Some systems using mdio-gpio may use active-low gpio pins
(eg with inverters or FETs connected to all or some of the
gpio pins).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies error path and deinit/removal functions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang says:
====================
ipv4: fix flowi4_iif for input routing
This patchset fixes ->flowi4_iif for input routing and rp filter,
based on suggestion from Julian. See per patch for details.
v1 -> v2:
* merge the first two patches into one
* fix fib_check_nh() too
* add this cover letter
====================
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my special case, when a packet is redirected from veth0 to lo,
its skb->dev->ifindex would be LOOPBACK_IFINDEX. Meanwhile we
pass the hard-coded LOOPBACK_IFINDEX to fib_validate_source()
in ip_route_input_slow(). This would cause the following check
in fib_validate_source() fail:
(dev->ifindex != oif || !IN_DEV_TX_REDIRECTS(idev))
when rp_filter is disabeld on loopback. As suggested by Julian,
the caller should pass 0 here so that we will not end up by
calling __fib_validate_source().
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Julian:
Simply, flowi4_iif must not contain 0, it does not
look logical to ignore all ip rules with specified iif.
because in fib_rule_match() we do:
if (rule->iifindex && (rule->iifindex != fl->flowi_iif))
goto out;
flowi4_iif should be LOOPBACK_IFINDEX by default.
We need to move LOOPBACK_IFINDEX to include/net/flow.h:
1) It is mostly used by flowi_iif
2) Fix the following compile error if we use it in flow.h
by the patches latter:
In file included from include/linux/netfilter.h:277:0,
from include/net/netns/netfilter.h:5,
from include/net/net_namespace.h:21,
from include/linux/netdevice.h:43,
from include/linux/icmpv6.h:12,
from include/linux/ipv6.h:61,
from include/net/ipv6.h:16,
from include/linux/sunrpc/clnt.h:27,
from include/linux/nfs_fs.h:30,
from init/do_mounts.c:32:
include/net/flow.h: In function ‘flowi4_init_output’:
include/net/flow.h:84:32: error: ‘LOOPBACK_IFINDEX’ undeclared (first use in this function)
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4 driver is triggering schedules while atomic inside
mlx4_en_netpoll:
spin_lock_irqsave(&cq->lock, flags);
napi_synchronize(&cq->napi);
^^^^^ msleep here
mlx4_en_process_rx_cq(dev, cq, 0);
spin_unlock_irqrestore(&cq->lock, flags);
This was part of a patch by Alexander Guller from Mellanox in 2011,
but it still isn't upstream.
Signed-off-by: Chris Mason <clm@fb.com>
cc: stable@vger.kernel.org
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Petazzoni says:
====================
net: mvneta: fix usage as a module, and support QSGMII properly
This set of patches is a new attempt at fixing the operation of the
mvneta driver when built as a module. For the record, the previous
attempt, merged in commit e3a8786c10
('net: mvneta: fix usage as a module on RGMII configurations') caused
problems for all RGMII configurations.
In fact, it turned out that the MAC to PHY connection on the Armada XP
GP, which was described as using RGMII-ID according to its Device
Tree, is in fact a QSGMII connection. And the RGMII and QSGMII
configurations have to be handled in a different way in the driver,
because the SERDES configuration is different in those two cases.
So, this patch series fixes that by:
* Adding minimal handling of a "qsgmii" connection type in the PHY
layer. Mainly to make sure that a "qsgmii" phy-mode in the Device
Tree is recognized, and handed over to the driver as
PHY_INTERFACE_QSGMII.
* Changing the mvneta driver to properly configure the RGMIIEn and
PCSEn bits in the GMAC_CTRL_2 register, and configure the SERDES
register, in the three possible cases: RGMII, SGMII and QSGMII.
* Updating the Device Tree of the Armada XP GP board to reflect the
fact that it uses a QSGMII MAC/PHY connection.
PATCH 1 and 2 would be merged by David Miller, through the net tree,
while PATCH 3 would be merged by the mach-mvebu maintainers, through
their tree and arm-soc.
