Commit d015fe995 'powerpc/cell/axon-msi: Retry on missing interrupt'
has turned a rare failure to kexec on QS22 into a reproducible
error, which we have now analysed.
The problem is that after a kexec, the MSIC hardware still points
into the middle of the old ring buffer. We set up the ring buffer
during reboot, but not the offset into it. On older kernels, this
would cause a storm of thousands of spurious interrupts after a
kexec, which would most of the time get dropped silently.
With the new code, we time out on each interrupt, waiting for
it to become valid. If more interrupts come in that we time
out on, this goes on indefinitely, which eventually leads to
a hard crash.
The solution in this commit is to read the current offset from
the MSIC when reinitializing it. This now works correctly, as
expected.
Reported-by: Dirk Herrendoerfer <d.herrendoerfer@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
careful_allocation() was calling into the bootmem allocator for
nodes which had not been fully initialized and caused a previous
bug: http://patchwork.ozlabs.org/patch/10528/ So, I merged a
few broken out loops in do_init_bootmem() to fix it. That changed
the code ordering.
I think this bug is triggered by having reserved areas for a node
which are spanned by another node's contents. In the
mark_reserved_regions_for_nid() code, we attempt to reserve the
area for a node before we have allocated the NODE_DATA() for that
nid. We do this since I reordered that loop. I suck.
This is causing crashes at bootup on some systems, as reported
by Jon Tollefson.
This may only present on some systems that have 16GB pages
reserved. But, it can probably happen on any system that is
trying to reserve large swaths of memory that happen to span other
nodes' contents.
This commit ensures that we do not touch bootmem for any node which
has not been initialized, and also removes a compile warning about
an unused variable.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It looks like most of the hugetlb code is doing the correct thing if
hugepages are not supported, but the mmap code is not. If we get into
the mmap code when hugepages are not supported, such as in an LPAR
which is running Active Memory Sharing, we can oops the kernel. This
fixes the oops being seen in this path.
oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=1024 NUMA pSeries
Modules linked in: nfs(N) lockd(N) nfs_acl(N) sunrpc(N) ipv6(N) fuse(N) loop(N)
dm_mod(N) sg(N) ibmveth(N) sd_mod(N) crc_t10dif(N) ibmvscsic(N)
scsi_transport_srp(N) scsi_tgt(N) scsi_mod(N)
Supported: No
NIP: c000000000038d60 LR: c00000000003945c CTR: c0000000000393f0
REGS: c000000077e7b830 TRAP: 0300 Tainted: G
(2.6.27.5-bz50170-2-ppc64)
MSR: 8000000000009032 <EE,ME,IR,DR> CR: 44000448 XER: 20000001
DAR: c000002000af90a8, DSISR: 0000000040000000
TASK = c00000007c1b8600[4019] 'hugemmap01' THREAD: c000000077e78000 CPU: 6
GPR00: 0000001fffffffe0 c000000077e7bab0 c0000000009a4e78 0000000000000000
GPR04: 0000000000010000 0000000000000001 00000000ffffffff 0000000000000001
GPR08: 0000000000000000 c000000000af90c8 0000000000000001 0000000000000000
GPR12: 000000000000003f c000000000a73880 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000010000
GPR20: 0000000000000000 0000000000000003 0000000000010000 0000000000000001
GPR24: 0000000000000003 0000000000000000 0000000000000001 ffffffffffffffb5
GPR28: c000000077ca2e80 0000000000000000 c00000000092af78 0000000000010000
NIP [c000000000038d60] .slice_get_unmapped_area+0x6c/0x4e0
LR [c00000000003945c] .hugetlb_get_unmapped_area+0x6c/0x80
Call Trace:
[c000000077e7bbc0] [c00000000003945c] .hugetlb_get_unmapped_area+0x6c/0x80
[c000000077e7bc30] [c000000000107e30] .get_unmapped_area+0x64/0xd8
[c000000077e7bcb0] [c00000000010b140] .do_mmap_pgoff+0x140/0x420
[c000000077e7bd80] [c00000000000bf5c] .sys_mmap+0xc4/0x140
[c000000077e7be30] [c0000000000086b4] syscall_exit+0x0/0x40
Instruction dump:
fac1ffb0 fae1ffb8 fb01ffc0 fb21ffc8 fb41ffd0 fb61ffd8 fb81ffe0 fbc1fff0
fbe1fff8 f821fef1 f8c10158 f8e10160 <7d49002e> f9010168 e92d01b0 eb4902b0
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
VMI initialiation can relocate the fixmap, causing early_ioremap to
malfunction if it is initialized before the relocation. To fix this,
VMI activation is split into two phases; the detection, which must
happen before setting up ioremap, and the activation, which must happen
after parsing early boot parameters.
