With arch/ppc gone and all in kernel users of CONFIG_PPC_CPM_NEW_BINDING
fixed up we dont have need for the Kconfig option anymore.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that arch/ppc is gone we always define CONFIG_PPC_CPM_NEW_BINDING so
we can remove all the code associated with !CONFIG_PPC_CPM_NEW_BINDING.
Also fixed some asm/of_platform.h to linux/of_platform.h (and of_device.h)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Mostly having to do with not marking things __iomem. And some failure
to use appropriate accessors to read MMIO regs.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The old code assumed there was only one, but the 8572 actually has 3.
Also, our usual id, 0xe0024520, gets resolved to -1 somewhere, and this was
preventing the multiple buses from having different ids. So we only keep
the low 20 bits, which have the interesting info, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.
i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Get rid of uses_fsl_uli_m1575, it does not scale for all cases.
Instead, let's explicitly use machine_is() for each fixup.
- Factor out MPC8610HPCD quirks to fsl_uli1575, and protect them with
machine_is(). One step closer to multiplatform kernels.
- Actually use fsl_uli1575 on MPC8610HPCD, so RTC quirk will be applied.
- RTC quirk applies to all boards though, so no machine_is() checks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes RTC on MPC8572DS boards: dummy read helps only when
reading at the end of the bridge's memory (i.e. outside of behind the
bridge devices' assigned regions).
With this change the quirk also makes RTC work on MPC8610HPCD, so it's
unlikely that this will break MPC8641HPCN or MPC8544DS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds few bindings for the new drivers to be submitted through
the appropriate maintainers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Freescale ships MPC8315E-RDB boards in two variants:
1. With TSEC1 ethernet support and USB UTMI PHY;
2. Without TSEC1 support, but with USB ULPI PHY in addition.
For the second case U-Boot will add status = "disabled"; property
into the TSEC1 node, so Linux should not try to probe it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We must not use MPC831X_SICR[HL]_* definitions for the MPC8315 processors,
because SICR USB bits locations are not compatible with MPC8313.
This patch fixes ULPI workability on MPC8315E-RDB boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This allows other platforms with the same pci block like MPC5121 to use it.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Choosing PCI or not at config time is allowed on some
platforms via an if expression in arch/powerpc/Kconfig.
To add a new platform with PCI support selectable at
config time, you must change the if expression. This
patch makes this easier by changing:
bool "PCI support" if <long expression>
to
bool "PCI support" if PPC_PCI_CHOICE
and adding select PPC_PCI_CHOICE to all the config nodes that
were previously in the PCI if expression.
Platforms with unconditional PCI support continue to
just select PCI in their config nodes.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc7448hpc2 board doesn't have an alias block like
most of the other modern eval boards have. We need this
block in order to have u-boot be able to make use of the
CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node)
in the future.
Also remove the old, redundant chosen node. Of all the modern
Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only
one which still has it. Its presence also breaks with some older
versions of u-boot, like 1.3.1 -- which try and insert a
second chosen node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic PM support for 83xx. Standby is implemented as sleep.
Suspend-to-RAM is implemented as "deep sleep" (with the processor
turned off) on 831x.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert to DTS version 1, eliminate some obsolete practices, and
correct some errors (compared to the actual 8540 device tree).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for_linus' of git://git.infradead.org/~dedekind/ubifs-2.6:
UBIFS: include to compilation
UBIFS: add new flash file system
UBIFS: add brief documentation
MAINTAINERS: add UBIFS section
do_mounts: allow UBI root device name
VFS: export sync_sb_inodes
VFS: move inode_lock into sync_sb_inodes
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (76 commits)
IDE: Report errors during drive reset back to user space
Update documentation of HDIO_DRIVE_RESET ioctl
IDE: Remove unused code
IDE: Fix HDIO_DRIVE_RESET handling
hd.c: remove the #include <linux/mc146818rtc.h>
update the BLK_DEV_HD help text
move ide/legacy/hd.c to drivers/block/
ide/legacy/hd.c: use late_initcall()
remove BLK_DEV_HD_ONLY
ide: endian annotations in ide-floppy.c
ide-floppy: zero out the whole struct ide_atapi_pc on init
ide-floppy: fold idefloppy_create_test_unit_ready_cmd into idefloppy_open
ide-cd: move request prep chunk from cdrom_do_newpc_cont to rq issue path
ide-cd: move request prep from cdrom_start_rw_cont to rq issue path
ide-cd: move request prep from cdrom_start_seek_continuation to rq issue path
ide-cd: fold cdrom_start_seek into ide_cd_do_request
ide-cd: simplify request issuing path
ide-cd: mv ide_do_rw_cdrom ide_cd_do_request
ide-cd: cdrom_start_seek: remove unused argument block
ide-cd: ide_do_rw_cdrom: add the catch-all bad request case to the if-else block
...
