The L3 cache remapping is stored as u32 elements, and we should ensure
that the user only supplies complete slice information(u32).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004105958.1741-1-chris@chris-wilson.co.uk
On platfroms with gen10+ display, driver must set the enable bit of
AUDIO_PIN_BUF_CTL register before transactions with the HDA controller
can proceed. Add setting this bit to the audio power up sequence.
Failing to do this resulted in errors during display audio codec probe,
and failures during resume from suspend.
Note: We may also need to disable the bit afterwards, but there are
still unresolved issues with that.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111214
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003085531.30990-1-kai.vehmanen@linux.intel.com
Add aux_busy_last_status to intel_dp. Don't bother with initializing to
all ones; the only difference is potentially missing logging for one
error case if the readout is all zeros.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002144138.7917-1-jani.nikula@intel.com
The Thunderbolt PLL divider values on TGL differ from the ICL ones,
update the PLL parameter calculation function accordingly.
Bspec: 49204
v2:
- Remove unused refclk config. (José)
Cc: Jose Souza <jose.souza@intel.com>
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Westerberg <mika.westerberg@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jose Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002204108.32242-1-imre.deak@intel.com
If execlists's lite-restore is based on the common GEM context tag
rather than the per-intel_context LRCA, then a context switch between
two intel_contexts on the same engine derived from the same GEM context
will perform a lite-restore instead of a full context switch. We can
exploit this by poisoning the ringbuffer of the first context and trying
to trick a simple RING_TAIL update (i.e. lite-restore)
v2: Also check what happens if preempt ce[0] with ce[1] (both instances
on the same engine from the same parent context) [Tvrtko]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002183459.26614-1-chris@chris-wilson.co.uk
All the MG registers is based on the tc_port not port, so
MG_PHY_PORT_LN() was subtracting port and PORT_C what is very
fragile.
So replacing port to tc_port in all MG register macros and users
like we have for DKL.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001193729.123736-1-jose.souza@intel.com
For selftests, we desire repeatability and so prefer using a prng with
known seed over true randomness. Extract random_offset() as a selftest
utility that can take the prng state.
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002122430.23205-1-chris@chris-wilson.co.uk
I forgot to update the g4x sprite scaling stride check when GTT
remapping was introduced. The stride of the original framebuffer
is irrelevant when remapping is used and instead we want to check
the stride of the remapped view.
Also drop the duplicate width_bytes check. We already check that
a few lines earlier.
Fixes: df79cf4419 ("drm/i915: Store the final plane stride in plane_state")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190930183045.662-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Drop the tv_mode NULL check since intel_tv_mode_find() never
actually returns NULL, and flip the condition around so that
the MODE_OK case is at the end, which is customary to all
the other .mode_valid() implementations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001154629.11063-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
When adding the max plane size checks to the .mode_valid() hooks
I naturally forgot about MST. Take care of that one as well.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Sean Paul <sean@poorly.run>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 2d20411e25 ("drm/i915: Don't advertise modes that exceed the max plane size")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001154629.11063-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Split out the code related to vga client and vgaarb all over the place
into new intel_vga.[ch]. No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191001152506.7854-1-jani.nikula@intel.com
Unwedging the GPU requires a successful GPU reset before we restore the
default submission, or else we may see residual context switch events
that we were not expecting.
v2: Pull in the special-case reset_clobbers_display, and explain why it
should be safe in the context of unwedging.
v3: Just forget all about resets before unwedging if it will clobber the
display; risk it all.