This fixes a crash on boot when VMI is enabled under VMware.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 5b7dba4ff8, which
caused a regression in hibernate, reported by and bisected by Fabio
Comolli.
This revert fixes
http://bugzilla.kernel.org/show_bug.cgi?id=12155http://bugzilla.kernel.org/show_bug.cgi?id=12149
Bisected-by: Fabio Comolli <fabio.comolli@gmail.com>
Requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An example calling sequence which we did see:
copy_user_highpage -> kmap_atomic -> flush_tlb_page -> _tlbil_va
We got interrupted after setting up the MAS registers before the
tlbwe and the interrupt handler that caused the interrupt also did
a kmap_atomic (ide code) and thus on returning from the interrupt
the MAS registers no longer contained the proper values.
Since we dont save/restore MAS registers for normal interrupts we
need to disable interrupts in _tlbil_va to ensure atomicity.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the console, there is a 1:1 mapping of glyphs which cannot be found
in the current font. This seems to be meant as a kind of 'emergency
fallback' for fonts without unicode mapping which otherwise would
display nothing readable on the screen.
At the moment it affects all chars for which no substitution character
is defined. In particular this means that for all chars (>= 128) where
there is no iso88591-1/unicode character (e.g. control character area)
you'll get the very strange 1:1 mapping of the (cp437) graphics card
glyphs.
I'm pretty sure that the 1:1 mapping should only affect strict ASCII
code characters, i.e. chars < 128.
The patch limits the mapping as it probably was meant anyway.
Signed-off-by: Ingo Brueckl <ib@wupperonline.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Egmont Koblinger <egmont@uhulinux.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a major bug in the cp437 to unicode translation table. Char
0x7c is mapped to U+00a5 which is the Yen sign and wrong. The right
mapping is U+00a6 (broken bar).
Furthermore, a mapping for U+00b4 (a widely used character) is missing
even though easily possible.
The patch fixes these, as well as it provides a few other useful
mappings.
The changes are as follows:
0x0f (enhancement) enables a sort of currency symbol
0x27 (bug) enables a sort of acute accent which is a widely used character
0x44 (enhancement) enables a sort of icelandic capital letter eth
0x7c (major bug) corrects mapping
0xeb (enhancement) enables a sort of icelandic small letter eth
0xee (enhancement) enables a sort of math 'element of'
Signed-off-by: Ingo Brueckl <ib@wupperonline.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_free_noncoherent() and dma_free_coherent() are missing calls to
plat_unmap_dma_mem(). This patch adds them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The header path in the help text for the RUNTIME_DEBUG config option is
obsolete and needs to be updated to match the new location of
architecture-specific header files. While at it, fix the spelling mistake.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For MIPS R2, use the EI and DI instructions to enable and disable
interrupts.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The test-unit-ready portion of this patch was causing boots to fail on
my test machine (as in http://lkml.org/lkml/2008/12/5/161). With this
patch in place, the system is booting reliably.
Mike Anderson found the same problem in the hp_hw_start_stop code,
and I applied the same solution in cdrom_read_cdda_bpc.