* 'release-2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-acpi-merge-2.6: (87 commits)
Fix FADT parsing
Add the ability to reset the machine using the RESET_REG in ACPI's FADT table.
ACPI: use dev_printk when possible
PNPACPI: add support for HP vendor-specific CCSR descriptors
PNP: avoid legacy IDE IRQs
PNP: convert resource options to single linked list
ISAPNP: handle independent options following dependent ones
PNP: remove extra 0x100 bit from option priority
PNP: support optional IRQ resources
PNP: rename pnp_register_*_resource() local variables
PNPACPI: ignore _PRS interrupt numbers larger than PNP_IRQ_NR
PNP: centralize resource option allocations
PNP: remove redundant pnp_can_configure() check
PNP: make resource assignment functions return 0 (success) or -EBUSY (failure)
PNP: in debug resource dump, make empty list obvious
PNP: improve resource assignment debug
PNP: increase I/O port & memory option address sizes
PNP: introduce pnp_irq_mask_t typedef
PNP: make resource option structures private to PNP subsystem
PNP: define PNP-specific IORESOURCE_IO_* flags alongside IRQ, DMA, MEM
...
Fail integrity check gracefully when request does not have a bio
attached (BLOCK_PC).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (82 commits)
NFSv4: Remove BKL from the nfsv4 state recovery
SUNRPC: Remove the BKL from the callback functions
NFS: Remove BKL from the readdir code
NFS: Remove BKL from the symlink code
NFS: Remove BKL from the sillydelete operations
NFS: Remove the BKL from the rename, rmdir and unlink operations
NFS: Remove BKL from NFS lookup code
NFS: Remove the BKL from nfs_link()
NFS: Remove the BKL from the inode creation operations
NFS: Remove BKL usage from open()
NFS: Remove BKL usage from the write path
NFS: Remove the BKL from the permission checking code
NFS: Remove attribute update related BKL references
NFS: Remove BKL requirement from attribute updates
NFS: Protect inode->i_nlink updates using inode->i_lock
nfs: set correct fl_len in nlmclnt_test()
SUNRPC: Support registering IPv6 interfaces with local rpcbind daemon
SUNRPC: Refactor rpcb_register to make rpcbindv4 support easier
SUNRPC: None of rpcb_create's callers wants a privileged source port
SUNRPC: Introduce a specific rpcb_create for contacting localhost
...
The (1.0 inherited) separate length fields in the FADT are byte granular.
Further, PM1a/b may have distinct lengths and live in distinct address spaces.
acpi_tb_convert_fadt() should account for all of these conditions.
Apart from these changes I'm puzzled by the fact that, not just for
acpi_gbl_xpm1{a,b}_enable, acpi_hw_low_level_{read,write}() get an explicit
size passed rather than using the size found in the passed GAS. What happens
on a platform that defines PM1{a,b} wider than 16 bits? Of course,
acpi_hw_low_level_{read,write}() at present are entirely un-prepared to deal
with sizes other than 8, 16, or 32, not to speak of a non-zero bit_offset or
access_width...
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Convert printks to use dev_printk(). The most obvious change will
be messages like this:
-ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 31 (level, low) -> IRQ 31
+cciss 0000:00:04.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The HP CCSR descriptor describes MMIO address space that should appear
as a MEM resource. This patch adds support for parsing these descriptors
in the _CRS data.