Reported-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20190927160335.10622-1-chris@chris-wilson.co.uk
We currently test context switching on each engine as a basic stress
test (just verifying that nothing explodes if we execute 2 requests from
different contexts sequentially). What we have not tested is what
happens if we try and do so on all available engines simultaneously,
putting our SW and the HW under the maximal stress.
v2: Clone the set of engines from the first context into the secondary
contexts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190930144919.27992-1-chris@chris-wilson.co.uk
On systems that have no runtime-pm, we mark the wakeref as being -1. We
therefore cannot use that value for the mock-gt indicator, so opt for
-ENODEV instead. The wakeref should never be an error value -- one
hopes!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927211749.2181-2-chris@chris-wilson.co.uk
As we execute GPU resets on a gt/ basis, and use the intel_gt as the
primary for all other reset functions, also use it for the has-reset?
predicates. Gradually simplifying the churn of pointers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927211749.2181-1-chris@chris-wilson.co.uk
Now that TC support was added, initialize DDIs.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-4-jose.souza@intel.com
Link training is failling when running link at 2.7GHz and 1.62GHz and
following BSpec pll algorithm.
Comparing the values calculated and the ones from the reference table
it looks like MG_CLKTOP2_CORECLKCTL1_A_DIVRATIO should not always set
to 5. For DP ports ICL mg pll algorithm sets it to 10 or 5 based on
div2 value, that matches with dkl hardcoded table.
So implementing this way as it proved to work in HW and leaving a
comment so we know why it do not match BSpec.
v4:
Using the same is_dp check as ICL, need testing on HDMI over tc port
Issue reported on BSpec 49204.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-3-jose.souza@intel.com
Added DKL Phy sequences and helpers functions to program voltage
swing, clock gating and dp mode.
It is not written in DP enabling sequence but "PHY Clockgating
programming" states that clock gating should be enabled after the
link training but doing so causes all the following trainings to fail
so not enabling it for.
v2:
Setting the right HIP_INDEX_REG bits (José)
v3:
Adding the meaning of each column of tgl_dkl_phy_ddi_translations
Adding if gen >= 12 on intel_ddi_hdmi_level() and
intel_ddi_pre_enable_hdmi() instead of reuse part of gen >= 11 if
v4:
Moved the DP_MODE lane programing to another patch as ICL also
needed it
Sharing icl_phy_set_clock_gating() and icl_program_mg_dp_mode() with
TGL as bits and programing as now it almost identical to ICL
BSpec: 49292
BSpec: 49190
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-2-jose.souza@intel.com
BSpec was updated(r146548) with a new MG_DP_MODE Programming table,
now taking in consideration the pin assignment and allowing us to
optimize power by shutting down available but not needed lanes.
It was tested on ICL and TGL, with adaptors that used pin assignment
C and B, reversing the connector and going to different modes testing
the not needed lane shutdown.
v5:
Using crtc_state->lane_count instead of dp.lane_count
BSpec: 21735
BSpec: 49292
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-1-jose.souza@intel.com
We have a new version of DMC for ICL - v1.09.
This version adds the Half Refresh Rate capability
into DMC.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925201250.18136-1-daniele.ceraolospurio@intel.com
The HuC FW has silently switched to encoding the version the same way as
the GuC FW does, i.e. major.minor.patch instead of just major.minor. All
the current blobs follow the new scheme, but since minor and patch are
both zero there is no difference in the end results and we happily load
them. New binaries, however, will have non-zero values in there, so we
need to make sure to parse them correctly.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Acked-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925222121.4000-1-daniele.ceraolospurio@intel.com
We can use it in i915 for updating parts of unmasked registers from
within a batch. We're also adding Gen8+ versions of CS_GPR registers
(aka MI_MATH_REG in the coprocessor).
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926100635.9416-4-michal.winiarski@intel.com
Insert structure members names into their descriptions to follow
kernel-doc format.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Anna Karas <anna.karas@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926122158.13028-1-anna.karas@intel.com
The function intel_engine_breadcrumbs_irq() is always invoked from an interrupt
handler and for that reason it invokes (as an optimisation) only spin_lock()
for locking assuming that the interrupts are already disabled. The
function intel_engine_signal_breadcrumbs() is provided to disable
interrupts while the former function is invoked so that assumption is
also true for callers from preemptible context.
