This makes it possible to enqueue frames also from atomic context which
is needed for example, when networking packets are sent over a
Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service driver might need to check if there was an error
with the descriptor when in frame mode. We also add two Rx specific
error flags RING_DESC_CRC_ERROR and RING_DESC_BUFFER_OVERRUN.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are used by Thunderbolt services to send and receive frames over
the high-speed DMA rings.
We also put the functions to tb_ namespace to make sure we do not
collide with others and add missing kernel-doc comments for the exported
functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When high-speed DMA paths are used to transfer arbitrary data over a
Thunderbolt link, DMA rings should be in frame mode instead of raw mode.
The latter is used by the control channel (ring 0). In frame mode each
data frame can hold up to 4kB payload.
This patch modifies the DMA ring code to allow configuring a ring to be
in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when
it is allocated. In addition there might be need to enable end-to-end
(E2E) workaround for the ring to prevent losing Rx frames in certain
situations. We add another flag (RING_FLAG_E2E) that can be used for
this purpose.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.
The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.
Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.
This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service might need to find the physical port from a link
the cable is connected to. For instance networking driver uses this
information to generate MAC address according the Apple ThunderboltIP
protocol.
Move this function to thunderbolt.h and rename it to
tb_phy_port_from_link() to reflect the fact that it does not take switch
as parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are needed by Thunderbolt services so move them to thunderbolt.h
to make sure they are available outside of drivers/thunderbolt.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These will be needed by Thunderbolt services when sending and receiving
XDomain control messages. While there change TB_CFG_PKG_PREPARE_TO_SLEEP
value to be decimal in order to be consistent with other members.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thunderbolt XDomain discovery protocol uses directories which contain
properties and other directories to exchange information about what
capabilities the remote host supports. This also includes identification
information like device ID and name.
This adds support for parsing and formatting these properties and
establishes an API drivers can use in addition to the core Thunderbolt
driver. This API is exposed in a new header: include/linux/thunderbolt.h.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These messages are all 32-bit aligned and they should be packed without
the __packed attribute just fine. It also allows compiler to generate
better code on some architectures.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will be using these when communicating XDomain discovery protocol
over Thunderbolt link but they might be useful for other drivers as
well.
Make them available through byteorder/generic.h.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Fixlets
Couple of small nit fixes from Petr
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
flow_dissector: dissect tunnel info
Move dissection of tunnel info from the flower classifier to the flow
dissector where all other dissection occurs. This should not have any
behavioural affect on other users of the flow dissector.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move dissection of tunnel info from the flower classifier to the flow
dissector where all other dissection occurs. This should not have any
behavioural affect on other users of the flow dissector.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the skb parameter of skb_metadata_dst() and skb_tunnel_info()
const as they are not modified. This is in preparation for using
them in call-sites where skb is const.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions static to fix
HOSTCC samples/bpf/xdp_monitor_user.o
samples/bpf/xdp_monitor_user.c:64:7: warning: no previous prototype for ‘gettime’ [-Wmissing-prototypes]
__u64 gettime(void)
^~~~~~~
samples/bpf/xdp_monitor_user.c:209:6: warning: no previous prototype for ‘print_bpf_prog_info’ [-Wmissing-prototypes]
void print_bpf_prog_info(void)
^~~~~~~~~~~~~~~~~~~
Fixes: 3ffab54602 ("samples/bpf: xdp_monitor tool based on tracepoints")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event that mfc->mfc_un.res.ttls[i] is 255 for all
values of i from 0 to MAXIVS-1, the err is not set at all and hence
has a garbage value on the error return at the end of the function,
so initialize it to 0. Also, the error return check on err and goto
to err: inside the for loop makes it impossible for err to be zero
at the end of the for loop, so we can remove the redundant err check
at the end of the loop.
Detected by CoverityScan CID#1457207 ("Unitialized scalar value")
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Gorski says:
====================
bcm63xx_enet: small fixes and cleanups
This patch set fixes a few theoretical issues and cleans up the code a
bit. It also adds a bit more managed function usage to simplify clock
and iomem usage.
Based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use anyhing from that file, so drop it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_disable and clk_unprepare are NULL-safe, so need to duplicate the
NULL check of the functions.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use managed functions where possible to reduce the amount of resource
handling on error and remove paths.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not rely on the shared device being probed before the enet(sw)
devices. This makes it easier to eventually move out the shared
device as a dma controller driver (what it should be).
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA controller regs actually point to DMA channel 0, so the write to
ENETDMA_CFG_REG will actually modify a random DMA channel.
