If the CAN net device has been successfully allocated, its private
data structure is impossible to be empty, remove this redundant error
return judgment.
Link: https://lore.kernel.org/r/20210205072559.13241-2-xulin.sun@windriver.com
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds "ONE-SHOT" mode support to the following CAN-USB
PEAK-System GmbH interfaces:
- PCAN-USB X6
- PCAN-USB FD
- PCAN-USB Pro FD
- PCAN-Chip USB
- PCAN-USB Pro
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch makes it possible to specifically flash the LED of a CAN
port of the CAN-USB interfaces of PEAK-System.
Link: https://lore.kernel.org/r/20210309122141.3276927-1-mkl@pengutronix.de
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: use common prefix PCAN_ for defines]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the plain integers used for flags in
pcan_usb_pro_encode_msg() by macros which are already defined.
Link: https://lore.kernel.org/r/20210309082128.23125-4-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
struct ucan_message_in contains member with 4-byte alignment
but is itself marked as unaligned, which triggers a warning:
drivers/net/can/usb/ucan.c:249:1: warning: alignment 1 of 'struct ucan_message_in' is less than 4 [-Wpacked-not-aligned]
Mark the outer structure to have the same alignment as the inner
one.
Link: https://lore.kernel.org/r/20210204162625.3099392-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On ARCHs without IOMEM support the grcan driver fails to link due to
missing iomem functionality. This patch adds the missing Kconfig
dependency to HAS_IOMEM.
Link: https://lore.kernel.org/r/20210309140424.3331010-1-mkl@pengutronix.de
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add three macro to simplify the readability of big bit timing numbers:
- CAN_KBPS: kilobits per second (one thousand)
- CAN_MBPS: megabits per second (one million)
- CAN_MHZ: megahertz per second (one million)
Example:
u32 bitrate_max = 8 * CAN_MBPS;
struct can_clock clock = {.freq = 80 * CAN_MHZ};
instead of:
u32 bitrate_max = 8000000;
struct can_clock clock = {.freq = 80000000};
Apply the new macro to driver/net/can/dev/bittiming.c.
Link: https://lore.kernel.org/r/20210306054040.76483-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The logic for the tdco calculation is to just reuse the normal sample
point: tdco = sp. Because the sample point is expressed in tenth of
percent and the tdco is expressed in time quanta, a conversion is
needed.
At the end,
ssp = tdcv + tdco
= tdcv + sp.
Another popular method is to set tdco to the middle of the bit:
tdc->tdco = can_bit_time(dbt) / 2
During benchmark tests, we could not find a clear advantages for one
of the two methods.
The tdco calculation is triggered each time the data_bittiming is
changed so that users relying on automated calculation can use the
netlink interface the exact same way without need of new parameters.
For example, a command such as:
ip link set canX type can bitrate 500000 dbitrate 4000000 fd on
would trigger the calculation.
The user using CONFIG_CAN_CALC_BITTIMING who does not want automated
calculation needs to manually set tdco to zero.
For example with:
ip link set canX type can tdco 0 bitrate 500000 dbitrate 4000000 fd on
(if the tdco parameter is provided in a previous command, it will be
overwritten).
If tdcv is set to zero (default), it is automatically calculated by
the transiver for each frame. As such, there is no code in the kernel
to calculate it.
tdcf has no automated calculation functions because we could not
figure out a formula for this parameter.
Link: https://lore.kernel.org/r/20210224002008.4158-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix the warning triggered by having an '=' at the beginning of the
line by moving it back to the previous line. Also replace all
indentations with a single space so that future entries can be more
easily added.
Extract of ./scripts/checkpatch.pl -f drivers/net/can/dev/netlink.c:
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_BITTIMING_CONST]
+ = { .len = sizeof(struct can_bittiming_const) },
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_DATA_BITTIMING]
+ = { .len = sizeof(struct can_bittiming) },
CHECK: Assignment operator '=' should be on the previous line
+ [IFLA_CAN_DATA_BITTIMING_CONST]
+ = { .len = sizeof(struct can_bittiming_const) },
Link: https://lore.kernel.org/r/20210224002008.4158-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stack
even if the transmission failed for some reason.
To avoid to calculate this length twice, extend can_free_echo_skb() to
return that value. Convert all users of this function, too.