On PREEMPT_RT local_irq_disable() really disables interrupts and this
forbids to invoke spin_lock() which becomes a sleeping spinlock.
This is also problematic with `threadirqs' in conjunction with
irq_work. With force threading the interrupt handler, the handler is
invoked with disabled BH but with interrupts enabled. This is okay and
the lock itself is never acquired in IRQ context. This changes with
irq_work (signal_irq_work()) which _still_ invokes
intel_engine_breadcrumbs_irq() from IRQ context. Lockdep should see this
and complain.
Acquire the locks in intel_engine_breadcrumbs_irq() with _irqsave()
suffix and let all callers invoke intel_engine_breadcrumbs_irq()
directly instead using intel_engine_signal_breadcrumbs().
Reported-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926105644.16703-2-bigeasy@linutronix.de
The lockdep_assert_irqs_disabled() check is needless. The previous
lockdep_assert_held() check ensures that the lock is acquired and while
the lock is acquired lockdep also prints a warning if the interrupts are
not disabled if they have to be.
These IRQ-off asserts trigger on PREEMPT_RT because the locks become
sleeping locks and do not really disable interrupts.
Remove lockdep_assert_irqs_disabled().
Reported-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926105644.16703-3-bigeasy@linutronix.de
Default length value of MI_LOAD_REGISTER_REG is 1.
Also move it out of cmd-parser-only registers since we're going to use
it in i915.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926133142.2838-3-chris@chris-wilson.co.uk
Some of our commands (MI_FLUSH_DW / PIPE_CONTROL) require a post-sync write
operation to be performed. Currently we're using dedicated VMA for
PIPE_CONTROL and global HWSP for MI_FLUSH_DW.
On execlists platforms, each of our contexts has an area that can be
used as scratch space. Let's use that instead.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926133142.2838-2-chris@chris-wilson.co.uk
We're currently using scratch presence as a way of identifying that we
entered wedged state at driver initialization time.
Let's use a separate flag rather than rely on scratch.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926133142.2838-1-chris@chris-wilson.co.uk
According to the bspec, GLK/CNL have a smaller small joiner RAM buffer
than ICL+. This feels like something that could easily change again on
future platforms, so let's just add a function to return the proper
per-platform buffer size. That may also slightly simplify the upcoming
bigjoiner enabling.
Since we have to change intel_dp_dsc_get_output_bpp()'s signature to
pass the dev_priv down for the platform check, let's take the
opportunity to also make that function static since it isn't used
outside the intel_dp file.
v2: Minor rebase on top of Maarten's changes.
Bspec: 20388
Bspec: 49259
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925234542.24289-1-matthew.d.roper@intel.com
The memory type values have changed in TGL, so we need to translate them
differently than ICL. While we're moving it, fix up the ICL translation
for LPDDR4.
BSpec: 53998
v2: Fix up ICL LPDDR4 entry (Ville); Drop unused values from TGL (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924222829.13142-1-james.ausmus@intel.com
TGL added 2 more TC ports that currently are not being handled by
icl_pll_to_ddi_clk_sel(), so adding those.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-6-jose.souza@intel.com
Extending ICL mg calculations to also support dkl calculations.
v3:
Fixing iref_trim calculation for 38400 refclock
BSpec: 49204
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-5-jose.souza@intel.com
The final save operation into pll_state of the calculations done will
be different for DKL PHY. Prepare for that by reindenting code so it's
easier to check for correctness. This one has no change in behavior.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-4-jose.souza@intel.com
Chris Wilson
Kai Vehmanen
Jani Nikula
Imre Deak
José Roberto de Souza
Ville Syrjälä
Srinivasan S
Matthew Auld
Lucas De Marchi
Clinton A Taylor
Anusha Srivatsa
Daniele Ceraolo Spurio
Joonas Lahtinen
Andi Shyti
Michał Winiarski
Anna Karas
Sebastian Andrzej Siewior
Matt Roper
James Ausmus