This set of patches has been tested on:
* Armada XP GP (four QSGMII interfaces)
* Armada XP DB (two RGMII interfaces and two SGMII interfaces)
* Armada 370 Mirabox (two RGMII interfaces)
I've tested both the driver built-in, and compiled as a module.
Since the last attempt at fixing this was quite a fiasco, I'd like
this new attempt to be tested more widely before being applied. I'll
try to do some testing on other Armada boards I have, but independent
testing from other persons would also be appreciated.
Note that these patches apply after reverting the previous attempt,
obviously.
====================
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, some other platforms, namely the Armada XP GP don't use
SGMII, but a QSGMII connection between the MAC and the PHY, and this
case was not supported by the mvneta driver, which was relying on
configuration put in place by the bootloader. While this works when
the mvneta driver is built-in (because clocks are not gated), it
breaks when mvneta is built as a module, because the clock is gated
(all configuration is lost) and then re-enabled when the mvneta driver
is loaded.
In order to support all of RGMII, SGMII and QSGMII, this commit
reworks how the PHY interface configuration is done, and simplifies
it: it removes the mvneta_port_sgmii_config() and
mvneta_gmac_rgmii_set() functions, which were strange because
mvneta_gmac_rgmii_set() was called in all cases, even for SGMII
configurations. Also, the mvneta_gmac_rgmii_set() function was taking
a boolean as argument, which was always true.
Instead, all the PHY interface configuration logic is moved into the
mvneta_port_power_up() function, in a much simpler 'switch' construct,
with four cases:
- QSGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured in QSGMII. Technically speaking,
configuring the SERDES of the first port would be sufficient, but
it is simpler to do it on all ports.
- SGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured as SGMII.
- RGMII: the RGMIIEn bit in GMAC_CTRL_2 is set. The PCSEn bit is kept
cleared, and no SERDES configuration is done, because RGMII is not
using SERDES lanes.
- other: an error is returned. For this reason, the
mvneta_port_power_up() now returns an int instead of nothing, and
the return value is checked by mvneta_probe().
This has been successfully tested on:
* Armada XP DB, which has two RGMII and two SGMII connections
* Armada XP GP, which uses QSGMII for its four interfaces
* Armada 370 Mirabox, which has two RGMII connections
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the necessary definitions for the PHY layer to
recognize "qsgmii" as a valid PHY interface. A QSMII interface, as
defined at
http://en.wikipedia.org/wiki/Media_Independent_Interface#Quad_Serial_Gigabit_Media_Independent_Interface,
is "is a method of combining four SGMII lines into a 5Gbit/s
interface. QSGMII, like SGMII, uses LVDS signalling for the TX and RX
data and a single LVDS clock signal. QSGMII uses significantly fewer
signal lines than four SGMII busses."
This type of MAC <-> PHY connection might require special handling on
the MAC driver side, so it should be possible to express this type of
MAC <-> PHY connection, for example in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCDI command times out (whether or not we find it
completed when we poll), call efx_mcdi_abandon(), which tells
all subsequent MCDI calls to fail-fast, and queues up an FLR.
Because an FLR doesn't lead to receiving any reboot even from
the MC (unlike most other types of reset), we have to call
efx_ef10_reset_mc_allocations.
In efx_start_all(), if a reset (of any kind) is pending, we
bail out.
Without this, attempts to reconfigure (e.g. change mtu) can
cause driver/mc state inconsistency if the first MCDI call
triggers an FLR.
For similar reasons, on EF10, in
efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number
of active queues to zero before calling efx_stop_all().
And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT),
set active_queues and flushes pending & outstanding to zero.
efx_mcdi_mode_{poll,event}() should not take us out of fail-fast
mode. Instead, this is done by efx_mcdi_reset() after the FLR
completes.
The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really
fit into the hierarchy of reset 'scopes' whereby efx_reset()
decides some resets subsume others. Thus, it uses separate logic.