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The cuboot-acadia.c wrapper can cause assembler errors on some
toolchains due to the lack of the proper BOOTCFLAGS. This adds
the proper flags for the file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
tmp is used as host-endian and is loaded from a be64, fix the cast and the
endian accessor used.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This reverts commit b1ee26bab1, along with
the "fixes" for it that all just caused problems:
- c4c6fa9891 "radeonfb: fix problem with
color expansion & alignment"
- f3179748a1 "radeonfb: Disable new color
expand acceleration unless explicitely enabled"
because even when disabled, it breaks for people. See
http://bugzilla.kernel.org/show_bug.cgi?id=12191
for the latest example.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: James Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lee Schermerhorn noticed yesterday that I broke the mapping_writably_mapped
test in 2.6.7! Bad bad bug, good good find.
The i_mmap_writable count must be incremented for VM_SHARED (just as
i_writecount is for VM_DENYWRITE, but while holding the i_mmap_lock)
when dup_mmap() copies the vma for fork: it has its own more optimal
version of __vma_link_file(), and I missed this out. So the count
was later going down to 0 (dangerous) when one end unmapped, then
wrapping negative (inefficient) when the other end unmapped.
The only impact on x86 would have been that setting a mandatory lock on
a file which has at some time been opened O_RDWR and mapped MAP_SHARED
(but not necessarily PROT_WRITE) across a fork, might fail with -EAGAIN
when it should succeed, or succeed when it should fail.
But those architectures which rely on flush_dcache_page() to flush
userspace modifications back into the page before the kernel reads it,
may in some cases have skipped the flush after such a fork - though any
repetitive test will soon wrap the count negative, in which case it will
flush_dcache_page() unnecessarily.
Fix would be a two-liner, but mapping variable added, and comment moved.
Reported-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last patch to lib/idr.c caused a bug if idr_get_new_above() was
called on an empty idr.
Usually, nodes stay on the same layer. New layers are added to the top
of the tree.
The exception is idr_get_new_above() on an empty tree: In this case, the
new root node is first added on layer 0, then moved upwards. p->layer
was not updated.
As usual: You shall never rely on the source code comments, they will
only mislead you.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Give the correct size when reserving the interrupt vector table. It should be
a page not a single byte.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix __put_user_asm8() by jumping to the end label (3:) from the exception
handler, rather than jumping back to retry the second store instruction (label
2:).
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the preemption resume_kernel() routine by inverting the test to see
whether interrupts are off (IM7 is all enabled, not all disabled).
Furthermore, interrupts should be disabled on entry to resume_kernel() so that
they're correctly set for jumping to restore_all() and doing the need
reschedule test.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Discard low-prioriy Tx interrupts when closing an MN10300 on-chip serial port.
The MN10300 on-chip serial port uses three interrupts to manage its serial
ports:
(1) A very high priority interrupt that drives virtual DMA for Rx.
(2) A very high priority interrupt that drives virtual DMA for Tx.
(3) A normal priority virtual interrupt that does the normal UART interrupt
stuff and is shared between Rx and Tx.
mn10300_serial_stop_tx() only disables the high priority Tx interrupt. It
doesn't also disable the normal priority one because it is shared with Rx.
However, the high priority interrupt may interrupt local_irq_disabled()
sections, and so may have queued up a low priority virtual interrupt whilst the
UART driver is asking for the Tx interrupt to be disabled.
The result of this can be an oops when we try to process the interrupt in
mn10300_serial_transmit_interrupt() as port->uart.info and port->uart.info->tty
may have gone away.
To deal with this, if either of those pointers is NULL, we make sure the
high-priority Tx interrupt is disabled and discard the interrupt. The low
priority interrupt is disabled by the mn10300_serial_pic irq_chip table.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include the linux/page.h header into the MN10300 kernel linker script thus
allowing us to use PAGE_SIZE macro instead of a numeric constant.
