Channels/sub-channels can be affinitized to VCPUs in the guest. Implement
this affinity in a way that is NUMA aware. The current protocol distributed
the primary channels uniformly across all available CPUs. The new protocol
is NUMA aware: primary channels are distributed across the available NUMA
nodes while the sub-channels within a primary channel are distributed amongst
CPUs within the NUMA node assigned to the primary channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Map target_cpu to target_vcpu using the mapping table.
We should use the mapping table to transform guest CPU ID to VP Index
as is done for the non-performance critical channels.
While the value CPU 0 is special and will
map to VP index 0, it is good to be consistent.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory notifiers are being executed in a sequential order and when one of
them fails returning something different from NOTIFY_OK the remainder of
the notification chain is not being executed. When a memory block is being
onlined in online_pages() we do memory_notify(MEM_GOING_ONLINE, ) and if
one of the notifiers in the chain fails we end up doing
memory_notify(MEM_CANCEL_ONLINE, ) so it is possible for a notifier to see
MEM_CANCEL_ONLINE without seeing the corresponding MEM_GOING_ONLINE event.
E.g. when CONFIG_KASAN is enabled the kasan_mem_notifier() is being used
to prevent memory hotplug, it returns NOTIFY_BAD for all MEM_GOING_ONLINE
events. As kasan_mem_notifier() comes before the hv_memory_notifier() in
the notification chain we don't see the MEM_GOING_ONLINE event and we do
not take the ha_region_mutex. We, however, see the MEM_CANCEL_ONLINE event
and unconditionally try to release the lock, the following is observed:
[ 110.850927] =====================================
[ 110.850927] [ BUG: bad unlock balance detected! ]
[ 110.850927] 4.1.0-rc3_bugxxxxxxx_test_xxxx #595 Not tainted
[ 110.850927] -------------------------------------
[ 110.850927] systemd-udevd/920 is trying to release lock
(&dm_device.ha_region_mutex) at:
[ 110.850927] [<ffffffff81acda0e>] mutex_unlock+0xe/0x10
[ 110.850927] but there are no more locks to release!
At the same time we can have the ha_region_mutex taken when we get the
MEM_CANCEL_ONLINE event in case one of the memory notifiers after the
hv_memory_notifier() in the notification chain failed so we need to add
the mutex_is_locked() check. In case of MEM_ONLINE we are always supposed
to have the mutex locked.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Windows 10.
Signed-off-by: Keith Mange <keith.mange@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Primary channels are distributed evenly across all vcpus we have. When the host
asks us to create subchannels it usually makes us num_cpus-1 offers and we are
supposed to distribute the work evenly among the channel itself and all its
subchannels. Make sure they are all assigned to different vcpus.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to call init_vp_index() after we added the channel to the appropriate
list (global or subchannel) to be able to use this information when assigning
the channel to the particular vcpu. To do so we need to move a couple of
functions around. The only real change is the init_vp_index() call. This is a
small refactoring without a functional change.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is unlikely that that host will ask us to close only one subchannel for a
device but let's be consistent. Do both num_sc++ and num_sc-- with
channel->lock to be on the safe side.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case there was an error reported in the response to the CHANNELMSG_OPENCHANNEL
call we need to do the cleanup as a vmbus_open() user won't be doing it after
receiving an error. The cleanup should be done on all failure paths. We also need
to avoid returning open_info->response.open_result.status as the return value as
all other errors we return from vmbus_open() are -EXXX and vmbus_open() callers
are not supposed to analyze host error codes.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the protocol for tearing down the monitor state established with
the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
free_channel() has been invoked in
vmbus_remove() -> hv_process_channel_removal(), or vmbus_remove() ->
... -> vmbus_close_internal() -> hv_process_channel_removal().
We also change to use list_for_each_entry_safe(), because the entry
is removed in hv_process_channel_removal().
This patch fixes a bug in the vmbus unload path.
Thank Dan Carpenter for finding the issue!
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case we do request_resource() in vmbus_acpi_add() we need to tear it down
to be able to load the driver again. Otherwise the following crash in observed
when hv_vmbus unload/load sequence is performed on a Generation2 instance:
[ 38.165701] BUG: unable to handle kernel paging request at ffffffffa00075a0
[ 38.166315] IP: [<ffffffff8107dc5f>] __request_resource+0x2f/0x50
[ 38.166315] PGD 1f34067 PUD 1f35063 PMD 3f723067 PTE 0
[ 38.166315] Oops: 0000 [#1] SMP
[ 38.166315] Modules linked in: hv_vmbus(+) [last unloaded: hv_vmbus]
[ 38.166315] CPU: 0 PID: 267 Comm: modprobe Not tainted 3.19.0-rc5_bug923184+ #486
[ 38.166315] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v1.0 11/26/2012
[ 38.166315] task: ffff88003f401cb0 ti: ffff88003f60c000 task.ti: ffff88003f60c000
[ 38.166315] RIP: 0010:[<ffffffff8107dc5f>] [<ffffffff8107dc5f>] __request_resource+0x2f/0x50
[ 38.166315] RSP: 0018:ffff88003f60fb58 EFLAGS: 00010286
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify driver registration reporting and move it to debug level as normally daemons write to syslog themselves
and these kernel messages are useless.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce FCOPY_VERSION_1 to support kernel replying to the negotiation
message with its own version.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce VSS_OP_REGISTER1 to support kernel replying to the negotiation
message with its own version.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to hv_utils_transport to support both netlink and /dev/vmbus/hv_kvp communication methods.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify the code with the recently introduced hv_utils_transport. Netlink
communication is disabled for fcopy.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert to hv_utils_transport to support both netlink and /dev/vmbus/hv_vss communication methods.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intention is to make KVP/VSS drivers work through misc char devices.
Introduce an abstraction for kernel/userspace communication to make the
migration smoother. Transport operational mode (netlink or char device)
is determined by the first received message. To support driver upgrades
the switch from netlink to chardev operational mode is supported.
Every hv_util daemon is supposed to register 2 callbacks:
1) on_msg() to get notified when the userspace daemon sent a message;
2) on_reset() to get notified when the userspace daemon drops the connection.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get an additional reference otherwise a crash is observed when hv_utils module is being unloaded while
fcopy daemon is still running. .owner gives us an additional reference when
someone holds a descriptor for the device.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to using the hvutil_device_state state machine from using 3 different state variables:
fcopy_transaction.active, opened, and in_hand_shake.
State transitions are:
-> HVUTIL_DEVICE_INIT when driver loads or on device release
-> HVUTIL_READY if the handshake was successful
-> HVUTIL_HOSTMSG_RECEIVED when there is a non-negotiation message from the host
-> HVUTIL_USERSPACE_REQ after userspace daemon read the message
-> HVUTIL_USERSPACE_RECV after/if userspace has replied
-> HVUTIL_READY after we respond to the host
-> HVUTIL_DEVICE_DYING on driver unload
In hv_fcopy_onchannelcallback() process ICMSGTYPE_NEGOTIATE messages even when
the userspace daemon is disconnected, otherwise we can make the host think
we don't support FCOPY and disable the service completely.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to using the hvutil_device_state state machine from using kvp_transaction.active.
State transitions are:
-> HVUTIL_DEVICE_INIT when driver loads or on device release
-> HVUTIL_READY if the handshake was successful
-> HVUTIL_HOSTMSG_RECEIVED when there is a non-negotiation message from the host
-> HVUTIL_USERSPACE_REQ after we sent the message to the userspace daemon
-> HVUTIL_USERSPACE_RECV after/if the userspace daemon has replied
-> HVUTIL_READY after we respond to the host
-> HVUTIL_DEVICE_DYING on driver unload
In hv_vss_onchannelcallback() process ICMSGTYPE_NEGOTIATE messages even when
the userspace daemon is disconnected, otherwise we can make the host think
we don't support VSS and disable the service completely.
Unfortunately there is no good way we can figure out that the userspace daemon
has died (unless we start treating all timeouts as such), add a protection
against processing new VSS_OP_REGISTER messages while being in the middle of a
transaction (HVUTIL_USERSPACE_REQ or HVUTIL_USERSPACE_RECV state).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to using the hvutil_device_state state machine from using 2 different state variables: kvp_transaction.active and
in_hand_shake.
State transitions are:
-> HVUTIL_DEVICE_INIT when driver loads or on device release
-> HVUTIL_READY if the handshake was successful
-> HVUTIL_HOSTMSG_RECEIVED when there is a non-negotiation message from the host
-> HVUTIL_USERSPACE_REQ after we sent the message to the userspace daemon
-> HVUTIL_USERSPACE_RECV after/if the userspace daemon has replied
-> HVUTIL_READY after we respond to the host
-> HVUTIL_DEVICE_DYING on driver unload
In hv_kvp_onchannelcallback() process ICMSGTYPE_NEGOTIATE messages even when
the userspace daemon is disconnected, otherwise we can make the host think
we don't support KVP and disable the service completely.
Unfortunately there is no good way we can figure out that the userspace daemon
has died (unless we start treating all timeouts as such). In case the daemon
restarts we skip the negotiation procedure (so the daemon is supposed to has
the same version). This behavior is unchanged from in_handshake approach.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVP/VSS/FCOPY drivers work in fully serialized mode: we wait till userspace
daemon registers, wait for a message from the host, send this message to the
daemon, get the reply, send it back to host, wait for another message.
Introduce enum hvutil_device_state to represend this state in all 3 drivers.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'fcopy_work' (and fcopy_work_func) is a misnomer as it sounds like we expect
this useful work to happen and in reality it is just an emergency escape when
timeout happens.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'kvp_work' (and kvp_work_func) is a misnomer as it sounds like we expect
this useful work to happen and in reality it is just an emergency escape when
timeout happens.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In theory, the host is not supposed to issue any requests before be reply to
the previous one. In KVP we, however, support the following scenarios:
1) A message was received before userspace daemon registered;
2) A message was received while the previous one is still being processed.