Also, fixed up some inconsistency around RESET_TYPE_MC_BIST,
which was in the wrong place in that hierarchy.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix BPF filter validation of netlink attribute accesses, from
Mathias Kruase.
2) Netfilter conntrack generation seqcount not initialized properly,
from Andrey Vagin.
3) Fix comparison mask computation on big-endian in nft_cmp_fast(),
from Patrick McHardy.
4) Properly limit MTU over ipv6, from Eric Dumazet.
5) Fix seccomp system call argument population on 32-bit, from Daniel
Borkmann.
6) skb_network_protocol() should not use hard-coded ETH_HLEN, instead
skb->mac_len needs to be used. From Vlad Yasevich.
7) We have several cases of using socket based communications to
implement a tunnel. For example, some tunnels are encapsulations
over UDP so we use an internal kernel UDP socket to do the
transmits.
These tunnels should behave just like other software devices and
pass the packets on down to the next layer.
Most importantly we want the top-level socket (eg TCP) that created
the traffic to be charged for the SKB memory.
However, once you get into the IP output path, we have code that
assumed that whatever was attached to skb->sk is an IP socket.
To keep the top-level socket being charged for the SKB memory,
whilst satisfying the needs of the IP output path, we now pass in an
explicit 'sk' argument.
From Eric Dumazet.
8) ping_init_sock() leaks group info, from Xiaoming Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
cxgb4: use the correct max size for firmware flash
qlcnic: Fix MSI-X initialization code
ip6_gre: don't allow to remove the fb_tunnel_dev
ipv4: add a sock pointer to dst->output() path.
ipv4: add a sock pointer to ip_queue_xmit()
driver/net: cosa driver uses udelay incorrectly
at86rf230: fix __at86rf230_read_subreg function
at86rf230: remove check if AVDD settled
net: cadence: Add architecture dependencies
net: Start with correct mac_len in skb_network_protocol
Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
cxgb4: Save the correct mac addr for hw-loopback connections in the L2T
net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
seccomp: fix populating a0-a5 syscall args in 32-bit x86 BPF
qlcnic: Do not disable SR-IOV when VFs are assigned to VMs
qlcnic: Fix QLogic application/driver interface for virtual NIC configuration
qlcnic: Fix PVID configuration on eSwitch port.
qlcnic: Fix max ring count calculation
qlcnic: Fix to send INIT_NIC_FUNC as first mailbox.
qlcnic: Fix panic due to uninitialzed delayed_work struct in use.
...
The wrong max fw size was being used and causing false
"too big" errors running ethtool -f.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qlcnic_setup_tss_rss_intr() might enter endless
loop in case pci_enable_msix() contiguously returns a
positive number of MSI-Xs that could have been allocated.
Besides, the function contains 'err = -EIO;' assignment
that never could be reached. This update fixes the
aforementioned issues.
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to remove the FB tunnel with the command 'ip link del ip6gre0' but
this is unsafe, the module always supposes that this device exists. For example,
ip6gre_tunnel_lookup() may use it unconditionally.
Let's add a rtnl handler for dellink, which will never remove the FB tunnel (we
let ip6gre_destroy_tunnels() do the job).
Introduced by commit c12b395a46 ("gre: Support GRE over IPv6").
CC: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.
The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.
Fixes: 8f646c922d ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d5956 ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.
One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.
Fixes: 31c70d5956 ("l2tp: keep original skb ownership")
Reported-by: Zhan Jianyu <nasa4836@gmail.com>
Tested-by: Zhan Jianyu <nasa4836@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cosa driver, udelay with more than 20000 may cause __bad_udelay.
Use msleep for instead.
Signed-off-by: Li, Zhen-Hua <zhen-hual@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __at86rf230_read_subreg function don't mask and shift register
contents which it should do. This patch adds the necessary masks and
shift operations in this function.
Since we have csma support this can make some trouble on state changes.
