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Support use of the WM8903 IRQ for reporting of microphone presence
and short detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently used to detect completion of the write sequencer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide support for WM8903 microphone presence and short detection
using the GPIOs to route out a logic signal suitable for handling
using snd_soc_jack_add_gpios() on the processor GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow users to pass in a default configuration for the GPIOs of
the WM8903 as platform data. This allows configuration of the pin
muxing of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow pins to be forced on regardless of their power state. This is
intended for use with microphone bias supplies which need to be
enabled in order to support microphone detection - in systems without
appropriate hardware leaving the microphone unbiased when not in use
saves power.
The force done at power check time in order to avoid disrupting other
power detection logic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Platform data option for the codec to keep the BCLK clock
continuously running in FIFO modes (codec master).
OMAP3 McBSP when in slave mode needs continuous BCLK running
on the serial bus in order to operate correctly.
Since in FIFO mode the DAC33 can also shut down the BCLK clock
and enable it only when it is needed, let the platforms decide
if the CPU side needs the BCLK running or not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The flag is no longer used in the code so it just wastes a bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8960 headphone outputs can be run in capless mode with OUT3
used to drive a pseudo ground for the headphone drivers. In this
mode the mono mixer is not used, the mixer should be turned on
in concert with the headphone output drivers and the device bias
levels are managed differently.
Also tweak the existing bias management to remove the use of active
discharge while we're at it since that's often audible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Avoids machine files having to peer into sound/soc which is a bit
rude and icky.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The delay callback can be used by the core to query the delay
on the dai caused by FIFO or delay in the platform side.
In case if both CPU and CODEC dai has FIFO the delay reported
by each will be added to form the full delay on the chain.
If none of the dai has FIFO, than the delay will be kept as
zero.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we are to have a snd_soc_dai i.e, cpu_dai and codec_dai, shared among two
or more dai_links we need to log the number of active users of the dai.
For that, we change semantics of the snd_soc_dai.active flag from indicator
to reference counter.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order for having snd_soc_dais shared among two or more dai_links,
remove the relatively global runtime field from the struct snd_soc_dai
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Passing pointer to relevant dai_link provides easier reach to the
ASoC tree in suspend/resume of snd_soc_platform. It also provides
direct access to the dai at the other end of the dai_link.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make the pmdown_time a per-card setting rather than a global one,
initialised before the card initialisation runs. This allows cards
to override the default setting if it makes sense to do so (for
example, due to an unavoidable pop).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM2000 is a low power, high quality handset receiver speaker
driver with Wolfson myZone™ Ambient Noise Cancellation (ANC). It
provides enhanced voice communication quality in a noisy environment
if the handset acoustics are designed appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a bit to the CODEC structure indicating if a cache sync is required.
By default this will be set if a cache only write is done to a soc-cache
register cache. This allows us to avoid syncing the cache back after
using cache only writes if there were no changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently the soc-cache code will always write to the device, meaning
that we need the device to be powered and active at pretty much all
times the system is active. Allowing cache only writes lays some
groundwork for future enhancements to allow devices to be put into a
full off state when the audio subsystem is idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Clemens Ladisch noted for hw_ptr_removal in "cleanup & merge hw_ptr
update functions" commit:
"It is possible for the status/delay ioctls to be called when the sound
card's pointer register alreay shows a position at the beginning of the
new period, but immediately before the interrupt is actually executed.
(This happens regularly on a SMP machine with mplayer.) When that
happens, the code thinks that the position must be at least one period
ahead of the current position and drops an entire buffer of data."
Return back the hw_ptr_interrupt variable. The last interrupt pointer
is always computed from the latest hw_ptr instead of tracking it
separately (in this case all hw_ptr checks and modifications might
influence also hw_ptr_interrupt and it is difficult to keep it
consistent).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Several shortcuts for popular uses of some of SOC_ENUM_* and
SOC_VALUE_ENUM_* macros.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many macros from include/sound/soc-dapm.h take an array and a number of
elements in it as arguments, whereas most users use static arrays and use
"x, ARRAY_SIZE(x)" as arguments. This patch adds simplified versions of
those macros, calling ARRAY_SIZE() internally.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.oc.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC always maintains the bias of the CODEC while the system
is active. With older mobile CODECs this is required since the outputs
are referenced to a non-zero voltage and enabling or disabling this
voltage without audible pops or clicks in the output takes too long to
do when starting or stopping audio.
As a result of features such as ground referenced outputs and class D
speaker drivers current generation devices are able to power on and off
much more quickly without these system level issues so provide a new
flag idle_bias_off in snd_soc_codec which will cause the core to turn
off the CODEC bias. The distinction between STANDBY and OFF is still
maintained. This is partly for consistency but also allows for
potential future extensions such as per-machine overrides or deferring
the bias removal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This change fixes the "ALSA: pcm_lib - optimize wake_up() calls for PCM I/O"
commit. New sleeping queue is introduced to separate user space and kernel
space wake_ups. runtime->nowake is renamed to twake (transfer wake).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add possibility to configure the burst mode BCLK divider through platform
data structure.
