Граф коммитов

1532 Коммитов

Автор SHA1 Сообщение Дата
Jeroen Hofstee 23c5a9488f can: c_can: D_CAN: c_can_chip_config(): perform a sofware reset on open
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.

According to [1], the C_CAN module doesn't have the software reset.

[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf

Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:21 +01:00
Kurt Van Dijck 3cb3eaac52 can: c_can: c_can_poll(): only read status register after status IRQ
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.

It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.

Thanks to Wolfgang and Joe for bringing up the first idea.

Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:21 +01:00
Jeroen Hofstee 128a1b87d3 can: peak_usb: report bus recovery as well
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.

Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.

Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:20 +01:00
Johan Hovold f7a1337f0d can: peak_usb: fix slab info leak
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.

The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).

Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org>     # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:20 +01:00
Stephane Grosjean de280f403f can: peak_usb: fix a potential out-of-sync while decoding packets
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.

This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes: 46be265d33 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:20 +01:00
Joakim Zhang 5e269324db can: flexcan: disable completely the ECC mechanism
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.

Fixes: cdce844865 ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:20 +01:00
Johan Hovold 3759739426 can: usb_8dev: fix use-after-free on disconnect
The driver was accessing its driver data after having freed it.

Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Cc: stable <stable@vger.kernel.org>     # 3.9
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:20 +01:00
Johan Hovold 4d6636498c can: mcba_usb: fix use-after-free on disconnect
The driver was accessing its driver data after having freed it.

Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: stable <stable@vger.kernel.org>     # 4.12
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Reported-by: syzbot+e29b17e5042bbc56fae9@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:20 +01:00
Navid Emamdoost fb5be6a7b4 can: gs_usb: gs_can_open(): prevent memory leak
In gs_can_open() if usb_submit_urb() fails the allocated urb should be
released.

Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:20 +01:00
Wen Yang db9ee384f6 can: dev: add missing of_node_put() after calling of_get_child_by_name()
of_node_put() needs to be called when the device node which is got
from of_get_child_by_name() finished using.

Fixes: 2290aefa2e ("can: dev: Add support for limiting configured bitrate")
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-11-04 21:47:20 +01:00
Krzysztof Kozlowski 02bc5eb990 drivers: net: Fix Kconfig indentation
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
    $ sed -e 's/^        /\t/' -i */Kconfig

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-26 08:56:17 +02:00
David S. Miller 44c40910b6 linux-can-next-for-5.4-20190904
-----BEGIN PGP SIGNATURE-----
 
 iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl1vrJITHG1rbEBwZW5n
 dXRyb25peC5kZQAKCRBaxiGjkeSdIC8BB/98XcWiaInD+SM6UjD2dVd1r0zhPKJS
 WBK58G81+op3YP4DY8Iy+C24uZBlSlutVGoD/PIrZF39xXsnOtJuMVHC4LvtdADC
 30uI/61JQNEjuX2AiTFudqDvYjZZKZ28HLqEnO2pWk3dMVL3+fkS3i7VQR7KJ/Gr
 BYM6EzCdkbuWW/zsAVbKLJ8NswVmcdjP7eSK+exKppoWMtgCglZw1X6iP5YXDnbK
 h3dGs687u8RfUra7j7vgnJzyQU4draMPsabaLDT5qw1PgYQ3k8MTVMBlULR0+HHO
 qkBqumRwfOxay0z0XOgRuWrICKTH/b0SRLp3H53ZyfDo6+4TC9KGHRgX
 =gwfZ
 -----END PGP SIGNATURE-----

Merge tag 'linux-can-next-for-5.4-20190904' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2019-09-04 j1939

this is a pull request for net-next/master consisting of 21 patches.

the first 12 patches are by me and target the CAN core infrastructure.
They clean up the names of variables , structs and struct members,
convert can_rx_register() to use max() instead of open coding it and
remove unneeded code from the can_pernet_exit() callback.

The next three patches are also by me and they introduce and make use of
the CAN midlayer private structure. It is used to hold protocol specific
per device data structures.

The next patch is by Oleksij Rempel, switches the
&net->can.rcvlists_lock from a spin_lock() to a spin_lock_bh(), so that
it can be used from NAPI (soft IRQ) context.

The next 4 patches are by Kurt Van Dijck, he first updates his email
address via mailmap and then extends sockaddr_can to include j1939
members.

The final patch is the collective effort of many entities (The j1939
authors: Oliver Hartkopp, Bastian Stender, Elenita Hinds, kbuild test
robot, Kurt Van Dijck, Maxime Jayat, Robin van der Gracht, Oleksij
Rempel, Marc Kleine-Budde). It adds support of SAE J1939 protocol to the
CAN networking stack.

SAE J1939 is the vehicle bus recommended practice used for communication
and diagnostics among vehicle components. Originating in the car and
heavy-duty truck industry in the United States, it is now widely used in
other parts of the world.

P.S.: This pull request doesn't invalidate my last pull request:
      "pull-request: can-next 2019-09-03".
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-05 12:17:50 +02:00
Marc Kleine-Budde 8df9ffb888 can: make use of preallocated can_ml_priv for per device struct can_dev_rcv_lists
This patch removes the old method of allocating the per device protocol
specific memory via a netdevice_notifier. This had the drawback, that
the allocation can fail, leading to a lot of null pointer checks in the
code. This also makes the live cycle management of this memory quite
complicated.

This patch switches from the allocating the struct can_dev_rcv_lists in
a NETDEV_REGISTER call to using the dev->ml_priv, which is allocated by
the driver since the previous patch.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-04 13:29:15 +02:00
Marc Kleine-Budde ffd956eef6 can: introduce CAN midlayer private and allocate it automatically
This patch introduces the CAN midlayer private structure ("struct
can_ml_priv") which should be used to hold protocol specific per device
data structures. For now it's only member is "struct can_dev_rcv_lists".

The CAN midlayer private is allocated via alloc_netdev()'s private and
assigned to "struct net_device::ml_priv" during device creation. This is
done transparently for CAN drivers using alloc_candev(). The slcan, vcan
and vxcan drivers which are not using alloc_candev() have been adopted
manually. The memory layout of the netdev_priv allocated via
alloc_candev() will looke like this:

  +-------------------------+
  | driver's priv           |
  +-------------------------+
  | struct can_ml_priv      |
  +-------------------------+
  | array of struct sk_buff |
  +-------------------------+

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-04 13:29:14 +02:00
Marc Kleine-Budde 13ecee77fa can: dev: can_dev_init(): convert from printk(KERN_INFO) to pr_info
This patch converts the printk(KERN_INFO) in can_dev_init() to
pr_info().

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:28:13 +02:00
Marc Kleine-Budde d36673f591 can: dev: can_dellink(): remove return at end of void function
This patch remove the return at the end of the void function
can_dellink().

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:28:13 +02:00
Marc Kleine-Budde f59d7824bf can: dev: can_restart(): convert NULL pointer check
This patch converts the NULL pointer check in can_restart() form "skb ==
NULL" to "!skb".

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:28:13 +02:00
Marc Kleine-Budde d726c01aa7 can: dev: remove unnecessary blank line
This patch removes unnecessary blank lines, so that checkpatch doesn't
complain anymore.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:28:13 +02:00
Marc Kleine-Budde 39fe6fd5fb can: dev: remove unnecessary parentheses
This patch removes unnecessary parentheses from the generic CAN device
infrastructure.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:28:13 +02:00
Marc Kleine-Budde d7bda73070 can: dev: avoid long lines
This patch fixes long lines in the generic CAN device infrastructure.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:28:13 +02:00
Marc Kleine-Budde ee9a5f5e55 can: dev: convert block comments to network style comments
This patch converts all block comments to network subsystem style block
comments.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:23:57 +02:00
Andy Shevchenko 761a615917 can: mcp251x: Call wrapper instead of regulator_disable()
There is no need to check for regulator presence in the ->suspend()
since a wrapper does it for us. Due to this we may unconditionally set
AFTER_SUSPEND_POWER flag.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:23:57 +02:00
Andy Shevchenko 8de29a5c34 can: mcp251x: Make use of device property API
Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:23:57 +02:00
Andy Shevchenko b4cb76961c can: mcp251x: Use devm_clk_get_optional() to get the input clock
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). This comes with a small functional change: previously
all errors were ignored when platform data is present. Now all errors are
treated as errors. If no input clock is present devm_clk_get_optional() will
return NULL instead of an error which matches the behavior of the old code.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:23:57 +02:00
Marc Kleine-Budde f6cae800bf can: mcp251x: remove deprecated board file setup example
In the pre device-tree ARM aera there were board files that configured
the system (instead of a device tree). A "struct spi_board_info" was
used to describe the SPI bus.

As new systems should be described via device trees, this patch removes
the board setup example from the driver. The "struct
mcp251x_platform_data" cannot be removed completely, as there are still
some in-tree users of this file.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:23:57 +02:00
Dan Murphy 81f29dd304 can: tcan4x5x: Remove checking the wake pin
Remove checking the wake pin for every read/write call.
The device is not explicitly put to sleep in the code
and the POR interrupt is cleared during the init of
the device.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:23:57 +02:00
Dan Murphy be1d28424a can: tcan4x5x: Remove data-ready gpio interrupt
Remove the data-ready gpio interrupt handling and use the spi->irq
that is created based on the interrupt DT property.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:23:57 +02:00
Christer Beskow ec44dd5790 can: kvaser_pciefd: the PWM generator is running at the bus frequency of the system.
The system clock frequency for the bus connected to the PCIe controller
shall be used when calculating the frequency of the PWM, not the CAN
system clock frequency.

Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-09-03 10:23:57 +02:00
Markus Elfring 038dab7efc can: Delete unnecessary checks before the macro call “dev_kfree_skb”
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22 16:22:03 -07:00
Marc Kleine-Budde df58525df3 can: mcp251x: remove custom DMA mapped buffer
There is no need to duplicate what SPI core already does, i.e. mapping buffers
for DMA capable transfers. This patch removes all related pices of code.

Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Phil Elwell 6a07c2305a can: mcp251x: Use DT-supplied interrupt flags
The MCP2515 datasheet clearly describes a level-triggered interrupt pin.
Therefore the receiving interrupt controller must also be configured for
level-triggered operation otherwise there is a danger of a missed
interrupt condition blocking all subsequent interrupts. The ONESHOT
flag ensures that the interrupt is masked until the threaded interrupt
handler exits.

Rather than change the flags globally (they must have worked for at
least one user), keep the old behavior for for non DT devices. DT based
devices specify the flags in their corresonding DT node.

See: https://github.com/raspberrypi/linux/issues/2175
     https://github.com/raspberrypi/linux/issues/2263

Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Alexander Shiyan 3964576307 can: mcp251x: Use dev_name() during request_threaded_irq()
Passing driver name as name during request_threaded_irq() results in all
CAN IRQs have same name. This does not help much to easily identify which
IRQ belongs to which CAN instance. Therefore pass dev_name() during
request_threaded_irq() so that better identifiable name is listed for
CAN devices in cat /proc/interrupts output.

Output of cat /proc/interrupts
Before this patch:
  253:          2  gpio-mxc  13 Edge      mcp251x
  259:          2  gpio-mxc  19 Edge      mcp251x
After this patch:
  253:          2  gpio-mxc  13 Edge      spi1.1
  259:          2  gpio-mxc  19 Edge      spi1.2

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde d84ea2123f can: mcp251x: mcp251x_hw_reset(): allow more time after a reset
Some boards take longer than 5ms to power up after a reset, so allow
some retries attempts before giving up.

Fixes: ff06d611a3 ("can: mcp251x: Improve mcp251x_hw_reset()")
Cc: linux-stable <stable@vger.kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde af669cd26e can: mcp251x: use u8 instead of uint8_t
This patch changes all the uint8_t in the arguments in several function
to u8.

Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde d344c6d6c3 can: mcp251x: fix print formating strings
This patch fixes the print format strings in the driver.

Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde 4669597496 can: mcp251x: avoid long lines
This patch fixes long lines in the driver.

Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde 77654a6da0 can: mcp251x: remove unnecessary blank lines
This patch removes unnecessary blank lines, so that checkpatch doesn't
complain anymore.

Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde 3b9bcede4d can: mcp251x: convert block comments to network style comments
This patch converts all block comments to network subsystem style block
comments.

Acked-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde b3402c4057 can: m_can_platform: m_can_plat_probe(): add missing error handling if mcan_class is NULL
This patch adds the missing error handling in m_can_plat_probe() if
mcan_class is NULL.

Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde 28b0ffe98b can: m_can_platform: remove not needed casts to struct m_can_plat_priv *
The struct m_can_classdev::device_data is a void pointer, so there's no
need to cast it to struct m_can_plat_priv *, when assigning the struct
m_can_plat_priv pointer.

This patch removes the not needed casts from the m_can_platform driver.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde 6093f744fe can: tcan4x5x: fix data length in regmap write path
In regmap_spi_gather_write() the "addr" is prepared. The chip expects
the number of 32 bit words to write in the lower 8 bits of addr. However
the number of byte to write in shifted left by 3 (== divided by 8).

The function tcan4x5x_regmap_write() is called with a data buffer, which
holds the register information in the first 32 bits, followed by the
actual data. tcan4x5x_regmap_write() calls regmap_spi_gather_write()
with the val pointer pointing to the actual data (i.e. the original
pointer is incremented by 4 bytes), but without decrementing the count.

If the regmap framework only calls tcan4x5x_regmap_write() to read
single 32 bit registers these two bugs cancel each other.

This patch fixes the code.

Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde 7fbda13065 can: tcan4x5x: tcan4x5x_can_probe(): add missing error handling if mcan_class is NULL
This patch adds the missing error handling in tcan4x5x_can_probe() if
mcan_class is NULL.

Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:26 +02:00
Marc Kleine-Budde ad07819f22 can: tcan4x5x: remove not needed casts to struct tcan4x5x_priv *
The struct m_can_classdev::device_data is a void pointer, so there's no
need to cast it to struct tcan4x5x_priv *, when assigning the struct
tcan4x5x_priv pointer.

This patch removes the not needed casts from the tcan4x5x driver.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:25 +02:00
Marc Kleine-Budde 65668b3269 can: tcan4x5x: remove unused struct tcan4x5x_priv::tcan4x5x_lock
The mutex struct tcan4x5x_priv::tcan4x5x_lock is unused in the driver,
so this patch removes the variable from the driver.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:25 +02:00
Marc Kleine-Budde 653ee35ce6 can: hi311x: remove custom DMA mapped buffer
There is no need to duplicate what SPI core already does, i.e. mapping buffers
for DMA capable transfers. This patch removes all related pices of code.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:25 +02:00
Nishka Dasgupta 1f0dee39e3 can: peak_pci: Make structure peak_pciec_i2c_bit_ops constant
Static structure peak_pciec_i2c_bit_ops, of type i2c_algo_bit_data, is
not used except to be copied into another variable. Hence make it const
to protect it from modification.

Issue found with Coccinelle.

Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:25 +02:00
Geert Uytterhoeven 30cc0ed73e can: rcar_can: Remove unused platform data support
All R-Car platforms use DT for describing CAN controllers. R-Car CAN
platform data support was never used in any upstream kernel.

Move the Clock Select Register settings enum into the driver, and remove
platform data support and the corresponding header file.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-20 13:41:25 +02:00
Marc Kleine-Budde e83e416cdf can: vcan: introduce pr_fmt and make use of it
This patch introduces pr_fmt and makes use of it, also it converts a
printk() to pr_info().

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 17:32:21 +02:00
Marc Kleine-Budde 4248f5e02f can: vcan: remove unnecessary blank lines
This patch removes unnecessary blank lines, so that checkpatch doesn't
complain anymore.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 17:32:21 +02:00
Marc Kleine-Budde d569de8149 can: vcan: convert block comments to network style comments
This patch converts all block comments to network subsystem style block
comments.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 17:32:21 +02:00
Srinivas Neeli 3e994ff28f can: xilinx_can: xcan_set_bittiming(): fix the data phase btr1 calculation
While calculating bitrate for the data phase, the driver is using phase
segment 1 of the arbitration phase instead of the data phase.

Fixes: c223da6 ("can: xilinx_can: Add support for CANFD FD frames")
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Acked-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 17:32:19 +02:00
Appana Durga Kedareswara rao 9d06bcb9aa can: xilinx_can: xcan_rx_fifo_get_next_frame(): fix FSR register FL and RI mask values for canfd 2.0
For CANFD 2.0 IP configuration existing driver is using incorrect mask
values for FSR register FL and RI fields.

Fixes: c223da6 ("can: xilinx_can: Add support for CANFD FD frames")
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Acked-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 17:32:19 +02:00
Appana Durga Kedareswara rao e6997dd268 can: xilinx_can: fix the data update logic for CANFD FD frames
commit c223da6893 ("can: xilinx_can: Add support for CANFD FD frames")
is writing data to a wrong offset for FD frames.

This patch fixes this issue.

Fixes: c223da6 ("can: xilinx_can: Add support for CANFD FD frames")
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 17:31:26 +02:00
Appana Durga Kedareswara rao 93bbd6c5ee can: xilinx_can: xcanfd_rx(): fix FSR register handling in the RX path
After commit c223da6893 ("can: xilinx_can: Add support for CANFD FD
frames") the driver is updating the FSR IRI index multiple times (i.e in
xcanfd_rx() and xcan_rx_fifo_get_next_frame()), It should be updated
once per RX packet. This patch fixes this issue, also this patch removes
the unnecessary fsr register checks in xcanfd_rx() API.

Fixes: c223da6 ("can: xilinx_can: Add support for CANFD FD frames")
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:44:53 +02:00
Venkatesh Yadav Abbarapu 6b0d35891c can: xilinx_can: xcan_probe(): skip error message on deferred probe
When can clock is provided from the clock wizard, clock wizard driver
may not be available when can driver probes resulting to the error
message "Device clock not found error".

As this error message is not very userful to the end user, skip printing
it in the case of deferred probe.

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:43:22 +02:00
Anssi Hannula 3486cc40cc can: xilinx_can: xcan_chip_start(): fix failure with invalid bus
Currently the xilinx_can xcan_chip_start() function, called from
.ndo_open() and via CAN_MODE_START (bus-off restart), waits for the SR
register to show the wanted operating state, with a 1 sec timeout.

However, that register bit will only be set once the HW has observed 11
consecutive recessive bits (BusIdle) on the bus.

If the bus will not see the 11 bits (e.g. it is stuck dominant), the
function will timeout and return an error. If this was done as part of a
scheduled restart from bus-off, the interface will stay in bus-off state
forever even if the bus recovers later.

According to M_CAN and FLEXCAN documentation they also wait for 11
consecutive recessive bits, but their drivers do not seem to wait for
that.

To make the behavior consistent, modify xilinx_can to also not wait for
the synchronization to complete.

The only way for users to know for sure that the bus has been joined
successfully is to see successfully received or transmitted frames. That
does not seem optimal, but it is consistent with other drivers and we
should have a properly working restart-ms with xilinx_can.

Tested on ZynqMP with Xilinx CAN-FD 1.0.

Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:42:05 +02:00
YueHaibing 7123e1c7ea can: ti_hecc: ti_hecc_mailbox_read(): remove set but not used variable 'mbx_mask'
Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/can/ti_hecc.c: In function 'ti_hecc_mailbox_read':
drivers/net/can/ti_hecc.c:533:12: warning:
 variable 'mbx_mask' set but not used [-Wunused-but-set-variable]

It is never used so can be removed.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:40:29 +02:00
Marc Kleine-Budde babfcda6ef can: ti_hecc: ti_hecc_mailbox_read(): add blank lines to improve readability
This patch adds two blank lines in ti_hecc_mailbox_read() to improve the
readability of the function.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:37:04 +02:00
Marc Kleine-Budde c71400cec4 can: ti_hecc: ti_hecc_start(): avoid multiple assignments
This patch changes the multiple assignments of HECC_TX_MASK in
ti_hecc_start() into two single ones.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:37:04 +02:00
Marc Kleine-Budde dfa9352dbe can: ti_hecc: fix print formating strings
This patch fixes the print format strings in the driver.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:37:04 +02:00
Marc Kleine-Budde ab3a78f659 can: ti_hecc: avoid long lines
This patch fixes long lines in the driver.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:37:04 +02:00
Marc Kleine-Budde d5f1a984ed can: ti_hecc: fix indention
This patch fixes the indention in the driver.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:37:03 +02:00
Marc Kleine-Budde 99a3d7c122 can: ti_hecc: convert block comments to network style comments
This patch converts all block comments to network subsystem style block
comments.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:37:03 +02:00
YueHaibing 175a60b73b can: sja1000: f81601: remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:37:03 +02:00
YueHaibing 5549369cfd can: kvaser_pciefd: Remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:37:03 +02:00
Christer Beskow 1910cd8853 can: kvaser_pciefd: kvaser_pciefd_pwm_stop(): remove unnecessary code when setting pwm duty cycle to zero
To set the duty cycle to zero (i.e. pwm_stop), the trigger value shall
be equal to the top value.

This is achieved by reading the value of the top bit field from the pwm
register and then writing back this value to the trigger and top bit
fields.

Addresses-Coverity: ("Logically dead code")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:36:52 +02:00
David S. Miller 13dfb3fa49 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Just minor overlapping changes in the conflicts here.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-06 18:44:57 -07:00
Linus Torvalds 33920f1ec5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
 "Yeah I should have sent a pull request last week, so there is a lot
  more here than usual:

   1) Fix memory leak in ebtables compat code, from Wenwen Wang.

   2) Several kTLS bug fixes from Jakub Kicinski (circular close on
      disconnect etc.)

   3) Force slave speed check on link state recovery in bonding 802.3ad
      mode, from Thomas Falcon.

   4) Clear RX descriptor bits before assigning buffers to them in
      stmmac, from Jose Abreu.

   5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
      loops, from Nishka Dasgupta.

   6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.

   7) Need to hold sock across skb->destructor invocation, from Cong
      Wang.

   8) IP header length needs to be validated in ipip tunnel xmit, from
      Haishuang Yan.

   9) Use after free in ip6 tunnel driver, also from Haishuang Yan.

  10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
      Heiner Kallweit.

  11) Upon bridge device init failure, we need to delete the local fdb.
      From Nikolay Aleksandrov.

  12) Handle erros from of_get_mac_address() properly in stmmac, from
      Martin Blumenstingl.

  13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
      Kadlecsik.

  14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
      some devices, so revert. From Johannes Berg.

  15) Fix deadlock in rxrpc, from David Howells.

  16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
      Haibing.

  17) Fix mvpp2 crash on module removal, from Matteo Croce.

  18) Fix race in genphy_update_link, from Heiner Kallweit.

  19) bpf_xdp_adjust_head() stopped working with generic XDP when we
      fixes generic XDP to support stacked devices properly, fix from
      Jesper Dangaard Brouer.

  20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
      David Ahern.

  21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
  net: dsa: sja1105: Fix memory leak on meta state machine error path
  net: dsa: sja1105: Fix memory leak on meta state machine normal path
  net: dsa: sja1105: Really fix panic on unregistering PTP clock
  net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
  net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
  net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
  net: sched: sample: allow accessing psample_group with rtnl
  net: sched: police: allow accessing police->params with rtnl
  net: hisilicon: Fix dma_map_single failed on arm64
  net: hisilicon: fix hip04-xmit never return TX_BUSY
  net: hisilicon: make hip04_tx_reclaim non-reentrant
  tc-testing: updated vlan action tests with batch create/delete
  net sched: update vlan action for batched events operations
  net: stmmac: tc: Do not return a fragment entry
  net: stmmac: Fix issues when number of Queues >= 4
  net: stmmac: xgmac: Fix XGMAC selftests
  be2net: disable bh with spin_lock in be_process_mcc
  net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
  net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
  net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
  ...
2019-08-06 17:11:59 -07:00
Tomas Bortoli ead16e53c2 can: peak_usb: pcan_usb_pro: Fix info-leaks to USB devices
Uninitialized Kernel memory can leak to USB devices.

