1. Bump top level address-cells/size-cells nodes to 2 (to ensure all
down stream addresses are 64-bits, unless explicitly specified
otherwise (in "soc" bus with all peripherals)
2. "memory" also specified with address/size 2
3. Add a commented reference for PAE40 region beyond 4GB physical
address space
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
DW USB controller on HSDK hangs sometimes after SW reset, so
add reset handle to make possible to reset DW USB controller HW.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
1. Remove "0x" prefix from unit-address of node names
----------------------->8------------------------
sed -i 's/@0x/@/g' arch/arc/boot/dts/*.dts*
----------------------->8------------------------
2. Make all hex addresses lowercase:
----------------------->8------------------------
sed -i 's/@\([0-9A-Za-z]*\)/@\L\1/g' arch/arc/boot/dts/*.dts*
sed -i 's/0x\([0-9A-Za-z]*\)/0x\L\1/g' arch/arc/boot/dts/*.dts*
----------------------->8------------------------
Inspired by [1] and the like.
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/13612017/
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Enable GPIO support on HSDK. HSDK SoC includes Synopsys
DesignWare DW_apb_gpio IP with 24 GPIOs mapped onto port A.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Mark DMA devices on AXS103 and HSDK boards connected through IOC
port as dma-coherent.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Otherwise kernel uses random MAC which is not very conveniet.
With that change in place use might set desired MAC in U-Boot
with "setenv ethaddr 11:22:33:44:55:66", save environment and
then from boot to boot the same MAC will be used by the kernel.
One other note for this to happen it's required to pass
board's .dtb in U-Boot's "bootm" command like that:
------------------->8-----------------
bootm 0x82000000 - 0x84000000
------------------->8-----------------
Here 0x82000000 is location of uImage while
0x80000000 is location of either axs10x.dtb or hsdk.dtb
previously loaded from SD-card, USB storage or TFTP server.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: stable@vger.kernel.org # 4.14
Cc: devicetree@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
GNU Make automatically deletes intermediate files that are updated
in a chain of pattern rules.
Example 1) %.dtb.o <- %.dtb.S <- %.dtb <- %.dts
Example 2) %.o <- %.c <- %.c_shipped
A couple of makefiles mark such targets as .PRECIOUS to prevent Make
from deleting them, but the correct way is to use .SECONDARY.
.SECONDARY
Prerequisites of this special target are treated as intermediate
files but are never automatically deleted.
.PRECIOUS
When make is interrupted during execution, it may delete the target
file it is updating if the file was modified since make started.
If you mark the file as precious, make will never delete the file
if interrupted.
Both can avoid deletion of intermediate files, but the difference is
the behavior when Make is interrupted; .SECONDARY deletes the target,
but .PRECIOUS does not.
The use of .PRECIOUS is relatively rare since we do not want to keep
partially constructed (possibly corrupted) targets.
Another difference is that .PRECIOUS works with pattern rules whereas
.SECONDARY does not.
.PRECIOUS: $(obj)/%.lex.c
works, but
.SECONDARY: $(obj)/%.lex.c
has no effect. However, for the reason above, I do not want to use
.PRECIOUS which could cause obscure build breakage.
The targets specified as .SECONDARY must be explicit. $(targets)
contains all targets that need to include .*.cmd files. So, the
intermediates you want to keep are mostly in there. Therefore, mark
$(targets) as .SECONDARY. It means primary targets are also marked
as .SECONDARY, but I do not see any drawback for this.
I replaced some .SECONDARY / .PRECIOUS markers with 'targets'. This
will make Kbuild search for non-existing .*.cmd files, but this is
not a noticeable performance issue.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Frank Rowand <frowand.list@gmail.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Using compatible strings without the <manufacturer> part for at24 is
deprecated since commit 6da28acf74 ("dt-bindings: at24: consistently
document the compatible property"). Use a correct 'atmel,<model>'
value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
It's very convenient to have fatal signals enabled on developemnt
platform as this allows to catch problems that happen early in
user-space (like crashing init or dynamic loader).
Otherwise we may either enable it later from alive taregt console
by "echo 1 > /proc/sys/kernel/print-fatal-signals" but:
1. We might be unfortunate enough to not reach working console
2. Forget to enable fatal signals and miss something interesting
Given we're talking about development platforms here it shouldn't
be a problem if a bit more data gets printed to debug console.
