The variable err is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is redundant
and can be removed. Also re-order variable declarations in reverse
Christmas tree ordering.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel says:
====================
ag71xx: add ethtool and flow control support
The main target of this patches is to provide flow control support
for ag71xx driver. To be able to validate this functionality, I also
added ethtool support with HW counters. So, this patches was validated
with iperf3 and counters showing Pause frames send or received by this
NIC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flow control support. The functionality was tested on AR9331 SoC and
confirmed by iperf3 results and HW counters exported over ethtool.
Following test configurations was used:
iMX6S receiver <--- TL-SG1005D switch <---- AR9331 sender
The switch is supporting symmytric flow control:
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
--->> Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: on
Port: MII
PHYAD: 4
Transceiver: external
Link detected: yes
The iMX6S system was configured to 10Mbit, to let the switch use flow
control:
- ethtool -s eth0 speed 10
With flow control disabled on AR9331:
- ethtool -A eth0 rx off tx off
- iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 66.2 MBytes 55.5 Mbits/sec 0.000 ms 0/47155 (0%) sender
[ 5] 0.00-10.04 sec 11.5 MBytes 9.57 Mbits/sec 1.309 ms 38986/47146 (83%) receiver
With flow control enabled on AR9331:
- ethtool -A eth0 rx on tx on
- iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 15.1 MBytes 12.6 Mbits/sec 0.000 ms 0/10727 (0%) sender
[ 5] 0.00-10.05 sec 11.5 MBytes 9.57 Mbits/sec 1.371 ms 2525/10689 (24%) receiver
Similar results are get in opposite direction by introducing extra CPU
load on AR9331:
- chrt 40 dd if=/dev/zero of=/dev/null &
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic ethtool support. The functionality was tested on AR9331 SoC.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "SLF_OUTWAIT" flag defined in x25_asy.h is not actually used.
It is only cleared at one place in x25_asy.c but is never read or set.
So we can remove it.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found the following warning when using W=1 to build kernel:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret, coe = priv->hw->rx_csum;
When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and
dwxgmac2_get_rx_header_len() return 0 only, without any error code to
report. Therefore, it's better to define get_rx_header_len() as void.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Awogbemila says:
====================
Add GVE Features.
Note: Patch 4 in v3 was dropped.
Patch 4 (patch 5 in v3): Start/stop timer only when report stats is
enabled/disabled.
Patch 7 (patch 8 in v3): Use netdev_info, not dev_info, to log
device link status.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows the driver to report the device link speed
when the ethtool command:
ethtool <nic name>
is run.
Getting the link speed is done via a new admin queue command:
ReportLinkSpeed.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the driver better aware of the connectivity status of the
device. Based on the device's status register, the driver can call
netif_carrier_{on,off}.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Patricio Noyola <patricion@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for batching AQ commands and uses it for creating and
destroying queues.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds per queue NIC stats to ethtool stats and to report-stats.
These stats are always exposed to guest whether or not the
report-stats flag is turned on.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds functionality to report driver stats to Hypervisor.
(Users may want to turn this feature off as a matter of privacy
so a "report-stats" flag is added as an ethtool priv option.
It is also disabled by default.)
The hypervisor would trigger a stats report in case "too many"
packets dropped; the stats would be useful in debugging stuck
queues.
A "stats_report_trigger_cnt" stat is added to count the number of times
the hypervisor attempts to trigger stats report.
A timer is also added so that when report-stats is enabled, stat are
updated once every 20 seconds.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Kuo Zhao <kuozhao@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver to use dev_info/err instead of netif_info/err.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for getting and setting the RX copybreak
value via ethtool.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Kuo Zhao <kuozhao@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches for v5.10. Most noteworthy here is ath11k getting
initial support for QCA6390 and IPQ6018 devices. But most of the
patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API
changes and tasklet API changes.
Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
* add support for QCA6390 PCI devices
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
wcn36xx
* add support for TX ack
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfW5XtAAoJEG4XJFUm622bnuoIAIx8xplr5UYZv/qaMyvBaoNQ
gG7AU3IUs4QibSUabpE7kBpdLVX9O4mC5nLWCutGH1dTrJGIQsnuncW206yOAZPp
+MPOauxBmfkBm61RmJ3beGXan6ZGlE7rwkO0Pf+mqrWk4XVovItKpJUuR+IWliu/
gdVbdC2Uu7bQlv44MI/3xOpx5Xvk5gq/4tPcTOE3b57wIyln0NSKJYOoOuL+i2f/
WDiTgPyA/9x+llrf6sA+oLmEN2F8TpVWSDv6F4mA5E9uYjJrJMEJLosSzohU7+ou
j7gvCMv5F8+XnQYX4T/qJ05axBDQO2zRJ6YynWDoqQss4XW8xaiuQCEmaiHE8GM=
=kS8U
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
First set of patches for v5.10. Most noteworthy here is ath11k getting
initial support for QCA6390 and IPQ6018 devices. But most of the
patches are cleanup: W=1 warning fixes, fallthrough keywords, DMA API
changes and tasklet API changes.
Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
* add support for QCA6390 PCI devices
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
wcn36xx
* add support for TX ack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for v5.10. Major changes:
ath10k
* support SDIO firmware codedumps
* support station specific TID configurations
ath11k
* add support for IPQ6018
Adding raw mode tx/rx support. Also, adding support
for software crypto which depends on raw mode.
To enable raw mode tx/rx:
insmod ath11k.ko frame_mode=0
To enable software crypto:
insmod ath11k.ko crypto_mode=1
These modes could be helpful in debugging crypto related issues.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746c6a52d9-18302a2c-0d6d-4057-aa4b-95960c809646-000000@us-west-2.amazonses.com
Fixes the following warning when using W=1 to build kernel:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_phy_configure’:
drivers/net/ethernet/smsc/smc91x.c:1039:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
int status;
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul says:
====================
net/smc: updates 2020-09-10
Please apply the following patch series for smc to netdev's net-next tree.
This patch series is a mix of various improvements and cleanups.
The patches 1 and 10 improve the handling of large parallel workloads.
Patch 8 corrects a kernel config default for config CCWGROUP on s390.
Patch 9 allows userspace tools to retrieve socket information for more
sockets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 6 types of workers which exist per smc connection. 3 of them
are used for listen and handshake processing, another 2 are used for
close and abort processing and 1 is the tx worker that moves calls to
sleeping functions into a worker.
To prevent flooding of the system work queue when many connections are
opened or closed at the same time (some pattern uperf implements), move
those workers to one of 3 smc-specific work queues. Two work queues are
module-global and used for handshake and close workers. The third work
queue is defined per link group and used by the tx workers that may
sleep waiting for resources of this link group.
And in smc_llc_enqueue() queue the llc_event_work work to the system
prio work queue because its critical that this work is started fast.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the netlink messages to be sent to the userspace
are too big for a single netlink message, send them in
chunks using the netlink_dump infrastructure. Modify the
smc diag dump code so that it can signal to the netlink_dump
infrastructure that it needs to send more data.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/s390/net/pnet.c uses ccwgroup function dev_is_ccwgroup()
in pnetid_by_dev_port().
For s390 the net/smc code makes use of function pnetid_by_dev_port().
Make sure ccwgroup is built into the kernel, if smc is to be built
into the kernel.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_lgr_cleanup_early() schedules the free worker with delay. DMB
unregistering occurs in this delayed worker increasing the risk
to reach the SMCD SBA limit without need. Terminate the
linkgroup immediately, since termination means early DMB unregistering.
For SMCD the global smc_server_lgr_pending lock is given up early.
A linkgroup to be given up with smc_lgr_cleanup_early() may already
contain more than one connection. Using __smc_lgr_terminate() in
smc_lgr_cleanup_early() covers this.
And consolidate smc_ism_put_vlan() and smc_put_device() into smc_lgr_free()
only.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_listen_work() contains already an smc_listen_decline() exit.
Use this exit for smc_listen_rdma_finish() problems as well.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move check whether peer can be reached into smc_pnet_find_ism_by_pnetid().