Fix by using kzalloc() instead of kmalloc() on the affected buffers.

Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+d6a5a1a3657b596ef132@syzkaller.appspotmail.com
Fixes: f14e22435a ("net: can: peak_usb: Do not do dma on the stack")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-02 13:58:01 +02:00
Tomas Bortoli 30a8beeb30 can: peak_usb: pcan_usb_fd: Fix info-leaks to USB devices
Uninitialized Kernel memory can leak to USB devices.

Fix by using kzalloc() instead of kmalloc() on the affected buffers.

Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+513e4d0985298538bf9b@syzkaller.appspotmail.com
Fixes: 0a25e1f4f1 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-02 13:57:48 +02:00
Wang Xiayang e787f19373 can: peak_usb: force the string buffer NULL-terminated
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string is
passed to dev_info() which relies on the NULL-termination.

Use strlcpy() instead.

This issue is identified by a Coccinelle script.

Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-02 13:27:30 +02:00
Wang Xiayang cd28aa2e05 can: sja1000: force the string buffer NULL-terminated
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string
'name' is passed to dev_info which relies on NULL-termination.

Use strlcpy() instead.

This issue is identified by a Coccinelle script.

Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-02 13:26:10 +02:00
Stephen Boyd d1a55841ab net: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-30 14:37:35 -07:00
Gustavo A. R. Silva 5a8dadbcfa can: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warnings:

drivers/net/can/peak_canfd/peak_pciefd_main.c:668:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/spi/mcp251x.c:875:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:895:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:953:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c: In function ‘pcan_usb_decode_error’:
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (n & PCAN_USB_ERROR_BUS_LIGHT) {
      ^
drivers/net/can/usb/peak_usb/pcan_usb.c:428:2: note: here
  case CAN_STATE_ERROR_WARNING:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.

Notice that in some cases spelling mistakes were fixed.
In other cases, the /* fall through */ comment is placed
at the bottom of the case statement, which is what GCC
is expecting to find.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
2019-07-25 20:09:42 -05:00
Stephane Grosjean fee6a8923a can: peak_usb: fix potential double kfree_skb()
When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.

Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:16:31 +02:00
Joakim Zhang 5f186c257f can: flexcan: fix stop mode acknowledgment
To enter stop mode, the CPU should manually assert a global Stop Mode
request and check the acknowledgment asserted by FlexCAN. The CPU must
only consider the FlexCAN in stop mode when both request and
acknowledgment conditions are satisfied.

Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:16:31 +02:00
Wen Yang e9f2a856e1 can: flexcan: fix an use-after-free in flexcan_setup_stop_mode()
The gpr_np variable is still being used in dev_dbg() after the
of_node_put() call, which may result in use-after-free.

Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:16:31 +02:00
Weitao Hou 375f755899 can: mcp251x: add error check when wq alloc failed
add error check when workqueue alloc failed, and remove redundant code
to make it clear.

Fixes: e0000163e3 ("can: Driver for the Microchip MCP251x SPI CAN controllers")
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:10:15 +02:00
Nikita Yushchenko d4b890aec4 can: rcar_canfd: fix possible IRQ storm on high load
We have observed rcar_canfd driver entering IRQ storm under high load,
with following scenario:
- rcar_canfd_global_interrupt() in entered due to Rx available,
- napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state
- Rx fifo interrupts are masked,
- rcar_canfd_global_interrupt() is entered again, this time due to
  error interrupt (e.g. due to overflow),
- since scheduled napi poller has not yet executed, condition for calling
  napi_schedule_prep() from rcar_canfd_global_interrupt() remains true,
  thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag
  in state,
- later, napi poller function rcar_canfd_rx_poll() gets executed, and
  calls napi_complete_done(),
- due to NAPIF_STATE_MISSED flag in state, this call does not clear
  NAPIF_STATE_SCHED flag from state,
- on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx
  interrutps,
- Rx interrupt happens, rcar_canfd_global_interrupt() gets called
  and calls napi_schedule_prep(),
- since NAPIF_STATE_SCHED is set in state at this time, this call
  returns false,
- due to that false return, rcar_canfd_global_interrupt() returns
  without masking Rx interrupt
- and this results into IRQ storm: unmasked Rx interrupt happens again
  and again is misprocessed in the same way.

This patch fixes that scenario by unmasking Rx interrupts only when
napi_complete_done() returns true, which means it has cleared
NAPIF_STATE_SCHED in state.

Fixes: dd3bd23eb4 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:07:57 +02:00
Rasmus Villemoes c63845609c can: dev: call netif_carrier_off() in register_candev()
CONFIG_CAN_LEDS is deprecated. When trying to use the generic netdev
trigger as suggested, there's a small inconsistency with the link
property: The LED is on initially, stays on when the device is brought
up, and then turns off (as expected) when the device is brought down.

Make sure the LED always reflects the state of the CAN device.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:06:39 +02:00
Jeroen Hofstee 4c7f715485 can: ti_hecc: use timestamp based rx-offloading
As already mentioned in [1] and included in [2], there is an off by one
issue since the high bank is already enabled when the _next_ mailbox to
be read has index 12, so the mailbox being read was 13. The message can
therefore go into mailbox 31 and the driver will be repolled until the
mailbox 12 eventually receives a msg. Or the message might end up in the
12th mailbox, but then it would become disabled after reading it and only
be enabled again in the next "round" after mailbox 13 was read, which can
cause out of order messages, since the lower priority mailboxes can
accept messages in the meantime.

As mentioned in [3] there is a hardware race condition when changing the
CANME register while messages are being received. Even when including a
busy poll on reception, like in [2] there are still overflows and out of
order messages at times, but less then without the busy loop polling.
Unlike what the patch suggests, the polling time is not in the microsecond
range, but takes as long as a current CAN bus reception needs to finish,
so typically more in the fraction of millisecond range. Since the timeout
is in jiffies it won't timeout.

Even with these additional fixes the driver is still not able to provide a
proper FIFO which doesn't drop packages. So change the driver to use
rx-offload and base order on timestamp instead of message box numbers. As
a side affect, this also fixes [4] and [5].

Before this change messages with a single byte counter were dropped /
received out of order at a bitrate of 250kbit/s on an am3517. With this
patch that no longer occurs up to and including 1Mbit/s.

[1] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post6
[2] http://arago-project.org/git/projects/?p=linux-omap3.git;a=commit;h=02346892777f07245de4d5af692513ebd852dcb2
[3] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post5
[4] https://patchwork.ozlabs.org/patch/895956/
[5] https://www.spinics.net/lists/netdev/msg494971.html

Cc: Anant Gole <anantgole@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Sean Nyekjaer 915f966642 can: flexcan: add support for DT property 'wakeup-source'
The flexcan controller can be forced as a wakeup source by
stating that explicitly in the device's .dts file using the
"wakeup-source" boolean property.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Dong Aisheng 8c306bec2d can: flexcan: add support for PE clock source select
Add support to select the clock source for CAN Protocol Engine (PE).
It's SoC Implementation dependent. Refer to RM for detailed definition
of each SoC. We select clock source 1 (peripheral clock) by default in
driver now, this patch adds support to parse the clock source from the DT.

Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Aisheng Dong ca10989632 can: flexcan: implement can Runtime PM
Flexcan will be disabled during suspend if no wakeup function required and
enabled after resume accordingly. During this period, we could explicitly
disable clocks.
Since PM is optional, the clock is enabled at probe to guarante the
clock is running when PM is not enabled in the kernel.

Implement Runtime PM which will:
1) Without CONFIG_PM, clock is running whether Flexcan up or down.
2) With CONFIG_PM, clock enabled while Flexcan up and disabled when
   Flexcan down.
3) Disable clock when do system suspend and enable clock while system
   resume.
4) Make Power Domain framework be able to shutdown the corresponding
   power domain of this device.

Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Colin Ian King 64d6ce8fe4 can: xilinx_can: clean up indentation issue
A statement is indented one level too deep, fix this.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Appana Durga Kedareswara rao c223da6893 can: xilinx_can: Add support for CANFD FD frames
CANFD IP supports both CAN and CAN FD frames,
Existing driver supports only CAN frames, This patch
adds support for CAN FD frames.

Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Appana Durga Kedareswara rao 8dce7ea41a can: xilinx_can: Add cantype parameter in xcan_devtype_data struct
To differentiate between different CAN IP's this patch adds
cantype enum variable in the xcan_devtype_data structure

Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Appana Durga Kedareswara rao 3281b380ec can: xilinx_can: Fix flags field initialization for axi can and canps
AXI CAN IP and CANPS IP supports tx fifo empty feature, this patch updates
the flags field for the same.

Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Appana Durga Kedareswara rao c942a575b9 can: xilinx_can: Fix kernel doc warnings
This patch fixes below kernel doc warnings
warning: Function parameter or member 'priv' not described in
'xcan_write_frame'
warning: Function parameter or member 'skb' not described in
'xcan_start_xmit_fifo'
warning: Function parameter or member 'ndev' not described in
'xcan_start_xmit_fifo'
warning: Function parameter or member 'skb' not described in
'xcan_start_xmit_mailbox'
warning: Function parameter or member 'ndev' not described in
'xcan_start_xmit_mailbox'
warning: Function parameter or member 'priv' not described in
'xcan_rx_fifo_get_next_frame'

Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Appana Durga Kedareswara rao d38f9180da can: xilinx_can: Fix style issues
This patch fixes below checkpatch warnings and checks in the driver.

CHECK: Alignment should match open parenthesis
+       void (*write_reg)(const struct xcan_priv *priv, enum xcan_reg reg,
+                       u32 val);

CHECK: Alignment should match open parenthesis
+static void xcan_write_reg_le(const struct xcan_priv *priv, enum xcan_reg reg,
+                       u32 val)

CHECK: Alignment should match open parenthesis
+static void xcan_write_reg_be(const struct xcan_priv *priv, enum xcan_reg reg,
+                       u32 val)

CHECK: Alignment should match open parenthesis
+       netdev_dbg(ndev, "BRPR=0x%08x, BTR=0x%08x\n",
+                       priv->read_reg(priv, XCAN_BRPR_OFFSET),

CHECK: Alignment should match open parenthesis
+                       netdev_warn(ndev,
+                               "timed out for correct mode\n");

CHECK: Alignment should match open parenthesis
+       netdev_dbg(ndev, "status:#x%08x\n",
+                       priv->read_reg(priv, XCAN_SR_OFFSET));

CHECK: spaces preferred around that '-' (ctx:VxV)
+                       (CAN_EFF_ID_BITS-CAN_SFF_ID_BITS)) <<
                                        ^

CHECK: Alignment should match open parenthesis
+       netdev_dbg(ndev, "%s: error status register:0x%x\n",
+                       __func__, priv->read_reg(priv, XCAN_ESR_OFFSET));

WARNING: line over 80 characters
+                       offset = XCAN_RXMSG_2_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);

WARNING: line over 80 characters
+                       offset = XCAN_RXMSG_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);

WARNING: line over 80 characters
+               while ((isr & XCAN_IXR_TXOK_MASK) && !WARN_ON(++retries == 100)) {

WARNING: line over 80 characters
+                       priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXOK_MASK);

CHECK: Alignment should match open parenthesis
+               netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+                               __func__, ret);

CHECK: Alignment should match open parenthesis
+       ret = request_irq(ndev->irq, xcan_interrupt, priv->irq_flags,
+                       ndev->name, ndev);

CHECK: Alignment should match open parenthesis
+static int xcan_get_berr_counter(const struct net_device *ndev,
+                                       struct can_berr_counter *bec)

CHECK: Alignment should match open parenthesis
+               netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+                               __func__, ret);

CHECK: Please don't use multiple blank lines
+
+

CHECK: Alignment should match open parenthesis
+               netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+                       __func__, ret);`

Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Dan Murphy 5443c226ba can: tcan4x5x: Add tcan4x5x driver to the kernel
Add the TCAN4x5x SPI CAN driver.