This patch is the natural extension of commit:
| 9420e1d495 ("can: dev: can_get_echo_skb(): extend to return can
| frame length")
Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A out of bounds access to "struct can_priv::echo_skb" leads to a
kernel crash. Better print a sensible warning message instead and try
to recover.
This patch is similar to:
| e7a6994d04 ("can: dev: __can_get_echo_skb(): Don't crash the kernel
| if can_priv::echo_skb is accessed out of bounds")
Link: https://lore.kernel.org/r/20210319142700.305648-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
So far the creation of the TX echo skb was optional and can be
controlled by the local sender of a CAN frame.
It turns out that the TX echo CAN skb can be piggybacked to carry
information in the driver from the TX- to the TX-complete handler.
Several drivers already use the return value of
can_get_echo_skb() (which is the length of the data field in the CAN
frame) for their number of transferred bytes statistics. The
statistics are not working if CAN echo skbs are disabled.
Another use case is to calculate and set the CAN frame length on the
wire, which is needed for BQL support in both the TX and TX-completion
handler.
For now in can_put_echo_skb(), which is called from the TX handler,
the skb carrying the CAN frame is discarded if no TX echo is
requested, leading to the above illustrated problems.
This patch changes the can_put_echo_skb() function, so that the echo
skb is always generated. If the sender requests no echo, the echo skb
is consumed in __can_get_echo_skb() without being passed into the RX
handler of the networking stack, but the CAN data length and CAN frame
length information is properly returned.
Link: https://lore.kernel.org/r/20210309211904.3348700-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update Chandrasekar Ramakrishnan as maintainer for mcan mmio device driver as I
will be moving to a different role.
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dan Murphy's email address at ti.com doesn't work anymore, mails
bounce with:
| 550 Invalid recipient <dmurphy@ti.com> (#5.1.1)
For now remove all CAN related entries of Dan from the Maintainers
file.
Link: https://lore.kernel.org/r/20210228094218.40015-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove restriction blocking configuration of CQE compression when PTP rx
filter is set. Instead turn on indication for RX PTP, and try to reopen
the channels.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Update setting HW time-stamp to allow coexistence with CQE compression.
Turn on RX PTP indication and try to reopen the channels. On success,
coexistence with CQE compression is enabled. Otherwise, fall-back to
turning off CQE compression.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When opening PTP channel with MLX5E_PTP_STATE_RX set, add the
corresponding flow steering rules. Capture UDP packets with destination
port 319 and L2 packets with ethertype 0x88F7 and steer them into the RQ
of the PTP channel.
Add API that manages the flow steering rules to be used in the following
patches via safe_reopen_channels mechanism.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a new FS API which captures the ANY traffic from the traffic
classifier into a dedicated FS table. The table consists of a group
matching the ethertype and a must-be-last group which contains a default
rule redirecting the unmatched packets back to the RSS logic.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a new FS API which captures the UDP traffic from the traffic
classifier into a dedicated FS table. This API handles both UDP over
IPv4 and IPv6 in the same manner. The tables (one for UDPv4 and another
for UDPv6) consist of a group matching the UDP destination port and a
must-be-last group which contains a default rule redirecting the
unmatched packets back to the RSS logic.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Flow Steering levels are used to determine the order between the tables.
As of today, each one of these tables follows the TTC table, and hijacks
its traffic, and cannot be combined together for now. Putting them in
the same layer better reflects the situation.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When present, add the PTP RQ to the RX reporter.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Break RX diagnostics function into smaller helpers. This enables easier
enhancement in the next patch in the set.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add PTP-TIR and initiate its RQT to allow PTP-RQ to integrate into the
safe-reopen flow on configuration change. Add rx_ptp_support flag on a
profile and turn it on for ETH driver. With this flag set, create a
redirect-RQT for PTP-RQ.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Like PTP-TX, once the PTP-RX is opened, corresponding statistics appear.
Add indication that PTP-RX was ever opened: rx_ptp_opened. If any of the
PTP RX or TX were opened, display the PTP channel's statistics.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Enhance PTP channel to allow PTP without disabling CQE compression. Add
RQ, TIR and PTP_RX_STATE to PTP channel. When this bit is set, PTP
channel manages its RQ, and PTP traffic is directed to the PTP-RQ which
is not affected by compression.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add PTP TX state to PTP channel, which indicates the corresponding SQ is
available. Further patches in the set extend PTP channel to include RQ.