The BCLK divider changes the actual speed of the serial bus in burst mode,
which is faster than the sampling frequency of the running stream.
In this way platforms can experiment with the optimal burst speed without
the need to modify the codec driver itself.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pgprot_noncached() can be set for vmalloc'ed buffers safely, and we'd
need non-cached behavior more or less, even for the intermediate ring-
buffers.
Now snd_pcm_lib_mmap_vmalloc() is added as the common PCM mmap callback
that is coupled with snd_pcm_lib_alloc_vmalloc_buffer() & co.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new function to look up a quirk entry with the given PCI SSID
instead of a pci device pointer. This can be used when the searched ID
is overridden for debugging or such a purpose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
tpa6140a2 uses different names for the regulators.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As noted by pl bossart <bossart.nospam@gmail.com>, the PCM I/O routines
(snd_pcm_lib_write1, snd_pcm_lib_read1) should block wake_up() calls
until all samples are not processed.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Do general cleanup in snd_pcm_update_hw_ptr*() routines and merge them.
The main change is hw_ptr_interrupt variable removal to simplify code
logic. This variable can be computed directly from hw_ptr.
Ensure that updated hw_ptr is not lower than previous one (it was possible
with old code in some obscure situations when interrupt was delayed or
the lowlevel driver returns wrong ring buffer position value).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In some debug cases, it might be usefull to see previous ring buffer
positions to determine position problems from the lowlevel drivers.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This is one of Sound Blaster Pro compatible chipsets which is supported
by Linux OSS driver and was missing native supoort for ALSA.
The Jazz16 audio codec is Crystal CS4216 which is capable
of playback and recording up to 48 kHz stereo.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8955 is a low power, high quality stereo DAC with integrated
headphone and loudspeaker amplifiers, designed to reduce external
component requirements in portable digital audio applications. This is
an initial driver implementing support for the majority of the
functionality in the device, currently OUT3 is not supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
There are now five copies of the code to allocate a PCM buffer using
vmalloc(). Add a sixth in the core so that the others can be removed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8904 is a high performance ultra-low power stereo CODEC
optimised for portable audio applications, with features including
a class W amplifier, FLL with free running mode, Mobile ReTune and
ground referenced headphone and line outputs.
Support for some features, most particularly the digital microphone
interface, is not yet present.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The ACI mixer is used to control the radio FM module
installed on the Miro PCM20 sound card. Expose ACI mixer
outside the sound card driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the miro.h header to the include/sound directory. It can
be used in the Miro PCM20 radio driver (v4l).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update control names to be more closer to their meaning.
Change the "Mono" name to the "Beep" as this line is usually
used to forward the PC beeper signal to sound card's output.
Update names for both cs423x and wss.
Clean up cs4235 controls according to the cs4235 doc. Rename
some of the cs4235 controls to be consistent with the cs4236's
ones.
Also, delete one misnamed cs4231 register define.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The jack_status_check callback function is the interface to check the
status of the jack. Some target provides the method to distinguish what
is the jack inserted - headphone jack, microphone jack, tvout jack, etc,
so we can implement it using the jack_status_check function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many devices need to calculate the bit clock rate desired to
work out the clock configuration required for the device.
Provide utility functions to do this using both hw_params
structures and raw numbers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Record the pid of the task that opened a RawMIDI substream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Record the pid of the task that opened a PCM substream. For sound
cards with hardware mixing, this allows determining which process
is associated with a specific substream's volume control.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of storing the PID number, take a reference to the task's pid
structure. This protects against duplicates due to PID overflows, and
using pid_vnr() ensures that the PID returned by snd_ctl_elem_info() is
correct as seen from the current namespace.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We do not need to save the ID of the process that locked a control
because that information is already available in the owner's file data.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The cs4236 was two step detection with call to the snd_wss_free()
between two steps. The snd_wss_free() did not free a sound device
created in the snd_wss_create(). This caused an OOPS during module
removal as the same sound device was released twice. The same OOPS
happened if the cs4236 module loading failed.
Fix this by adapting the snd_cs4236_create() to correctly work with
chips less capable then cs4236. The snd_cs4236_create() behaves the
same as the snd_wss_create() if the chip is less capable than the cs4236.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a port of the sound/oss/sh_dac_audio.c driver.
The driver uses an on-chip 8-bit D/A converter, which has a speaker connected
to one of its channels, found in several ancient HP machines.
For interrupts it uses a high-resolution timer (hrtimer).