In VSS we support only the former. Add support for the later, use
hv_poll_channel() to do the job.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In theory, the host is not supposed to issue any requests before be reply to
the previous one. In KVP we, however, support the following scenarios:
1) A message was received before userspace daemon registered;
2) A message was received while the previous one is still being processed.
In FCOPY we support only the former. Add support for the later, use
hv_poll_channel() to do the job.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move poll_channel() to hyperv_vmbus.h and make it inline and rename it to hv_poll_channel() so it can be reused
in other hv_util modules.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We set kvp_context when we want to postpone receiving a packet from vmbus due
to the previous transaction being unfinished. We, however, never reset this
state, all consequent kvp_respond_to_host() calls will result in poll_channel()
calling hv_kvp_onchannelcallback(). This doesn't cause real issues as:
1) Host is supposed to serialize transactions as well
2) If no message is pending vmbus_recvpacket() will return 0 recvlen.
This is just a cleanup.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These declarations are internal to hv_util module and hv_fcopy_* declarations
already reside there.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
balloon_wrk.num_pages is __u32 and it comes from host in struct dm_balloon
where it is also __u32. We, however, use 'int' in balloon_up() and in case
we happen to receive num_pages>INT_MAX request we'll end up allocating zero
pages as 'num_pages < alloc_unit' check in alloc_balloon_pages() will pass.
Change num_pages type to unsigned int.
In real life ballooning request come with num_pages in [512, 32768] range so
this is more a future-proof/cleanup.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'Drivers: hv: hv_balloon: refuse to balloon below the floor' fix does not
correctly handle the case when val.freeram < num_pages as val.freeram is
__kernel_ulong_t and the 'val.freeram - num_pages' value will be a huge
positive value instead of being negative.
Usually host doesn't ask us to balloon more than val.freeram but in case
he have a memory hog started after we post the last pressure report we
can get into troubles.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the retries can be done within a millisecond successfully, so we
sleep 1ms before the first retry, then gradually increase the retry
interval to 2^n with max value of 2048ms. Doing so, we will have shorter
overall delay time, because most of the cases succeed within 1-2 attempts.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... and simplify alloc_balloon_pages() interface by removing redundant
alloc_error from it.
If we happen to enter balloon_up() with balloon_wrk.num_pages = 0 we will enter
infinite 'while (!done)' loop as alloc_balloon_pages() will be always returning
0 and not setting alloc_error. We will also be sending a meaningless message to
the host on every iteration.
The 'alloc_unit == 1 && alloc_error -> num_ballooned == 0' change and
alloc_error elimination requires a special comment. We do alloc_balloon_pages()
with 2 different alloc_unit values and there are 4 different
alloc_balloon_pages() results, let's check them all.
alloc_unit = 512:
1) num_ballooned = 0, alloc_error = 0: we do 'alloc_unit=1' and retry pre- and
post-patch.
2) num_ballooned > 0, alloc_error = 0: we check 'num_ballooned == num_pages'
and act accordingly, pre- and post-patch.
3) num_ballooned > 0, alloc_error > 0: we report this chunk and remain within
the loop, no changes here.
4) num_ballooned = 0, alloc_error > 0: we do 'alloc_unit=1' and retry pre- and
post-patch.
alloc_unit = 1:
1) num_ballooned = 0, alloc_error = 0: this can happen in two cases: when we
passed 'num_pages=0' to alloc_balloon_pages() or when there was no space in
bl_resp to place a single response. The second option is not possible as
bl_resp is of PAGE_SIZE size and single response 'union dm_mem_page_range' is
8 bytes, but the first one is (in theory, I think that Hyper-V host never
places such requests). Pre-patch code loops forever, post-patch code sends
a reply with more_pages = 0 and finishes.
2) num_ballooned > 0, alloc_error = 0: we ran out of space in bl_resp, we
report partial success and remain within the loop, no changes pre- and
post-patch.
3) num_ballooned > 0, alloc_error > 0: pre-patch code finishes, post-patch code
does one more try and if there is no progress (we finish with
'num_ballooned = 0') we finish. So we try a bit harder with this patch.
4) num_ballooned = 0, alloc_error > 0: both pre- and post-patch code enter
'more_pages = 0' branch and finish.
So this patch has two real effects:
1) We reply with an empty response to 'num_pages=0' request.
2) We try a bit harder on alloc_unit=1 allocations (and reply with an empty
tail reply in case we fail).
An empty reply should be supported by host as we were able to send it even with
pre-patch code when we were not able to allocate a single page.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 79208c57da ("Drivers: hv: hv_balloon: Make adjustments in computing
the floor") was inacurate as it introduced a jump in our piecewiese linear
'floor' function:
At 2048MB we have:
Left limit:
104 + 2048/8 = 360
Right limit:
256 + 2048/16 = 384 (so the right value is 232)
We now have to make an adjustment at 8192 boundary:
232 + 8192/16 = 744
512 + 8192/32 = 768 (so the right value is 488)
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we add memory in 128Mb blocks but the request from host can be
aligned differently. In such case we add a partially backed block and
when this block goes online we skip onlining pages which are not backed
(hv_online_page() callback serves this purpose). When we receive next
request for the same host add region we online pages which were not backed
before with hv_bring_pgs_online(). However, we don't check if the the block
in question was onlined and online this tail unconditionally. This is bad as
we avoid all online_pages() logic: these pages are not accounted, we don't
send notifications (and hv_balloon is not the only receiver of them),...
And, first of all, nobody asked as to online these pages. Solve the issue by
checking if the last previously backed page was onlined and onlining the tail
only in case it was.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not necessary any longer, since we can safely run the blocking
message handlers in vmbus_connection.work_queue now.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the 2 fucntions can safely run in vmbus_connection.work_queue without
hang, we don't need to schedule new work items into the per-channel workqueue.
Actally we can even remove the per-channel workqueue now -- we'll do it
in the next patch.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A work item in vmbus_connection.work_queue can sleep, waiting for a new
host message (usually it is some kind of "completion" message). Currently
the new message will be handled in the same workqueue, but since work items
in the workqueue is serialized, we actually have no chance to handle
the new message if the current work item is sleeping -- as as result, the
current work item will hang forever.
K. Y. has posted the below fix to resolve the issue:
Drivers: hv: vmbus: Perform device register in the per-channel work element
Actually we can simplify the fix by directly running non-blocking message
handlers in the dispatch tasklet (inspired by K. Y.).
This patch is the fundamental change. The following 2 patches will simplify
the message offering and rescind-offering handling a lot.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't wait after sending request for offers to the host. This wait is
unnecessary and simply adds 5 seconds to the boot time.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle the case when the write to the ringbuffer fails. In this case,
unconditionally signal the host. Since we may have deferred signalling
the host based on the kick_q parameter, signalling the host
unconditionally in this case deals with the issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export the vmbus_sendpacket_pagebuffer_ctl() interface. This export will be
used by the netvsc driver.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a channel has been rescinded, the close operation is a noop.
Restructure the code so we deal with the rescind condition after
we properly cleanup the channel. I would like to thank
Dexuan Cui <decui@microsoft.com> for observing this problem.
The current code leaks memory when the channel is rescinded.
The current char-next branch is broken and this patch fixes
the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The indenting makes it clear that there were curly braces intended here.
Fixes: 2dd37cb815 ('Drivers: hv: vmbus: Handle both rescind and offer messages in the same context')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HV_CRASH_CTL_CRASH_NOTIFY is a 64 bit number. Depending on the usage context,
the value may be truncated. This patch is in response from the following
email from Wu Fengguang <fengguang.wu@intel.com>:
From: Wu Fengguang <fengguang.wu@intel.com>
Subject: [char-misc:char-misc-testing 25/45] drivers/hv/vmbus_drv.c:67:9: sparse:
constant 0x8000000000000000 is so big it is unsigned long
tree: git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git char-misc-testing
head: b3de8e3719
commit: 96c1d0581d [25/45] Drivers: hv: vmbus: Add support for VMBus panic notifier handler
reproduce:
# apt-get install sparse
git checkout 96c1d0581d
make ARCH=x86_64 allmodconfig
make C=1 CF=-D__CHECK_ENDIAN__
sparse warnings: (new ones prefixed by >>)
drivers/hv/vmbus_drv.c:67:9: sparse: constant 0x8000000000000000 is so big it is unsigned long
...
Signed-off-by: Nick Meier <nmeier@microsoft.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory blocks can be onlined in random order. When this order is not natural
some memory pages are not onlined because of the redundant check in
hv_online_page().
Here is a real world scenario:
1) Host tries to hot-add the following (process_hot_add):
pg_start=rg_start=0x48000, pfn_cnt=111616, rg_size=262144
2) This results in adding 4 memory blocks:
[ 109.057866] init_memory_mapping: [mem 0x48000000-0x4fffffff]
[ 114.102698] init_memory_mapping: [mem 0x50000000-0x57ffffff]
[ 119.168039] init_memory_mapping: [mem 0x58000000-0x5fffffff]
[ 124.233053] init_memory_mapping: [mem 0x60000000-0x67ffffff]
The last one is incomplete but we have special has->covered_end_pfn counter to
avoid onlining non-backed frames and hv_bring_pgs_online() function to bring
them online later on.
