[ Upstream commit e5992f373c ]
Commit 32f6e5da83 ("selftests/ftrace: Add kprobe profile testcase")
added a new kprobes testcase, but has a description which does not
describe what the test case is doing and is duplicating the description
of another test case.
Therefore change the test case description, so it is unique and then
allows easily to tell which test case actually passed or failed.
Reported-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab39d6988d ]
The gpio-aspeed-sgpio driver implements an irq_chip which need to be
invoked from hardirq context. Since spin_lock() can sleep with
PREEMPT_RT, it is no longer legal to invoke it while interrupts are
disabled.
This also causes lockdep to complain about:
[ 25.919465] [ BUG: Invalid wait context ]
because aspeed_sgpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61a7904b6a ]
The gpio-aspeed driver implements an irq_chip which need to be invoked
from hardirq context. Since spin_lock() can sleep with PREEMPT_RT, it is
no longer legal to invoke it while interrupts are disabled.
This also causes lockdep to complain about:
[ 0.649797] [ BUG: Invalid wait context ]
because aspeed_gpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f20f94f7f5 ]
The PHY settings table is supposed to be sorted by descending match
priority - in other words, earlier entries are preferred over later
entries.
The order of 1000baseKX/Full and 1000baseT/Full is such that we
prefer 1000baseKX/Full over 1000baseT/Full, but 1000baseKX/Full is
a lot rarer than 1000baseT/Full, and thus is much less likely to
be preferred.
This causes phylink problems - it means a fixed link specifying a
speed of 1G and full duplex gets an ethtool linkmode of 1000baseKX/Full
rather than 1000baseT/Full as would be expected - and since we offer
userspace a software emulation of a conventional copper PHY, we want
to offer copper modes in preference to anything else. However, we do
still want to allow the rarer modes as well.
Hence, let's reorder these two modes to prefer copper.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1muvFO-00F6jY-1K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7dac08341 ]
When updating Rx and Tx queue kobjects, the queue count should always be
updated to match the queue kobjects count. This was not done in the net
device unregistration path, fix it. Tracking all queue count updates
will allow in a following up patch to detect illegal updates.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8a91863eb ]
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210505085806.11474-1-s.gottschall@dd-wrt.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ff7c9f9d7 ]
If we use the module stall_cpu option, we may get a soft lockup warning
in case we also don't pass the stall_cpu_block option.
Introduce the stall_no_softlockup option to avoid a soft lockup on
cpu stall even if we don't use the stall_cpu_block option.
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e967c137d ]
When scheduling a session protection the id is saved but
then it may be cleared when calling iwl_mvm_te_clear_data
(if a previous session protection is currently active).
Fix it by saving the id after calling iwl_mvm_te_clear_data.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204130722.b0743a588d14.I098fef6677d0dab3ef1b6183ed206a10bab01eb2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db66abeea3 ]
If userspace installs a lot of multicast groups very quickly, then
we may run out of command queue space as we send the updates in an
asynchronous fashion (due to locking concerns), and the CPU can
create them faster than the firmware can process them. This is true
even when mac80211 has a work struct that gets scheduled.
Fix this by synchronizing with the firmware after sending all those
commands - outside of the iteration we can send a synchronous echo
command that just has the effect of the CPU waiting for the prior
asynchronous commands to finish. This also will cause fewer of the
commands to be sent to the firmware overall, because the work will
only run once when rescheduled multiple times while it's running.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213649
Suggested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reported-by: Maximilian Ernestus <maximilian@ernestus.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211204083238.51aea5b79ea4.I88a44798efda16e9fe480fb3e94224931d311b29@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82ce79391d ]
The binding node names for the thermal zones are not successfully
validated by the dt-schemas.
Fix the validation by changing from sensor-thermalN or thermal-sensor-N
to sensorN-thermal. Provide node labels of the form sensorN_thermal to
ensure consistency with the other platform implementations.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211104224033.3997504-1-kieran.bingham+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3380cac0c ]
If protocol tunnels are already up when the driver is loaded, for
instance if the boot firmware implements connection manager of its own,
runtime PM reference count of the consumer devices behind the tunnel
might have been increased already before the device link is created but
the supplier device runtime PM reference count is not. This leads to a
situation where the supplier (the Thunderbolt driver) can runtime
suspend even if it should not because the corresponding protocol tunnel
needs to be up causing the devices to be removed from the corresponding
native bus.