Tested on SH7709 based hp6xx (HP Jornada 680/690 and HP Palmtop 620lx/660lx).
Also, since OSS Emulation works, the old OSS sound/oss/sh_dac_audio.c driver
would be obsolete soon, and it could be removed.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_soc_init_card() is always called as the last part of the CODEC probe
function so we can factor it out into the core card setup rather than
have each CODEC replicate the code to do the initialiastation. This will
be required to support multiple CODECs per card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Driver for Texas Instruments TLV320DAC33 (SLAS546) low power stereo
audio DAC.
TLV320DAC33 is a stereo audio codec with integrated 24KB FIFO for low
power audio playback.
The digital interface can use I2S, DSP (A or B), Right and Left
justified formats.
DAC33 has stereo analog input, which can be bypassed to the analog
outputs.
Regarding to the internal 24KB FIFO the driver implements 'FIFO bypass'
mode (default) and nSample mode (FIFO is in use).
a) In 'FIFO bypass' mode the internal FIFO is not in use, the codec is
working synchronously as a normal codec (it needs constant stream of
data on the digital interface).
b) The nSample mode implementation uses one interrupt line from DAC33 to
the host:
Alarm threshold is set to 10ms of audio data (limit by the driver
implementation).
DAC33 will signal an interrupt, when the FIFO level goes under the
Alarm threshold.
The host will write to nSample register a value (number of stereo
samples), to tell DAC33 how many samples it should read in a burst from
the host. When the DAC33 received the number of samples, it disables the
clocks on the I2S bus. When the FIFO use again goes under the Alarm
threshold, DAC33 signals the host with an interrupt, and the process is
repeated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PM core will grow pm_link infrastructure in 2.6.33 which can be
used to implement the intended functionality of the ASoC-specific
device suspend and resume callbacks so drop them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Driver for Texas Instruments TPA6130A2 stereo headphone
amplifier.
The driver provides playback gain control and also pre-defined
DAPM_HP widgets and DAPM routings for power management.
The DAPM_HP widget names are:
"TPA6130A2 Headphone Left"
"TPA6130A2 Headphone Right"
From soc machine drivers to use with the tpa6130a2 amplifier,
the tpa6130a2_add_controls has to be called, which adds the alsa
controls and the DAPM routing needed for the tpa6130a2.
After that the machine driver can connect the codec's output
with 'TPA6130A2 Left' and 'TPA6130A2 Right':
{"TPA6130A2 Left", NULL, "CODEC LEFT OUT"},
{"TPA6130A2 Right", NULL, "CODEC RIGHT OUT"},
Internally the left and right channels are powered separately.
When none of the channels are needed the amplifier is powered
down:
hard power: valid GPIO number is passed within platform data
soft power: Using the software shutdown of the amplifier
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes it is desirable to have a mux which does not reflect any
direct register configuration but which will instead only have an
effect implicitly (for example, as a result of changing which parts
of the device are powered up). Provide a virtual mux for this purpose.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to support multiple codecs on the same system in the debugfs
the directory hierarchy need to be changed by adding directory per codec
under the asoc direcorty:
debugfs/asoc/{dev_name(socdev->dev)}-{codec->name}/codec_reg
/dapm_pop_time
/dapm/{widgets}
With the original implementation only the debugfs files are only
created for the first codec, other codecs loaded later would fail to
create the debugfs files (since they are already exist).
Furthermore in this situation any of the codecs has been removed, would
cause the debugfs entries to disappear, regardless if the codec, which
created them are still loaded (the one which loaded first).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The conversion solves the problem that firmware size was set to 64KB
while non PnP cards have 128KB firmware files.
An additional firmware initialization code has been moved from the OSS
driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add DAI format definition for PDM interfaces.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* complete support for ak4113
* based on code for ak4114 and ak4117
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* complete support for ak4620
* codec regs listed in proc for all codecs/chips
* adding total regs for each codec
* fixing nb. of steps in input attenuation controls
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* the previous version had a typo - values of AK4114_OPS10-12 were
identical with AK4114_OPS00-02
* Since no cards actually use this feature, the bug was not identified earlier
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch adds an interface to set the relationship between audio
channel number and slot number. The interface should be really useful
because audio channel n doesn't always use slot n in all platforms. And
for some devices, the relationship even can change with sound mode
switch in 2.1,3.1,4.1,5.1,6.1,7.1 etc.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* topic/tlv-minmax:
ALSA: usb-audio - Correct bogus volume dB information
ALSA: usb-audio - Use the new TLV_DB_MINMAX type
ALSA: Add new TLV types for dBwith min/max
Some chips with complex internal supply (particularly clocking)
arragements may have multiple options for some of the supply
connections. Since these don't affect user-visible audio routing
the expectation would be that they would be managed automatically
by one of the drivers.