3) Now we have 4 offline memory blocks: /sys/devices/system/memory/memory9-12
$ for f in /sys/devices/system/memory/memory*/state; do echo $f `cat $f`; done | grep -v onlin
/sys/devices/system/memory/memory10/state offline
/sys/devices/system/memory/memory11/state offline
/sys/devices/system/memory/memory12/state offline
/sys/devices/system/memory/memory9/state offline
4) We bring them online in non-natural order:
$grep MemTotal /proc/meminfo
MemTotal: 966348 kB
$echo online > /sys/devices/system/memory/memory12/state && grep MemTotal /proc/meminfo
MemTotal: 1019596 kB
$echo online > /sys/devices/system/memory/memory11/state && grep MemTotal /proc/meminfo
MemTotal: 1150668 kB
$echo online > /sys/devices/system/memory/memory9/state && grep MemTotal /proc/meminfo
MemTotal: 1150668 kB
As you can see memory9 block gives us zero additional memory. We can also
observe a huge discrepancy between host- and guest-reported memory sizes.
The root cause of the issue is the redundant pg >= covered_start_pfn check (and
covered_start_pfn advancing) in hv_online_page(). When upper memory block in
being onlined before the lower one (memory12 and memory11 in the above case) we
advance the covered_start_pfn pointer and all memory9 pages do not pass the
check. If the assumption that host always gives us requests in sequential order
and pg_start always equals rg_start when the first request for the new HA
region is received (that's the case in my testing) is correct than we can get
rid of covered_start_pfn and pg >= start_pfn check in hv_online_page() is
sufficient.
The current char-next branch is broken and this patch fixes
the bug.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When add_memory() fails the following BUG is observed:
[ 743.646107] hv_balloon: hot_add memory failed error is -17
[ 743.679973]
[ 743.680930] =====================================
[ 743.680930] [ BUG: bad unlock balance detected! ]
[ 743.680930] 3.19.0-rc5_bug1131426+ #552 Not tainted
[ 743.680930] -------------------------------------
[ 743.680930] kworker/0:2/255 is trying to release lock (&dm_device.ha_region_mutex) at:
[ 743.680930] [<ffffffff81aae5fe>] mutex_unlock+0xe/0x10
[ 743.680930] but there are no more locks to release!
This happens as we don't acquire ha_region_mutex and hot_add_req() expects us
to as it does unconditional mutex_unlock(). Acquire the lock on the error path.
The current char-next branch is broken and this patch fixes
the bug.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is a continuation of the rescind handling cleanup work. We cannot
block in the global message handling work context especially if we are blocking
waiting for the host to wake us up. I would like to thank
Dexuan Cui <decui@microsoft.com> for observing this problem.
The current char-next branch is broken and this patch fixes
the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/hv/vmbus_drv.c:51:5: sparse: symbol 'hyperv_panic_event' was not declared. Should it be static?
drivers/hv/vmbus_drv.c:51:5: sparse: symbol 'hyperv_panic_event' was not declared. Should it be static?
drivers/hv/vmbus_drv.c:51:5: sparse: symbol 'hyperv_panic_event' was not declared. Should it be static?
drivers/hv/vmbus_drv.c:51:5: sparse: symbol 'hyperv_panic_event' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement an API that gives additional control on the what VMBUS flags will be
set as well as if the host needs to be signalled. This API will be
useful for clients that want to batch up requests to the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement an API for sending pagebuffers that gives more control to the client
in terms of setting the vmbus flags as well as deciding when to
notify the host. This will be useful for enabling batch processing.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current algorithm for picking an outgoing channel was not distributing
the load well. Implement a simple round-robin scheme to ensure good
distribution of the outgoing traffic.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hyper-V allows a guest to notify the Hyper-V host that a panic
condition occured. This notification can include up to five 64
bit values. These 64 bit values are written into crash MSRs.
Once the data has been written into the crash MSRs, the host is
then notified by writing into a Crash Control MSR. On the Hyper-V
host, the panic notification data is captured in the Windows Event
log as a 18590 event.
Crash MSRs are defined in appendix H of the Hypervisor Top Level
Functional Specification. At the time of this patch, v4.0 is the
current functional spec. The URL for the v4.0 document is:
http://download.microsoft.com/download/A/B/4/AB43A34E-BDD0-4FA6-BDEF-79EEF16E880B/Hypervisor Top Level Functional Specification v4.0.docx
Signed-off-by: Nick Meier <nmeier@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When host asks us to balloon up we need to be sure we're not committing suicide
by overballooning. Use already existent 'floor' metric as our lowest possible
value for free ram.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When hot-added memory pages are not brought online or when some memory blocks
are sent offline the subsequent ballooning process kills the guest with OOM
killer. This happens as we don't report these pages as neither used nor free
and apparently host algorithm considers them as being unused. Keep track of
all online/offline operations and report all currently offline pages as being
used so host won't try to balloon them out.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When many memory regions are being added and automatically onlined the
following lockup is sometimes observed:
INFO: task udevd:1872 blocked for more than 120 seconds.
...
Call Trace:
[<ffffffff816ec0bc>] schedule_timeout+0x22c/0x350
[<ffffffff816eb98f>] wait_for_common+0x10f/0x160
[<ffffffff81067650>] ? default_wake_function+0x0/0x20
[<ffffffff816eb9fd>] wait_for_completion+0x1d/0x20
[<ffffffff8144cb9c>] hv_memory_notifier+0xdc/0x120
[<ffffffff816f298c>] notifier_call_chain+0x4c/0x70
...
When several memory blocks are going online simultaneously we got several
hv_memory_notifier() trying to acquire the ha_region_mutex. When this mutex is
being held by hot_add_req() all these competing acquire_region_mutex() do
mutex_trylock, fail, and queue themselves into wait_for_completion(..). However
when we do complete() from release_region_mutex() only one of them wakes up.
This could be solved by changing complete() -> complete_all() memory onlining
can be delayed as well, in that case we can still get several
hv_memory_notifier() runners at the same time trying to grab the mutex.
Only one of them will succeed and the others will hang for forever as
complete() is not being called. We don't see this issue often because we have
5sec onlining timeout in hv_mem_hot_add() and usually all udev events arrive
in this time frame.
Get rid of the trylock path, waiting on the mutex is supposed to provide the
required serialization.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we log messages when either we are not able to map an ID to a
channel or when the channel does not have a callback associated
(in the channel interrupt handling path). These messages don't add
any value, get rid of them.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the offer is rescinded, vmbus_close() can free up the channel;
deinitialize the service before closing the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly rollback state in vmbus_pocess_offer() in the failure paths.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Execute both ressind and offer messages in the same work context. This serializes these
operations and naturally addresses the various corner cases.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In response to a rescind message, we need to remove the channel and the
corresponding device. Cleanup this code path by factoring out the code
to remove a channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle the case when the device may be removed when the device has no driver
attached to it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NetworkDirect is a service that supports guest RDMA.
Define the GUID for this service.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correctly rollback state if the failure occurs after we have handed over
the ownership of the buffer to the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch changes the type of t from int to unsigned long.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch changes the type of t from int to unsigned long.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
return type of wait_for_completion_timeout is unsigned long not int, this
patch changes the type of t from int to unsigned long.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch, the state is put to CHANNEL_OPENING_STATE, and when
the driver is loaded next time, vmbus_open() will fail immediately due to
newchannel->state != CHANNEL_OPEN_STATE.
CC: "K. Y. Srinivasan" <kys@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got HV_STATUS_INVALID_CONNECTION_ID on Hyper-V 2008 R2 when keeping running
"rmmod hv_netvsc; modprobe hv_netvsc; rmmod hv_utils; modprobe hv_utils"
in a Linux guest. Looks the host has some kind of throttling mechanism if
some kinds of hypercalls are sent too frequently.
Without the patch, the driver can occasionally fail to load.
Also let's retry HV_STATUS_INSUFFICIENT_MEMORY, though we didn't get it
before.
Removed 'case -ENOMEM', since the hypervisor doesn't return this.
CC: "K. Y. Srinivasan" <kys@microsoft.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the line vmbus_open() returns, srv->util_cb can be already running
and the variables, like util_fw_version, are needed by the srv->util_cb.
So we have to make sure the variables are initialized before the vmbus_open().
CC: "K. Y. Srinivasan" <kys@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newly introduced clockevent devices made it impossible to unload hv_vmbus
module as clockevents_config_and_register() takes additional reverence to
the module. To make it possible again we do the following:
- avoid setting dev->owner for clockevent devices;
- implement hv_synic_clockevents_cleanup() doing clockevents_unbind_device();
- call it from vmbus_exit().