The PTP channel state will be used for separation and coexistence of RX
and TX PTP. Enhance conditions to verify the TX PTP state is set.
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add error handling in case of failure to send switching data path message
to the host.
Reported-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_min_tso_segs is now stored in u8, so max value is 255.
255 limit is enforced by proc_dou8vec_minmax().
We can therefore remove the gso_max_segs variable.
Fixes: 47996b489bdc ("tcp: convert elligible sysctls to u8")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]
Issue here is that:
- all dev_put() should be paired with a corresponding prior dev_hold().
- A driver doing a dev_put() in its ndo_uninit() MUST also
do a dev_hold() in its ndo_init(), only when ndo_init()
is returning 0.
Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.
Fixes: 919067cc84 ("net: add CONFIG_PCPU_DEV_REFCNT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]
Issue here is that:
- all dev_put() should be paired with a corresponding dev_hold(),
and vice versa.
- A driver doing a dev_put() in its ndo_uninit() MUST also
do a dev_hold() in its ndo_init(), only when ndo_init()
is returning 0.
Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.
ip6_gre for example (among others problematic drivers)
has to use dev_hold() in ip6gre_tunnel_init_common()
instead of from ip6gre_newlink_common(), covering
both ip6gre_tunnel_init() and ip6gre_tap_init()/
Note that ip6gre_tunnel_init_common() is not called from
ip6erspan_tap_init() thus we also need to add a dev_hold() there,
as ip6erspan_tunnel_uninit() does call dev_put()
[1]
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 0 PID: 8422 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Modules linked in:
CPU: 1 PID: 8422 Comm: syz-executor854 Not tainted 5.12.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:refcount_warn_saturate+0xbf/0x1e0 lib/refcount.c:31
Code: 1d 6a 5a e8 09 31 ff 89 de e8 8d 1a ab fd 84 db 75 e0 e8 d4 13 ab fd 48 c7 c7 a0 e1 c1 89 c6 05 4a 5a e8 09 01 e8 2e 36 fb 04 <0f> 0b eb c4 e8 b8 13 ab fd 0f b6 1d 39 5a e8 09 31 ff 89 de e8 58
RSP: 0018:ffffc900018befd0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff88801ef19c40 RSI: ffffffff815c51f5 RDI: fffff52000317dec
RBP: 0000000000000004 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff815bdf8e R11: 0000000000000000 R12: ffff888018cf4568
R13: ffff888018cf4c00 R14: ffff8880228f2000 R15: ffffffff8d659b80
FS: 00000000014eb300(0000) GS:ffff8880b9c00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055d7bf2b3138 CR3: 0000000014933000 CR4: 00000000001506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__refcount_dec include/linux/refcount.h:344 [inline]
refcount_dec include/linux/refcount.h:359 [inline]
dev_put include/linux/netdevice.h:4135 [inline]
ip6gre_tunnel_uninit+0x3d7/0x440 net/ipv6/ip6_gre.c:420
register_netdevice+0xadf/0x1500 net/core/dev.c:10308
ip6gre_newlink_common.constprop.0+0x158/0x410 net/ipv6/ip6_gre.c:1984
ip6gre_newlink+0x275/0x7a0 net/ipv6/ip6_gre.c:2017
__rtnl_newlink+0x1062/0x1710 net/core/rtnetlink.c:3443
rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3491
rtnetlink_rcv_msg+0x44e/0xad0 net/core/rtnetlink.c:5553
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
netlink_unicast_kernel net/netlink/af_netlink.c:1312 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1338
netlink_sendmsg+0x856/0xd90 net/netlink/af_netlink.c:1927
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:674
____sys_sendmsg+0x6e8/0x810 net/socket.c:2350
___sys_sendmsg+0xf3/0x170 net/socket.c:2404
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2433
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
Fixes: 919067cc84 ("net: add CONFIG_PCPU_DEV_REFCNT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We fix a warning from the htmldoc tool and an indentation error reported
by smatch. There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-03-29
This series contains updates to igc driver only.
Andre Guedes says:
Add XDP support for the igc driver. The approach implemented by this
series follows the same approach implemented in other Intel drivers as
much as possible for the sake of consistency.