Moreover this makes behavior of all our dev platforms predictable
as today some platforms already have it enabled and some don't -
which is way too inconvenient.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Set initial core pll output frequency specified in device tree to
100MHz for SMP configuration and 90MHz for UP configuration.
It will be applied at the core pll driver probing.
Update platform quirk for decreasing core frequency for quad core
configuration.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Set initial core pll output frequency specified in device tree to
1GHz. It will be applied at the core pll driver probing.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
DW ethernet controller on axs10x hangs sometimes after SW reset.
Invoke the newly aded driver (reset-axs10x.c) by adding the DT bits.
With this in place, we don't need the open-coded quirk in platform
code, so get rid of it as well !
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With current SDIO CIU clock frequency (12500000Hz) DW MMC
controller fails to initialize some SD cards (which don't
support slow mode).
So increase SDIO CIU frequency from 12500000Hz to 50000000Hz by
switching from the default divisor value (div-by-8) to the
minimum possible value of the divisor (div-by-2) in HSDK platform
code.
Reported-by: Vineet Gupta <vgupta@synopsys.com>
Tested-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
DW ethernet controller on HSDK hangs sometimes after SW reset, so
add reset node to make possible to reset DW ethernet controller HW.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With corresponding clk driver now merged upstream, switch to it.
- core_clk now represent the PLL (vs. fixed clk before)
- input_clk represent the clk signal src for PLL (basically xtal)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
DW sdio controller has external ciu clock divider controlled
via register in SDIO IP. It divides sdio_ref_clk
(which comes from CGU) by 16 for default. So default mmcclk
clock (which comes to sdk_in) is 25000000 Hz.
So fix wrong current value (50000000 Hz) to actual 25000000 Hz.
Note this is a preventive fix, in line with similar change for HSDK
where this was actually needed. see:
http://lists.infradead.org/pipermail/linux-snps-arc/2017-September/002924.html
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
DW sdio controller has external ciu clock divider controlled via
register in SDIO IP. Due to its unexpected default value
(it should divide by 1 but it divides by 8)
SDIO IP uses wrong ciu clock and works unstable
So add temporary fix and change clock frequency from 100000000
to 12500000 Hz until we fix dw sdio driver itself.
Fixes SNPS STAR 9001204800
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- support for HSDK board hosting a Quad core HS38x4 based SoC running @ 1 GHz
(and some prerrquisite changes such as ability to scoot the kernel code/data
from start of memory map etc)
- Quite a few updates for EZChip (Mellanox) platform
- Fixes to fault/exception printing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=w8CJ
-----END PGP SIGNATURE-----
Merge tag 'arc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- Support for HSDK board hosting a Quad core HS38x4 based SoC running
@1GHz (and some prerrquisite changes such as ability to scoot the
kernel code/data from start of memory map etc)
- Quite a few updates for EZChip (Mellanox) platform
- Fixes to fault/exception printing
* tag 'arc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (26 commits)
ARC: Re-enable MMU upon Machine Check exception
ARC: Show fault information passed to show_kernel_fault_diag()
ARC: [plat-hsdk] initial port for HSDK board
ARC: mm: Decouple RAM base address from kernel link address
ARCv2: IOC: Tighten up the contraints (specifically base / size alignment)
ARC: [plat-axs103] refactor the DT fudging code
ARC: [plat-axs103] use clk driver #2: Add core pll node to DT to manage cpu clk
ARC: [plat-axs103] use clk driver #1: Get rid of platform specific cpu clk setting
ARCv2: SLC: provide a line based flush routine for debugging
ARC: Hardcode ARCH_DMA_MINALIGN to max line length we may have
ARC: [plat-eznps] handle extra aux regs #2: kernel/entry exit
ARC: [plat-eznps] handle extra aux regs #1: save/restore on context switch
ARC: [plat-eznps] avoid toggling of DPC register
ARC: [plat-eznps] Update the init sequence of aux regs per cpu.
ARC: [plat-eznps] new command line argument for HW scheduler at MTM
ARC: set boot print log level to PR_INFO
ARC: [plat-eznps] Handle user memory error same in simulation and silicon
ARC: [plat-eznps] use schd.wft instruction instead of sleep at idle task
ARC: create cpu specific version of arch_cpu_idle()
ARC: [plat-eznps] spinlock aware for MTM
...