Since CSMA support turned on some bits in the TRX_STATUS register that
used to be zero, not masking broke checking of the TRX_STATUS field
after commanding a state change.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVDD regulator is only enabled when the RF section is active TX_ON
(PLL_ON) state. Since commit 7dcbd22a97
("ieee802154: ensure that first RF212 state comes from TRX_OFF").
We are in TRX_OFF state at the time at86rf230_hw_init is run.
Note that this test would only fail in case of a severe hardware
malfunction (faulty/shorted power supply, etc.) so it wasn't all that
useful in the first place.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cadence ethernet chipsets are only used on specific ARM
architectures. Add Kconfig dependencies so that drivers for these
chipsets are only buildable on the relevant architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull KVM fixes from Marcelo Tosatti:
- Fix for guest triggerable BUG_ON (CVE-2014-0155)
- CR4.SMAP support
- Spurious WARN_ON() fix
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: remove WARN_ON from get_kernel_ns()
KVM: Rename variable smep to cr4_smep
KVM: expose SMAP feature to guest
KVM: Disable SMAP for guests in EPT realmode and EPT unpaging mode
KVM: Add SMAP support when setting CR4
KVM: Remove SMAP bit from CR4_RESERVED_BITS
KVM: ioapic: try to recover if pending_eoi goes out of range
KVM: ioapic: fix assignment of ioapic->rtc_status.pending_eoi (CVE-2014-0155)
Pull bmc2835 crypto fix from Herbert Xu:
"This fixes a potential boot crash on bcm2835 due to the recent change
that now causes hardware RNGs to be accessed on registration"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm2835 - fix oops when rng h/w is accessed during registration
smp_read_barrier_depends() can be used if there is data dependency between
the readers - i.e. if the read operation after the barrier uses address
that was obtained from the read operation before the barrier.
In this file, there is only control dependency, no data dependecy, so the
use of smp_read_barrier_depends() is incorrect. The code could fail in the
following way:
* the cpu predicts that idx < entries is true and starts executing the
body of the for loop
* the cpu fetches map->extent[0].first and map->extent[0].count
* the cpu fetches map->nr_extents
* the cpu verifies that idx < extents is true, so it commits the
instructions in the body of the for loop
The problem is that in this scenario, the cpu read map->extent[0].first
and map->nr_extents in the wrong order. We need a full read memory barrier
to prevent it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains three Netfilter fixes for your net tree,
they are:
* Fix missing generation sequence initialization which results in a splat
if lockdep is enabled, it was introduced in the recent works to improve
nf_conntrack scalability, from Andrey Vagin.
* Don't flush the GRE keymap list in nf_conntrack when the pptp helper is
disabled otherwise this crashes due to a double release, from Andrey
Vagin.
* Fix nf_tables cmp fast in big endian, from Patrick McHardy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, when the packet arrives at skb_mac_gso_segment()
its skb->mac_len already accounts for some of the mac lenght
headers in the packet. This seems to happen when forwarding
through and OpenSSL tunnel.
When we start looking for any vlan headers in skb_network_protocol()
we seem to ignore any of the already known mac headers and start
with an ETH_HLEN. This results in an incorrect offset, dropped
TSO frames and general slowness of the connection.
We can start counting from the known skb->mac_len
and return at least that much if all mac level headers
are known and accounted for.
Fixes: 53d6471cef (net: Account for all vlan headers in skb_mac_gso_segment)
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Daniel Borkman <dborkman@redhat.com>
Tested-by: Martin Filip <nexus+kernel@smoula.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename variable smep to cr4_smep, which can better reflect the
meaning of the variable.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
SMAP is disabled if CPU is in non-paging mode in hardware.
However KVM always uses paging mode to emulate guest non-paging
mode with TDP. To emulate this behavior, SMAP needs to be
manually disabled when guest switches to non-paging mode.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds SMAP handling logic when setting CR4 for guests
Thanks a lot to Paolo Bonzini for his suggestion to use the branchless
way to detect SMAP violation.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Hardware needs the local device mac address to support hw loopback for
rdma loopback connections.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing seccomp code, we found that BPF_S_ANC_SECCOMP_LD_W has
been wrongly decoded by commit a8fc927780 ("sk-filter: Add ability to
get socket filter program (v2)") into the opcode BPF_LD|BPF_B|BPF_ABS
although it should have been decoded as BPF_LD|BPF_W|BPF_ABS.