Support these users by allowing routes to have a connected function
which is queried before the connectedness of the path is checked as
normal. Currently this is only done for supplies, other widgets
could be supported but are not currently since the expectation for
them is that audio routing will be under the control of userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add appropriate const prefix to char * arguments in proc helper functions.
Also fixed the caller side to be proper const pointers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Re-export snd_pcm_format_name() function to be used outside the PCM core.
As a first example, usbaudio is changed to use it now again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The struct snd_monitor_file is used locally only in sound/core/init.c,
thus it should be moved there from the public sound/core.h.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More and more devices feature PLLs and FLLs with the ability to select
between multiple input clocks. In order to better support these devices
a new argument, source, has been added to the set_pll() configuration
API. Using set_clkdiv() is often difficult due to the need to stop the
PLL/FLL before any reconfiguration can be done.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add debug module option to snd core.
This controls the debug print level. When CONFIG_SND_DEBUG_VERBOSE
is set, you can suppress the debug messages by giving or changing this
parameter to a lower value. debug=0 means no debug messsages.
As default, it's set to the verbose level 2.
Since this option can be changed dynamically via sysfs file, you can
suppress the verbose debug messages on the fly, which wasn't possible
before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently when built with DEBUG DAPM will dump information about
the power state decisions it is taking for each widget to dmesg.
This isn't an ideal way of getting the information - it requires
a kernel build to turn it on and off and for large hub CODECs the
volume of information is so large as to be illegible. When the
output goes to the console it can also cause a noticable impact
on performance simply to print it out.
Improve the situation by adding a dapm directory to our debugfs
tree containing a file per widget with the same information in
it. This still requires a decision to build with debugfs support
but is easier to navigate and much less intrusive.
In addition to the previously displayed information active streams
are also shown in these files.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver is very simple.
It support playback only now.
This patch is tested by ms7724se board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently DAPM interfaces with the audio streams to and from the
processor at the DAC and ADC widgets. As the digital capabilities
of parts increases this is becoming a less and less able to meet
the needs of parts.
To meet the needs of these devices create new widgets interfacing
with the TDM bus but not integrated into any other functionality.
Audio can then be routed to and from these widgets using existing
routing widgets.
A slot number is provided in the definition but this is currently
not used yet. This is intended to support devices which can use
more than one TDM slot on a single interface.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for passing platform data to ac97 bus devices
from PXA2xx-AC97 driver..
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the interval timer to be programmed with its full 96 kHz
precision.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Extend set_tdm_slot to allow the user to arbitrarily set the frame width
and active TX/RX slots.
Updates magician.c and wm9081.c for the new set_tdm_slot(). wm9081.c
still doesn't handle the slot_width override.
While being there, correct an incorrect use of SlotsPerFrm(7) use in
bitmask on pxa-ssp.c (SSCR0_SlotsPerFrm(x) is (((x) - 1) << 24)) ).
(this series is meant for Mark's for-2.6.32 branch)
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As part of this refactoring the type of the CODEC hw_read operation
is changed to match the regular read operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While writes tend to be able to use a fairly bus independant format to
do the writes reads are all bus specific. To allow us to factor out
this code include the bus type as a parameter when setting up the
cache.
Initially just use this to factor out hw_write_t for I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This helps CODECs with sparse register maps work better with the
register cache display interface.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch allows passing platform_data to devices attached to AC97 bus
(like touchscreens, battery measurement chips ...).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a macro for double controls with special callback function and
TLV. The SOC_DOUBLE_R_EXT_TLV needs two registers and one shift for
double controls.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a macro for double controls with special callback function and
TLV. The SOC_DOUBLE_EXT_TLV needs one register and two shifts for double
controls.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8993 is a highly integrated ultra-low power hi-fi CODEC designed
for portable devices such as multimedia phones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using SG-buffers with dma_alloc_coherent() is often very inefficient
on non-coherent architectures because a tracking record could be
allocated in addition for each dma_alloc_coherent() call.
Instead, simply disable SG-buffers but just allocate normal continuous
buffers on non-supported (currently all but x86) architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A lot of CODECs share the same register data formats and therefore
replicate the code to manage access to and caching of the register
map. In order to reduce code duplication centralised versions of
this code will be introduced with drivers able to configure the use
of the common code by calling the new snd_soc_codec_set_cache_io()
API call during startup.
As an initial user the 7 bit address/9 bit data format used by many
Wolfson devices is supported for write only CODECs and the drivers
with straightforward register cache implementations are converted to
use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a volatile_register() operation to the CODEC structure providing a
standard operation to query if a register is volatile. This will be used
to factor out the register cache I/O operations for the CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the audio subsystem is powered down cleanly when the system
shuts down by providing a shutdown operation. This ensures that all the
components have been returned to an off state cleanly which should avoid
audio issues from partially charged capacitors or noise on digital inputs
if the system is restarted quickly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Ben Dooks <ben-linux@fluff.org>
Add new types for TLV dB scale specified with min/max values instead
of min/step since the resolution can't match always with the one
a device provides. For example, usb audio devices give 1/256 dB
resolution while ALSA TLV is based on 1/100 dB resolution.