Also use the PERCPU macro instead of an explicit section definition.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCIe: ASPM: Break out of endless loop waiting for PCI config bits to switch
PCI: stop leaking 'slot_name' in pci_create_slot
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] SN: prevent IRQ retargetting in request_irq()
[IA64] Fix section mismatch ioc3uart_init()/ioc3uart_submodule
[IA64] Clear up section mismatch for ioc4_ide_attach_one.
[IA64] Clear up section mismatch with arch_unregister_cpu()
[IA64] Clear up section mismatch for sn_check_wars.
[IA64] Updated the generic_defconfig to work with the 2.6.28-rc7 kernel.
[IA64] Fix GRU compile error w/o CONFIG_HUGETLB_PAGE
[IA64] eliminate NULL test and memset after alloc_bootmem
[IA64] remove BUILD_BUG_ON from paravirt_getreg()
The pktcdvd created class devices only export some sysfs files,
but have no char dev_t registered in the driver.
At class device creation time they copy the dev_t value of the
block device to the char device, wich will register a new char
device in the driver core and userspace, with a conflicting dev_t
value.
In many cases the class devices dev_t just points to a random
USB device. This fixes the sysfs "duplicate entry" errors.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparc64:
drivers/video/mb862xx/mb862xxfb.c:929: warning: long long unsigned int format, resource_size_t arg (arg 4)
drivers/video/mb862xx/mb862xxfb.c:931: warning: long long unsigned int format, resource_size_t arg (arg 4)
We don't know what type the architecture uses to implement u64, hence they
cannot be printed.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matteo Fortini <m.fortini@selcomgroup.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Miles Lane tailing /sys files hit a BUG which Pekka Enberg has tracked
to my 966c8c12dc sprint_symbol(): use
less stack exposing a bug in slub's list_locations() -
kallsyms_lookup() writes a 0 to namebuf[KSYM_NAME_LEN-1], but that was
beyond the end of page provided.
The 100 slop which list_locations() allows at end of page looks roughly
enough for all the other stuff it might print after the symbol before
it checks again: break out KSYM_SYMBOL_LEN earlier than before.
Latencytop and ftrace and are using KSYM_NAME_LEN buffers where they
need KSYM_SYMBOL_LEN buffers, and vmallocinfo a 2*KSYM_NAME_LEN buffer
where it wants a KSYM_SYMBOL_LEN buffer: fix those before anyone copies
them.
[akpm@linux-foundation.org: ftrace.h needs module.h]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc Miles Lane <miles.lane@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On umount two event will be dispatched to watcher:
1: inotify_dev_queue_event(.., IN_UNMOUNT,..)
2: remove_watch(watch, dev)
->inotify_dev_queue_event(.., IN_IGNORED, ..)
But if watcher has IN_ONESHOT bit set then the watcher will be released
inside first event. Which result in accessing invalid object later. IMHO
it is not pure regression. This bug wasn't triggered while initial
inotify interface testing phase because of another bug in IN_ONESHOT
handling logic :)
commit ac74c00e49
Author: Ulisses Furquim <ulissesf@gmail.com>
Date: Fri Feb 8 04:18:16 2008 -0800
inotify: fix check for one-shot watches before destroying them
As the IN_ONESHOT bit is never set when an event is sent we must check it
in the watch's mask and not in the event's mask.
TESTCASE:
mkdir mnt
mount -ttmpfs none mnt
mkdir mnt/d
./inotify mnt/d&
umount mnt ## << lockup or crash here
TESTSOURCE:
/* gcc -oinotify inotify.c */
#include <stdio.h>
#include <stdlib.h>
#include <sys/inotify.h>
int main(int argc, char **argv)
{
char buf[1024];
struct inotify_event *ie;
char *p;
int i;
ssize_t l;
p = argv[1];
i = inotify_init();
inotify_add_watch(i, p, ~0);
l = read(i, buf, sizeof(buf));
printf("read %d bytes\n", l);
ie = (struct inotify_event *) buf;
printf("event mask: %d\n", ie->mask);
return 0;
}
Signed-off-by: Dmitri Monakhov <dmonakhov@openvz.org>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Robert Love <rlove@google.com>
Cc: Ulisses Furquim <ulissesf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atomic_long_xchg() is not correctly defined for 32bit arches.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 2f007e74bb, do_pages_stat()
gets the page address from user-space and puts the corresponding status
back while holding the mmap_sem for read. There is no need to hold
mmap_sem there while some page-faults may occur.