In practice, this should not have much side-effect though, as such
conversion is/was being done through prctl(2) PR_SET_SECCOMP. Reverse
operation PR_GET_SECCOMP will only return the current seccomp mode, but
not the filter itself. Since the transition to the new BPF infrastructure,
it's also not used anymore, so we can simply remove this as it's
unreachable.
Fixes: a8fc927780 ("sk-filter: Add ability to get socket filter program (v2)")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus reports that on 32-bit x86 Chromium throws the following seccomp
resp. audit log messages:
audit: type=1326 audit(1397359304.356:28108): auid=500 uid=500
gid=500 ses=2 subj=unconfined_u:unconfined_r:chrome_sandbox_t:s0-s0:c0.c1023
pid=3677 comm="chrome" exe="/opt/google/chrome/chrome" sig=0
syscall=172 compat=0 ip=0xb2dd9852 code=0x30000
audit: type=1326 audit(1397359304.356:28109): auid=500 uid=500
gid=500 ses=2 subj=unconfined_u:unconfined_r:chrome_sandbox_t:s0-s0:c0.c1023
pid=3677 comm="chrome" exe="/opt/google/chrome/chrome" sig=0 syscall=5
compat=0 ip=0xb2dd9852 code=0x50000
These audit messages are being triggered via audit_seccomp() through
__secure_computing() in seccomp mode (BPF) filter with seccomp return
codes 0x30000 (== SECCOMP_RET_TRAP) and 0x50000 (== SECCOMP_RET_ERRNO)
during filter runtime. Moreover, Linus reports that x86_64 Chromium
seems fine.
The underlying issue that explains this is that the implementation of
populate_seccomp_data() is wrong. Our seccomp data structure sd that
is being shared with user ABI is:
struct seccomp_data {
int nr;
__u32 arch;
__u64 instruction_pointer;
__u64 args[6];
};
Therefore, a simple cast to 'unsigned long *' for storing the value of
the syscall argument via syscall_get_arguments() is just wrong as on
32-bit x86 (or any other 32bit arch), it would result in storing a0-a5
at wrong offsets in args[] member, and thus i) could leak stack memory
to user space and ii) tampers with the logic of seccomp BPF programs
that read out and check for syscall arguments:
syscall_get_arguments(task, regs, 0, 1, (unsigned long *) &sd->args[0]);
Tested on 32-bit x86 with Google Chrome, unfortunately only via remote
test machine through slow ssh X forwarding, but it fixes the issue on
my side. So fix it up by storing args in type correct variables, gcc
is clever and optimizes the copy away in other cases, e.g. x86_64.
Fixes: bd4cf0ed33 ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Reported-and-bisected-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh says:
====================
qlcnic: Bug fixes
This patch series contains following bug fixes -
* Send INIT_NIC_FUNC mailbox command as first mailbox
* Fix a panic because of uninitialized delayed_work.
* Fix inconsistent calculation of max rings count.
* Fix PVID configuration issue. Driver needs to clear older
PVID before adding new one.
* Fix QLogic application/driver interface by packing vNIC information
array.
* Fix a crash when user tries to disable SR-IOV while VFs are
still assigned to VMs.