In theory hv_synic_clockevents_cleanup() can be merged with hv_synic_cleanup(),
however, we call hv_synic_cleanup() from smp_call_function_single() and this
doesn't work for clockevents_unbind_device() as it does such call on its own. I
opted for a separate function.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SynIC has to be switched off when we unload the module, otherwise registered
memory pages can get corrupted after (as Hyper-V host still writes there) and
we see the following crashes for random processes:
[ 89.116774] BUG: Bad page map in process sh pte:4989c716 pmd:36f81067
[ 89.159454] addr:0000000000437000 vm_flags:00000875 anon_vma: (null) mapping:ffff88007bba55a0 index:37
[ 89.226146] vma->vm_ops->fault: filemap_fault+0x0/0x410
[ 89.257776] vma->vm_file->f_op->mmap: generic_file_mmap+0x0/0x60
[ 89.297570] CPU: 0 PID: 215 Comm: sh Tainted: G B 3.19.0-rc5_bug923184+ #488
[ 89.353738] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS 090006 05/23/2012
[ 89.409138] 0000000000000000 000000004e083d7b ffff880036e9fa18 ffffffff81a68d31
[ 89.468724] 0000000000000000 0000000000437000 ffff880036e9fa68 ffffffff811a1e3a
[ 89.519233] 000000004989c716 0000000000000037 ffffea0001edc340 0000000000437000
[ 89.575751] Call Trace:
[ 89.591060] [<ffffffff81a68d31>] dump_stack+0x45/0x57
[ 89.625164] [<ffffffff811a1e3a>] print_bad_pte+0x1aa/0x250
[ 89.667234] [<ffffffff811a2c95>] vm_normal_page+0x55/0xa0
[ 89.703818] [<ffffffff811a3105>] unmap_page_range+0x425/0x8a0
[ 89.737982] [<ffffffff811a3601>] unmap_single_vma+0x81/0xf0
[ 89.780385] [<ffffffff81184320>] ? lru_deactivate_fn+0x190/0x190
[ 89.820130] [<ffffffff811a4131>] unmap_vmas+0x51/0xa0
[ 89.860168] [<ffffffff811ad12c>] exit_mmap+0xac/0x1a0
[ 89.890588] [<ffffffff810763c3>] mmput+0x63/0x100
[ 89.919205] [<ffffffff811eba48>] flush_old_exec+0x3f8/0x8b0
[ 89.962135] [<ffffffff8123b5bb>] load_elf_binary+0x32b/0x1260
[ 89.998581] [<ffffffff811a14f2>] ? get_user_pages+0x52/0x60
hv_synic_cleanup() function exists but noone calls it now. Do the following:
- call hv_synic_cleanup() on each cpu from vmbus_exit();
- write global disable bit through MSR;
- use hv_synic_free_cpu() to avoid memory leask and code duplication.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to destroy hv_vmbus_con on module shutdown, otherwise the following
crash is sometimes observed:
[ 76.569845] hv_vmbus: Hyper-V Host Build:9600-6.3-17-0.17039; Vmbus version:3.0
[ 82.598859] BUG: unable to handle kernel paging request at ffffffffa0003480
[ 82.599287] IP: [<ffffffffa0003480>] 0xffffffffa0003480
[ 82.599287] PGD 1f34067 PUD 1f35063 PMD 3f72d067 PTE 0
[ 82.599287] Oops: 0010 [#1] SMP
[ 82.599287] Modules linked in: [last unloaded: hv_vmbus]
[ 82.599287] CPU: 0 PID: 26 Comm: kworker/0:1 Not tainted 3.19.0-rc5_bug923184+ #488
[ 82.599287] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v1.0 11/26/2012
[ 82.599287] Workqueue: hv_vmbus_con 0xffffffffa0003480
[ 82.599287] task: ffff88007b6ddfa0 ti: ffff88007f8f8000 task.ti: ffff88007f8f8000
[ 82.599287] RIP: 0010:[<ffffffffa0003480>] [<ffffffffa0003480>] 0xffffffffa0003480
[ 82.599287] RSP: 0018:ffff88007f8fbe00 EFLAGS: 00010202
...
To avoid memory leaks we need to free monitor_pages and int_page for
vmbus_connection. Implement vmbus_disconnect() function by separating cleanup
path from vmbus_connect().
As we use hv_vmbus_con to release channels (see free_channel() in channel_mgmt.c)
we need to make sure the work was done before we remove the queue, do that with
drain_workqueue(). We also need to avoid handling messages which can (potentially)
create new channels, so set vmbus_connection.conn_state = DISCONNECTED at the very
beginning of vmbus_exit() and check for that in vmbus_onmessage_work().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On driver shutdown device_obj is being freed twice:
1) In vmbus_free_channels()
2) vmbus_device_release() (which is being triggered by device_unregister() in
vmbus_device_unregister().
This double kfree leads to the following sporadic crash on driver unload:
[ 23.469876] general protection fault: 0000 [#1] SMP
[ 23.470036] Modules linked in: hv_vmbus(-)
[ 23.470036] CPU: 2 PID: 213 Comm: rmmod Not tainted 3.19.0-rc5_bug923184+ #488
[ 23.470036] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS 090006 05/23/2012
[ 23.470036] task: ffff880036ef1cb0 ti: ffff880036ce8000 task.ti: ffff880036ce8000
[ 23.470036] RIP: 0010:[<ffffffff811d2e1b>] [<ffffffff811d2e1b>] __kmalloc_node_track_caller+0xdb/0x1e0
[ 23.470036] RSP: 0018:ffff880036cebcc8 EFLAGS: 00010246
...
When this crash does not happen on driver unload the similar one is expected if
we try to load hv_vmbus again.
Remove kfree from vmbus_free_channels() as freeing it from
vmbus_device_release() seems right.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All channel work queues are named 'hv_vmbus_ctl', this makes them
indistinguishable in ps output and makes it hard to link to the corresponding
vmbus device. Rename them to hv_vmbus_ctl/N and make vmbus device names match,
e.g. now vmbus_1 device is served by hv_vmbus_ctl/1 work queue.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an SMP Hyper-V guest is running on top of 2012R2 Server and secondary
cpus are sent offline (with echo 0 > /sys/devices/system/cpu/cpu$cpu/online)
the system freeze is observed. This happens due to the fact that on newer
hypervisors (Win8, WS2012R2, ...) vmbus channel handlers are distributed
across all cpus (see init_vp_index() function in drivers/hv/channel_mgmt.c)
and on cpu offlining nobody reassigns them to CPU0. Prevent cpu offlining
when vmbus is loaded until the issue is fixed host-side.
This patch also disables hibernation but it is OK as it is also broken (MCE
error is hit on resume). Suspend still works.
Tested with WS2008R2 and WS2012R2.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver update for 3.20-rc1.
Lots of little things in here, all described in the changelog. Nothing
major or unusual, except maybe the binder selinux stuff, which was all
acked by the proper selinux people and they thought it best to come
through this tree.
All of this has been in linux-next with no reported issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgs80ACgkQMUfUDdst+yn86gCeMLbxANGExVLd+PR46GNsAUQb
SJ4AmgIqrkIz+5LCwZWM02ldbYhPeBVf
=lfmM
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc patches from Greg KH:
"Here's the big char/misc driver update for 3.20-rc1.
Lots of little things in here, all described in the changelog.
Nothing major or unusual, except maybe the binder selinux stuff, which
was all acked by the proper selinux people and they thought it best to
come through this tree.
All of this has been in linux-next with no reported issues for a while"
* tag 'char-misc-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
coresight: fix function etm_writel_cp14() parameter order
coresight-etm: remove check for unknown Kconfig macro
coresight: fixing CPU hwid lookup in device tree
coresight: remove the unnecessary function coresight_is_bit_set()
coresight: fix the debug AMBA bus name
coresight: remove the extra spaces
coresight: fix the link between orphan connection and newly added device
coresight: remove the unnecessary replicator property
coresight: fix the replicator subtype value
pdfdocs: Fix 'make pdfdocs' failure for 'uio-howto.tmpl'
mcb: Fix error path of mcb_pci_probe
virtio/console: verify device has config space
ti-st: clean up data types (fix harmless memory corruption)
mei: me: release hw from reset only during the reset flow
mei: mask interrupt set bit on clean reset bit
extcon: max77693: Constify struct regmap_config
extcon: adc-jack: Release IIO channel on driver remove
extcon: Remove duplicated include from extcon-class.c
Drivers: hv: vmbus: hv_process_timer_expiration() can be static
Drivers: hv: vmbus: serialize Offer and Rescind offer
...
struct acpi_resource_address and struct acpi_resource_extended_address64 share substracts
just at different offsets. To unify the parsing functions, OSPMs like Linux
need a new ACPI_ADDRESS64_ATTRIBUTE as their substructs, so they can
extract the shared data.
This patch also synchronizes the structure changes to the Linux kernel.
The usages are searched by matching the following keywords:
1. acpi_resource_address
2. acpi_resource_extended_address
3. ACPI_RESOURCE_TYPE_ADDRESS
4. ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS
And we found and fixed the usages in the following files:
arch/ia64/kernel/acpi-ext.c
arch/ia64/pci/pci.c
arch/x86/pci/acpi.c
arch/x86/pci/mmconfig-shared.c
drivers/xen/xen-acpi-memhotplug.c
drivers/acpi/acpi_memhotplug.c
drivers/acpi/pci_root.c
drivers/acpi/resource.c
drivers/char/hpet.c
drivers/pnp/pnpacpi/rsparser.c
drivers/hv/vmbus_drv.c
Build tests are passed with defconfig/allnoconfig/allyesconfig and
defconfig+CONFIG_ACPI=n.
Original-by: Thomas Gleixner <tglx@linutronix.de>
Original-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
drivers/hv/vmbus_drv.c:582:6: sparse: symbol 'hv_process_timer_expiration' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4b2f9abea5 ("staging: hv: convert channel_mgmt.c to not call
osd_schedule_callback")' was written under an assumption that we never receive
Rescind offer while we're still processing the initial Offer request. However,
the issue we fixed in 04a258c162 could be caused by this assumption not
always being true.
In particular, we need to protect against the following:
1) Receiving a Rescind offer after we do queue_work() for processing an Offer
request and before we actually enter vmbus_process_offer(). work.func points
to vmbus_process_offer() at this moment and in vmbus_onoffer_rescind() we do
another queue_work() without a check so we'll enter vmbus_process_offer()
twice.
2) Receiving a Rescind offer after we enter vmbus_process_offer() and
especially after we set >state = CHANNEL_OPEN_STATE. Many things can go
wrong in that case, e.g. we can call free_channel() while we're still using
it.
Implement the required protection by changing work->func at the very end of
vmbus_process_offer() and checking work->func in vmbus_onoffer_rescind(). In
case we receive rescind offer during or before vmbus_process_offer() is done
we set rescind flag to true and we check it at the end of vmbus_process_offer()
so such offer will not get lost.
Suggested-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sc_lock spinlock in struct vmbus_channel is being used to not only protect the
sc_list field, e.g. vmbus_open() function uses it to implement test-and-set
access to the state field. Rename it to the more generic 'lock' and add the
description.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmbus_device_create() result is not being checked in vmbus_process_offer() and
it can fail if kzalloc() fails. Add the check and do minor cleanup to avoid
additional duplication of "free_channel(); return;" block.