The series is organized in two parts. In the first part, i.e. patches
from 1 to 4, igc_main.c and igc_ptp.c code is refactored in preparation
for landing the XDP support, which is introduced in the second part
(patches from 5 to 8).
As far as code organization is concerned, XDP-related helpers are
defined in a new file, igc_xdp.c, and are called by igc_main.c.
The features added by this series have been tested with the samples
provided in samples/bpf/: xdp1, xdp2, xdp_redirect_cpu, and
xdp_redirect_map.
Upcoming series will add support of UMEM and zero-copy features from
AF_XDP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MBIM protocol makes the mhi network interface asymmetric, ingress data
received from MHI is MBIM protocol, possibly containing multiple
aggregated IP packets, while egress data received from network stack is
IP protocol.
This changes allows a 'protocol' to specify its own MRU, that when
specified is used to allocate MHI RX buffers (skb).
For MBIM, Set the default MTU to 1500, which is the usual network MTU
for WWAN IP packets, and MRU to 3.5K (for allocation efficiency),
allowing skb to fit in an usual 4K page (including padding,
skb_shared_info, ...).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if skb is non-linear, due to MHI skb chaining, it is
linearized in MBIM RX handler prior MBIM decoding, causing extra
allocation and copy that can be as large as the maximum MBIM frame
size (32K).
This change introduces MBIM decoding for non-linear skb, allowing to
process 'large' non-linear MBIM packets without skb linearization.
The IP packets are simply extracted from the MBIM frame using the
skb_copy_bits helper.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable res is being initialized with a value that is
never read and it is being updated later with a new value.
The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a document describing the principles behind resilient next-hop groups,
and some notes about how to configure and offload them.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following make W=1 kernel build warning:
drivers/net/mdio.c:95: warning: expecting prototype for mdio_link_ok(). Prototype was for mdio45_links_ok() instead
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following make W=1 kernel build warning:
drivers/net/bonding/bond_main.c:982: warning: expecting prototype for change_active_interface(). Prototype was for bond_change_active_slave() instead
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following make W=1 kernel build warning:
drivers/net/phy/mdio-boardinfo.c:63: warning: expecting prototype for mdio_register_board_info(). Prototype was for mdiobus_register_board_info() instead
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Two sampling fixes
This patchset fixes two bugs in recent sampling submissions.
The first fix, in patch #3, prevents matchall rules with sample action
to be added in front of flower rules on egress. Patches #1-#2 are
preparations meant at avoiding similar bugs in the future. Patch #4 is a
selftest.
The second fix, in patch #5, prevents sampling from being enabled on a
port if already enabled. Patch #6 is a selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that two sampling rules cannot be configured on the same port with
the same trigger.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-port sampling triggers (i.e., ingress / egress) cannot be
enabled twice. Meaning, the below configuration will not result in
packets being sampled twice:
# tc filter add dev swp1 ingress matchall skip_sw action sample rate 100 group 1
# tc filter add dev swp1 ingress matchall skip_sw action sample rate 100 group 1
Therefore, reject such configurations.
Fixes: 90f53c53ec ("mlxsw: spectrum: Start using sampling triggers hash table")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can only offload matchall rules that do not match on a
protocol. Test that matchall rules that match on a protocol are vetoed.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform the priority check earlier in the function instead of repeating
it for every action. This fixes a bug that allowed matchall rules with
sample action to be added in front of flower rules on egress.
Fixes: 54d0e963f6 ("mlxsw: spectrum_matchall: Add support for egress sampling")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch moved the protocol check out of the action check, so
these if statements can now be converted to a switch statement. Perform
the conversion.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform the protocol check earlier in the function instead of repeating
it for every action. Example:
# tc filter add dev swp1 ingress proto ip matchall skip_sw action sample group 1 rate 100
Error: matchall rules only supported with 'all' protocol.
We have an error talking to the kernel
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xulin Sun
Stephane Grosjean
Arnd Bergmann
Michal Simek
Marc Kleine-Budde
Vincent Mailhol
Pankaj Sharma
Aya Levin
Haiyang Zhang
Eric Dumazet
Jon Maloy
David S. Miller
Loic Poulain
Colin Ian King
Petr Machata
Yang Yingliang
Ido Schimmel