This device uses the Bosch MCAN IP core along with a SPI interface map.
Register to the MCAN common core code to manage the MCAN IP.

This device has a special method to indicate a write/read operation on
the data payload.

Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Dan Murphy 441ac34016 can: m_can: Rename m_can_priv to m_can_classdev
Rename the common m_can_priv class structure to m_can_classdev as this
is more descriptive.

Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Dan Murphy f524f829b7 can: m_can: Create a m_can platform framework
Create a m_can platform framework that peripheral
devices can register to and use common code and register sets.
The peripheral devices may provide read/write and configuration
support of the IP.

Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Dan Murphy 69652195b6 can: m_can: Fix checkpatch issues on existing code
Fix checkpatch issues found during the m_can framework creation, before
framework creation in the following patches.

Fix these 4 check issues:
CHECK: Unnecessary parentheses around 'cdev->can.state != CAN_STATE_ERROR_WARNING'
	if (psr & PSR_EW &&
	    (cdev->can.state != CAN_STATE_ERROR_WARNING)) {

CHECK: Unnecessary parentheses around 'cdev->can.state != CAN_STATE_ERROR_PASSIVE'
	if ((psr & PSR_EP) &&
	    (cdev->can.state != CAN_STATE_ERROR_PASSIVE)) {

CHECK: Unnecessary parentheses around 'cdev->can.state != CAN_STATE_BUS_OFF'
	if ((psr & PSR_BO) &&
	    (cdev->can.state != CAN_STATE_BUS_OFF)) {

CHECK: Unnecessary parentheses around 'priv->version <= 31'
	if ((priv->version <= 31) && (irqstatus & IR_MRAF) &&
	    (m_can_read(priv, M_CAN_ECR) & ECR_RP)) {

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Gustavo A. R. Silva b07fbf2397 can: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warnings:

drivers/net/can/peak_canfd/peak_pciefd_main.c:668:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/spi/mcp251x.c:875:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:895:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:953:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c: In function ‘pcan_usb_decode_error’:
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (n & PCAN_USB_ERROR_BUS_LIGHT) {
      ^
drivers/net/can/usb/peak_usb/pcan_usb.c:428:2: note: here
  case CAN_STATE_ERROR_WARNING:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.

Notice that in some cases spelling mistakes were fixed.
In other cases, the /* fall through */ comment is placed
at the bottom of the case statement, which is what GCC
is expecting to find.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # for the at91_can.c
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Henning Colliander 26ad340e58 can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices
This patch adds support for Kvaser PCIEcan devices. This includes
support for up to 4 CAN channels on a single card, depending on device.

Signed-off-by: Henning Colliander <henning.colliander@evidente.se>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:53 +02:00
Gustavo A. R. Silva d9e5d174ad can: kvaser_usb: Use struct_size() in alloc_candev()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = alloc(sizeof(struct foo) + count * sizeof(void *));

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = alloc(struct_size(instance, entry, count));

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:53 +02:00
Ji-Ze Hong (Peter Hong) 2d91fdccad can: sja1000: f81601: add Fintek F81601 support
This patch add support for Fintek PCIE to 2 CAN controller support

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:30:37 +02:00
Marc Kleine-Budde 4dfc39e1b6 can: sja1000: Makefile/Kconfig: sort alphabetically
This patch sorts the drivers in the Makefile alphabetically and arranges
the Kconfig file accordingly.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 08:50:18 +02:00
Fuqian Huang 233cc605a2 net/can: using dev_get_drvdata directly
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-05 15:24:41 -07:00
Linus Torvalds c884d8ac7f SPDX update for 5.2-rc6
Another round of SPDX updates for 5.2-rc6
 
 Here is what I am guessing is going to be the last "big" SPDX update for
 5.2.  It contains all of the remaining GPLv2 and GPLv2+ updates that
 were "easy" to determine by pattern matching.  The ones after this are
 going to be a bit more difficult and the people on the spdx list will be
 discussing them on a case-by-case basis now.
 
 Another 5000+ files are fixed up, so our overall totals are:
 	Files checked:            64545
 	Files with SPDX:          45529
 
 Compared to the 5.1 kernel which was:
 	Files checked:            63848
 	Files with SPDX:          22576
 This is a huge improvement.
 
 Also, we deleted another 20000 lines of boilerplate license crud, always
 nice to see in a diffstat.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
 kbsjBGEJpLbMRB2krnaU
 =RMcT
 -----END PGP SIGNATURE-----

Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx

Pull still more SPDX updates from Greg KH:
 "Another round of SPDX updates for 5.2-rc6

  Here is what I am guessing is going to be the last "big" SPDX update
  for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
  that were "easy" to determine by pattern matching. The ones after this
  are going to be a bit more difficult and the people on the spdx list
  will be discussing them on a case-by-case basis now.

  Another 5000+ files are fixed up, so our overall totals are:
	Files checked:            64545
	Files with SPDX:          45529

  Compared to the 5.1 kernel which was:
	Files checked:            63848
	Files with SPDX:          22576

  This is a huge improvement.

  Also, we deleted another 20000 lines of boilerplate license crud,
  always nice to see in a diffstat"

* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
  ...
2019-06-21 09:58:42 -07:00
Thomas Gleixner d2912cb15b treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:55 +02:00
Thomas Gleixner aaa7cb268c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the version 2 of the gnu general public
  license as published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 10 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.259525894@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:52 +02:00
Linus Torvalds da0f382029 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:
 "Lots of bug fixes here:

   1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.

   2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
      Crispin.

   3) Use after free in psock backlog workqueue, from John Fastabend.

   4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
      Salem.

   5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.

   6) Network header needs to be set for packet redirect in nfp, from
      John Hurley.

   7) Fix udp zerocopy refcnt, from Willem de Bruijn.

   8) Don't assume linear buffers in vxlan and geneve error handlers,
      from Stefano Brivio.

   9) Fix TOS matching in mlxsw, from Jiri Pirko.

  10) More SCTP cookie memory leak fixes, from Neil Horman.

  11) Fix VLAN filtering in rtl8366, from Linus Walluij.

  12) Various TCP SACK payload size and fragmentation memory limit fixes
      from Eric Dumazet.

  13) Use after free in pneigh_get_next(), also from Eric Dumazet.

  14) LAPB control block leak fix from Jeremy Sowden"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
  lapb: fixed leak of control-blocks.
  tipc: purge deferredq list for each grp member in tipc_group_delete
  ax25: fix inconsistent lock state in ax25_destroy_timer
  neigh: fix use-after-free read in pneigh_get_next
  tcp: fix compile error if !CONFIG_SYSCTL
  hv_sock: Suppress bogus "may be used uninitialized" warnings
  be2net: Fix number of Rx queues used for flow hashing
  net: handle 802.1P vlan 0 packets properly
  tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
  tcp: add tcp_min_snd_mss sysctl
  tcp: tcp_fragment() should apply sane memory limits
  tcp: limit payload size of sacked skbs
  Revert "net: phylink: set the autoneg state in phylink_phy_change"
  bpf: fix nested bpf tracepoints with per-cpu data
  bpf: Fix out of bounds memory access in bpf_sk_storage
  vsock/virtio: set SOCK_DONE on peer shutdown
  net: dsa: rtl8366: Fix up VLAN filtering
  net: phylink: set the autoneg state in phylink_phy_change
  net: add high_order_alloc_disable sysctl/static key
  tcp: add tcp_tx_skb_cache sysctl
  ...
2019-06-17 15:55:34 -07:00
Fabio Estevam eb503004a7 can: flexcan: Remove unneeded registration message
Currently the following message is observed when the flexcan
driver is probed:

flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=23)

The reason for printing 'ptrval' is explained at
Documentation/core-api/printk-formats.rst:

"Pointers printed without a specifier extension (i.e unadorned %p) are
hashed to prevent leaking information about the kernel memory layout. This
has the added benefit of providing a unique identifier. On 64-bit machines
the first 32 bits are zeroed. The kernel will print ``(ptrval)`` until it
gathers enough entropy."

Instead of passing %pK, which can print the correct address, simply
remove the entire message as it is not really that useful.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:54 +02:00
Eugen Hristev 3e82f2f34c can: m_can: implement errata "Needless activation of MRAF irq"
During frame reception while the MCAN is in Error Passive state and the
Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen
that MCAN_IR.MRAF is set although there was no Message RAM access
failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is
generated.

Work around:
The Message RAM Access Failure interrupt routine needs to check whether

    MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.

In this case, reset MCAN_IR.MRAF. No further action is required.
This affects versions older than 3.2.0

Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf
chapter 6.2

Reproducibility: If 2 devices with m_can are connected back to back,
configuring different bitrate on them will lead to interrupt storm on
the receiving side, with error "Message RAM access failure occurred".
Another way is to have a bad hardware connection. Bad wire connection
can lead to this issue as well.

This patch fixes the issue according to provided workaround.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:54 +02:00
Sean Nyekjaer 35b7fa4d07 can: mcp251x: add support for mcp25625
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.

This patch adds support for the mcp25625 to the existing mcp251x driver.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:53 +02:00
Anssi Hannula 904044dd8f can: xilinx_can: use correct bittiming_const for CAN FD core
Commit 9e5f1b273e ("can: xilinx_can: add support for Xilinx CAN FD
core") added a new can_bittiming_const structure for CAN FD cores that
support larger values for tseg1, tseg2, and sjw than previous Xilinx CAN
cores, but the commit did not actually take that into use.

Fix that.

Tested with CAN FD core on a ZynqMP board.

Fixes: 9e5f1b273e ("can: xilinx_can: add support for Xilinx CAN FD core")
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:53 +02:00
Joakim Zhang 247e5356a7 can: flexcan: fix timeout when set small bitrate
Current we can meet timeout issue when setting a small bitrate like
10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock =
30MHZ):

| root@imx6ul7d:~# ip link set can0 up type can bitrate 10000

A link change request failed with some changes committed already.
Interface can0 may have been left with an inconsistent configuration,
please check.

| RTNETLINK answers: Connection timed out

It is caused by calling of flexcan_chip_unfreeze() timeout.

Originally the code is using usleep_range(10, 20) for unfreeze
operation, but the patch (8badd65 can: flexcan: avoid calling
usleep_range from interrupt context) changed it into udelay(10) which is
only a half delay of before, there're also some other delay changes.

After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue.

Meanwhile, Rasmus Villemoes reported that even with a timeout of 100,
flexcan_probe() fails on the MPC8309, which requires a value of at least
140 to work reliably. 250 works for everyone.

Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:53 +02:00
Alexander Dahl 0ed89d777d can: usb: Kconfig: Remove duplicate menu entry
This seems to have slipped in by accident when sorting the entries.