Prevent this from happening by making both sides of the link runtime PM
active briefly. The pm_runtime_put() for the consumer (PCIe
root/downstream port, xHCI) then allows it to runtime suspend again but
keeps the supplier runtime resumed the whole time it is runtime active.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2ab06d7c4 ]
Using stack-allocated pointers for USB message data don't work.
This driver is almost OK with that, except for the I2C read
logic.
Fix it by using a temporary read buffer, just like on all other
calls to m920x_read().
Link: https://lore.kernel.org/all/ccc99e48-de4f-045e-0fe4-61e3118e3f74@mida.se/
Reported-by: rkardell@mida.se
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 348df80353 ]
In hexium_attach(dev, info), saa7146_vv_init() is called to allocate
a new memory for dev->vv_data. In hexium_detach(), saa7146_vv_release()
will be called and there is a dereference of dev->vv_data in
saa7146_vv_release(), which could lead to a NULL pointer dereference
on failure of saa7146_vv_init() according to the following logic.
Both hexium_attach() and hexium_detach() are callback functions of
the variable 'extension', so there exists a possible call chain directly
from hexium_attach() to hexium_detach():
hexium_attach(dev, info) -- fail to alloc memory to dev->vv_data
| in saa7146_vv_init().
|
|
hexium_detach() -- a dereference of dev->vv_data in saa7146_vv_release()
Fix this bug by adding a check of saa7146_vv_init().
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_VIDEO_HEXIUM_ORION=m show no new warnings,
and our static analyzer no longer warns about this code.
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da6911f330 ]
This change fixes two issues with the size constraints for buffers.
- There is no width alignment constraint for RGB formats. Prior to this
change they were treated as YUV and as a result were more restricted
than needed. Add a new check to differentiate between the two.
- The minimum width and height supported is 5x2, not 2x4, this is an
artifact from the driver's soc-camera days. Fix this incorrect
assumption.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8ed7d2f61 ]
Some uvc devices appear to require the maximum allowed USB timeout
for GET_CUR/SET_CUR requests.
So lets just bump the UVC control timeout to 5 seconds which is the
same as the usb ctrl get/set defaults:
USB_CTRL_GET_TIMEOUT 5000
USB_CTRL_SET_TIMEOUT 5000
It fixes the following runtime warnings:
Failed to query (GET_CUR) UVC control 11 on unit 2: -110 (exp. 1).
Failed to query (SET_CUR) UVC control 3 on unit 2: -110 (exp. 2).
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0ce591dc9 ]
When the CMM is enabled, an offset of 25 pixels must be subtracted from
the HDS (horizontal display start) and HDE (horizontal display end)
registers. Fix the timings calculation, and take this into account in
the mode validation.
This fixes a visible horizontal offset in the image with VGA monitors.
HDMI monitors seem to be generally more tolerant to incorrect timings,
but may be affected too.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71d5049b05 ]
Move the switching code into a function so that it can be re-used and
add a global TLB flush. This makes sure that usage of memory which is
not mapped in the trampoline page-table is reliably caught.
Also move the clearing of CR4.PCIDE before the CR3 switch because the
cr4_clear_bits() function will access data not mapped into the
trampoline page-table.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211202153226.22946-4-joro@8bytes.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57d2dbf710 ]
The GPD win and its sibling the GPD pocket (99% the same electronics in a
different case) use a PCI wifi card. But the ACPI tables on both variants
contain a bug where the SDIO MMC controller for SDIO wifi cards is enabled
despite this. This SDIO MMC controller has a PCI0.SDHB.BRC1 child-device
which _PS3 method sets a GPIO causing the PCI wifi card to turn off.
At the moment there is a pretty ugly kludge in the sdhci-acpi.c code,
just to work around the bug in the DSDT of this single design. This can
be solved cleaner/simply with a quirk overriding the _STA return of the
broken PCI0.SDHB.BRC1 PCI0.SDHB.BRC1 child with a status value of 0,
so that its power_manageable flag gets cleared, avoiding this problem.
Note that even though it is not used, the _STA method for the MMC
controller is deliberately not overridden. If the status of the MMC
controller were forced to 0 it would never get suspended, which would
cause these mini-laptops to not reach S0i3 level when suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba46e42e92 ]
Not all ACPI-devices have a HID + UID, allow specifying quirks for
acpi_device_override_status() by path too.
Note this moves the path/HID+UID check to after the CPU + DMI checks
since the path lookup is somewhat costly.
This way this lookup is only done on devices where the other checks
match.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a68b346a2 ]
Currently, acpi_bus_get_status() calls acpi_device_always_present() to
allow platform quirks to override the _STA return to report that a
device is present (status = ACPI_STA_DEFAULT) independent of the _STA
return.