This initial port adds support of ARC HS Development Kit board with some
basic features such serial port, USB, SD/MMC and Ethernet.
Essentially we run Linux kernel on all 4 cores (i.e. utilize SMP) and
heavily use IO Coherency for speeding-up DMA-aware peripherals.
Note as opposed to other ARC boards we link Linux kernel to
0x9000_0000 intentionally because cores 1 and 3 configured with DCCM
situated at our more usual link base 0x8000_0000. We still can use
memory region starting at 0x8000_0000 as we reallocate DCCM in our
platform code.
Note that PAE remapping for DMA clients does not work due to an RTL bug,
so CREG_PAE register must be programmed to all zeroes, otherwise it will
cause problems with DMA to/from peripherals even if PAE40 is not used.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[Needed for HSDK]
Currently the first page of system (hence RAM base) is assumed to be
@ CONFIG_LINUX_LINK_BASE, where kernel itself is linked.
However is case of HSDK platform, for reasons explained in that patch,
this is not true. kernel needs to be linked @ 0x9000_0000 while DDR
is still wired at 0x8000_0000. To properly account for this 256M of RAM,
we need to introduce a new option and base page frame accountiing off of
it.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: renamed CONFIG_KERNEL_RAM_BASE_ADDRESS => CONFIG_LINUX_RAM_BASE
: simplified changelog]
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Acked-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable 64bit adressing, where it needed, to make possible
enabling PAE40 on axs103.
This patch doesn't affect on any functionality.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev-HKixBCOQz3hWk0Htik3J/w@public.gmane.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Default clock frequency for ARC PGU does not match any
existing HDMI mode, instead the default value matches a
DVI mode. Change the clock frequency to 74.25MHz so that
it matches HDMI mode 1280x720@60Hz
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: devicetree@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch adds the necessary DT bindings to get HDMI audio
output in ARC AXS10x SDP. The bindings for I2S controller were
added as well as the bindings for simple audio card.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: devicetree@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
MotherBoard section has its "ranges" set to 0xE000_0000-0xF000_0000.
But UIO node maps 4 different areas in different memory locations
and all outside MB's ranges.
That obviously breaks UIO mappings in runtime.
Cc: Ruud Derwig <rderwig@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Trying to get clock for CPU cores on SMP systems I found that I was only
able to get clock for core[0]. That was because only one cpu@0 node was
represented in ARC HS device tree and it was impossible to get clock for
"non-existing" cores.
So as ARC HS may have up to 4 cores we update device tree to match
maximum possible cores quantity.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC CPU cores are driven by core_clk so we add corresponding "clocks"
property to ARC cpu nodes.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
No need for specifying a list of interrupts in the declaration
of IDU interrupt controller anymore since the kernel can obtain
a number of supported interrupts from the build register.
Also delete support of the second parameter for devices which
are connected to IDU because it is not used anywhere.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC VDK for EVSS uses UIO for communication with Embedded Vision
Subsystem.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1Hlx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"These are mostly timer/clocksource driver updates which were
Reviewed/Acked by Daniel but had to be merged via ARC tree due to
dependencies.
I will follow up with another pull request with actual ARC changes
early next week !
Summary:
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]"
* tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: axs10x: really enable ARC PGU
ARC: rename Zebu platform support to HAPS
clocksource: nps: avoid maybe-uninitialized warning
clocksource: Add clockevent support to NPS400 driver
clocksource: update "fn" at CLOCKSOURCE_OF_DECLARE() of nps400 timer
soc: Support for NPS HW scheduling
clocksource: import ARC timer driver
ARC: breakout timer include code into separate header ...
ARC: move mcip.h into include/soc and adjust the includes
ARC: breakout aux handling into a separate header
ARC: time: move time_init() out of the driver
ARC: timer: gfrc, rtc: build under same option (64-bit timers)
ARC: timer: gfrc, rtc: Read BCR to detect whether hardware exists ...