Since DMA controller registers do not exist on BCM6345, guard the write
with the usual check for dma_has_sram.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return code of prepare_enable and change one last instance of
enable only to prepare_enable. Also properly disable and release the
clock in error paths and on remove for enetsw.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is unused, and furthermore it is buggy since it suffers
from the same issue that requires IP6_ECN_set_ce() to take a pointer
to the skb so that it may (in case of CHECKSUM_COMPLETE) update skb->csum
Instead of fixing it, let's just outright remove it.
Tested: builds, and 'git grep IP6_ECN_clear' comes up empty
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require different time period in
second to disable Fastopen on active TCP sockets.
Tested:
Simulate following similar situation that the server's data gets dropped
after 3WHS.
C ---- syn-data ---> S
C <--- syn/ack ----- S
C ---- ack --------> S
S (accept & write)
C? X <- data ------ S
[retry and timeout]
And then print netstat of TCPFastOpenBlackhole, the counter increased as
expected when the firewall blackhole issue is detected and active TFO is
disabled.
# cat /proc/net/netstat | awk '{print $91}'
TCPFastOpenBlackhole
1
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require different tcp_fastopen_key
independently of the host.
David Miller pointed out there is a leak without releasing the context
of tcp_fastopen_key during netns teardown. So add the release action in
exit_batch path.
Tested:
1. Container namespace:
# cat /proc/sys/net/ipv4/tcp_fastopen_key:
2817fff2-f803cf97-eadfd1f3-78c0992b
cookie key in tcp syn packets:
Fast Open Cookie
Kind: TCP Fast Open Cookie (34)
Length: 10
Fast Open Cookie: 1e5dd82a8c492ca9
2. Host:
# cat /proc/sys/net/ipv4/tcp_fastopen_key:
107d7c5f-68eb2ac7-02fb06e6-ed341702
cookie key in tcp syn packets:
Fast Open Cookie
Kind: TCP Fast Open Cookie (34)
Length: 10
Fast Open Cookie: e213c02bf0afbc8a
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'publish' logic is not necessary after commit dfea2aa654 ("tcp:
Do not call tcp_fastopen_reset_cipher from interrupt context"), because
in tcp_fastopen_cookie_gen，it wouldn't call tcp_fastopen_init_key_once.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require enable TCP Fast Open
feature independently of the host.
This patch series continues making more of the TCP Fast Open related
sysctl knobs be per net-namespace.
Reported-by: Luca BRUNO <lucab@debian.org>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: change dsa_ptr for a dsa_port
With DSA, a master net_device is physically wired to a dedicated CPU
switch port. For interaction with the DSA layer, the struct net_device
contains a dsa_ptr, which currently points to a dsa_switch_tree object.
This is only valid for a switch fabric with a single CPU port. In order
to support switch fabrics with multiple CPU ports, we first need to
change the type of dsa_ptr to what it really is: a dsa_port object.
This is what this patchset does. The first patches adds a
dsa_master_get_slave helper and cleans up portions of DSA core to make
the next patches more readable. These next patches prepare the xmit and
receive hot paths and finally change dsa_ptr.
Changes in v2:
- introduce dsa_master_get_slave helper to simplify patch 6
- keep hot path data at beginning of dsa_port for cacheline 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_ptr is a dsa_port instance, there is no need to keep
the tag operations in the dsa_switch_tree structure. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With DSA, a master net device (CPU facing interface) has a dsa_ptr
pointer to which hangs a dsa_switch_tree. This is not correct because a
master interface is wired to a dedicated switch port, and because we can
theoretically have several master interfaces pointing to several CPU
ports of the same switch fabric.
Change the master interface's dsa_ptr for the CPU dsa_port pointer.
This is a step towards supporting multiple CPU ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to make DSA master devices point to their corresponding
CPU port instead of the whole tree, add copies of dst and rcv in the
dsa_port structure so that we keep fast access in the receive hot path.
Also keep the copies at the beginning of the dsa_port structure in order
to ensure they are available in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging protocol operations are specific to each CPU port,
thus the dsa_device_ops pointer belongs to the dsa_port structure.
>From now on assign a slave's xmit copy from its CPU port tagging
operations. This will ease the future support for multiple CPU ports.
Also keep the tag_ops at the beginning of the dsa_port structure so that
we ensure copies for hot path are in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resolving the DSA tagging protocol used by a CPU switch, use a
temporary "tag_ops" variable to store the dsa_device_ops instead of
using directly dst->tag_ops. This will make the future patches moving
this pointer around easier to read.
There is no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that the master device is linked to a CPU port by using
"cpu_dp" for the dsa_port variable in master.c instead of "port", then
use a "port" variable to describe the port index, as usually seen in
other places of DSA core.