The visible effect of this is that these MEM resources will appear
in /sys/devices/pnp0/.../resources, which means that "lspnp -v" will
report it, user applications can use this to locate device CSR space,
and kernel drivers can use the normal PNP resource accessors to
locate them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
If an IDE controller is in compatibility mode, it expects to use
IRQs 14 and 15, so PNP should avoid them.
This patch should resolve this problem report:
parallel driver grabs IRQ14 preventing legacy SFF ATA controller from working
https://bugzilla.novell.com/show_bug.cgi?id=375836
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
ISAPNP, PNPBIOS, and ACPI describe the "possible resource settings" of
a device, i.e., the possibilities an OS bus driver has when it assigns
I/O port, MMIO, and other resources to the device.
PNP used to maintain this "possible resource setting" information in
one independent option structure and a list of dependent option
structures for each device. Each of these option structures had lists
of I/O, memory, IRQ, and DMA resources, for example:
dev
independent options
ind-io0 -> ind-io1 ...
ind-mem0 -> ind-mem1 ...
...
dependent option set 0
dep0-io0 -> dep0-io1 ...
dep0-mem0 -> dep0-mem1 ...
...
dependent option set 1
dep1-io0 -> dep1-io1 ...
dep1-mem0 -> dep1-mem1 ...
...
...
This data structure was designed for ISAPNP, where the OS configures
device resource settings by writing directly to configuration
registers. The OS can write the registers in arbitrary order much
like it writes PCI BARs.
However, for PNPBIOS and ACPI devices, the OS uses firmware interfaces
that perform device configuration, and it is important to pass the
desired settings to those interfaces in the correct order. The OS
learns the correct order by using firmware interfaces that return the
"current resource settings" and "possible resource settings," but the
option structures above doesn't store the ordering information.
This patch replaces the independent and dependent lists with a single
list of options. For example, a device might have possible resource
settings like this:
dev
options
ind-io0 -> dep0-io0 -> dep1->io0 -> ind-io1 ...
All the possible settings are in the same list, in the order they
come from the firmware "possible resource settings" list. Each entry
is tagged with an independent/dependent flag. Dependent entries also
have a "set number" and an optional priority value. All dependent
entries must be assigned from the same set. For example, the OS can
use all the entries from dependent set 0, or all the entries from
dependent set 1, but it cannot mix entries from set 0 with entries
from set 1.
Prior to this patch PNP didn't keep track of the order of this list,
and it assigned all independent options first, then all dependent
ones. Using the example above, that resulted in a "desired
configuration" list like this:
ind->io0 -> ind->io1 -> depN-io0 ...
instead of the list the firmware expects, which looks like this:
ind->io0 -> depN-io0 -> ind-io1 ...
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ISAPNP spec recommends that independent options precede
dependent ones, but this is not actually required. The current
ISAPNP code incorrectly puts such trailing independent options
at the end of the last dependent option list.
This patch fixes that bug by resetting the current option list
to the independent list when we see an "End Dependent Functions"
tag. PNPBIOS and PNPACPI handle this the same way.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When building resource options, ISAPNP and PNPBIOS set the priority
to something like "0x100 | PNP_RES_PRIORITY_ACCEPTABLE", but we
immediately mask off the 0x100 again in pnp_build_option(), so that
bit looks superfluous.
Thanks to Rene Herman <rene.herman@gmail.com> for pointing this out.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds an IORESOURCE_IRQ_OPTIONAL flag for use when
assigning resources to a device. If the flag is set and we are
unable to assign an IRQ to the device, we can leave the IRQ
disabled but allow the overall resource allocation to succeed.
Some devices request an IRQ, but can run without an IRQ
(possibly with degraded performance). This flag lets us run
the device without the IRQ instead of just leaving the
device disabled.
This is a reimplementation of this previous change by Rene
Herman <rene.herman@gmail.com>:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=3b73a223661ed137c5d3d2635f954382e94f5a43
I reimplemented this for two reasons:
- to prepare for converting all resource options into a single linked
list, as opposed to the per-resource-type lists we have now, and
- to preserve the order and number of resource options.
