This patch clubs the Renesas controller drivers in one rcar dir.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the CAN FD controller found in Renesas R-Car
SoCs. The controller operates in CAN FD only mode by default.
CAN FD mode supports both Classical CAN & CAN FD frame formats. The
controller supports ISO 11898-1:2015 CAN FD format only.
This controller supports two channels and the driver can enable either
or both of the channels.
Driver uses Rx FIFOs (one per channel) for reception & Common FIFOs (one
per channel) for transmission. Rx filter rules are configured to the
minimum (one per channel) and it accepts Standard, Extended, Data &
Remote Frame combinations.
Note: There are few documentation errors in R-Car Gen3 Hardware User
Manual v0.5E with respect to CAN FD controller. They are listed below:
1. CAN FD interrupt numbers 29 & 30 are listed as per channel
interrupts. However, they are common to both channels (i.e.) they are
global and channel interrupts respectively.
2. CANFD clock is derived from PLL1. This is not documented.
3. CANFD clock is further divided by (1/2) within the CAN FD controller.
This is not documented.
4. The minimum value of NTSEG1 in RSCFDnCFDCmNCFG register is 2 Tq. It
is specified 4 Tq in the manual.
5. The maximum number of message RAM area the controller can use is 3584
bytes. It is specified 10752 bytes in the manual.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The patch adds support for IFI CAN/FD controller [1]. This driver
currently supports sending and receiving both standard CAN and new
CAN/FD frames. Both ISO and BOSCH variant of CAN/FD is supported.
[1] http://www.ifi-pld.de/IP/CANFD/canfd.html
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Just sort the drivers in the Makefile, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Kernel module for Allwinner A10/A20 CAN controller.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The patch adds the basic CAN TX/RX function support for Bosch M_CAN controller.
For TX, only one dedicated tx buffer is used for sending data.
For RX, RXFIFO 0 is used for receiving data to avoid overflow.
Rx FIFO 1 and Rx Buffers are not used currently, as well as Tx Event FIFO.
Due to the message ram can be shared by multi m_can instances
and the fifo element is configurable which is SoC dependant,
the design is to parse the message ram related configuration data from device
tree rather than hardcode define it in driver which can make the message
ram sharing fully transparent to M_CAN controller driver,
then we can gain better driver maintainability and future features upgrade.
M_CAN also supports CANFD protocol features like data payload up to 64 bytes
and bitrate switch at runtime, however, this patch still does not add the
support for these features.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[mkl: Squahed semicolon cleanup by Fengguang Wu]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds xilinx CAN controller support. This driver supports both ZYNQ
CANPS and Soft IP AXI CAN controller.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the CAN controller found in Renesas R-Car SoCs.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Create a directory for all CAN drivers using SPI and move mcp251x driver there.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch implements the functions to add two LED triggers, named
<ifname>-tx and <ifname>-rx, to a canbus device driver.
Triggers are called from specific handlers by each CAN device driver and
can be disabled altogether with a Kconfig option.
The implementation keeps the LED on when the interface is UP and blinks
the LED on network activity at a configurable rate.
This only supports can-dev based drivers, as it uses some support field
in the can_priv structure.
Supported drivers should call devm_can_led_init() and can_led_event() as
needed.
Cleanup is handled automatically by devres, so no *_exit function is
needed.
Supported events are:
- CAN_LED_EVENT_OPEN: turn on tx/rx LEDs
- CAN_LED_EVENT_STOP: turn off tx/rx LEDs
- CAN_LED_EVENT_TX: trigger tx LED blink
- CAN_LED_EVENT_RX: trigger tx LED blink
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver supports GRCAN and CRHCAN CAN controllers available in the GRLIB
VHDL IP core library.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bosch C_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch C_CAN user manual can be
obtained from:
http://www.semiconductors.bosch.de/media/en/pdf/ipmodules_1/c_can/users_manual_c_can.pdf
This patch adds the support for this controller.
The following are the design choices made while writing the controller
driver:
1. Interface Register set IF1 has be used only in the current design.
2. Out of the 32 Message objects available, 16 are kept aside for RX
purposes and the rest for TX purposes.
3. NAPI implementation is such that both the TX and RX paths function
in polling mode.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for the platform:softing device.
This will create (up to) 2 CAN network devices from 1
platform:softing device
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for serial/USB-serial CAN adapters implementing the
LAWICEL ASCII protocol for CAN frame transport over serial lines.
The driver implements the SLCAN line discipline and is heavily based on the
slip.c driver. Therefore the code style remains similar to slip.c to be able
to apply changes of the SLIP driver to the SLCAN driver easily.
For more details see the slcan Kconfig entry.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAN driver of Topcliff PCH
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus.
Topcliff PCH has CAN I/F. This driver enables CAN function.
Signed-off-by: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This core is found on some Freescale SoCs and also some Coldfire
SoCs. Support for Coldfire is missing though at the moment as
they have an older revision of the core which does not have RX FIFO
support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Janz VMOD-ICAN3 is a MODULbus daughterboard which fits onto any
MODULbus carrier board. It is an intelligent CAN controller with a
microcontroller and associated firmware.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: H.J. Oertel <oe@port.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taken from socketcan-svn, fixed remaining todos, cleaned up, tested with a
phyCORE-MPC5200B-IO and a custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI HECC (High End CAN Controller) module is found on many TI devices. It
has 32 hardware mailboxes with full implementation of CAN protocol 2.0B
with bus speeds up to 1Mbps. Specifications of the module are available
on TI web <http://www.ti.com>
Signed-off-by: Anant Gole <anantgole@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the driver for the SoC CAN controller in Atmel's
AT91SAM9263.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for one channel CAN/USB interace CPC-USB/ARM7 from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.com).
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the generic Socket-CAN driver for the Philips SJA1000
full CAN controller.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CAN network device driver interface provides a generic interface to
setup, configure and monitor CAN network devices. It exports a set of
common data structures and functions, which all real CAN network device
drivers should use. Please have a look to the SJA1000 or MSCAN driver
to understand how to use them. The name of the module is can-dev.ko.
Furthermore, it adds a Netlink interface allowing to configure the CAN
device using the program "ip" from the iproute2 utility suite.
For further information please check "Documentation/networking/can.txt"
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the virtual CAN bus (vcan) network driver.
The vcan device is just a loopback device for CAN frames, no
real CAN hardware is involved.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ramesh Shanmugasundaram
Marek Vasut
Gerhard Bertelsmann
Marc Kleine-Budde
Dong Aisheng
Wolfram Sang
Kedareswara rao Appana
Sergei Shtylyov
Stefano Babic
Fabio Baltieri
Andreas Larsson
Wolfgang Grandegger
David S. Miller
Bhupesh Sharma
Kurt Van Dijck
Oliver Hartkopp
Masayuki Ohtake
Ira W. Snyder
Barry Song
Wolfram Sang
Christian Pellegrin
Anant Gole
Sebastian Haas
Oliver Hartkopp