In some cases it might also be useful to have the opposite functionality
and have a platform quirk which marks a device as not present (status = 0)
to work around ACPI table bugs.
Change acpi_device_always_present() into a more generic
acpi_device_override_status() function to allow this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d431dfb764 ]
It turns out that there is a WMI object which controls the PWM2 device
used for the keyboard backlight and that WMI object also provides some
other useful functionality.
The upcoming lenovo-yogabook-wmi driver will offer both backlight
control and the other functionality, so there no longer is a need
to have the lpss-pwm driver binding to PWM2 for backlight control;
and this is now actually undesirable because this will cause both
the WMI code and the lpss-pwm driver to poke at the same PWM
controller.
Drop the always-present quirk for the PWM2 ACPI-device, so that the
lpss-pwm controller will no longer bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6be23264b ]
For larger (bigger than a page) and noncontiguous mobs we have
to create page tables that allow the host to find the memory.
Those page tables just used regular system memory. Unfortunately
in TTM those BO's are not allowed to be busy thus can't be
fenced and we have to fence those bo's because we don't want
to destroy the page tables while the host is still executing
the command buffers which might be accessing them.
To solve it we introduce a new placement VMW_PL_SYSTEM which
is very similar to TTM_PL_SYSTEM except that it allows
fencing. This fixes kernel oops'es during unloading of the driver
(and pci hot remove/add) which were caused by busy BO's in
TTM_PL_SYSTEM being present in the delayed deletion list in
TTM (TTM_PL_SYSTEM manager is destroyed before the delayed
deletions are executed)
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105193845.258816-5-zackr@vmware.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b5f3b612 ]
The ttm mem global state was leaking if the vmwgfx driver load failed.
In case of a driver load failure we have to make sure we also release
the ttm mem global state.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105193845.258816-3-zackr@vmware.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a93789ae54 ]
Currently 'ar' reference is not added in skb_cb during
WMI mgmt tx. Though this is generally not used during tx completion
callbacks, on interface removal the remaining idr cleanup callback
uses the ar ptr from skb_cb from mgmt txmgmt_idr. Hence
fill them during tx call for proper usage.
Also free the skb which is missing currently in these
callbacks.
Crash_info:
[19282.489476] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[19282.489515] pgd = 91eb8000
[19282.496702] [00000000] *pgd=00000000
[19282.502524] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[19282.783728] PC is at ath11k_mac_vif_txmgmt_idr_remove+0x28/0xd8 [ath11k]
[19282.789170] LR is at idr_for_each+0xa0/0xc8
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637832614-13831-1-git-send-email-quic_srirrama@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1cb3476e4 ]
rsi_get_* functions rely on an offset variable from usb
input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000),
while 2-byte offset can be up to 0xFFFF. Thus a large offset
can cause out-of-bounds read.
The patch adds a bound checking condition when rcv_pkt_len is 0,
indicating it's USB. It's unclear whether this is triggerable
from other type of bus. The following check might help in that case.
offset > rcv_pkt_len - FRAME_DESC_SZ
The bug is trigerrable with conpromised/malfunctioning USB devices.
I tested the patch with the crashing input and got no more bug report.
Attached is the KASAN report from fuzzing.
BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x]
Read of size 2 at addr ffff888019439fdb by task RX-Thread/227
CPU: 0 PID: 227 Comm: RX-Thread Not tainted 5.6.0 #66
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
__kasan_report.cold+0x37/0x7c
? rsi_read_pkt+0x42e/0x500 [rsi_91x]
kasan_report+0xe/0x20
rsi_read_pkt+0x42e/0x500 [rsi_91x]
rsi_usb_rx_thread+0x1b1/0x2fc [rsi_usb]
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
? _raw_spin_lock_irqsave+0x7b/0xd0
? _raw_spin_trylock_bh+0x120/0x120
? __wake_up_common+0x10b/0x520
? rsi_probe+0x16a0/0x16a0 [rsi_usb]
kthread+0x2b5/0x3b0
? kthread_create_on_node+0xd0/0xd0
ret_from_fork+0x22/0x40
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxXS4wgu2OsmlVv@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b07e3c6ebc ]
When freeing rx_cb->rx_skb, the pointer is not set to NULL,
a later rsi_rx_done_handler call will try to read the freed
address.
This bug will very likley lead to double free, although
detected early as use-after-free bug.
The bug is triggerable with a compromised/malfunctional usb
device. After applying the patch, the same input no longer
triggers the use-after-free.