The new min/max types have less problems because the possible
rounding error happens only at min/max.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch mostly follows commit 5998102b90
"ASoC: Refactor WM8731 device registration" to make UDA1380 use standard
device instantiation. Similarly, the I2C device registration temporarily
moves into the magician machine driver before it will find its final
resting place in the board file.
At the same time, platform specific configuration is moved to platform data
and common power/reset GPIO handling moves into the codec driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that ASoC subdevices can be regular devices they can have normal
suspend and resume calls from their buses. However, suspending them
individually is not desirable since this can lead to problems such as
pops and clicks from devices being suspended with their signals being
amplified or clocks being stopped suddenly.
This will be resolved by having the normal device model suspend and
resume calls call into ASoC which will suspend the entire card while any
of its components are suspended. At present this is not yet implemented
but in order to aid the transition of drivers to the standard device
model this patch adds API calls for the notifications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* topic/pcm-jiffies-check:
ALSA: pcm - A helper function to compose PCM stream name for debug prints
ALSA: pcm - Fix update of runtime->hw_ptr_interrupt
ALSA: pcm - Fix a typo in hw_ptr update check
ALSA: PCM midlevel: lower jiffies check margin using runtime->delay value
ALSA: PCM midlevel: Do not update hw_ptr_jiffies when hw_ptr is not changed
ALSA: PCM midlevel: introduce mask for xrun_debug() macro
ALSA: PCM midlevel: improve fifo_size handling
* topic/asoc: (135 commits)
ASoC: Apostrophe patrol
ASoC: codec tlv320aic23 fix bogus divide by 0 message
ASoC: fix NULL pointer dereference in soc_suspend()
ASoC: Fix build error in twl4030.c
ASoC: SSM2602: assign last substream to the master when shutting down
ASoC: Blackfin: document how anomaly 05000250 is handled
ASoC: Blackfin: set the transfer size according the ac97_frame size
ASoC: SSM2602: remove unsupported sample rates
ASoC: TWL4030: Check the interface format for 4 channel mode
ASoC: TWL4030: Use reg_cache in twl4030_init_chip
ASoC: Initialise dev for the dummy S/PDIF DAI
ASoC: Add dummy S/PDIF codec support
ASoC: correct print specifiers for unsigneds
ASoC: Modify mpc5200 AC97 driver to use V9 of spin_event_timeout()
ASoC: Switch FSL SSI DAI over to symmetric_rates
ASoC: Mark MPC5200 AC97 as BROKEN until PowerPC merge issues are resolved
ASoC: Fabric bindings for STAC9766 on the Efika
ASoC: Support for AC97 on Phytec pmc030 base board.
ASoC: AC97 driver for mpc5200
ASoC: Main rewite of the mpc5200 audio DMA code
...
They are now only accessed within dapm_power_widgets() so can be local
to that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the remaining unsigned shorts with unsigned ints.
Tested with pcap2 codec (25 bits registers).
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce snd_card_set_id() function to allow lowlevel drivers to set
default identification name for card slot. The function checks also
for identification name collisions and tries to create unique name.
Also, the snd_card_create() function is simplified, because this new
function is used. As bonus, proper name collision checks are evaluated
at the card create time.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the fifo_size assignment to hw->ioctl callback to allow lowlevel
drivers overwrite the default behaviour.
fifo_size is in frames not bytes as specified in asound.h and alsa-lib's
documentation, but most hardware have fixed byte based FIFOs. Introduce
internal SNDRV_PCM_INFO_FIFO_IN_FRAMES.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM9081 is designed to provide high power output at low distortion
levels in space-constrained portable applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Should be no impact on the generated code but it helps the compiler
print clearer messages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than managing the bias level of the system based on if there is
an active audio stream manage it based on there being an active DAPM
widget. This simplifies the code a little, moving the power handling
into one place, and improves audio performance for bypass paths when no
playbacks or captures are active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM has always applied any changes to the power state of widgets as soon
as it has determined that they are required. Instead of doing this store
all the changes that are required on lists of widgets to power up and
down, then iterate over those lists and apply the changes. This changes
the sequence in which changes are implemented, doing all power downs
before power ups and always using the up/down sequences (previously they
were only used when changes were due to DAC/ADC power events). The error
handling is also changed so that we continue attempting to power widgets
if some changes fail.