Fixes: ffbdd9172e
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:53 +02:00
Thomas Gleixner 4d8bc51069 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 412
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 2 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.858563475@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:14 +02:00
Thomas Gleixner 35e62ae830 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 344
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the version 2 of the gnu general public
  license as published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 15 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.427740574@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:07 +02:00
Thomas Gleixner 2b72c9e36c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 340
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 15 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.052642892@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:07 +02:00
Thomas Gleixner 8e8e69d67e treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 285
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 100 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:36:37 +02:00
Thomas Gleixner dd2878aace treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 198
Based on 1 normalized pattern(s):

  this software may be distributed under the terms of the gnu general
  public license gpl version 2 as distributed in the copying file from
  the main directory of the linux kernel source

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 1 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.816396794@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:29:22 -07:00
Thomas Gleixner 935912c538 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 164
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not write to the free
  software foundation inc 51 franklin street fifth floor boston ma
  02110 1301 usa

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 12 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.745497013@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:38 -07:00
Thomas Gleixner c942fddf87 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157
Based on 3 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version [author] [kishon] [vijay] [abraham]
  [i] [kishon]@[ti] [com] this program is distributed in the hope that
  it will be useful but without any warranty without even the implied
  warranty of merchantability or fitness for a particular purpose see
  the gnu general public license for more details

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version [author] [graeme] [gregory]
  [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
  [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
  [hk] [hemahk]@[ti] [com] this program is distributed in the hope
  that it will be useful but without any warranty without even the
  implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1105 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:37 -07:00
Thomas Gleixner 2874c5fd28 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:32 -07:00
Thomas Gleixner 1ccea77e2a treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details you
  should have received a copy of the gnu general public license along
  with this program if not see http www gnu org licenses

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details [based]
  [from] [clk] [highbank] [c] you should have received a copy of the
  gnu general public license along with this program if not see http
  www gnu org licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 355 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 11:28:45 +02:00
Thomas Gleixner ec8f24b7fa treewide: Add SPDX license identifier - Makefile/Kconfig
Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 10:50:46 +02:00
Arnd Bergmann a2ae6da025 peak_usb: fix clang build warning
Clang points out undefined behavior when building the pcan_usb_pro driver:

drivers/net/can/usb/peak_usb/pcan_usb_pro.c:136:15: error: passing an object that undergoes default argument promotion to 'va_start' has undefined behavior [-Werror,-Wvarargs]

Changing the function prototype to avoid argument promotion in the
varargs call avoids the warning, and should make this well-defined.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-07 09:39:46 -08:00
Uwe Kleine-König a55234dabe can: flexcan: fix NULL pointer exception during bringup
Commit cbffaf7aa0 ("can: flexcan: Always use last mailbox for TX")
introduced a loop letting i run up to (including) ARRAY_SIZE(regs->mb)
and in the body accessed regs->mb[i] which is an out-of-bounds array
access that then resulted in an access to an reserved register area.

Later this was changed by commit 0517961ccd ("can: flexcan: Add
provision for variable payload size") to iterate a bit differently but
still runs one iteration too much resulting to call

	flexcan_get_mb(priv, priv->mb_count)

which results in a WARN_ON and then a NULL pointer exception. This
only affects devices compatible with "fsl,p1010-flexcan",
"fsl,imx53-flexcan", "fsl,imx35-flexcan", "fsl,imx25-flexcan",
"fsl,imx28-flexcan", so newer i.MX SoCs are not affected.

Fixes: cbffaf7aa0 ("can: flexcan: Always use last mailbox for TX")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= 4.20
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-01-22 11:35:33 +01:00
YueHaibing 7873e98c61 can: flexcan: fix 'passing zero to ERR_PTR()' warning
Fix a static code checker warning:
drivers/net/can/flexcan.c:1435 flexcan_setup_stop_mode() warn: passing zero to 'PTR_ERR'

Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-01-22 11:34:17 +01:00
Manfred Schlaegl 7b12c8189a can: dev: __can_get_echo_skb(): fix bogous check for non-existing skb by removing it
This patch revert commit 7da11ba5c5
("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")

After introduction of this change we encountered following new error
message on various i.MX plattforms (flexcan):

| flexcan 53fc8000.can can0: __can_get_echo_skb: BUG! Trying to echo non
| existing skb: can_priv::echo_skb[0]

The introduction of the message was a mistake because
priv->echo_skb[idx] = NULL is a perfectly valid in following case: If
CAN_RAW_LOOPBACK is disabled (setsockopt) in applications, the pkt_type
of the tx skb's given to can_put_echo_skb is set to PACKET_LOOPBACK. In
this case can_put_echo_skb will not set priv->echo_skb[idx]. It is
therefore kept NULL.

As additional argument for revert: The order of check and usage of idx
was changed. idx is used to access an array element before checking it's
boundaries.

Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Fixes: 7da11ba5c5 ("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-01-22 11:18:34 +01:00
Pankaj Bansal 6cbf76028d can: flexcan: split the Message Buffer RAM area
The message buffer RAM area is not a contiguous 1KB area but 2 partitions
of 512 bytes each. Till now, we used Message buffers with payload size 8
bytes, which translates to 32 MBs per partition and no spare space is left
in any partition.
However, in upcoming SOC LX2160A the message buffers can have payload size
64 bytes. This results in less than 32 MBs per partition and some empty
area is left at the end of each partition.This empty area should not be
accessed.
Therefore, split the Message Buffer RAM area into two partitions.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:52:25 +01:00
Pankaj Bansal 0517961ccd can: flexcan: Add provision for variable payload size
Till now the flexcan module supported 8 byte payload size as per CAN 2.0
specifications. But now upcoming flexcan module in NXP LX2160A SOC
supports CAN FD protocol too. The Message buffers need to be configured
to have payload size 64 bytes.

Therefore, added provision in the driver for payload size to be 64 bytes.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:51:44 +01:00
Pankaj Bansal 5156c7b11f can: flexcan: move rx_offload_add() from flexcan_probe() to flexcan_open()
rx offload depends on number of message buffers, which in turn depends
on messgae buffer size. with the upcoming LX2160A SOC the message buffer
size can be configured to 72 bytes if it were to be used in CAN FD mode.

The current mode in which the flexcan is being operated is known at the
time of flexcan_open() but not at the time of flexcan_probe().

Therefore, move the rx_offload_add() from flexcan_probe() to
flexcan_open(). correspondingly, move rx_offload_delete() from
flexcan_remove() to flexcan_close().

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:51:44 +01:00
Pankaj Bansal 7ad0f53a39 can: flexcan: flexcan_chip_start(): enable loopback mode in flexcan
Self reception disable bit needs to be cleared for loopback mode to work
in flexcan.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:51:44 +01:00
Aisheng Dong de3578c198 can: flexcan: add self wakeup support
If wakeup is enabled, enter stop mode, else enter disabled mode. Self wake
can only work on stop mode.

Starting from IMX6, the flexcan stop mode control bits is SoC specific,
move it out of IP driver and parse it from devicetree.

Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:51:43 +01:00
Marc Kleine-Budde c982a3ca49 can: flexcan: flexcan_chip_start(): adjust comment to match the code
With the conversion of the flexcan driver to support both timestamp and
FIFO mode the setup of the MCR register ("enable fifo") has been moved.

This patch moves the comment too, in order to match the code again.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:51:43 +01:00
Marc Kleine-Budde 22233f7bf2 can: flexcan: FLEXCAN_IFLAG_MB: add () around macro argument
This patch fixes the following checkpatch warning:

| Macro argument 'x' may be better as '(x)' to avoid precedence issues

Fixes: cbffaf7aa0 ("can: flexcan: Always use last mailbox for TX")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:53 +01:00
Marc Kleine-Budde bc8ad65151 can: flexcan: flexcan_irq(): fix indention
The patch fixes the indention by replacing space by tabs, as noted by
checkpatch:

| ERROR: code indent should use tabs where possible
| #980: FILE: drivers/net/can/flexcan.c:980:

Fixes: da49a8075c ("can: flexcan: implement error passive state quirk")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:53 +01:00
Marc Kleine-Budde 9dc1ee1184 can: flexcan: flexcan_start_xmit(): fix indention
This patch fixes the indentio nin flexcan_start_xmit() by alligning the
code to the opening parenthesis.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:53 +01:00
Pankaj Bansal 0f8af56f74 can: flexcan: enable flexcan for all architectures
flexcan is an IP module independent of the SOC architecture.
Therefore, enable it for all architectures.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:53 +01:00
Kuninori Morimoto e3dfddbf0d can: rcar: add SPDX identifiers to Kconfig and Makefile
This patch adds SPDX-License-Identifier to Kconfig and Makefile.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:53 +01:00
Wolfram Sang 7af42e50f6 can: rcar: use SPDX identifier for Renesas drivers
Adopt the SPDX license identifier headers to ease license compliance
management.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:53 +01:00
Flavio Suligoi 06a3f31ae2 can: sja1000: plx_pci: add support for ASEM CAN raw device
This patch adds support for ASEM opto-isolated dual channels
CAN raw device (http://www.asem.it)

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:53 +01:00
Shubhrajyoti Datta 0db9071353 can: xilinx: add can 2.0 support
Add support for can 2.0.

Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:52 +01:00
YueHaibing 81de0cd60f can: xilinx: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.

Found by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:52 +01:00
Colin Ian King 3b17d41754 can: ucan: fix spelling mistake: "resumbmitting" -> "resubmitting"
Trivial fix to spelling mistake in netdev_dbg error message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-28 16:19:52 +01:00
David S. Miller f2be6d710d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2018-11-19 10:55:00 -08:00
Oleksij Rempel d788905f68 can: flexcan: use can_rx_offload_queue_sorted() for flexcan_irq_bus_*()
Currently, in case of bus error, driver will generate error message and put
in the tail of the message queue. To avoid confusions, this change should
place the bus related messages in proper order.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:33:33 +01:00
Oleksij Rempel 4530ec36bb can: rx-offload: rename can_rx_offload_irq_queue_err_skb() to can_rx_offload_queue_tail()
This function has nothing todo with error.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:33:32 +01:00
Oleksij Rempel ed72bc8bcb can: flexcan: handle tx-complete CAN frames via rx-offload infrastructure
Current flexcan driver will put TX-ECHO in regular unsorted way, in
this case TX-ECHO can come after the response to the same TXed message.
In some cases, for example for J1939 stack, things will break.
This patch is using new rx-offload API to put the messages just in the
right place.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:33:32 +01:00
Oleksij Rempel 55059f2b7f can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions
Current CAN framework can't guarantee proper/chronological order
of RX and TX-ECHO messages. To make this possible, drivers should use
this functions instead of can_get_echo_skb().

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:49 +01:00
Marc Kleine-Budde 7da11ba5c5 can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb
Prior to echoing a successfully transmitted CAN frame (by calling
can_get_echo_skb()), CAN drivers have to put the CAN frame (by calling
can_put_echo_skb() in the transmit function). These put and get function
take an index as parameter, which is used to identify the CAN frame.

A driver calling can_get_echo_skb() with a index not pointing to a skb
is a BUG, so add an appropriate error message.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:46 +01:00
Marc Kleine-Budde e7a6994d04 can: dev: __can_get_echo_skb(): Don't crash the kernel if can_priv::echo_skb is accessed out of bounds
If the "struct can_priv::echo_skb" is accessed out of bounds would lead
to a kernel crash. Better print a sensible warning message instead and
try to recover.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:43 +01:00
Marc Kleine-Budde 200f5c49f7 can: dev: __can_get_echo_skb(): replace struct can_frame by canfd_frame to access frame length
This patch replaces the use of "struct can_frame::can_dlc" by "struct
canfd_frame::len" to access the frame's length. As it is ensured that
both structures have a compatible memory layout for this member this is
no functional change. Futher, this compatibility is documented in a
comment.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:40 +01:00
Marc Kleine-Budde a4310fa2f2 can: dev: can_get_echo_skb(): factor out non sending code to __can_get_echo_skb()
This patch factors out all non sending parts of can_get_echo_skb() into
a seperate function __can_get_echo_skb(), so that it can be re-used in
an upcoming patch.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:34 +01:00
Marc Kleine-Budde e05237f9da can: flexcan: remove not needed struct flexcan_priv::tx_mb and struct flexcan_priv::tx_mb_idx
The previous patch changes the TX path to always use the last mailbox
regardless of the used offload scheme (rx-fifo or timestamp based). This
means members "tx_mb" and "tx_mb_idx" of the struct flexcan_priv don't
depend on the offload scheme, so replace them by compile time constants.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:29 +01:00
Alexander Stein cbffaf7aa0 can: flexcan: Always use last mailbox for TX
Essentially this patch moves the TX mailbox to position 63, regardless
of timestamp based offloading or RX FIFO. So mainly the iflag register
usage regarding TX has changed. The rest is consolidating RX FIFO and
timestamp offloading as they now use both the same TX mailbox.