Please apply to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o While disabling SR-IOV when VFs are assigned to VMs causes host crash
so return -EPERM when user request to disable SR-IOV using pci sysfs in
case of VFs are assigned to VMs.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Application expect vNIC number as the array index but driver interface
return configuration in array index form.
o Pack the vNIC information array in the buffer such that application can
access it using vNIC number as the array index.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear older PVID before adding a newer PVID to the eSwicth port
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not read max rings count from qlcnic_get_nic_info(). Use driver defined
values for 82xx adapters. In case of 83xx adapters, use minimum of firmware
provided and driver defined values.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o INIT_NIC_FUNC should be first mailbox sent. Sending DCB capability and
parameter query commands after that command.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o AEN event was being received before initializing delayed_work struct
and handlers for it. This was resulting in crash. This patch fixes it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla says:
====================
be2net: patch set
Patch 1/2 is a v2 of a patch that was submitted earlier (as a part of a
different patch-set). v2 incorporates a suggestion given by David Laight
for how long to poll for pending TX completions while disabling a device.
Patch 2/2 fixes a crash in be_remove()->be_close()
path after be2net has aborted an EEH error recovery
due to a permanant failure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the EEH error recovery path, when a permanent failure occurs,
we clean up adapter structure (i.e. destroy queues etc) by calling
be_clear() and return PCI_ERS_RESULT_DISCONNECT.
After this the stack tries to remove device from bus and calls
be_remove() which invokes netdev_unregister()->be_close().
be_close() operating on destroyed queues results in a
NULL dereference.
This patch fixes this problem by introducing a flag to keep track
of the setup state.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_close() currently waits for a max of 200ms to receive all pending
TX compls. This timeout value was roughly calculated based on 10G
transmission speeds and the TX queue depth. This timeout may not be
enough when the link is operating at lower speeds or in multi-channel/SR-IOV
configs with TX-rate limiting setting.
It is hard to calculate a "proper timeout value" that works in all
configurations. This patch solves this problem by continuing to reap
TX completions till the HW is completely silent for a period of 10ms or
a HW error is detected.
v2: implements the new scheme (as suggested by David Laight) instead of
just waiting longer than 200ms for reaping all completions.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix in commit [1] is not sufficient since a deferred VF initialization
could happen after pci_enable_sriov() is finished, but before the PF is
fully initialized.
Need to prevent VFs from initializing till the PF is fully ready and
comm channel is operational.
[1] - 9798935 "net/mlx4_core: mlx4_init_slave() shouldn't access comm
channel before PF is ready"
CC: Stuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP isn't enabled, bnx2_suspend/resume are unused; don't
build them when they aren't used.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Francois reported that setting big mtu on loopback device could prevent
tcp sessions making progress.
We do not support (yet ?) IPv6 Jumbograms and cook corrupted packets.
We must limit the IPv6 MTU to (65535 + 40) bytes in theory.
Tested:
ifconfig lo mtu 70000
netperf -H ::1
Before patch : Throughput : 0.05 Mbits
After patch : Throughput : 35484 Mbits
Reported-by: Francois WELLENREITER <f.wellenreiter@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
nft_cmp_fast is used for equality comparisions of size <= 4. For
comparisions of size < 4 byte a mask is calculated that is applied to
both the data from userspace (during initialization) and the register
value (during runtime). Both values are stored using (in effect) memcpy
to a memory area that is then interpreted as u32 by nft_cmp_fast.
This works fine on little endian since smaller types have the same base
address, however on big endian this is not true and the smaller types
are interpreted as a big number with trailing zero bytes.
The mask therefore must not include the lower bytes, but the higher bytes
on big endian. Add a helper function that does a cpu_to_le32 to switch
the bytes on big endian. Since we're dealing with a mask of just consequitive
bits, this works out fine.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Guenter Roeck
David S. Miller
Cong Wang
Chris Mason
Thomas Petazzoni
Edward Cree
Linus Torvalds
Steve Wise
Alexander Gordeev
Nicolas Dichtel
Eric Dumazet
Li, Zhen-Hua
Alexander Aring
Jean Delvare
Mikulas Patocka
Vlad Yasevich
Marcelo Tosatti
Feng Wu
Daniel Borkmann
Manish Chopra
Jitendra Kalsaria
Shahed Shaikh
Sucheta Chakraborty
Kalesh AP
Vasundhara Volam
Amir Vadai
Daniel J Blueman
Patrick McHardy
Andrey Vagin