In PNPBIOS and ACPI, we configure a device by giving firmware a
list of resource assignments. It is important that this list
has exactly the same number of resources, in the same order,
as the "template" list we got from the firmware in the first
place.
The problem of a sound card MPU401 being left disabled for want of
an IRQ was reported by Uwe Bugla <uwe.bugla@gmx.de>.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No functional change; just rename "data" to something more
descriptive.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI Extended Interrupt Descriptors can encode 32-bit interrupt
numbers, so an interrupt number may exceed the size of the bitmap
we use to track possible IRQ settings.
To avoid corrupting memory, complain and ignore too-large interrupt
numbers.
There's similar code in pnpacpi_parse_irq_option(), but I didn't
change that because the small IRQ descriptor can only encode
IRQs 0-15, which do not exceed bitmap size.
In the future, we could handle IRQ numbers greater than PNP_IRQ_NR
by replacing the bitmap with a table or list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch moves all the option allocations (pnp_mem, pnp_port, etc)
into the pnp_register_{mem,port,irq,dma}_resource() functions. This
will make it easier to rework the option data structures.
The non-trivial part of this patch is the IRQ handling. The backends
have to allocate a local pnp_irq_mask_t bitmap, populate it, and pass
a pointer to pnp_register_irq_resource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pnp_assign_resources() is static and the only caller checks
pnp_can_configure() before calling it, so no need to do it
again.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch doesn't change any behavior; it just makes the return
values more conventional.
This changes pnp_assign_dma() from a void function to one that
returns an int, just like the other assignment functions. For
now, at least, pnp_assign_dma() always returns 0 (success), so
it appears to never fail, just like before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the resource list is empty, say that explicitly. Previously,
it was confusing because often the heading was followed by zero
resource lines, then some "add resource" lines from auto-assignment,
so the "add" lines looked like current resources.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When we fail to assign an I/O or MEM resource, include the min/max
in the debug output to help match it with the options.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI Address Space Descriptors can be up to 64 bits wide.
We should keep track of the whole thing when parsing resource
options, so this patch changes PNP port and mem option
fields from "unsigned short" and "unsigned int" to
"resource_size_t".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This adds a typedef for the IRQ bitmap, which should cause
no functional change, but will make it easier to pass a
pointer to a bitmap to pnp_register_irq_resource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Nothing outside the PNP subsystem should need access to a
device's resource options, so this patch moves the option
structure declarations to a private header file.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
PNP previously defined PNP_PORT_FLAG_16BITADDR and PNP_PORT_FLAG_FIXED
in a private header file, but put those flags in struct resource.flags
fields. Better to make them IORESOURCE_IO_* flags like the existing
IRQ, DMA, and MEM flags.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No functional change; just make a couple declarations
consistent with the rest of the file.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As part of a heuristic to identify modem devices, 8250_pnp.c
checks to see whether a device can be configured at any of the
legacy COM port addresses.
This patch moves the code that traverses the PNP "possible resource
options" from 8250_pnp.c to the PNP subsystem. This encapsulation
is important because a future patch will change the implementation
of those resource options.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rather than stepping through all IO resources, then stepping through
all MMIO resources, etc., we can just iterate over the resource list
once directly.
This can change the order in /sys, e.g.,
# cat /sys/devices/pnp0/00:07/resources # OLD
state = active
io 0x3f8-0x3ff
irq 4
# cat /sys/devices/pnp0/00:07/resources # NEW
state = active
irq 4
io 0x3f8-0x3ff
The old code artificially sorted resources by type; the new code
just lists them in the order we read them from the ISAPNP hardware
or the BIOS.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
We used to have a fixed-size resource table. If a device had
twenty resources when the table only had space for ten, we didn't
need ten warnings, so we added the ratelimit.
Now that we can dynamically allocate new resources, we should
only get failures if the allocation fails. That should be
rare enough that we don't need to ratelimit the messages.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Kumar Gala
Scott Wood
Andy Fleming
Anton Vorontsov
Jochen Friedrich
John Rigby
Paul Gortmaker
Linus Torvalds
Martin K. Petersen
Jan Beulich
Aaron Durbin
Bjorn Helgaas