This patch adds a temporary address and status buffer so as to only
hold mmap_sem while working on these kernel buffers. This is
implemented by extracting do_pages_stat_array() out of do_pages_stat().
Signed-off-by: Brice Goglin <Brice.Goglin@inria.fr>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The large pages fix from bcf8039ed4 broke 32-bit pagemap by pulling the
pagemap entry code out into a function with the wrong return type.
Pagemap entries are 64 bits on all systems and unsigned long is only 32
bits on 32-bit systems.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Reported-by: Doug Graham <dgraham@nortel.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a total bootup freeze on ia64.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Li Zefan <lizf@cn.fujitsu.com>
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build error when RTC_INTF_DEV=n:
drivers/rtc/rtc-twl4030.c:402: error: 'twl4030_rtc_ioctl' undeclared here (not in a function)
make[3]: *** [drivers/rtc/rtc-twl4030.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a call to cancel_work_sync() in fbcon_exit() to cancel any pending
work in the fbcon workqueue.
The current implementation of fbcon_exit() sets the fbcon workqueue
function info->queue.func to NULL, but does not assure that there is no
work pending when it does so. On occasion, depending on system timing,
there will still be pending work in the queue when fbcon_exit() is
called. This results in a null pointer deference when run_workqueue()
tries to call the queue's work function.
Fixes errors on shutdown similar to these:
Console: switching to colour dummy device 80x25
Unable to handle kernel paging request for data at address 0x00000000
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, lru_add_drain_all() has two version.
(1) use schedule_on_each_cpu()
(2) don't use schedule_on_each_cpu()
Gerald Schaefer reported it doesn't work well on SMP (not NUMA) S390
machine.
offline_pages() calls lru_add_drain_all() followed by drain_all_pages().
While drain_all_pages() works on each cpu, lru_add_drain_all() only runs
on the current cpu for architectures w/o CONFIG_NUMA. This let us run
into the BUG_ON(!PageBuddy(page)) in __offline_isolated_pages() during
memory hotplug stress test on s390. The page in question was still on the
pcp list, because of a race with lru_add_drain_all() and drain_all_pages()
on different cpus.
Actually, Almost machine has CONFIG_UNEVICTABLE_LRU=y. Then almost machine use
(1) version lru_add_drain_all although the machine is UP.
Then this ifdef is not valueable.
simple removing is better.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert
commit e8ced39d5e
Author: Mingming Cao <cmm@us.ibm.com>
Date: Fri Jul 11 19:27:31 2008 -0400
percpu_counter: new function percpu_counter_sum_and_set
As described in
revert "percpu counter: clean up percpu_counter_sum_and_set()"
the new percpu_counter_sum_and_set() is racy against updates to the
cpu-local accumulators on other CPUs. Revert that change.
This means that ext4 will be slow again. But correct.
Reported-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mingming Cao <cmm@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann
Dave Hansen
Brian King
Linus Torvalds
Zachary Amsden
Kumar Gala
Ingo Brueckl
David Daney
Dmitri Vorobiev
Alan D. Brunelle
Josh Boyer
Harvey Harrison
Hugh Dickins
Manfred Spraul
Akira Takeuchi
Cyrill Gorcunov
Kay Sievers
Andrew Morton
Dmitri Monakhov
Eric Dumazet
Brice Goglin
Balaji Rao
Matt Mackall
KAMEZAWA Hiroyuki
Randy Dunlap
Geoff Levand
KOSAKI Motohiro