Add support for IPMI 0.9 systems to the IPMI driver. Just handle a shorter
get device ID command with less information.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Stian Jordet <liste@jordet.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The removal of proc entries was done holding a lock, which is no longer
allowed. There is no need for the lock, only a mutex is required, so switch
over to a mutex.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert over to the new NMI handling for getting IPMI watchdog timeouts via an
NMI. This add config options to know if there is the ability to receive NMIs
and if it has an NMI post processing call. Then it modifies the IPMI watchdog
to take advantage of this so that it can know if an NMI comes in.
It also adds testing that the IPMI NMI watchdog works.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the IPMI watchdog timer sets the watchdog timeout on a panic, but it
doesn't actually poll the interface to make sure the message goes out.
Add an interface for polling the IPMI driver, and add code to the IPMI
watchdog timer to poll the interface when the timer is set from a panic.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lockdep was giving an error when loading the IPMI watchdog module. It turns
out that if you try to claim a lock in a parameter handling routine, lockdep
won't see that lock as "static" yet because the module is not yet on the
module list, so it will complain.
However, the semaphore in question is completely unnecessary. So just remove
it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patrick found a race at startup. Interrupts were being enabled for the IPMI
interface before the driver was really ready to handle them. This could
result in an oops if something was pending on the interface at startup and
interrupt were already enabled (technically shouldn't happen, but need to
cover for this in real life). So move the IRQ setup to the code that starts
the actual IPMI processing.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get rid of sparse related warnings from places that use integer as NULL
pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
if (controller && !request_region) then we leaked a tty driver struct, fix it
by adding function deinit tail with goto-ing into it (and from other fail
paths too)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We may use pdev->revision instead of reading pci config space directly, so
remove pci_read_config_dword invoking.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- register_device unconditionally (non-pci dependent) to have also isa
devices in /dev
- unregister devices on module removal
- don't set TTY_DRIVER_DYNAMIC_DEV twice (removed the one dependent on some
macro)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rocket, switch sleep_on to completion
- sleep_on is deprecated and racy, use completion instead
- also check retval of interruptible function and return ERESTARTSYS
eventually
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
prepend moxa_ to all moxa functions which laxes this
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- use dev_* where pdev is available (probe function)
- add some printks on fail paths
- add KERN_ macros otherwise
- remove useless verbose variable
- wrap lines to 80 cols at most
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC drivers/char/cyclades.o
drivers/char/cyclades.c: In function 'cy_init':
drivers/char/cyclades.c:5488: warning: label 'err_unr' defined but not used
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of them are signedness, the rest unused function parameters.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lock whole processing in isr, avoid error-prone locking/unlocking in rx/tx
esp. On fail paths (there was a bug in the past yet).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to large indent the code was wrapped and unreadable. Create 3 function
instead of one and reorder the code, so it is readable now.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The work done in bottom half doesn't cost much cpu time (e.g. tty_hangup
itself schedules its own bottom half), it's possible to do the work in isr
directly and save hence some .text.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
moxa, fix and optimise empty timer
don't wait and delete empty timer in empty timer function. Also fire next
empty timer at rounded jiffies to save power.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/mxser.c:386: warning: 'mxser_get_PCI_conf' declared 'static' but never defined
when building without CONFIG_PCI.
[jesper.juhl@gmail.com: Fix warning: 'CheckIsMoxaMust' defined but not used]
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is years dead code and it keeps turning up in confusing ways when
grepping for stuff.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mxser_new, remove useless comments in mxser_cards
It was rest from times, where info about the card was separated (name,
ports number and flags).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mxser_new, upgrade to 1.10
This adds support for new (5 cards) hardware.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of having a bunch of ifdefs in sysctl.c move all of the pty sysctl
logic into drivers/char/pty.c
As well as cleaning up the logic this prevents sysctl_check_table from
complaining that the root table has a NULL data pointer on something with
generic methods.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the definition of 'struct pm_ops' and related functions from <linux/pm.h>
to <linux/suspend.h> .
There are, at least, the following reasons to do that:
* 'struct pm_ops' is specifically related to suspend and not to the power
management in general.
* As long as 'struct pm_ops' is defined in <linux/pm.h>, any modification of it
causes the entire kernel to be recompiled, which is unnecessary and annoying.
* Some suspend-related features are already defined in <linux/suspend.h>, so it
is logical to move the definition of 'struct pm_ops' into there.
* 'struct hibernation_ops', being the hibernation-related counterpart of
'struct pm_ops', is defined in <linux/suspend.h> .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tty_termios_encode_baud_rate() function as defined by tty_ioctl.c has a
problem with the baud_table within. The comparison operators are reversed
and as a result this table's entries never match and BOTHER is always used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since default_utf8 is already a sysfs attribute, having an extra
CONFIG_VT_UNICODE compile-time option is redundant, since sysfs attributes can
be set at boot and run time.