Attached is the kasan report from fuzzing.
BUG: KASAN: use-after-free in rsi_rx_done_handler+0x354/0x430 [rsi_usb]
Read of size 4 at addr ffff8880188e5930 by task modprobe/231
Call Trace:
<IRQ>
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
__kasan_report.cold+0x37/0x7c
? dma_direct_unmap_page+0x90/0x110
? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
kasan_report+0xe/0x20
rsi_rx_done_handler+0x354/0x430 [rsi_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __usb_hcd_giveback_urb+0x380/0x380
? apic_timer_interrupt+0xa/0x20
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
? handle_irq_event+0xcd/0x157
? handle_edge_irq+0x1eb/0x7b0
irq_exit+0x114/0x140
do_IRQ+0x91/0x1e0
common_interrupt+0xf/0xf
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxQL/vIiYcZUu/j@10-18-43-117.dynapool.wireless.nyu.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04d80663f6 ]
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
<IRQ>
? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
skb_put.cold+0x24/0x24
mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 552d03a223 ]
The APT compares the current time stamp with a pre-set value. The
current code only considered the 4 LSB only. Yet, after reviews by
mathematicians of the user space Jitter RNG version >= 3.1.0, it was
concluded that the APT can be calculated on the 32 LSB of the time
delta. Thi change is applied to the kernel.
This fixes a bug where an AMD EPYC fails this test as its RDTSC value
contains zeros in the LSB. The most appropriate fix would have been to
apply a GCD calculation and divide the time stamp by the GCD. Yet, this
is a significant code change that will be considered for a future
update. Note, tests showed that constantly the GCD always was 32 on
these systems, i.e. the 5 LSB were always zero (thus failing the APT
since it only considered the 4 LSB for its calculation).
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1ee1c08fc ]
cl is freed on error of calling device_register, but this
object is return later, which will cause uaf issue. Fix it
by return NULL on error.
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdfd6ab8fd ]
If the IRQ is already in use, then acpi_dev_gpio_irq_get_by() really
should not change the type underneath the current owner.
I specifically hit an issue with this an a Chuwi Hi8 Super (CWI509) Bay
Trail tablet, when the Boot OS selection in the BIOS is set to Android.
In this case _STA for a MAX17047 ACPI I2C device wrongly returns 0xf and
the _CRS resources for this device include a GpioInt pointing to a GPIO
already in use by an _AEI handler, with a different type then specified
in the _CRS for the MAX17047 device. Leading to the acpi_dev_gpio_irq_get()
call done by the i2c-core-acpi.c code changing the type breaking the
_AEI handler.
Now this clearly is a bug in the DSDT of this tablet (in Android mode),
but in general calling irq_set_irq_type() on an IRQ which already is
in use seems like a bad idea.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 028e083832 ]
The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().
Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller. Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 274ab58dc2 ]
The others are superfluous with tty refcounting in place now. And they
are racy in fact:
* tty_port_initialized() reports false for a small moment after
interrupts are enabled.
* closing is 1 while the port is still alive.
The queues are flushed later during close anyway. So there is no need
for this special handling. Actually, the ISR should not flush the
queues. It should behave as every other driver, just queue the chars
into tty buffer and go on. But this will be changed later. There is
still a lot code depending on having tty in ISR (and not only tty_port).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1020d3cf4 ]
On an arm64 platform with the Spectrum ASIC, after loading and executing
a new kernel via kexec, the following trace [1] is observed. This seems
to be caused by the fact that the device is not properly shutdown before
executing the new kernel.
Fix this by implementing a shutdown method which mirrors the remove
method, as recommended by the kexec maintainer [2][3].