The reason is a very annoying behavior regarding sending RTR frames when
_not_ using RX FIFO:

If a TX mailbox sent a RTR frame it becomes a RX mailbox. For that
reason flexcan_irq disables the TX mailbox again. But if during the time
the RTR was sent and the TX mailbox is disabled a new CAN frames is
received, it is lost without notice. The reason is that so-called
"Move-in" process starts from the lowest mailbox which happen to be a TX
mailbox set to EMPTY.

Steps to reproduce (I used an imx7d):
1. generate regular bursts of messages
2. send a RTR from flexcan with higher priority than burst messages every
   1ms, e.g. cangen -I 0x100 -L 0 -g 1 -R can0
3. notice a lost message without notification after some seconds

When running an iperf in parallel this problem is occurring even more
frequently. Using filters is not possible as at least one single CAN-ID
is allowed. Handling the TX MB during RX is also not possible as there
is no race-free disable of RX MB.

There is still a slight window when the described problem can occur. But
for that all RX MB must be in use which is essentially next to an
overrun. Still there will be no indication if it ever occurs.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:23 +01:00
Pankaj Bansal 5178b7cd8e can: flexcan: Unlock the MB unconditionally
Unlock the MB irrespective of reception method being FIFO or timestamp
based. It is optional but recommended to unlock Mailbox as soon as
possible and make it available for reception.

Reported-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:12 +01:00
Lukas Wunner f164d0204b can: hi311x: Use level-triggered interrupt
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing.  Bus state is "active".
Bringing the interface down and back up reconvenes the reception.  The
issue is not observed when the hi3110 is the sole device on the SPI bus.

Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.

Unfortunately the hi3110 datasheet is mum on the trigger type.  The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:08 +01:00
Fabrizio Castro 68c8d209cd can: rcar_can: Fix erroneous registration
Assigning 2 to "renesas,can-clock-select" tricks the driver into
registering the CAN interface, even though we don't want that.
This patch improves one of the checks to prevent that from happening.

Fixes: 862e2b6af9 ("can: rcar_can: support all input clocks")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:08 +01:00
YueHaibing ff1f19d56c can: ucan: remove duplicated include from ucan.c
Remove duplicated include.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:07 +01:00
YueHaibing 207681fc5f can: ucan: remove set but not used variable 'udev'
Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/can/usb/ucan.c: In function 'ucan_disconnect':
drivers/net/can/usb/ucan.c:1578:21: warning:
 variable 'udev' set but not used [-Wunused-but-set-variable]
  struct usb_device *udev;

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:07 +01:00
Jimmy Assarsson e13fb9b37c can: kvaser_usb: Fix accessing freed memory in kvaser_usb_start_xmit()
The call to can_put_echo_skb() may result in the skb being freed. The skb
is later used in the call to dev->ops->dev_frame_to_cmd().

This is avoided by moving the call to can_put_echo_skb() after
dev->ops->dev_frame_to_cmd().

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:20:03 +01:00
Jimmy Assarsson 9521726064 can: kvaser_usb: Fix potential uninitialized variable use
If alloc_can_err_skb() fails, cf is never initialized.
Move assignment of cf inside check.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-11-09 17:19:57 +01:00
David Ahern d0522f1cd2 net: Add extack argument to rtnl_create_link
Add extack arg to rtnl_create_link and add messages for invalid
number of Tx or Rx queues.

Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-06 15:00:45 -08:00
David S. Miller 6effee6840 can: Remove SKB list assumptions in rx-offload.c
Eliminate code which assumes that SKBs and skb_queue_head objects
can be cast to eachother during list processing.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-10 10:06:54 -07:00
Linus Torvalds 9a76aba02a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "Highlights:

   - Gustavo A. R. Silva keeps working on the implicit switch fallthru
     changes.

   - Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
     Luca Coelho.

   - Re-enable ASPM in r8169, from Kai-Heng Feng.

   - Add virtual XFRM interfaces, which avoids all of the limitations of
     existing IPSEC tunnels. From Steffen Klassert.

   - Convert GRO over to use a hash table, so that when we have many
     flows active we don't traverse a long list during accumluation.

   - Many new self tests for routing, TC, tunnels, etc. Too many
     contributors to mention them all, but I'm really happy to keep
     seeing this stuff.

   - Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.

   - Lots of cleanups and fixes in L2TP code from Guillaume Nault.

   - Add IPSEC offload support to netdevsim, from Shannon Nelson.

   - Add support for slotting with non-uniform distribution to netem
     packet scheduler, from Yousuk Seung.

   - Add UDP GSO support to mlx5e, from Boris Pismenny.

   - Support offloading of Team LAG in NFP, from John Hurley.

   - Allow to configure TX queue selection based upon RX queue, from
     Amritha Nambiar.

   - Support ethtool ring size configuration in aquantia, from Anton
     Mikaev.

   - Support DSCP and flowlabel per-transport in SCTP, from Xin Long.

   - Support list based batching and stack traversal of SKBs, this is
     very exciting work. From Edward Cree.

   - Busyloop optimizations in vhost_net, from Toshiaki Makita.

   - Introduce the ETF qdisc, which allows time based transmissions. IGB
     can offload this in hardware. From Vinicius Costa Gomes.

   - Add parameter support to devlink, from Moshe Shemesh.

   - Several multiplication and division optimizations for BPF JIT in
     nfp driver, from Jiong Wang.

   - Lots of prepatory work to make more of the packet scheduler layer
     lockless, when possible, from Vlad Buslov.

   - Add ACK filter and NAT awareness to sch_cake packet scheduler, from
     Toke Høiland-Jørgensen.

   - Support regions and region snapshots in devlink, from Alex Vesker.

   - Allow to attach XDP programs to both HW and SW at the same time on
     a given device, with initial support in nfp. From Jakub Kicinski.

   - Add TLS RX offload and support in mlx5, from Ilya Lesokhin.

   - Use PHYLIB in r8169 driver, from Heiner Kallweit.

   - All sorts of changes to support Spectrum 2 in mlxsw driver, from
     Ido Schimmel.

   - PTP support in mv88e6xxx DSA driver, from Andrew Lunn.

   - Make TCP_USER_TIMEOUT socket option more accurate, from Jon
     Maxwell.

   - Support for templates in packet scheduler classifier, from Jiri
     Pirko.

   - IPV6 support in RDS, from Ka-Cheong Poon.

   - Native tproxy support in nf_tables, from Máté Eckl.

   - Maintain IP fragment queue in an rbtree, but optimize properly for
     in-order frags. From Peter Oskolkov.

   - Improvde handling of ACKs on hole repairs, from Yuchung Cheng"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
  bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
  hv/netvsc: Fix NULL dereference at single queue mode fallback
  net: filter: mark expected switch fall-through
  xen-netfront: fix warn message as irq device name has '/'
  cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
  net: dsa: mv88e6xxx: missing unlock on error path
  rds: fix building with IPV6=m
  inet/connection_sock: prefer _THIS_IP_ to current_text_addr
  net: dsa: mv88e6xxx: bitwise vs logical bug
  net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
  ieee802154: hwsim: using right kind of iteration
  net: hns3: Add vlan filter setting by ethtool command -K
  net: hns3: Set tx ring' tc info when netdev is up
  net: hns3: Remove tx ring BD len register in hns3_enet
  net: hns3: Fix desc num set to default when setting channel
  net: hns3: Fix for phy link issue when using marvell phy driver
  net: hns3: Fix for information of phydev lost problem when down/up
  net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
  net: hns3: Add support for serdes loopback selftest
  bnxt_en: take coredump_record structure off stack
  ...
2018-08-15 15:04:25 -07:00
Linus Torvalds c07b3682cd LED updates for 4.19-rc1
-----BEGIN PGP SIGNATURE-----
 
 iJEEABYIADkWIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCW3HajRscamFjZWsuYW5h
 c3pld3NraUBnbWFpbC5jb20ACgkQYhBsURv0pdvxAwEA+qS5O9ByxlhT+BUC4ck6
 nIy0ITOCXP8ySoo8VVhzjikBAPrb9lFYGvHqzKN4dYtnSILPmlTSf1t1flng2Zev
 NfoE
 =lNwq
 -----END PGP SIGNATURE-----

Merge tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED updates from Jacek Anaszewski:
 "LED triggers improvements make the biggest part of this pull request.
  The most striking ones, that allowed for nice cleanups in the triggers
  are:

   - centralized handling of creation and removal of trigger sysfs
     attributes via attribute group

   - addition of module_led_trigger() helper

  The other things that need to be mentioned:

  New features and improvements to existing LED class drivers:

   - lt3593: add DT support, switch to gpiod interface

   - lm3692x: support LED sync configuration, change OF calls to fwnode
     calls

   - apu: modify PC Engines apu/apu2 driver to support apu3

  Change in the drivers/net/can/led.c:

   - mark led trigger as broken since it's in the way for the further
     cleanups. It implements a subset of the netdev trigger and an Ack
     is needed from someone who can actually test and confirm that the
     netdev trigger works for can devices"

* tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits)
  leds: ns2: Change unsigned to unsigned int
  usb: simplify usbport trigger
  leds: gpio trigger: simplifications from core changes
  leds: backlight trigger: simplifications from core changes
  leds: activity trigger: simplifications from core changes
  leds: default-on trigger: make use of module_led_trigger()
  leds: heartbeat trigger: simplifications from core changes
  leds: oneshot trigger: simplifications from core changes
  leds: transient trigger: simplifications from core changes
  leds: timer trigger: simplifications from core changes
  leds: netdev trigger: simplifications from core changes
  leds: triggers: new function led_set_trigger_data()
  leds: triggers: define module_led_trigger helper
  leds: triggers: handle .trigger_data and .activated() in the core
  leds: triggers: add device attribute support
  leds: triggers: let struct led_trigger::activate() return an error code
  leds: triggers: make the MODULE_LICENSE string match the actual license
  leds: lm3692x: Support LED sync configuration
  dt: bindings: lm3692x: Update binding for LED sync control
  leds: lm3692x: Change DT calls to fwnode calls
  ...
2018-08-14 13:07:22 -07:00
David S. Miller 89b1698c93 Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/net
The BTF conflicts were simple overlapping changes.

The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-02 10:55:32 -07:00
Anton Vasilyev 72c05f32f4 can: ems_usb: Fix memory leak on ems_usb_disconnect()
ems_usb_probe() allocates memory for dev->tx_msg_buffer, but there
is no its deallocation in ems_usb_disconnect().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-30 11:04:27 +02:00
Jimmy Assarsson 1f6ed42c74 can: kvaser_usb: Simplify struct kvaser_cmd_cardinfo
serial_number_high can be removed from the struct since it is never used in
the USBcan II firmware.

Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:19 +02:00
Jimmy Assarsson aec5fb2268 can: kvaser_usb: Add support for Kvaser USB hydra family
This patch adds support for a new Kvaser USB family, denoted hydra.
The hydra family currently contains USB devices with one CAN channel
up to five. There are devices with and without CAN FD support.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Nicklas Johansson <extnj@kvaser.com>
Signed-off-by: Martin Henriksson <mh@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:19 +02:00
Jimmy Assarsson 7259124eac can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c
First part of adding support for Kvaser USB device family "hydra".