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case the user-space daemon crashes, hangs or is killed, we
need to down the semaphore, otherwise, after the daemon starts next
time, the obsolete data in fcopy_transaction.message or
fcopy_transaction.fcopy_msg will be used immediately.
Cc: Jason Wang <jasowang@redhat.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the API for sending a multi-page buffer over VMBUS is limited to
a maximum pfn array of MAX_MULTIPAGE_BUFFER_COUNT. This limitation is
not imposed by the host and unnecessarily limits the maximum payload
that can be sent. Implement an API that does not have this restriction.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correctly compute the local (gpadl) handle.
I would like to thank Michael Brown <mcb30@ipxe.org> for seeing this bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Michael Brown <mcb30@ipxe.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement a clockevent device based on the timer support available on
Hyper-V.
In this version of the patch I have addressed Jason's review comments.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently release memory (balloon down) in the interrupt context and we also
post memory status while releasing memory. Rather than posting the status
in the interrupt context, wakeup the status posting thread to post the status.
This will address the inconsistent lock state that Sitsofe Wheeler <sitsofe@gmail.com>
reported:
http://lkml.iu.edu/hypermail/linux/kernel/1411.1/00075.html
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Sitsofe Wheeler <sitsofe@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We support memory hot-add in the Hyper-V balloon driver by hot adding an appropriately
sized and aligned region and controlling the on-lining of pages within that region
based on the pages that the host wants us to online. We do this because the
granularity and alignment requirements in Linux are different from what Windows
expects. The state to manage the onlining of pages needs to be correctly
protected. Fix this bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make adjustments in computing the balloon floor. The current computation
of the balloon floor was not appropriate for virtual machines with more than
10 GB of assigned memory - we would get into situations where the host would
agressively balloon down the guest and leave the guest in an unusable state.
This patch fixes the issue by raising the floor.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace calls for smp_processor_id() to get_cpu() to get the CPU ID of
the current CPU. In these instances, there is no correctness issue with
regards to preemption, we just need the current CPU ID.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a new
subsystem, "coresight" has been added. Full details are in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSODosACgkQMUfUDdst+ykSNwCfcqx1Z3rQzbLwSrR2sa1fV3Zb
yEAAniJoLZ4ZkoQK4/1ozsFc31q+gXNm
=/epr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
This patch adds proper handling of the vNIC hot removal event, which includes
a rescind-channel-offer message from the host side that triggers vNIC close and
removal. In this case, the notices to the host during close and removal is not
necessary because the channel is rescinded. This patch blocks these unnecessary
messages, and lets vNIC removal process complete normally.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If num_ballooned is not 0, we shouldn't neglect the
already-partially-allocated 2MB memory block(s).
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to send a message to userspace daemon with cn_netlink_send()
there is no need to wait for userspace to reply as it is not going to
happen. This happens when kvp or vss daemon is stopped after a successful
handshake. Report HV_E_FAIL immediately and cancel the timeout job so
host won't receive two failures.
Use pr_warn() for VSS and pr_debug() for KVP deliberately as VSS request
are rare and result in a failed backup. KVP requests are much more frequent
after a successful handshake so avoid flooding logs. It would be nice to
have an ability to de-negotiate with the host in case userspace daemon gets
disconnected so we won't receive new requests. But I'm not sure it is
possible.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In contrast with KVP there is no timeout when communicating with
userspace VSS daemon. In case it gets stuck performing freeze/thaw
operation no message will be sent to the host so it will take very
long (around 10 minutes) before backup fails. Introduce 10 second
timeout using schedule_delayed_work().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When build with Debug the following crash is sometimes observed:
Call Trace:
[<ffffffff812b9600>] string+0x40/0x100
[<ffffffff812bb038>] vsnprintf+0x218/0x5e0
[<ffffffff810baf7d>] ? trace_hardirqs_off+0xd/0x10
[<ffffffff812bb4c1>] vscnprintf+0x11/0x30
[<ffffffff8107a2f0>] vprintk+0xd0/0x5c0
[<ffffffffa0051ea0>] ? vmbus_process_rescind_offer+0x0/0x110 [hv_vmbus]
[<ffffffff8155c71c>] printk+0x41/0x45
[<ffffffffa004ebac>] vmbus_device_unregister+0x2c/0x40 [hv_vmbus]
[<ffffffffa0051ecb>] vmbus_process_rescind_offer+0x2b/0x110 [hv_vmbus]
...
This happens due to the following race: between 'if (channel->device_obj)' check
in vmbus_process_rescind_offer() and pr_debug() in vmbus_device_unregister() the
device can disappear. Fix the issue by taking an additional reference to the
device before proceeding to vmbus_device_unregister().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In win8 we have a feature that allows for interrupt driven flow management
for host/guest communication. For instance, if the host were blocked because
there was no space available in the ringbuffer, the host could request that the
guest send an interrupt when space becomes available in the ringbuffer (when
the guest drains the ringbuffer).
While this feature was implemented in the guest a while ago, we had not
advertised that the guest supported this feature. This patch advertises
the support to the host.
For pre-win8 hosts, this has no effect since the size of the ringbuffer
control structure has not changed and all changes have been backward
compatible - unused/reserved space has been used to implement this
feature.
In this version of the patch I have cleaned up the commit log based on
feedback from Greg KH.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable preemption when sampling current processor ID when preemption
is otherwise possible.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minimize failures in this function by pre-allocating the buffer
for posting messages. The hypercall for posting the message can fail
for a number of reasons:
1. Transient resource related issues
2. Buffer alignment
3. Buffer cannot span a page boundry
We address issues 2 and 3 by preallocating a per-cpu page for the buffer.
Transient resource related failures are handled by retrying by the callers
of this function.
This patch is based on the investigation
done by Dexuan Cui <decui@microsoft.com>.
I would like to thank Sitsofe Wheeler <sitsofe@yahoo.com>
for reporting the issue and helping in debuggging.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminate calls to BUG_ON() in vmbus_close_internal().
We have chosen to potentially leak memory, than crash the guest
in case of failures.
In this version of the patch I have addressed comments from
Dan Carpenter (dan.carpenter@oracle.com).
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a bug in vmbus_open() and properly propagate the error. I would
like to thank Dexuan Cui <decui@microsoft.com> for identifying the
issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminate the call to BUG_ON() by waiting for the host to respond. We are
trying to reclaim the ownership of memory that was given to the host and so
we will have to wait until the host responds.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminate calls to BUG_ON() by properly handling errors. In cases where
rollback is possible, we will return the appropriate error to have the
calling code decide how to rollback state. In the case where we are
transferring ownership of the guest physical pages to the host,
we will wait for the host to respond.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Posting messages to the host can fail because of transient resource
related failures. Correctly deal with these failures and increase the
number of attempts to post the message before giving up.
In this version of the patch, I have normalized the error code to
Linux error code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops, some
other new drivers, testing fixes, and other good things. All have been
in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1LcACgkQMUfUDdst+ymaVwCgqMrKFmpduBufOSFROhxlfB5Q
ajsAoNDmIn3pgla+kj23Y5ib20aMi++s
=IdIr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver patches from Greg KH:
"Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops,
some other new drivers, testing fixes, and other good things. All
have been in linux-next for a long time"
* tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (119 commits)
misc: bh1780: Introduce the use of devm_kzalloc
Lattice ECP3 FPGA: Correct endianness
drivers/misc/ti-st: Load firmware from ti-connectivity directory.
dt-bindings: extcon: Add support for SM5502 MUIC device
extcon: sm5502: Change internal hardware switch according to cable type
extcon: sm5502: Detect cable state after completing platform booting
extcon: sm5502: Add support new SM5502 extcon device driver
extcon: arizona: Get MICVDD against extcon device
extcon: Remove unnecessary OOM messages
misc: vexpress: Fix sparse non static symbol warnings
mei: drop unused hw dependent fw status functions
misc: bh1770glc: Use managed functions
pcmcia: remove DEFINE_PCI_DEVICE_TABLE usage
misc: remove DEFINE_PCI_DEVICE_TABLE usage
ipack: Replace DEFINE_PCI_DEVICE_TABLE macro use
drivers/char/dsp56k.c: drop check for negativity of unsigned parameter
mei: fix return value on disconnect timeout
mei: don't schedule suspend in pm idle
mei: start disconnect request timer consistently
mei: reset client connection state on timeout
...
We should schedule the 5s "timer work" before starting the data transfer,
otherwise, the data transfer code may finish so fast on another
virtual cpu that when the code(fcopy_write()) trying to cancel the 5s
"timer work" can occasionally fail because the "timer work" may haven't
been scheduled yet and as a result the fcopy process will be aborted
wrongly by fcopy_work_func() in 5s.
Thank Liz Zhang <lizzha@microsoft.com> for the initial investigation
on the bug.
This addresses https://bugzilla.redhat.com/show_bug.cgi?id=1118123
Tested-by: Liz Zhang <lizzha@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a number of merge issues with changes in this tree and
Linus's tree at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add code to poll the channel since we process only one message
at a time and the host may not interrupt us. Also increase the
receive buffer size since some KVP messages are close to 8K bytes in size.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with Win8, we have implemented several optimizations to improve the
scalability and performance of the VMBUS transport between the Host and the
Guest. Some of the non-performance critical services cannot leverage these
optimization since they only read and process one message at a time.
Make adjustments to the callback dispatch code to account for the way
non-performance critical drivers handle reading of the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All its callers depends on the return value of -ENOBUFS to reallocate a
bigger buffer and retry the receiving. So there's no need to call
pr_err() here since it was not a real issue, otherwise syslog will be
flooded by this false warning.