[1]
BUG: Bad page state in process devlink pfn:22f73d
page:fffffe00089dcf40 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x2ffff00000000000()
raw: 2ffff00000000000 0000000000000000 ffffffff089d0201 0000000000000000
raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount
Modules linked in:
CPU: 1 PID: 16346 Comm: devlink Tainted: G B 5.8.0-rc6-custom-273020-gac6b365b1bf5 #44
Hardware name: Marvell Armada 7040 TX4810M (DT)
Call trace:
dump_backtrace+0x0/0x1d0
show_stack+0x1c/0x28
dump_stack+0xbc/0x118
bad_page+0xcc/0xf8
check_free_page_bad+0x80/0x88
__free_pages_ok+0x3f8/0x418
__free_pages+0x38/0x60
kmem_freepages+0x200/0x2a8
slab_destroy+0x28/0x68
slabs_destroy+0x60/0x90
___cache_free+0x1b4/0x358
kfree+0xc0/0x1d0
skb_free_head+0x2c/0x38
skb_release_data+0x110/0x1a0
skb_release_all+0x2c/0x38
consume_skb+0x38/0x130
__dev_kfree_skb_any+0x44/0x50
mlxsw_pci_rdq_fini+0x8c/0xb0
mlxsw_pci_queue_fini.isra.0+0x28/0x58
mlxsw_pci_queue_group_fini+0x58/0x88
mlxsw_pci_aqs_fini+0x2c/0x60
mlxsw_pci_fini+0x34/0x50
mlxsw_core_bus_device_unregister+0x104/0x1d0
mlxsw_devlink_core_bus_device_reload_down+0x2c/0x48
devlink_reload+0x44/0x158
devlink_nl_cmd_reload+0x270/0x290
genl_rcv_msg+0x188/0x2f0
netlink_rcv_skb+0x5c/0x118
genl_rcv+0x3c/0x50
netlink_unicast+0x1bc/0x278
netlink_sendmsg+0x194/0x390
__sys_sendto+0xe0/0x158
__arm64_sys_sendto+0x2c/0x38
el0_svc_common.constprop.0+0x70/0x168
do_el0_svc+0x28/0x88
el0_sync_handler+0x88/0x190
el0_sync+0x140/0x180
[2]
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1195432.html
[3]
https://patchwork.kernel.org/project/linux-scsi/patch/20170212214920.28866-1-anton@ozlabs.org/#20116693
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aa35e0bb5 ]
So far, "(null)" is reported for the node that is missing clocks.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/d6e24953-ea89-fd1c-6e16-7a0142118054@siemens.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92020e81dd ]
Disable vblanks immediately to save power. I think this was
missed when we merged DC support.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1781
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a689e8d1f8 ]
Clang static analysis reports this error
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2870:7: warning:
Dereference of null pointer [clang-analyzer-core.NullDereference]
if
(top_pipe_to_program->stream_res.tg->funcs->lock_doublebuffer_enable) {
^
top_pipe_to_program being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0100bce4f ]
Since commit 4b563a0666 ("ARM: imx: Remove imx21 support"), the config
DEBUG_IMX21_IMX27_UART is really only debug support for IMX27.
So, rename this option to DEBUG_IMX27_UART and adjust dependencies in
Kconfig and rename the definitions to IMX27 as further clean-up.
This issue was discovered with ./scripts/checkkconfigsymbols.py, which
reported that DEBUG_IMX21_IMX27_UART depends on the non-existing config
SOC_IMX21.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f756f435f7 ]
In case the following power domain sequence happens, iMX8M Mini always hangs:
gpumix:on -> gpu:on -> gpu:off -> gpu:on
This is likely due to another quirk of the GPC block. This situation can be
prevented by always synchronously powering off both the domain and MIX domain.
Make it so. This turns the aforementioned sequence into:
gpumix:on -> gpu:on -> gpu:off -> gpumix:off -> gpumix:on -> gpu:on
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f52dd33943 ]
Thermal zone names should not be longer than 20 names, which is indicated by
a message at boot. Change "camera-thermal-bottom" to "cam-thermal-bottom" to
fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211114012755.112226-6-konrad.dybcio@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd1d6da17c ]
Version 2.40a supports DDR_ECC_INTR_SUPPORT for a quirk, so use that
quirk to determine a call to setup_address_map().
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lkml.kernel.org/r/20211012190709.1504152-1-dinguyen@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Heiko Carstens
Iwona Winiarska
Russell King (Oracle)
Antoine Tenart
Sebastian Gottschall
Wen Gong
Wander Lairson Costa
Shaul Triebitz
Johannes Berg
Kieran Bingham
Mika Westerberg
Mauro Carvalho Chehab
Tsuchiya Yuto
Zhou Qingyang
Niklas Söderlund
James Hilliard
Laurent Pinchart
Joerg Roedel
Xiongwei Song
Neal Liu
Kishon Vijay Abraham I
Hans de Goede
Zack Rusin
Adam Ward
Mansur Alisha Shaik
Sriram R
Zekun Shen
Stephan Müller
Chengfeng Ye
Fugang Duan
Jiri Slaby
Martyn Welch
Martin Leung
Danielle Ratson
Jan Kiszka
Alex Deucher
Yang Li
Lukas Bulwahn
Marek Vasut
Konrad Dybcio
Dinh Nguyen