Split kvaser_usb.c into kvaser_usb/kvaser_usb{.h,_core.c,_leaf.c}.

kvaser_usb_core.c contains common functionality, such as USB
writing/reading and allocation of netdev.
kvaser_usb_leaf.c contains device specific code, used in
kvaser_usb_core.c.

struct kvaser_usb_dev_ops contains device specific functions that are
common for all devices in the family. While, struct kvaser_usb_dev_cfg
describes the device configurations in terms of CAN clock frequency,
timestamp frequency and CAN controller bittiming constants.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:19 +02:00
Jimmy Assarsson e0543f2479 can: kvaser_usb: Add SPDX GPL-2.0 license identifier
Add SPDX GPL-2.0 license identifier to kvaser_usb.c.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:19 +02:00
Jimmy Assarsson 2b049c1500 can: kvaser_usb: Fix typos
Fix some typos. Change can to CAN, when referring to
Controller Area Network.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:19 +02:00
Jimmy Assarsson 6ba0b9294b can: kvaser_usb: Improve logging messages
Replace dev->udev->dev.parent with &dev->intf->dev, when it is the
first argument passed to dev_* logging function call.

This will result in:
kvaser_usb 1-2:1.0: Format error
compared to
usb 1-2: Format error

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:19 +02:00
Jimmy Assarsson 7c47801461 can: kvaser_usb: Refactor kvaser_usb_init_one()
Replace first parameter in kvaser_usb_init_one() with a pointer to
struct kvaser_usb.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:19 +02:00
Jimmy Assarsson 99ce1bc174 can: kvaser_usb: Refactor kvaser_usb_get_endpoints()
Replace parameters with struct kvaser_usb pointer. Rename the function
from kvaser_usb_get_endpoints() to kvaser_usb_setup_endpoints().

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:19 +02:00
Jimmy Assarsson 0e30619fd6 can: kvaser_usb: Add pointer to struct usb_interface into struct kvaser_usb
Add pointer to struct usb_interface into struct kvaser_usb.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Jimmy Assarsson 75d2b4c3e3 can: kvaser_usb: Replace USB timeout constants with one define
Replace USB timeout constants used when sending and receiving, with a
single constant.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Jimmy Assarsson f741f93855 can: kvaser_usb: Rename message/msg to command/cmd
Rename message to command and msg to cmd, where appropriate. To make the
code more readable and to better match Kvaser's Linux drivers.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Jimmy Assarsson 2375722201 can: kvaser_usb: Remove unused commands and defines
Remove unused commands:
  struct kvaser_msg_cardinfo2
  struct leaf_msg_tx_acknowledge
  struct usbcan_msg_tx_acknowledge

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Jimmy Assarsson deaa1c984b can: kvaser_usb: Remove unnecessary return
Remove unnecessary return at end of void function.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Stephane Grosjean 5592cd0390 can: peak_canfd: rearrange the way resources are released
This patch improves the sequence the resources are released by, first,

- disabling the IRQ in the controller, then by
- resetting the DMA logic, and finally, by
- adding a read cycle to ensure that the above commands have been received

before freeing the system interrupt.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Stephane Grosjean d31f8513f2 can: peak_canfd: fix typo in error message
This patch fixes a typo in the error message in pciefd_can_probe().

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Stephane Grosjean cc5f9bb02e can: peak_canfd: use ndev irq instead of pci_dev one
This cosmetic change should facilitate in the future the use of MSI
rather than legacy INTx interrupts.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Stephane Grosjean f6c740f592 can: peak_canfd: remove useless defined symbols
CANFD_IRQ_SET as well as CANFD_TX_PATH_SET are not used.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Stephane Grosjean 0cccf0abf2 can: peak_canfd: improves 32-bit alignment
The embedded firmware aligns its messages on 32-bit boundaries.
This patch makes sure to browse through the list of received messages
while respecting 32-bit alignment.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:18 +02:00
Gustavo A. R. Silva f805ed8489 can: peak_usb: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Anssi Hannula 9e5f1b273e can: xilinx_can: add support for Xilinx CAN FD core
Add support for Xilinx CAN FD core.

The major difference from the previously supported cores is that there
are TX mailboxes instead of a TX FIFO and the RX FIFO access method is
different.

We only transmit one frame at a time to prevent the HW from reordering
frames (it uses CAN ID priority order).

Support for CAN FD protocol is not added yet.

v2: Removed unnecessary "rx-mode" DT property and wrapped some long
    lines.

Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Anssi Hannula 1598efe57b can: xilinx_can: refactor code in preparation for CAN FD support
Xilinx CAN FD cores are different enough from the previous Zynq and AXI
CAN cores that some refactoring of the driver is needed.

This commit contains most of the required refactoring to existing code
and should not alter behavior on existing supported HW.

The changes are:

- Reading and writing to frame registers is parametrized to allow
  reading/writing a different frame in the future.

- Slightly misleading (as it did not specify *all* the interrupts
  supported by the HW) XCAN_INTR_ALL is replaced with specifying the
  interrupts inline in interrupt enabling code.

- xcan_devtype_data.caps is renamed to xcan_devtype_data.flags to allow
  for flags that define alternative functionality (e.g. mailboxes vs.
  FIFO) instead of purely additive capabilities.

- can_bittiming_const is added to xcan_devtype_data as CAN FD cores will
  have wider setting ranges.

- bus_clk clock name is now determined through xcan_devtype_data instead
  of comparing compatible string in probe().

- xcan_devtype_data is added to xcan_priv to allow flag checks after
  probe().

- XCAN_CAP_WATERMARK is now XCAN_FLAG_TXFEMP. CAN FD cores have
  watermark support but no TXFEMP interrupt, which is what we are
  actually interested in.

- xcan_start_xmit() is split to in two parts to prepare for TX mailboxes
  instead of FIFO in CAN FD cores.

v2: Wrapped some long lines in xcan_write_frame().

Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Anssi Hannula 11ee5fcd6a can: xilinx_can: update stats.tx_bytes after transmission
The driver updates stats.tx_bytes in start_xmit() even though it could
do so in TX interrupt handler.

Change the code to update tx_bytes in the interrupt handler, using the
return value of can_get_echo_skb().

Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Anssi Hannula 6181dbc02b can: xilinx_can: use can_change_state()
Replace some custom code with a call to can_change_state().

This subtly changes the error reporting behavior when both RX and TX
error counters indicate the same state.

Previously, if both RX and TX counters indicated the same state:
- if overall state is PASSIVE, report CAN_ERR_CRTL_RX_PASSIVE
- if overall state is WARNING, report CAN_ERR_CRTL_TX_WARNING or
  CAN_ERR_CRTL_RX_WARNING depending on which counter is higher,
  or CAN_ERR_CRTL_RX_WARNING if the counters have the same value.

After this commit:
- report RX_* or TX_* depending on which counter is higher, or both if
  the counters have exactly the same value.

This behavior is consistent with many other CAN drivers that use this
same code pattern.

Tested with the integrated CAN on Zynq-7000 SoC.

v2: Simplify resolving states as suggested by Andri Yngvason.

Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Anssi Hannula 7e2804aae1 can: xilinx_can: only report warning and passive states on state changes
The xilinx_can driver currently increments error-warning and
error-passive statistics on every error interrupt regardless of whether
the interface was already in the same state. Similarly, the error frame
sent on error interrupts is always sent with
CAN_ERR_CRTL_(RX|TX)_(PASSIVE|WARNING) bit set.

To make the error-warning and error-passive statistics more useful, add
a check to only set the error state when the state has actually been
changed.

Tested with the integrated CAN on Zynq-7000 SoC.

Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Jia-Ju Bai c8d4dea2a8 can: sja1000: Replace mdelay with usleep_range in pcan_add_channels
pcan_add_channels() is never called in atomic context.

pcan_add_channels() is only called by pcan_probe(), which is only set as
".probe" in struct pcmcia_driver.

Despite never getting called from atomic context, pcan_add_channels()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.

This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Jia-Ju Bai 276b7361bb can: sja1000: Replace mdelay with usleep_range in peak_pci_probe
peak_pci_probe() is never called in atomic context.

peak_pci_probe() is set as ".probe" in struct pci_driver.

Despite never getting called from atomic context, peak_pci_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.

This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Fabio Estevam 5b749be31d can: flexcan: Switch to SPDX identifier
Adopt the SPDX license identifier headers to ease license compliance
management.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:17 +02:00
Marc Kleine-Budde fb1e13e6da can: flexcan: fix flexcan_start_xmit()'s return type
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
Luc Van Oostenryck 97f2a5893c can: xilinx: fix xcan_start_xmit()'s return type
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
Luc Van Oostenryck 79b110bb0b can: sun4i: fix sun4ican_start_xmit()'s return type
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
Luc Van Oostenryck 67c2eef22e can: janz-ican3: fix ican3_xmit()'s return type
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.

Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
Zhu Yi 0387090713 can: dev: enable multi-queue for SocketCAN devices
The existing SocketCAN implementation provides alloc_candev() to
allocate a CAN device using a single Tx and Rx queue. This can lead to
priority inversion in case the single Tx queue is already full with low
priority messages and a high priority message needs to be sent while the
bus is fully loaded with medium priority messages.

This problem can be solved by using the existing multi-queue support of
the network subsytem. The commit makes it possible to use multi-queue in
the CAN subsystem in the same way it is used in the Ethernet subsystem
by adding an alloc_candev_mqs() call and accompanying macros. With this
support a CAN device can use multi-queue qdisc (e.g. mqprio) to avoid
the aforementioned priority inversion.

The exisiting functionality of alloc_candev() is the same as before.

CAN devices need to have prioritized multiple hardware queues or are
able to abort waiting for arbitration to make sensible use of
multi-queues.

Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
YueHaibing 8551e71d10 can: dev: use skb_put_zero to simplfy code
use helper skb_put_zero to replace the pattern of skb_put() && memset()

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
Jakob Unterwurzacher 9f2d3eae88 can: ucan: add driver for Theobroma Systems UCAN devices
The UCAN driver supports the microcontroller-based USB/CAN
adapters from Theobroma Systems. There are two form-factors
that run essentially the same firmware:

* Seal: standalone USB stick ( https://www.theobroma-systems.com/seal )

* Mule: integrated on the PCB of various System-on-Modules from
  Theobroma Systems like the A31-µQ7 and the RK3399-Q7
  ( https://www.theobroma-systems.com/rk3399-q7 )

The USB wire protocol has been designed to be as generic and
hardware-indendent as possible in the hope of being useful for
implementation on other microcontrollers.

Signed-off-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
Marc Kleine-Budde ffbdd9172e can: usb: Kconfig/Makefile: sort alphabetically
This patch sorts the entries in the Kconfig and Makefile alphabetically,
so that further contributors can generate patches more easily.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
Colin Ian King b7cc4f3e12 can: cc770: fix spelling mistake: "comptibility" -> "compatibility"
Trivial fix to spelling mistake in module parameter description text

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-27 10:40:16 +02:00
Anssi Hannula 8ebd83bdb0 can: xilinx_can: fix power management handling
There are several issues with the suspend/resume handling code of the
driver:

- The device is attached and detached in the runtime_suspend() and
  runtime_resume() callbacks if the interface is running. However,
  during xcan_chip_start() the interface is considered running,
  causing the resume handler to incorrectly call netif_start_queue()
  at the beginning of xcan_chip_start(), and on xcan_chip_start() error
  return the suspend handler detaches the device leaving the user
  unable to bring-up the device anymore.

- The device is not brought properly up on system resume. A reset is
  done and the code tries to determine the bus state after that.
  However, after reset the device is always in Configuration mode
  (down), so the state checking code does not make sense and
  communication will also not work.

- The suspend callback tries to set the device to sleep mode (low-power
  mode which monitors the bus and brings the device back to normal mode
  on activity), but then immediately disables the clocks (possibly
  before the device reaches the sleep mode), which does not make sense
  to me. If a clean shutdown is wanted before disabling clocks, we can
  just bring it down completely instead of only sleep mode.

Reorganize the PM code so that only the clock logic remains in the
runtime PM callbacks and the system PM callbacks contain the device
bring-up/down logic. This makes calling the runtime PM callbacks during
e.g. xcan_chip_start() safe.

The system PM callbacks now simply call common code to start/stop the
HW if the interface was running, replacing the broken code from before.

xcan_chip_stop() is updated to use the common reset code so that it will
wait for the reset to complete. Reset also disables all interrupts so do
not do that separately.