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
The uuid structure could be managed as a const in several places.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We try to free two pages when only one has been allocated.
Cleanup path is unlikely, so I haven't found any trace that would fit,
but I hope that free_pages_prepare() does catch it.
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code posts periodic memory pressure status from a dedicated thread.
Under some conditions, especially when we are releasing a lot of memory into
the guest, we may not send timely pressure reports back to the host. Fix this
issue by reporting pressure in all contexts that can be active in this driver.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pfncount is of type u32 and thus can never be smaller than 0.
Found by the coverity scanner, CID 143213.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the mapping of the relID to channel is done under the protection of a
single spin lock. Starting with ws2012, each channel is bound to a specific VCPU
in the guest. Use this binding to eliminate the spin lock by setting up
per-cpu state for mapping relId to the channel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By ensuring that we set the callback handler to NULL in the channel close
path on the same CPU that the channel is bound to, we can eliminate this lock
acquisition and release in a performance critical path.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only ws2012r2 hosts support the ability to reconnect to the host on VMBUS. This functionality
is needed by kexec in Linux. To use this functionality we need to negotiate version 3.0 of the
VMBUS protocol.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7ArIACgkQMUfUDdst+ylS+gCfcJr0Zo2v5aWnqD7rFtFETmFI
LhcAoNTQ4cvlVdxnI0driWCWFYxLj6at
=aj+L
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
Compiling last minute changes without setting the proper config
options is not really clever.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The vmbus/hyperv interrupt handling is another complete trainwreck and
probably the worst of all currently in tree.
If CONFIG_HYPERV=y then the interrupt delivery to the vmbus happens
via the direct HYPERVISOR_CALLBACK_VECTOR. So far so good, but:
The driver requests first a normal device interrupt. The only reason
to do so is to increment the interrupt stats of that device
interrupt. For no reason it also installs a private flow handler.
We have proper accounting mechanisms for direct vectors, but of
course it's too much effort to add that 5 lines of code.
Aside of that the alloc_intr_gate() is not protected against
reallocation which makes module reload impossible.
Solution to the problem is simple to rip out the whole mess and
implement it correctly.
First of all move all that code to arch/x86/kernel/cpu/mshyperv.c and
merily install the HYPERVISOR_CALLBACK_VECTOR with proper reallocation
protection and use the proper direct vector accounting mechanism.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linuxdrivers <devel@linuxdriverproject.org>
Cc: x86 <x86@kernel.org>
Link: http://lkml.kernel.org/r/20140223212739.028307673@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use a resource for the hyperv mmio region instead of start/size
variables. Register the region properly so it shows up in
/proc/iomem.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the file copy service for Linux guests on Hyper-V. This permits the
host to copy a file (over VMBUS) into the guest. This facility is part of
"guest integration services" supported on the Windows platform.
Here is a link that provides additional details on this functionality:
http://technet.microsoft.com/en-us/library/dn464282.aspx
In V1 version of the patch I have addressed comments from
Olaf Hering <olaf@aepfle.de> and Dan Carpenter <dan.carpenter@oracle.com>
In V2 version of this patch I did some minor cleanup (making some globals
static). In V4 version of the patch I have addressed all of Olaf's
most recent set of comments/concerns.
In V5 version of the patch I had addressed Greg's most recent comments.
I would like to thank Greg for suggesting that I use misc device; it has
significantly simplified the code.
In V6 version of the patch I have cleaned up error message based on Olaf's
comments. I have also rebased the patch based on the current tip.
In this version of the patch, I have addressed the latest comments from Greg.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-interruptible sleep of the memory pressure posting thread
results in higher reported load average. Make this sleep interruptible.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows replying only to the requestor portid while still
supporting broadcasting. Pass 0 to portid for the previous behavior.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current channel code is using scatterlist abstraction to pass data to the
ringbuffer API on the send path. This causes unnecessary translations
between virtual and physical addresses. Fix this.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Gen2 firmware, Hyper-V does not emulate the PCI bus. However, the MMIO
information is packaged up in DSDT. Extract this information and export it
for use by the synthetic framebuffer driver. This is the only driver that
needs this currently.
In this version of the patch mmio, I have updated the hyperv header file
(linux/hyperv.h) with mmio definitions.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the guest attempts to connect with the host when there may already be a
connection with the host (as would be the case during the kdump/kexec path),
it is difficult to guarantee timely response from the host. Starting with
WS2012 R2, the host supports this ability to re-connect with the host
(explicitly to support kexec). Prior to responding to the guest, the host
needs to ensure that device states based on the previous connection to
the host have been properly torn down. This may introduce unbounded delays.
To deal with this issue, don't do a timed wait during the initial connect
with the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the initial VMBUS connect phase, starting with WS2012 R2, we should
specify the VPCU in the guest that should receive the notification. Fix this
issue. This fix is required to properly connect to the host in the kexeced
kernel.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will allow us to use bigger receive buffer, and prevent allocation failure
due to fragmented memory.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
This patch marks the function hv_synic_free_cpu() as static in hv.c
because it is not used outside this file.
Thus, it also eliminates the following warning in hv.c:
drivers/hv/hv.c:304:6: warning: no previous prototype for ‘hv_synic_free_cpu’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rescind of subchannels were not being correctly handled. Fix the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.11+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check for calling free_page() on hv_context.synic_event_page[cpu] is the
same for hv_context.synic_message_page[cpu], like a copy-paste error.
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need/want the mei fixes in here so we can apply other updates that
are depending on them.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't return success if the buffer has not been initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 666b9adc80 terminated vmbus
version negotiation incorrectly. We need to terminate the version
negotiation only if the current negotiation were to timeout.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <ohering@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code does not correctly negotiate the version numbers for the util
driver when hosted on earlier hosts. The version numbers presented by this
driver were not compatible with the version numbers supported by Windows Server
2008. Fix this problem.
I would like to thank Olaf Hering (ohering@suse.com) for identifying the problem.
Reported-by: Olaf Hering <ohering@suse.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the ringbuffer bus attributes to the dev_groups structure,
deletes the now unneeded struct hv_device_info, and removes some now
unused functions, and variables as everything is now moved to the
dev_groups structure, dev_attrs is no longer needed.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's no longer needed, and the struct hv_ring_buffer_debug_info
structure shouldn't be "global" so move it to the local .h file instead.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's only used once, only contains 2 function calls, so just make those
calls directly, deleting the function, and the now unneeded structure
entirely.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the "client_monitor_conn_id" and "server_monitor_conn_id" bus
attributes to the dev_groups structure, removing the need for it to be
in a temporary structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the "client_monitor_latency" and "server_monitor_latency" bus
attributes to the dev_groups structure, removing the need for it to be
in a temporary structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the "client_monitor_pending" and "server_monitor_pending" bus
attributes to the dev_groups structure, removing the need for it to be
in a temporary structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
monitor_pages was a void pointer, containing an unknown number of arrays that
we just "knew" were a child and parent array of a specific size. Instead of
that implicit knowledge, let's make them a real pointer, allowing us to have
type safety, and a semblance of sane addressing schemes.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the "device_id" bus attribute to the dev_groups structure,
removing the need for it to be in a temporary structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the "class_id" bus attribute to the dev_groups structure,
removing the need for it to be in a temporary structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the "state" bus attribute to the dev_groups structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the "state" bus attribute to the dev_groups structure,
removing the need for it to be in a temporary structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the "state" bus attribute to the dev_groups structure,
removing the need for it to be in a temporary structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is the first in a series that moves the hv bus code to use the
dev_groups field instead of dev_attrs, as dev_attrs is going away in future
kernel releases.
It moves the id sysfs file to the dev_groups structure, and creates the needed
show/store functions, instead of relying on one "universal" function for this.
By doing this, it removes the need for this to be in a temporary structure.
Tested-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable execute_shutdown is only assigned the values true and
false. Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code would attempt to negotiate a different protocol version if
the current negotiation timed out. This triggers an assert in the host (on debug
builds). Avoid this by negotiating a newer version only if the host properly
rejects the current version being negotiated.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The channel state should be correctly set before registering the device. In the current
code the driver probe would fail for channels that have been rescinded and subsequently
re-offered. Fix the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove HV_DRV_VERSION, it has no meaning for upstream drivers.
Initially it was supposed to show the "Linux Integration Services"
version, now it is not in sync anymore with the out-of-tree drivers
available from the MSFT website.
The only place where a version string is still required is the KVP
command "IntegrationServicesVersion" which is handled by
tools/hv/hv_kvp_daemon.c. To satisfy such KVP request from the host pass
the current string to the daemon during KVP userland registration.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each message sent from the guest carries with it a transaction ID.
Assign the transaction ID just before putting the message on the VMBUS.
This would help in debugging on the host side.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code picked the highest version advertised by the host. WS2012 R2
has implemented a protocol version for KVP that is not compatible with prior
protocol versions of KVP. Fix the bug in the current code by explicitly specifying
the protocol version that the guest can support.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we are posting pressure status, we may get interrupted and handle
the un-balloon operation. In this case just don't post the status as we
know the pressure status is stale.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we hot-add 128 MB chunks of memory, we wait to ensure that the memory
is onlined before attempting to hot-add the next chunk. If the udev rule for
memory hot-add is not executed within the allowed time, we would rollback the
state and abort further hot-add. Since the hot-add has succeeded and the only
failure is that the memory is not onlined within the allowed time, we should not
be rolling back the state. Fix this bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever a device is unregistered in vmbus_device_unregister (drivers/hv/vmbus_drv.c), the device name in the log message may contain garbage as the memory has already been freed by the time pr_info is called. Log example:
[ 3149.170475] hv_vmbus: child device àõsèè0_5 unregistered
By logging the message just before calling device_unregister, the correct device name is printed:
[ 3145.034652] hv_vmbus: child device vmbus_0_5 unregistered
Also changing register & unregister messages to debug to avoid unnecessarily cluttering the kernel log.