The main benefit of this is to allow future changes to do optimisations
over the whole power sequence and to reduce the number of walks of the
widget graph required to check the power status of widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added runtime->delay field to adjust the delayed samples for snd_pcm_delay().
Typically a hardware FIFO length is stored in this field, so that the
extra delay between hwptr and applptr can be computed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DAI structure has two pointers to the codec, one in the body of the
DAI and one in a union for a parent pointer. Drop the parent pointer
version.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The defines for TDM and synchronous clocks are not used - they are
mostly a legacy of the automatic clocking configuration. TDM will
require configuration of the number of timeslots and which ones to use
so can't be fit into the DAI format and synchronous mode is handled by
symmetric_rates (and needs to be done by constraints rather than when
the DAI format is being configured).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The AC97 wire format is completely fixed so CODECs don't have any choice
about the formats they accept but controllers accept a variety of data
formats and render them down onto the bus. Have a shared define so all
the CODEC drivers will interoperate with any of our controller drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a macro for double controls with special callback functions.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.
Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.
Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently there are two possible platform datas for the PXA AC97 driver:
one supported by the generic AC97 driver only which provides callbacks
to allow board-specific configuration at stream startup and teardown,
and another for pxa2xx-ac97-lib which allows configuration of the reset
GPIO for PXA2xx CPUs.
Obviously this won't actually work when using the generic AC97 driver
since the drivers will attempt to parse the platform data in both
formats. Fix this by merging the two structures.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Added private_data and private_free fields to struct snd_jack so that
the caller can assign the data. It'll be helpful for avoiding the
double-free of the jack instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some drivers like Intel8x0 or Intel HDA are broken for some hardware variants.
This patch adds more strict buffer position checks based on jiffies when
internal hw_ptr is updated. Enable xrun_debug to see mangling of wrong
positions.
As a side effect, the hw_ptr interrupt update routine might do slightly better
job when many interrupts are lost.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Many devices require symmetric configurations of capture and playback
data formats, often due to shared clocking but sometimes also due to
other shared playback and record configuration in the device. Start
providing core support for this by allowing the DAIs or the machine
to specify that the sample rates used should be kept symmetric.
A flag symmetric_rates is provided in the snd_soc_dai and
snd_soc_dai_link structures. If this is set in either of the DAIs or in
the machine then a constraint will be applied when a stream is already
open preventing any changes in sample rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Impact: cleanup
The earlier patch 'make most exported headers use strict integer
types' accidentally includes <linux/types.h> both from the common and
from the kernel-only parts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This takes care of all files that have only a small number
of non-strict integer type uses.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Cc: linux-ppp@vger.kernel.org
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A number of standard posix types are used in exported headers, which
is not allowed if __STRICT_KERNEL_NAMES is defined. In order to
get rid of the non-__STRICT_KERNEL_NAMES part and to make sane headers
the default, we have to change them all to safe types.
There are also still some leftovers in reiserfs_fs.h, elfcore.h
and coda.h, but these files have not compiled in user space for
a long time.
This leaves out the various integer types ({u_,u,}int{8,16,32,64}_t),
which we take care of separately.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Cc: linux-ppp@vger.kernel.org
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It depends on L3 support from 2.4 kernel (CONFIG_L3) that never got
merged into mainline. Since there's no way to use it on any of
supported machines (iPaq h3100 or h3600), better drop it for now.
It can be reimplemented later using ASoC infrastructure (there's
already a driver for uda1341 codec in mainline, so only CPU and machine
parts need to be written).
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the PXA27x series allow 2 gpios to reset the ac97 bus,
allow through platform data configuration the definition of
the correct gpio which will reset the AC97 bus.
This comes from a silicon defect on the PXA27x series, where
the gpio must be manually controlled in warm reset cases.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge Eric Maio's patch to merge snd_soc_dai_ops out of line. Fixed
merge issues and updated drivers, plus an issue with the ops for the two
s3c2443 AC97 DAIs having been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use define instead of enum for ioctl definitions since strace can't
parse ioctls defined via enum properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the standard linked list for snd_monitor_file management.
Also, move the list deletion of shutdown_list element into
snd_disconnect_release() (for simplification).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added snd_ctl_add_slave_uncached() function to add a slave element
with volatile controls. The values of normal slave elements are
supposed to be cachable, i.e. they are changed only via the put
callbacks. OTOH, when a slave element is volatile and its values may
be changed by other reason (e.g. hardware status change), the values
will get inconsistent.
The new function allows the slave elements with volatile changes.
When the slave is tied with this call, the native get callback is
issued at each time so that the values are always updated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The timer callbacks are called in the protected status by the lock
of the timer instance, so there is no need for an extra lock in the
PCM substream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Considering the fact that most cpu_dai or codec_dai are using a same
'snd_soc_dai_ops' for several similar interfaces, 'ops' would be better
made a pointer instead, to make sharing easier and code a bit cleaner.