Thus searching continues for another ism device, if check fails.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smc_clc_send_accept() and smc_clc_send_confirm() are quite similar.
Move common code into a separate function smc_clc_send_confirm_accept().
And introduce separate SMCD and SMCR struct definitions for CLC accept
resp. confirm.
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce stack size for smc_listen_work() and smc_clc_send_proposal()
by dynamic allocation of the CLC buffer to be received or sent.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Field names "srv_first_contact" and "cln_first_contact" are misleading,
since they apply to both, server and client. Rename them to
"first_contact_peer" and "first_contact_local".
Rename "ism_gid" by the more precise name "ism_peer_gid".
Rename version constant "SMC_CLC_V1" into "SMC_V1".
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC starts a separate tcp_listen worker for every SMC socket in
state SMC_LISTEN, and can accept an incoming connection request only,
if this worker is really running and waiting in kernel_accept(). But
the number of running workers is limited.
This patch reworks the listening SMC code and starts a tcp_listen worker
after the SYN-ACK handshake on the internal clc-socket only.
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Reviewed-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krzysztof Kozlowski says:
====================
nfc: s3fwrn5: Few cleanups
Changes since v2:
1. Fix dtschema ID after rename (patch 1/8).
2. Apply patch 9/9 (defconfig change).
Changes since v1:
1. Rename dtschema file and add additionalProperties:false, as Rob
suggested,
2. Add Marek's tested-by,
3. New patches: #4, #5, #6, #7 and #9.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since "s3fwrn5" is not a valid vendor prefix, use new GPIO properties
instead of the deprecated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Bałdyga's email does not work (bounces) since 2016 so remove it.
Additionally there are no review/ack/tested tags from Krzysztof Opasiak
so it looks like the driver is not supported.
As a maintainer of Samsung ARM/ARM64 SoC, I can take care about this
driver and provide some review. However clearly driver is not in
supported mode as I do not work in Samsung anymore.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two functions accept pointer to struct s3fwrn5_fw_info but do not
modify the contents. Make them const so the code is a little bit safer.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses crypto hash functions so it needs to select CRYPTO_HASH.
This fixes build errors:
arc-linux-ld: drivers/nfc/s3fwrn5/firmware.o: in function `s3fwrn5_fw_download':
firmware.c:(.text+0x152): undefined reference to `crypto_alloc_shash'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local variable 'ret' can be removed:
drivers/nfc/s3fwrn5/i2c.c:167:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree property prefix describes the vendor, which in case of
S3FWRN5 chip is Samsung. Therefore the "s3fwrn5" prefix for "en-gpios"
and "fw-gpios" is not correct and should be deprecated. Introduce
properly named properties for these GPIOs but still support deprecated
ones.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree property prefix describes the vendor, which in case of
S3FWRN5 chip is Samsung. Therefore the "s3fwrn5" prefix for "en-gpios"
and "fw-gpios" is not correct and should be deprecated. Introduce
properly named properties for these GPIOs and rename the fw-gpios" to
"wake-gpios" to better describe its purpose.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the Samsung S3FWRN5 NCI NFC controller bindings to dtschema.
This is conversion only so it includes properties with invalid prefixes
(s3fwrn5,en-gpios) which should be addressed later.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/huawei/hinic/hinic_hw_eqs.c:115: warning: Excess function parameter 'hw_handler' description in 'hinic_aeq_register_hw_cb'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/huawei/hinic/hinic_hw_api_cmd.c:382: warning: Excess function parameter 'size' description in 'api_cmd'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'netdev' description in 'hns_set_multicast_list'
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'p' description in 'hns_set_multicast_list'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King
David S. Miller
Oleksij Rempel
Xie He
Luo Jiaxing
David Awogbemila
Patricio Noyola
Sagi Shahar
Kuo Zhao
Catherine Sullivan
Kalle Valo
YueHaibing
Anilkumar Kolli
Venkateswara Naralasetty
Karsten Graul
Guvenc Gulce
Ursula Braun
Krzysztof Kozlowski
Wang Hai