Signed-off-by: Fernando M Soto <fsoto@bluecatnetworks.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently allocate synic structures in hv_sync_init(), but there's no way for
the driver to know about the allocation failure and it may continue to use the
uninitialized pointers. Solve this by introducing helpers for allocating and
freeing and doing the allocation before the on_each_cpu() call in
vmbus_bus_init().
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches add a read barriers to force the driver to check the interrupt mask
before read_index. Otherwise we may lost a kick to host.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if guest were compiled without SMP support, it could not assume that host
wasn't. So switch to use mb() instead of smp_mb() to force memory barriers for
UP guest.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with Win8, the host supports multiple sub-channels for a given
device. As in the past, the initial channel offer specifies the device and
is associated with both the type and the instance GUIDs. For performance
critical devices, the host may support multiple sub-channels. The sub-channels
share the same type and instance GUID as the primary channel. The number of
sub-channels offerrred to the guest depends on the number of virtual CPUs
assigned to the guest. The guest can request the creation of these sub-channels
and once created and opened, the guest can distribute the traffic across all
the channels (the primary and the sub-channels). A request sent on a sub-channel
will have the response delivered on the same sub-channel.
At channel (sub-channel) creation we bind the channel interrupt to a CPU and
with this sub-channel support we will be able to spread the interrupt load
of a given device across all available CPUs.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux' notion of cpuid is different from the Host's notion of CPUID. In the
call to bind the channel interrupts, we should use the host's notion of
CPU Ids. Fix this bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Stable <stable@vger.kernel.org> (V3.9)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull x86 paravirt update from Ingo Molnar:
"Various paravirtualization related changes - the biggest one makes
guest support optional via CONFIG_HYPERVISOR_GUEST"
* 'x86-paravirt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, wakeup, sleep: Use pvops functions for changing GDT entries
x86, xen, gdt: Remove the pvops variant of store_gdt.
x86-32, gdt: Store/load GDT for ACPI S3 or hibernation/resume path is not needed
x86-64, gdt: Store/load GDT for ACPI S3 or hibernate/resume path is not needed.
x86: Make Linux guest support optional
x86, Kconfig: Move PARAVIRT_DEBUG into the paravirt menu
As part of updating the vmbus protocol, the function hv_need_to_signal()
was introduced. This functions helps optimize signalling from guest to
host. The newly added memory barrier is needed to ensure that we correctly
decide when to signal the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-by: Olaf Hering <olh@suse.de>
Cc: Stable <stable@vger.kernel.org> (V3.8+)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If memory hot-add fails with the error -EEXIST, then this is a permanent
failure. Notify the host of this information, so the host will not attempt
hot-add again. If the failure were a transient failure, host will attempt
a hot-add after some delay.
In this version of the patch, I have added some additional comments
to clarify how the host treats different failure conditions.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Hyper-V it will be very efficient to use 2M allocations in the guest as this
makes the ballooning protocol with the host that much more efficient. Hyper-V
uses page ranges (start pfn : number of pages) to specify memory being moved
around and with 2M pages this encoding can be very efficient. However, when
memory is returned to the guest, the host does not guarantee any granularity.
To deal with this issue, split the page soon after a successful 2M allocation
so that this memory can potentially be freed as 4K pages.
If 2M allocations fail, we revert to 4K allocations.
In this version of the patch, based on the feedback from Michal Hocko
<mhocko@suse.cz>, I have added some additional commentary to the patch
description.
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Windows hosts permit the guest to specify memory hot-add alignment
requirements (if any). Linux currently requires a 128MB alignment on memory
segments that can be hot-added. Specify this alignment requirement to the
host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
local functions that could be static.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver supports host initiated backup of the guest. On Windows guests,
the host can generate application consistent backups using the Windows VSS
framework. On Linux, we ensure that the backup will be file system consistent.
This driver allows the host to initiate a "Freeze" operation on all the mounted
file systems in the guest. Once the mounted file systems in the guest are frozen,
the host snapshots the guest's file systems. Once this is done, the guest's file
systems are "thawed".
This driver has a user-level component (daemon) that invokes the appropriate
operation on all the mounted file systems in response to the requests from
the host. The duration for which the guest is frozen is very short - a few seconds.
During this interval, the diff disk is comitted.
In this version of the patch I have addressed the feedback from Olaf Herring.
Also, some of the connector related issues have been fixed.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly cleanup the channel state on receipt of the "offer rescind" message.
Starting with ws2012, the host requires that the channel "relid" be properly
cleaned up when the offer is rescinded.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the memory hot-add functionality. With this, Linux guests can fully
participate in the Dynamic Memory protocol implemented in the Windows hosts.
In this version of the patch, based Olaf Herring's feedback, I have gotten
rid of the module level dependency on MEMORY_HOTPLUG. Instead the code within
the driver that depends on MEMORY_HOTPLUG has the appropriate compilation
switches. This would allow this driver to support pure ballooning in cases
where the kernel does not support memory hotplug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The balloon driver is stateful. For instance, it needs to keep track of pages
that have been ballooned out to properly post pressure reports. This state cannot
be re-constructed if the driver were to be unloaded and subsequently loaded.
Furthermore, as we support memory hot-add as part of this driver, this driver becomes
even more stateful and this state cannot be re-created. Make the balloon driver
unloadable to deal with this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Execute the hot-add operation in a separate work context.
This allows us to decouple the pressure reporting activity from the
"hot-add" activity. Testing has shown that this makes the guest more
responsive to hot add requests.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Execute the balloon inflation operation in a separate work context.
This allows us to decouple the pressure reporting activity from the
ballooning activity. Testing has shown that this decoupling makes the
guest more reponsive.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to request completion notification; get rid of it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put all config options needed to run Linux as a guest behind a
CONFIG_HYPERVISOR_GUEST menu so that they don't get built-in by default
but be selectable by the user. Also, make all units which depend on
x86_hyper, depend on this new symbol so that compilation doesn't fail
when CONFIG_HYPERVISOR_GUEST is disabled but those units assume its
presence.
Sort options in the new HYPERVISOR_GUEST menu, adapt config text and
drop redundant select.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1362428421-9244-3-git-send-email-bp@alien8.de
Cc: Dmitry Torokhov <dtor@vmware.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Use the infrastructure for delivering VMBUS interrupts using a
special vector. With this patch, we can now properly handle
the VMBUS interrupts that can be delivered on any CPU. Also,
turn on interrupt load balancing as well.
This patch requires the infrastructure that was implemented in the patch:
X86: Handle Hyper-V vmbus interrupts as special hypervisor interrupts
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
In order to compile in the special Hyper-V interrupt vector, we need
infrastructure in arch/x86/apic/apic.c. At least for now, simply
require CONFIG_X86_LOCAL_APIC in order to enable CONFIG_HYPERV.
Link: http://lkml.kernel.org/r/tip-bc2b0331e077f576369a2b6c75d15ed4de4ef91f@git.kernel.org
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Based on the amount of memory being managed set a floor on how low the
guest can be ballooned.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delay reporting memory pressure by a specified amount of time.
This addresses the problem where the host may take memory balancing
decisions based on incorrect memory pressure data that will be posted
as soon as the balloon driver is loaded.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host expects that the pressure report includes the pressure due to the
pages that have been ballooned. Make necessary adjustments to reflect that.
Also, include the free memory information in the pressure report.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Execute the shutdown code in a thread context. With recent changes made to the
shutdown code, shutdown code cannot be invoked from an interrupt context.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the consolidated GUID definitions in the util and balloon drivers.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consolidate all GUID definitions in hyperv.h and use these definitions in implementing
channel bindings (as far as interrupt delivery goes).
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default interrupt delivery model in Linux does not support the Hyper-V
vmbus delivery model when the guest is configured with multiple VCPUs. I have
sent a patch to address this - delivering the vmbus interrupt on a separate
IDT vector. Until this patch is applied, bind all vmbus interrupts to the boot
CPU.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The send buffer was being leaked; fix it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is bug in the definition of struct dm_info_msg. This patch fixes
the definition of this structure and makes the corresponding adjustments.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable userlen is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, cleanup and consolidate reporting of host and vmbus version numbers.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Capture the host build information so it can be presented along with the
negotiated vmbus version information.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement flow management on the send side. When the sender is blocked, the reader
can potentially signal the sender to indicate there is now room to send.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have implemented all of the Win8 (WS2012) functionality, negotiate
Win8 protocol with the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We establish the handler before we have fully initialized the VMBUS state.
Deal with spurious interrupts.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vmbus interrupts are unique in that while the interrupt is delivered on a
given vector, these can be handled concurrently on different CPUs. Handle the
vmbus interrupts concurrently on all the CPUs.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we can potentially take vmbus interrupts on any CPU, make the
tasklets per-CPU.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This call to seek offers is not necessary and just adds unnecessary delay.
Get rid of it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have implemented a per-connection signaling mechanism, get rid
of the global signaling state. For hosts that don't support per-connection
signaling handle, we have moved the global state to be a per-channel state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement a simple policy for distributing incoming interrupt load.