The patch below is rather preliminary since the asoc tree is being
actively developed, and this touches almost every piece of code,
(and possibly many others in development need to be changed as
well). Building of all codecs are OK, yet to every SoC, I didn't test
that.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add GPIO support to jack reporting framework in ASoC using gpiolib calls.
The gpio support exports two new functions: snd_soc_jack_add_gpios and
snd_soc_jack_free_gpios.
Client drivers using gpio feature must pass an array of jack_gpio pins
belonging to a specific jack to the snd_soc_jack_add_gpios function. The
framework will request the gpios, set the data direction and request irq.
The framework will update power status of related jack_pins when an event on
the gpio pins comes according to the reporting bits defined for each gpio.
All gpio resources allocated when adding jack_gpio pins can be released
using snd_soc_jack_free_gpios function.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On some systems it is desirable for control for DAPM pins to be provided
to user space. This is the case with things like GSM modems which are
controlled primarily from user space, for example. Provide a helper which
exposes the state of a DAPM pin to user space for use in cases like this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
cs4232 and cs4236 driver merge to solve PnP BIOS detection.
Also, the patch adds recognition if the chip is cs4236b+
or earlier part. This unifies drivers for both cs4232
and cs4236+ chips. It allows to use the PnP BIOS
detection for the cs4236+ chips. Previously, only
the snd-cs4232 could be detected by the PnP BIOS.
The cs4232+ cards reports two separate PnP BIOS ids.
The patch adds search for the second id to find out
resources assigned to a control port.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds ALSA support for the AC97 controller found on Atmel
AVR32 devices.
Tested on ATSTK1006 + ATSTK1000 with a development board with a AC97
codec.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds ALSA support for the Audio Bistream DAC found on Atmel
AVR32 devices. The ABDAC is an Atmel IP which might show up on AT91
devices in the future, hence making a generic driver which can be
utilized by AT91 arch if needed.
Datasheet describing the ABDAC peripheral is available in the AT32AP7000
datasheet, http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Tested on ATSTK1006 + ATSTK1000 with a class D amplifier stage.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Impact: cleanup
snd_pcm_new takes a char *id argument, although it is not modifying
the string. it can therefore be declared as const char *id.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fix the following 'make headers_check' warning:
usr/include/sound/hdsp.h:33: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Introduced snd_card_create() function as a replacement of snd_card_new().
The new function returns a negative error code so that the probe callback
can return the proper error code, while snd_card_new() can give only NULL
check.
The old snd_card_new() is still provided as an inline function but with
__deprecated attribute. It'll be removed soon later.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many codec drivers were implementing cookie-cutter copies of the function
that adds kcontrols to the codec.
This patch moves this code to a common function snd_soc_add_controls() in
soc-core.c and updates all drivers using copies of this function to use the
new common version.
[Edited to raise priority of error log message and document parameters.
-- broonie]
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a jack reporting interface to ASoC. This wraps the ALSA
core jack detection functionality and provides integration with DAPM to
automatically update the power state of pins based on the jack state.
Since embedded platforms can have multiple detecton methods used for a
single jack (eg, separate microphone and headphone detection) the report
function allows specification of which bits are being updated on a given
report.
The expected usage is that machine drivers will create jack objects and
then configure jack detection methods to update that jack.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge the recently introduced soc_value_enum structure to the soc_enum.
The value based enums are still handled separately from the normal enum types,
but with the merge some of the newly introduced functions can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch allows you to define the mixer paths as having the same name as the
paths they represent.
This is required to support codecs such as the wm9705 neatly without extra
controls in the alsa mixer.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Add support for reporting new jack types SND_JACK_VIDEOOUT and
SND_JACK_AVOUT (a combination of LINEOUT and VIDEOOUT) to the jack
reporting API.
Also add the corresponding SW_VIDEOOUT_INSERT switch to the input system
header.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch introduces a new enum type.
In this enum type each enumerated items referred with a value.
This new enum type can handle enums encoded in bitfield, or any other
weird ways. twl4030 codec has several mux selection register, where the
input/output mux is coded in a bitfield. With the normal enum type this type
of mux can not be handled in a clean way.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use a lookup table rather than explicit code to map input subsystem jack
types into ASoC ones, implemented as suggested by Takashi Iwai.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'd like to use the High Pass Filter and V_REFOUT bitshift values elsewhere,
so stick them into a ac97_codec.h.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Another part of the backporting of Liam's ASoC v2 work. Using this is
more complicated than the other registration types since currently the
codec is instantiated during the probe of the ASoC device so we can't
currently readily wait for the codec to register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some systems support both mechanical and electrical jack detection,
allowing them to report that a jack is physically present but does
not have any functioning connections. Add a new jack type for these,
allowing user space to report faulty connections.
