This patch bumps the release of the r6040 driver. There has been
quite some versions of it out there, but this one is the one
people should report bugs against.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch allows the MAC to handle the RX FIFO full
and no descriptor available interrupts. While we are at it
replace the TX interrupt with its corresponding definition.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the default waiting time of a packet, which
along with our previous r6040_rx path, was causing huge delays
with another host (160 to 230 ms).
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Define all the descriptor status the MAC can set.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch completely reworks the RX path in order to be
more accurate about what is going on with the MAC.
We no longer read the error from the MLSR register instead read
the descriptor status register which reflects, the error per descriptor.
We now allocate skbs on the fly in r6040_rx, and we handle allocation
failure instead of simply dropping the packet. Remove the
rx_free_desc counter of r6040_private structure since we
allocate skbs in the RX path.
r6040_rx_buf_alloc is now removed and becomes unuseless.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We did not call napi_disabled when putting down the interface
which should be done. Finally initialize lp->dev when everything
is set.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Joseph Fannin <jfannin@gmail.com> and Takashi Iwai <tiwai@suse.de>
noticed that commit 073a345c04
("mv643xx_eth: clarify irq masking and unmasking") broke the
mv643xx_eth build when NETPOLL is enabled, due to it not renaming
one instance of INT_CAUSE_EXT in mv643xx_eth_netpoll(). This patch
takes care of that instance as well.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Joseph Fannin <jfannin@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rework the RX buffers allocation function so that we do not
leak memory in the case we could not allocate skbs for the
RX path. Propagate the errors to the r6040_up function
where we call the RX buffers allocation function.
Also rename the r6040_alloc_txbufs function to
r6040_init_txbufs, to reflect what it really does.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a helper function which only modifies R6040 MAC registers
use it when we timeout, and on adapter initialization. Fix
the scheduling while atomic but in the timeout routine due
to the reallocation of rx/tx buffers.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a null pointer access in r6040_rx due
to lp->dev not being initialized.
Fix the TX timeouts, TX irq was not re-enabled on RX irq
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prefix all functions inside the r6040 driver with r6040 to
avoid namespace clashing.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch allows Windows Mobile 6 devices to be used for
tethering -- that is, used as modems. It was requested by
AdamW in kernel bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=11119
and Mandriva kernel-discuss list. It is tested and confirmed
to work by Peterl:
http://forum.eeeuser.com/viewtopic.php?pid=323543#p323543
This patch is based on the patch in the above kernel bugzilla,
which is from the usb-rndis-lite tree.
[ dbrownell@users.sourceforge.net: misc fixes ]
Signed-off-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using multiple cores in the same package to handle received traffic
does not appear to provide a performance benefit. Therefore use CPU
topology information to count CPU packages and use that as the default
number of RX queues and interrupts. We rely on interrupt balancing to
spread the interrupts across packages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This avoids deadlock in case a reset is triggered during self-test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As recommended by Jean Delvare:
- Increase timeout to 50 ms
- Leave adapter class clear so that unwanted drivers do not probe our bus
- Use strlcpy() for name initialisation
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes e1000 driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed. This is based on the
ioport-free patch of e1000 driver from Auke Kok and Tomohiro Kusumi.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher<jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The email linux-nics@intel.com is no longer available, remove all
references.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Redefine DPRINTK macro using do while(0)
__FUNCTION__ to __func__
structs {} on separate lines
Surround negative constants with ()
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use struct e1000_hw *hw = adapter->hw; where necessary
Change macros E1000_READ_REG and E1000_WRITE_REG to er32 and ew32
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
An | in an if statement to check a bit? I think this needs to be a &.
As a result of this typo meth will always operate in promiscuous mode.
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Full patch for the Atheros L1E Gigabit Ethernet driver.
Supportring AR8121, AR8113 and AR8114
Signed-off-by: Jie Yang <jie.yang @atheros.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support. Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware. This patch is necessary for 2.6.24, 2.6.25 and 2.6.26
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The OQO model 2 has an RTL8139 from Atheros that doesn't like MMIO.
It fails on modprobe, with a 'PCI Bus error' message.
Force it to always use polled IO.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is needed to support devices that only work with PIO without
penalising devices that work fine with MMIO in distro kernels.
It also allows us to eventually use PIO as a fallback when setting
up MMIO fails.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MII_M1111_HWCFG_FIBER_COPPER_RES is a bit of MII_M1111_PHY_EXT_SR, not
MII_M1111_PHY_EXT_CR.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/igb/igb_main.c:388:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove magic numbers for items that we already have
defined in the register header file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change driver version to 4.0.0. Netxen firmwares as old as
v3.4.216 are supported.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NX3031 supports cut-through operation where ingress packets are
directly dma'ed into host buffers to reduce latency.
This requires larger dma buffers (2kb) and different alignemnt.
The buffer posting logic is changed a bit. The free rx buffers
are maintained in linked list, since the received reference
handles can be out of order. However rx descriptors are still
posted sequentially, indexed by producer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAC addr, multicast filters, mtu are set through firmware commands
in firmware v4.0.0+ because of virtualization of physical ports.
Link status is also read from registers allocated by firmware for
each virtual port.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Contains rx and tx ring context management and certain
firmware commands for netxen firmware v4.0.0+.
This patch gathers all HW context management code into
netxen_nic_ctx.c.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It had only couple of functions which are moved to main.c
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add initialization code in pci probe for new chip and retain
compatibility with old revisions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New revision of netxen chip has 2MB PCI memory. Older chips
had 128MB addressable PCI memory. To retain compatibility,
this patch adds function pointers based on pci bar0 size.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add macros for new chip revision and board configurations.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable multicast address filtering capabilities in the hardware.
Upto 16 multicast addresses can be programmed for each physical
port. Support "allmulti" mode, if enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Reduce access to global arrays in data path.
o Remove duplicate/unused variables, unecessary alignment constraints.
o Use correct pci_dev instead of fallback device for consistent
allocations.
o Disable ethtool set_eeprom functionality for now, it was only used
for flashing firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Florian Fainelli
Lennert Buytenhek
Thomas Backlund
Paulius Zaleckas
Ben Hutchings
Taku Izumi
Francois Romieu
Jeff Kirsher
Joe Perches
Christoph Lameter
Jie Yang
Jesse Brandeburg
Dave Jones
Wang Jian
Harvey Harrison
Ben Dooks
Ursula Braun
Peter Tiedemann
Andy Richter
Dhananjay Phadke