We classify channels as (a) performance critical and (b) not
performance critical. All non-performance critical channels will
be bound to the boot cpu. Performance critical channels will be
bound to the remaining available CPUs on a round-robin basis.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with Win8 (WS2012), the event page can be used to directly get the
channel ID that needs servicing. Modify the channel event handling code
to take advantage of this feature.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add state to bind a channel to a specific VCPU. This will help us better
distribute incoming interrupt load.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On win8 (ws2012), incoming vmbus interrupt load can be spread across all
available VCPUs in the guest. On a per-channel basis, the interrupts can
be bound to specific CPUs. The Linux notion of cpu ID may be different
from that of the hypervisor's. Setup a mapping structure.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On win7 (ws2008 R2) and beyond, we have the notion of having dedicated interrupts on
a per-channel basis. When a channel has a dedicated interrupt assigned, there is no need
to set the interrupt bit in the shared page. Implement this optimization.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code has a global handle for supporting signaling of the host
from guest. Make this a per-channel attribute as on some versions of the
host we can signal on per-channel handle.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support version specific optimization in various vmbus drivers,
move the vmbus definitions to the public header file.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for supporting a per-connection signaling mechanism,
change the signature of vmbus_set_event(). This change is also
needed to implement other aspects of the signaling optimization.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for implementing a per-connection signaling framework,
change the signature of the function hv_signal_event(). The current
code uses a global handle for signaling the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export the negotiated vmbus version as this may be useful for
individual drivers.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code hard coded the vmbus version independent of the host
it was running on. Add code to dynamically negotiate the most appropriate
version.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is no longer used; get rid of it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host has already implemented the "read" side optimizations.
Leverage that to optimize "write" side signaling.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have the infratructure for correctly determining when we
should signal the host; optimize the signaling on the read side -
signaling the guest from the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Util driver is not a performance critical driver and furthermore some
util services such as KVP can only handle one outstanding message
from the host. Turn off batched reading for util drivers.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the "read" side signaling optimization, the reader has to completely
drain the queue before exiting. Add state to manage this "batched"
reading.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement functions that will support read-side signaling optimization.
By having the reader indicate the start of the "read" operation and the
"end" of the read operation we can more efficiently handle the signaling
protocol: while the read is in progress, there is no need for the "writer"
to signal the "reader" as new items are put on the read queue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the following sparse warning:
drivers/hv/hv_balloon.c:548:6: sparse: symbol 'free_balloon_pages' was not declared. Should it be static?
Reported-by: Xie ChanglongX <changlongx.xie@intel.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the basic balloon driver. Windows hosts dynamically manage the guest
memory allocation via a combination memory hot add and ballooning. Memory
hot add is used to grow the guest memory upto the maximum memory that can be
allocatted to the guest. Ballooning is used to both shrink as well as expand
up to the max memory. Supporting hot add needs additional support from the
host. We will support hot add when this support is available. For now,
by setting the VM startup memory to the VM max memory, we can use
ballooning alone to dynamically manage memory allocation amongst
competing guests on a given host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a memory leak in the error handling path in the function vmbus_open().
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-by: Jason Wang <jasowang@redhat.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variables guidtype, guidinstance and initiate are initialized but
never used otherwise, so remove the unused variables.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of unnecessary forward declarations.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is part of the IP injection protocol in that the host expects this field
to reflect what addresses (address families) are currently bound to the
interface. The KVP daemon is currently collecting this information and sending
it to the kernel component. I had overlooked copying this and sending it
back to the host. This patch addresses this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two reasons we need to use x86_hyper instead of
query_hypervisor_presence():
- Not only hyperv but also other hypervisors such as kvm would set
X86_FEATURE_HYTPERVISOR, so query_hypervisor_presence() will return true even
in kvm. This may cause extra delay of 5 seconds before failing the probing in
kvm guest.
- The hypervisor has been detected in init_hypervisor(), so no need to do the
work again.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We wait for about 5 seconds for the success of the hyperv registration even if
we were not in hyperv platform. This is suboptimal, so the patch check the cpuid
in the beginning of hv_acpi_init() instead of in vmbus_bus_init() to fail the
probing immediately.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement support for the new IP injection messages in the driver code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to implementing IP injection, cleanup the way we propagate
and handle errors both in the driver as well as in the user level daemon.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the necessary definitions for supporting the IP injection functionality.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format GUIDS as per MSFT standard. This makes interacting with MSFT
tool stack easier.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current guest ID string in use in vmbus driver does not conform
to the MSFT guidelines on guest ID. MSFT currently does not specify
Linux specific guidelines. MSFT however has plans to publish Linux
specific guidelines. This implementation conforms to the yet unpublished
Linux specific guidelines for guest ID. This implementation also broadly
conforms to the current guidelines as well.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
The hex constant chosen for HV_LINUX_GUEST_ID_HI was offensive, update to use
the decimal equivalent instead.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging switch
driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
VOQAnAriySv397St36J6Hz5bMQZwB1Yq
=SQc+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
The current version negotiation code is not "future proof". Fix this
by allowing each service the flexibility to either specify the highest
version it can support or it can support the highest version number
the host is offering.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vmbus_prep_negotiate_resp() is only invoked when we are negotiating
the version; so the current check in vmbus_prep_negotiate_resp()
is unnecessary. Get rid of it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function returns negative error codes, but because the type is u16
they get truncated into positive numbers. It doesn't look like the
callers care, but we should fix it anyway as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the existing code, we only stop queue when the ringbuffer is full,
so the current packet has to be dropped or retried from upper layer.
This patch stops the tx queue when available ringbuffer is below
the low watermark. So the ringbuffer still has small amount of space
available for the current packet. This will reduce the overhead of
retries on sending.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have only supported enumeration only from the AUTO pool. Now support
enumeration from all the available pools.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support the newly defined KVP message types. It turns out that the host
pushes a set of standard key value pairs as soon as the guest opens the KVP channel.
Since we cannot handle these tuples until the user level daemon loads up, defer
reading the KVP channel until the user level daemon is launched.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add additional KVP (Key Value Pair) protocol messages to
enhance KVP functionality for Linux guests on Hyper-V. As part of this,
patch define an explicit version negoitiation message.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code arbirarily limited the number of CPUs the guest could have.
Change that so that we can support the maximum number of CPUs the guest can
support. While we use NR_CPUS to size the per-cpu state all we are allocating
based on NR_CPUS are the pointers to per-cpu state that will be allocatted in
the context of the initializing CPU. This patch triggers a checkpatch warning
for the usage of NR_CPU and since all we are allocating a couple of pointers
per CPU, it should be ok.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, cleanup the user/kernel KVP protocol by using the same structure
definition that is used for host/guest KVP protocol. This simplifies the code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for consolidating all KVP related defines into a single header file
that both the kernel and user level components can use, move the contents of
hv_kvp.h into hyperv.h.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current KVP code carries some private connector related defines.
Update connector.h to have all the KVP defines. As part of this patch
get rid of some unused defines.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code unnecessarily limits the number of offers we handle.
Get rid of this limitation. As part of this cleanup, also get rid of an
unused define - MAX_MSG_TYPES.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function vmbus_exists() was introduced recently to deal with cases where
the vmbus driver failed to initialize and yet other Hyper-V drivers attempted
to register with the vmbus bus driver. This patch introduced a bug where
vmbus_driver_unregister() would fail to unregister the driver. This patch
fixes the problem.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Fuzhou Chen <fuzhouch@microsoft.com>
Cc: Sasha Levin <levinsasha928@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In preparation for eventually supporting kexec in Linux VMs on Hyper-V,
get rid of an unnecessary check in hv_init().
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that the vmbus driver can be made unloadable. Make it
unloadable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was a memory leak in a failure path in vmbus_process_offer().
Fix it.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hv vmbus driver was causing an OOPS since it was trying to register drivers
on top of the bus even if initialization of the bus has failed for some
reason (such as the odd chance someone would run a hv enabled kernel in a
non-hv environment).
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of the drivers/*/Kconfig files define a menu entry. Define
a menu item for hv too such that it becomes uniform with e.g.
virtio for at least "make xconfig" and "make menuconfig" users.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the way we initialize the vmbus driver so that all the hyper-v drivers
can be linked with the kernel and still ensure that the vmbus driver
is fully initialized before the drivers that depend upon the vmbus
driver attempt to initialize.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The utf8s_to_utf16s conversion routine needs to be improved. Unlike
its utf16s_to_utf8s sibling, it doesn't accept arguments specifying
the maximum length of the output buffer or the endianness of its
16-bit output.
This patch (as1501) adds the two missing arguments, and adjusts the
only two places in the kernel where the function is called. A
follow-on patch will add a third caller that does utilize the new
capabilities.
The two conversion routines are still annoyingly inconsistent in the
way they handle invalid byte combinations. But that's a subject for a
different patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is only used/needed by the vmbus core code, so move it out of the
hyperv.h file and into the .c file that uses it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function is only used in the file it is declared in
(channel_mgmt.c) so make it static and remove it from the hyperv.h file.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As there is no user of this variable, it's time to delete it. For
dynamic debugging of the hyperv code, use the standard dynamic debug
kernel interface.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a global symbol, so properly prefix it and use the proper EXPORT
value as well.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No one outside of the hyperv core needs to include the asm/hyperv.h
file, so don't put it in the "global" include/linux/hyperv.h file.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After many years wandering the desert, it is finally time for the
Microsoft HyperV code to move out of the staging directory. Or at least
the core hyperv bus code, and the utility driver, the rest still have
some review to get through by the various subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
K. Y. Srinivasan
Vitaly Kuznetsov
Keith Mange
Dexuan Cui
Haiyang Zhang
Dan Carpenter
Nick Meier
kbuild test robot
Nicholas Mc Guire
Linus Torvalds
Lv Zheng
Greg Kroah-Hartman
Jason Wang
stephen hemminger
Radim Krčmář
Tobias Klauser
Thomas Gleixner
Gerd Hoffmann
David Fries
Rashika Kheria
Felipe Pena
Peter Senna Tschudin
Olaf Hering
Fernando Soto
Wei Yongjun
Zhang Yanfei
Borislav Petkov
H. Peter Anvin
Theodore Ts'o
Bart Van Assche
Alan Stern
Greg Kroah-Hartman