Thanks to Guillem Jover for the suggestion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC v2 allows platform drivers to instantiate independantly of the
overall ASoC card. This API allows drivers to notify the core when
they are registered.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add API calls to register and unregister DAIs with the core. Currently
these APIs are ineffective. Since multiple DAIs for a given device are
a common case bulk variants are provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC v2 allows cards, codecs and platforms to instantiate separately,
with the overall ASoC device only being instantiated once all the
required components have registered. As part of backporting Liam's work
introduce an initial version of the card registration functions. At
present these do nothing active and are internal only, they will be
exposed to machine drivers after further backporting. Adding this now
allows the datastructures used for dynamic card instantiation to be
built up gradually.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
None of the platforms are actually using the SoC device so remove it
(only atmel actually has a suspend method).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is in preparation for the removal of struct snd_soc_device.
The pop time configuration should really be a property of the card not
the codec but since DAPM currently uses the codec rather than the card
using the codec is fine for now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As part of the deprecation of snd_soc_device push the registration of
the platform down into the card structure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC v2 does not use the struct snd_soc_device at runtime, using struct
snd_soc_card as the root of the card. Begin removing data from
snd_soc_device by pushing the workqueue data into snd_soc_card, using a
backpointer to the snd_soc_device to keep things going for the time
being.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC card initialisation is completed by a function called
snd_soc_register_card(). As part of the work to allow independant
registration of cards, codecs and machines in ASoC v2 a new function of
the same name has been added so rename the existing function to
facilitate the merge of v2.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAI type information is only ever used within ASoC in order to special
case AC97 and for diagnostic purposes. Since modern CPUs and codecs
support multi function DAIs which can be configured for several modes
it is more trouble than it's worth to maintain anything other than a
flag identifying AC97 DAIs so remove the type field and replace it with
an ac97_control flag.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Liam Girdwood's ASoC v2 work avoids having two different ops structures
for DAIs by merging the members of struct snd_soc_ops into struct
snd_soc_dai_ops, allowing per DAI configuration for everything.
Backport this change.
This paves the way for future work allowing any combination of DAIs to
be connected rather than having fixed purpose CODEC and CPU DAIs and
only allowing CODEC<->CPU interconnections.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC v2 factors most of the contents of soc.h out into separate headers,
including soc-dai.h for the DAI. Factor the existing DAI API out into
this file in order to prepare for backporting of the ASoC v2 DAI API.
Also backport some of Liam's improvements to the documentation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the issues with the ASoC v1 API which has been addressed in the
ASoC v2 work that Liam Girdwood has done is that the ALSA card provided
by ASoC is distributed around the ASoC structures. For example, machine
wide data such as the struct snd_card are maintained as part of the
CODEC data structure, preventing the use of multiple codecs. This has
been addressed by refactoring the data structures so that all the data
for the ALSA card is contained in a single structure snd_soc_card which
replaces the existing snd_soc_machine and snd_soc_device.
Begin the process of backporting this by renaming struct snd_soc_machine
to struct snd_soc_card, better reflecting its function and bringing it
closer to standard ALSA terminology.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change coding style to be more acceptable by checkpatch.pl.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change snd_BUG_ON() to evaluate the given condition, at least, in syntax
for avoiding compile warnings such as unused variables. The compiler
should optimize out the condition evaluation in the real code, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dimitris Papastamos
Jarkko Nikula
Liam Girdwood
Mark Brown
Linus Torvalds
Takashi Iwai
Kay Sievers
Arnaud Patard (Rtp)
Nobuhiro Iwamatsu
Mike Frysinger
Mika Westerberg
Kuninori Morimoto
Jaroslav Kysela
Sam Ravnborg
Peter Ujfalusi
James Bottomley
David Dillow
Vladimir Zapolskiy
apatard@mandriva.com
Ben Collins
Daniel Mack
Mark Gross
Krzysztof Helt
Dan Carpenter
Jassi Brar
jassi brar
Guennadi Liakhovetski
Ilkka Koskinen
Clemens Ladisch
André Goddard Rosa
Jean Delvare
Joonyoung Shim
Rafael Ignacio Zurita
Lopez Cruz, Misael
Pavel Hofman
Barry Song
Kuninori Morimoto
Marek Vasut
Daniel Ribeiro
Peter Meerwald
Philipp Zabel
Jon Smirl
Russell King
Mauro Carvalho Chehab
Arnd Bergmann
Dmitry Artamonow
Robert Jarzmik
Eric Miao
Andreas Mohr
Hans-Christian Egtvedt
Tim Blechmann
Jaswinder Singh Rajput
Takashi Iwai
Ian Molton
Jani Nikula
Hans Verkuil
Andres Salomon
Christian Pellegrin