ARC: timer: gfrc, rtc: deuglify big endian code
Fairly routine update this time around with all changes specific to drivers.
o New driver for STMicroelectronics FDMA
o Memory-to-memory transfers on dw dmac
o Support for slave maps on pl08x devices
o Bunch of driver fixes to use dma_pool_zalloc
o Bunch of compile and warning fixes spread across drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pf0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Fairly routine update this time around with all changes specific to
drivers:
- New driver for STMicroelectronics FDMA
- Memory-to-memory transfers on dw dmac
- Support for slave maps on pl08x devices
- Bunch of driver fixes to use dma_pool_zalloc
- Bunch of compile and warning fixes spread across drivers"
[ The ST FDMA driver already came in earlier through the remoteproc tree ]
* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: sirf-dma: remove unused ‘sdesc’
dmaengine: pl330: remove unused ‘regs’
dmaengine: s3c24xx: remove unused ‘cdata’
dmaengine: stm32-dma: remove unused ‘src_addr’
dmaengine: stm32-dma: remove unused ‘dst_addr’
dmaengine: stm32-dma: remove unused ‘sfcr’
dmaengine: pch_dma: remove unused ‘cookie’
dmaengine: mic_x100_dma: remove unused ‘data’
dmaengine: img-mdc: remove unused ‘prev_phys’
dmaengine: usb-dmac: remove unused ‘uchan’
dmaengine: ioat: remove unused ‘res’
dmaengine: ioat: remove unused ‘ioat_dma’
dmaengine: ioat: remove unused ‘is_raid_device’
dmaengine: pl330: do not generate unaligned access
dmaengine: k3dma: move to dma_pool_zalloc
dmaengine: at_hdmac: move to dma_pool_zalloc
dmaengine: at_xdmac: don't restore unsaved status
dmaengine: ioat: set error code on failures
dmaengine: ioat: set error code on failures
dmaengine: DW DMAC: add multi-block property to device tree
...
Up until now we had ARC PGU not enabled in axs10x defconfigs trying
to not bloat kernel image again with yet another drivers and subsystems.
This change configures ARC PGU (as well as DRM bits it depends on)
to be built as a module and so those who need LCD screen to work on
axs10x may bundle built .ko files in their target's file-system with
help of the following command on host:
------------->8-------------
make INSTALL_MOD_PATH=_path_to_target_fs_ modules_install
------------->8-------------
and later on target with commands as simple as:
------------->8-------------
modprobe adv7511.ko
modprobe arcpgu.ko
------------->8-------------
get LCD working.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There are more ARC Linux HAPS users than Zebu ones.
Same kernel would work fine on both, even with embedded DT, assuming the FPGA
bitfile configuration is same
Suggested-by: Francois Bedard <fbedard@ynopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now when we have properly working performance counters in nSIM
even with interrupt support (fix should be a part of upcoming
nSIM engineering build 2016.12-005) we may enable perf support
by default for all platforms that use nSIM for ARC cores simulation.
Note 1: PCT node was missing for some reason in nsimosci.dts
while all other nSIM-related .dts files already had
PCT node for quite some time, so adding it now.
Note 2: All defconfigs were regenerated with "make savedefconfig"
which led to some clean-ups in nsimosci_hs_smp_defconfig:
CONFIG_FRAMEBUFFER_CONSOLE=y was removed because it is
automatically selected now by DRM.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The cool thing is that same kernel image can run on
- nsim OSCI simulation platform
- SDPlite FPGA setups
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
As it was discussed quite some time ago (see
https://lkml.org/lkml/2015/11/5/862) it's a good practice to add
"model" property in .dts. Moreover as per ePAPR "model" property is
required and should look like "manufacturer,model" so we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcHi9AAoJEHm+PkMAQRiGSJ0H/2o4t9VWYmhyPC1sdIHoCExJ
P4tBrcZYBmKcsOmIfnJDa5g/+IdhouEUM0v0fHPogS2UUWT9eRuJWYD3sY+HpEQ+
heKTli8X73gsFB25odeIbIt0jAoSiiMYWDrWqLNsuUV1tjEYVA8rH0SM94FiOC/5
7WVWXLTuH+Rm7JHP18BnKxmMMbzrTFmwisLMqFKyfZRRSlS+/ix7iLUNO9AFa39B
YHxNPihLrZ0oONyCOAQoHTIXXrw0cQbxV2utg3vnMcCZdme2xOn+iXMntTSKfZ39
iC9/T0vsO3R6OrRo2aDZAnCPUAniXnMEIhrKG37WMyXpj6cucZ/2QiNXcXviGV4=
=iLte
-----END PGP SIGNATURE-----
Back-merge tag 'v4.7-rc5' into drm-next
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in nSIM OSCI virtual platforms
with modern Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in HS38 VDK with modern
Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>