This will make the future patch touching dsa_ptr more readable. There is
no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging code does not need to know about the DSA architecture,
it only needs to return the slave device corresponding to the source
port index (and eventually the source device index for cascade-capable
switches) parsed from the frame received on the master device.
For this purpose, provide an inline dsa_master_get_slave helper which
validates the device and port indexes and look up the slave device.
This makes the tagging rcv functions more concise and robust, and also
makes dsa_get_cpu_port obsolete.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pointer ndev is being dereferenced with the call to netif_running
before it is being null checked. Re-order the code to only dereference
ndev after it has been null checked.
Detected by CoverityScan, CID#1457206 ("Dereference before null check")
Fixes: 9df8f79a4d ("net: hns3: Add DCB support when interacting with network stack")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the numbers of events for stop_queue and wake_queue in
ethtool stats.
Example:
ethtool -S eth0
NIC statistics:
...
stop_queue: 7
wake_queue: 7
...
Signed-off-by: Simon Xiao <sixiao@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses u64_to_user_ptr() to cast info.map_ids to a userspace ptr.
It also tags the user_map_ids with '__user' for sparse check.
Fixes: cb4d2b3f03 ("bpf: Add name, load_time, uid and map_ids to bpf_prog_info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment of -EINVAL to variable ret is redundant as it
is being overwritten on the following error exit paths or
to the return value from the following call to basic_set_parms.
Fix this up by removing it. Cleans up clang warning message:
net/sched/cls_basic.c:185:2: warning: Value stored to 'err' is never read
Fixes: 1d8134fea2 ("net_sched: use idr to allocate basic filter handles")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ipmr_notifier_init is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
warning: symbol 'ipmr_notifier_init' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State is initially reported as UNKNOWN. Before register call
netif_carrier_off(). Once the device is opened, call netif_carrier_on() in
order to set the state to UP.
Signed-off-by: Mick Tarsel <mjtarsel@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e85ec74ace ("net: dsa: bcm_sf2: Defer port
enabling to calling port_enable") because this now makes an unbind
followed by a bind to fail connecting to the ingrated PHY.
What this patch missed is that we need the PHY to be enabled with
bcm_sf2_gphy_enable_set() before probing it on the MDIO bus. This is
correctly done in the ops->setup() function, but by the time
ops->port_enable() runs, this is too late. Upon unbind we would power
down the PHY, and so when we would bind again, the PHY would be left
powered off.
Fixes: e85ec74ace ("net: dsa: bcm_sf2: Defer port enabling to calling port_enable")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-09-29
This series contains updates to i40e and i40evf only.
Jake provides several of the changes starting with the renaming of a
variable to clarify what the value is actually calculating. Found we
were misusing the __I40E_RECOVERY_PENDING bit to determine when we
should actually request a new IRQ in i40e_setup_misc_vector(), which
lead to a design mistake, so to resolve the issue, use a separate
state bit for miscellaneous IRQ setup and fix up the design while we
are at it. Cleaned up the old legacy PM support in the driver since
we support the newer generic PM callbacks. Fixed a failure to
hibernate issue, where on some platforms with a large number of CPUs,
we would allocate many IRQ vectors which we would try to migrate to
CPU0 when hibernating.
Sudheer cleans up a check for unqualified module inside i40e_up_complete()
because the link state information is in flux at time, so log messages
are getting logged with incorrect link state information. Also provided
additional log message cleanups and simplify member variable access in
the printing of the link messages.
Mariusz relaxes the firmware check since Fortville and Fort Park NICs
can and do have different firmware versions, so only warn for older
Fortville firmware. Fixed an errata with a flow director statistic that
was not wrapping as expected, simply reset after reading.
Mitch prevents consternation by lowering the log level to debug on a
message seen regularly on VF reset or unload, which is meaningless under
normal circumstances. Refactor the firmware version checking since
Fortville and Fort Park devices can have different firmware versions.
Alan fixes a ring to vector mapping, where the past implementation
attempted to map each Tx and Rx ring to its own vector, however we use
combined queues so we should be mapping the Tx/Rx rings together on one
vector. Adds the ability for the VF to request a different number of
queues allocated to it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on len is redundant as it is always greater than 1,
so just remove it and make the printk less complex.
Detected by CoverityScan, CID#1226729 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mika Westerberg
David S. Miller
Petr Machata
Florian Westphal
Simon Horman
Stephen Hemminger
Colin Ian King
Jonas Gorski
Maciej Żenczykowski
Haishuang Yan
Vivien Didelot
Simon Xiao
Martin KaFai Lau
Mick Tarsel
Florian Fainelli