Also let Linux VCs default to UTF-8 (as per the discussion at
http://lkml.org/lkml/2007/9/6/99).
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Cc: Bill Nottingham <notting@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create an inline function for clflush(), with the proper arguments,
and use it instead of hard-coding the instruction.
This also removes one instance of hard-coded wbinvd, based on a patch
by Bauder de Oliveira Costa.
[ tglx: arch/x86 adaptation ]
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'xen-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xfs: eagerly remove vmap mappings to avoid upsetting Xen
xen: add some debug output for failed multicalls
xen: fix incorrect vcpu_register_vcpu_info hypercall argument
xen: ask the hypervisor how much space it needs reserved
xen: lock pte pages while pinning/unpinning
xen: deal with stale cr3 values when unpinning pagetables
xen: add batch completion callbacks
xen: yield to IPI target if necessary
Clean up duplicate includes in arch/i386/xen/
remove dead code in pgtable_cache_init
paravirt: clean up lazy mode handling
paravirt: refactor struct paravirt_ops into smaller pv_*_ops
Remove NULL initializers and clean whitespace a bit.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes hvc_init() to be called only when someone actually uses the
hvc_console driver. Dave Jones complained when profiling bootup.
hvc_console used to only be for Power aka pSeries: now lguest and Xen both
want it built-in in case the kernel is a guest under one of those, even
though usually it will be a native boot.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds three new functions (or in one case to be more exact makes it
always available)
tty_termios_copy_hw
Copies all the hardware settings from one termios structure to the other.
This is intended for drivers that support little or no hardware setting
tty_termios_encode_baud_rate
Allows you to set the input and output baud rate in a termios structure. A
driver is supposed to set the resulting baud rate from a request so most
will want to use this function to set the resulting input and output rates
to match the hardware values. Internally it knows about keeping Bxxx
encoding when possible to maximise compatibility.
tty_encode_baud_rate
As above but for the tty's own current termios structure
I suspect this will initially need some tweaking as it gets enabled by
driver patches over the next few mm cycles so consider this lot -mm only
for the moment so it can stabilize and end up neat before it goes to base.
I've tried not to break any obscure architectures - if you get a speed you
can't represent the code will print warnings on non updated termios systems
but not break.
Once this is merged and seems sane I've got a growing pile of driver
updates to use it - notably for USB serial drivers.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As of now, the kernel defaults to non-unicode and XLATE for the keyboard.
We've been changing this in Fedora, but that requires patching the defaults
in the kernel.
The attached introduces CONFIG_VT_UNICODE, which sets the console in
unicode mode by default on boot, including both the virtual terminal and
the keyboard driver.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Coverity checker spotted that we'd have already oops'ed if "tty"
was NULL.
Since "tty" can't be NULL when we reach this line of code this patch
removes the NULL check.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We simply define it to the same value. Nowdays the TTY flip value is
irrelevant but the value it used is as good as any so why risk breaking it
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There have been issues with non-latin1 diacritics and unicode.
http://bugzilla.kernel.org/show_bug.cgi?id=7746
Git 759448f459 `Kernel utf-8 handling'
partly resolved it by adding conversion between diacritics and
unicode. The patch below goes further by just turning diacritics into
unicode, hence providing better future support. The kbd support can be
fetched from
http://bugzilla.kernel.org/attachment.cgi?id=12313
This was tested in all of latin1, latin9, latin2 and unicode with french
and czech dead keys.
Turn the kernel accent_table into unicode, and extend ioctls KDGKBDIACR
and KDSKBDIACR into their equivalents KDGKBDIACRUC and KDSKBDIACR.
New function int conv_uni_to_8bit(u32 uni) for converting unicode into 8bit
_input_. No, we don't want to store the translation, as it is potentially
sparse and large.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jan Engelhardt <jengelh@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver does
proc_mkdir("ipmi", NULL);
but
remove_proc_entry(proc_ipmi_root->name, &proc_root);
This is OK and working if only slightly inconsistent. Also changing
proc_root to NULL will help OpenVZ which has multiple proc roots and, as we
now know, requires matching parents in such cases.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we discover the TIS TPM device via PNP, use the PNP IRQ information rather
than probing for an IRQ. If PNP shows no IRQ, run the TPM in polling mode.
Tested-by: <valdis.kletnieks@vt.edu>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Kylene Hall <kjhall@us.ibm.com>
Cc: <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds
Corey Minyard
Corey Minyard
Stephen Hemminger
Joe Perches
Jiri Slaby
Jesper Juhl
Alan Cox
Eric W. Biederman
Rafael J. Wysocki
Maciej W. Rozycki
Jan Engelhardt
Wim Van Sebroeck
H. Peter Anvin
Jeff Garzik
Pavel Machek
Rusty Russell
Bill Nottingham
Adrian Bunk
Samuel Thibault
Alexey Dobriyan
Bjorn Helgaas
Mariusz Kozlowski