Also, the device_may_wakeup() checks are removed as the driver does not
have wakeup support.

Tested on Zynq-7000 integrated CAN.

Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:46 +02:00
Anssi Hannula 2f4f0f338c can: xilinx_can: fix incorrect clear of non-processed interrupts
xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of
them is asserted. This does not take into account that some of them
could have been asserted between interrupt status read and interrupt
clear, therefore clearing them without handling them.

Fix the code to only clear those interrupts that it knows are asserted
and therefore going to be processed in xcan_err_interrupt().

Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:46 +02:00
Anssi Hannula 8399799725 can: xilinx_can: fix RX overflow interrupt not being enabled
RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).

Fix that by enabling the RXOFLW interrupt.

Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:46 +02:00
Anssi Hannula 620050d9c2 can: xilinx_can: keep only 1-2 frames in TX FIFO to fix TX accounting
The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.

However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.

Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.

The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
  BUG!, TX FIFO full when queue awake!
messages to be output.

There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.

The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.

Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.

Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.

An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.

v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.

v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.

Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:46 +02:00
Anssi Hannula 877e0b7594 can: xilinx_can: fix recovery from error states not being propagated
The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.

Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:45 +02:00
Anssi Hannula 32852c561b can: xilinx_can: fix RX loop if RXNEMP is asserted without RXOK
If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.

This situation can occur when:

(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.

(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.

I'm able to trigger case (b) by flooding the bus with frames under load.

There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.

Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:45 +02:00
Anssi Hannula 2574fe5451 can: xilinx_can: fix device dropping off bus on RX overrun
The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.

The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.

Remove the software reset.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44f5 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:45 +02:00
Faiz Abbas 54e4a0c486 can: m_can: Move accessing of message ram to after clocks are enabled
MCAN message ram should only be accessed once clocks are enabled.
Therefore, move the call to parse/init the message ram to after
clocks are enabled.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:45 +02:00
Faiz Abbas 1675bee3e7 can: m_can: Fix runtime resume call
pm_runtime_get_sync() returns a 1 if the state of the device is already
'active'. This is not a failure case and should return a success.

Therefore fix error handling for pm_runtime_get_sync() call such that
it returns success when the value is 1.

Also cleanup the TODO for using runtime PM for sleep mode as that is
implemented.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:45 +02:00
Nicholas Mc Guire b5c1a23b17 can: mpc5xxx_can: check of_iomap return before use
of_iomap() can return NULL so that return needs to be checked and NULL
treated as failure. While at it also take care of the missing
of_node_put() in the error path.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit afa17a500a ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:45 +02:00
Roman Fietze 393753b217 can: m_can.c: fix setup of CCCR register: clear CCCR NISO bit before checking can.ctrlmode
Inside m_can_chip_config(), when setting up the new value of the CCCR,
the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON,
CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for
CAN_CTRLMODE_FD_NON_ISO.

This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO,
this mode could never be cleared again.

This fix is only relevant for controllers with version 3.1.x or 3.2.x.
Older versions do not support NISO.

Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:45 +02:00
Stephane Grosjean 5d4c94ed9f can: peak_canfd: fix firmware < v3.3.0: limit allocation to 32-bit DMA addr only
The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards
family is not capable of handling a mix of 32-bit and 64-bit logical
addresses. If the board is equipped with 2 or 4 CAN ports, then such a
situation might lead to a PCIe Bus Error "Malformed TLP" packet
as well as "irq xx: nobody cared" issue.

This patch adds a workaround that requests only 32-bit DMA addresses
when these might be allocated outside of the 4 GB area.

This issue has been fixed in firmware v3.3.0 and next.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-07-23 14:34:45 +02:00
Uwe Kleine-König 30f3b42147 can: mark led trigger as broken
The driver was suggested for deletion as it implements a subset of the
netdev trigger. It's in the way for further cleanups in the trigger
code but doesn't get an Ack by someone who can actually test and confirm
that the netdev trigger works for can devices. So marking as broken to
get forward with the cleanups.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
2018-06-28 21:34:45 +02:00
Kees Cook 6396bb2215 treewide: kzalloc() -> kcalloc()
The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:

        kzalloc(a * b, gfp)

with:
        kcalloc(a * b, gfp)

as well as handling cases of:

        kzalloc(a * b * c, gfp)

with:

        kzalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kzalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kzalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kzalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kzalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kzalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kzalloc
+ kcalloc
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kzalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kzalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kzalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kzalloc(sizeof(THING) * C2, ...)
|
  kzalloc(sizeof(TYPE) * C2, ...)
|
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 16:19:22 -07:00
Linus Torvalds 2857676045 - Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
 - Introduce overflow test module (Rasmus, Kees)
 - Introduce saturating size helper functions (Matthew, Kees)
 - Treewide use of struct_size() for allocators (Kees)
 -----BEGIN PGP SIGNATURE-----
 Comment: Kees Cook <kees@outflux.net>
 
 iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAlsYJ1gWHGtlZXNjb29r
 QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJlCTEACwdEeriAd2VwxknnsstojGD/3g
 8TTFA19vSu4Gxa6WiDkjGoSmIlfhXTlZo1Nlmencv16ytSvIVDNLUIB3uDxUIv1J
 2+dyHML9JpXYHHR7zLXXnGFJL0wazqjbsD3NYQgXqmun7EVVYnOsAlBZ7h/Lwiej
 jzEJd8DaHT3TA586uD3uggiFvQU0yVyvkDCDONIytmQx+BdtGdg9TYCzkBJaXuDZ
 YIthyKDvxIw5nh/UaG3L+SKo73tUr371uAWgAfqoaGQQCWe+mxnWL4HkCKsjFzZL
 u9ouxxF/n6pij3E8n6rb0i2fCzlsTDdDF+aqV1rQ4I4hVXCFPpHUZgjDPvBWbj7A
 m6AfRHVNnOgI8HGKqBGOfViV+2kCHlYeQh3pPW33dWzy/4d/uq9NIHKxE63LH+S4
 bY3oO2ela8oxRyvEgXLjqmRYGW1LB/ZU7FS6Rkx2gRzo4k8Rv+8K/KzUHfFVRX61
 jEbiPLzko0xL9D53kcEn0c+BhofK5jgeSWxItdmfuKjLTW4jWhLRlU+bcUXb6kSS
 S3G6aF+L+foSUwoq63AS8QxCuabuhreJSB+BmcGUyjthCbK/0WjXYC6W/IJiRfBa
 3ZTxBC/2vP3uq/AGRNh5YZoxHL8mSxDfn62F+2cqlJTTKR/O+KyDb1cusyvk3H04
 KCDVLYPxwQQqK1Mqig==
 =/3L8
 -----END PGP SIGNATURE-----

Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux

Pull overflow updates from Kees Cook:
 "This adds the new overflow checking helpers and adds them to the
  2-factor argument allocators. And this adds the saturating size
  helpers and does a treewide replacement for the struct_size() usage.
  Additionally this adds the overflow testing modules to make sure
  everything works.

  I'm still working on the treewide replacements for allocators with
  "simple" multiplied arguments:

     *alloc(a * b, ...) -> *alloc_array(a, b, ...)

  and

     *zalloc(a * b, ...) -> *calloc(a, b, ...)

  as well as the more complex cases, but that's separable from this
  portion of the series. I expect to have the rest sent before -rc1
  closes; there are a lot of messy cases to clean up.

  Summary:

   - Introduce arithmetic overflow test helper functions (Rasmus)

   - Use overflow helpers in 2-factor allocators (Kees, Rasmus)

   - Introduce overflow test module (Rasmus, Kees)

   - Introduce saturating size helper functions (Matthew, Kees)

   - Treewide use of struct_size() for allocators (Kees)"

* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  treewide: Use struct_size() for devm_kmalloc() and friends
  treewide: Use struct_size() for vmalloc()-family
  treewide: Use struct_size() for kmalloc()-family
  device: Use overflow helpers for devm_kmalloc()
  mm: Use overflow helpers in kvmalloc()
  mm: Use overflow helpers in kmalloc_array*()
  test_overflow: Add memory allocation overflow tests
  overflow.h: Add allocation size calculation helpers
  test_overflow: Report test failures
  test_overflow: macrofy some more, do more tests for free
  lib: add runtime test of check_*_overflow functions
  compiler.h: enable builtin overflow checkers and add fallback code
2018-06-06 17:27:14 -07:00
Kees Cook 0ed2dd03b9 treewide: Use struct_size() for devm_kmalloc() and friends
Replaces open-coded struct size calculations with struct_size() for
devm_*, f2fs_*, and sock_* allocations. Automatically generated (and
manually adjusted) from the following Coccinelle script:

// Direct reference to struct field.
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@

- alloc(HANDLE, sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(HANDLE, struct_size(VAR, ELEMENT, COUNT), GFP)

// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@

- alloc(HANDLE, sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(HANDLE, struct_size(VAR, ELEMENT, COUNT), GFP)

// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "devm_kmalloc|devm_kzalloc|sock_kmalloc|f2fs_kmalloc|f2fs_kzalloc";
expression HANDLE;
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@

- alloc(HANDLE, sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(HANDLE, CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-06 11:15:43 -07:00
Lukas Wunner 32bee8f48f can: hi311x: Work around TX complete interrupt erratum
When sending packets as fast as possible using "cangen -g 0 -i -x", the
HI-3110 occasionally latches the interrupt pin high on completion of a
packet, but doesn't set the TXCPLT bit in the INTF register.  The INTF
register contains 0x00 as if no interrupt has occurred.  Even waiting
for a few milliseconds after the interrupt doesn't help.

Work around this apparent erratum by instead checking the TXMTY bit in
the STATF register ("TX FIFO empty").  We know that we've queued up a
packet for transmission if priv->tx_len is nonzero.  If the TX FIFO is
empty, transmission of that packet must have completed.

Note that this is congruent with our handling of received packets, which
likewise gleans from the STATF register whether a packet is waiting in
the RX FIFO, instead of looking at the INTF register.

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-05-10 18:25:30 +02:00
Lukas Wunner 5cec9425b4 can: hi311x: Acquire SPI lock on ->do_get_berr_counter
hi3110_get_berr_counter() may run concurrently to the rest of the driver
but neglects to acquire the lock protecting access to the SPI device.
As a result, it and the rest of the driver may clobber each other's tx
and rx buffers.

We became aware of this issue because transmission of packets with
"cangen -g 0 -i -x" frequently hung.  It turns out that agetty executes
->do_get_berr_counter every few seconds via the following call stack:

    CPU: 2 PID: 1605 Comm: agetty
    [<7f3f7500>] (hi3110_get_berr_counter [hi311x])
    [<7f130204>] (can_fill_info [can_dev])
    [<80693bc0>] (rtnl_fill_ifinfo)
    [<806949ec>] (rtnl_dump_ifinfo)
    [<806b4834>] (netlink_dump)
    [<806b4bc8>] (netlink_recvmsg)
    [<8065f180>] (sock_recvmsg)
    [<80660f90>] (___sys_recvmsg)
    [<80661e7c>] (__sys_recvmsg)
    [<80661ec0>] (SyS_recvmsg)
    [<80108b20>] (ret_fast_syscall+0x0/0x1c)

agetty listens to netlink messages in order to update the login prompt
when IP addresses change (if /etc/issue contains \4 or \6 escape codes):
https://git.kernel.org/pub/scm/utils/util-linux/util-linux.git/commit/?id=e36deb6424e8

It's a useful feature, though it seems questionable that it causes CAN
bit error statistics to be queried.

Be that as it may, if hi3110_get_berr_counter() is invoked while a frame
is sent by hi3110_hw_tx(), bogus SPI transfers like the following may
occur:

    => 12 00             (hi3110_get_berr_counter() wanted to transmit
                          EC 00 to query the transmit error counter,
                          but the first byte was overwritten by
                          hi3110_hw_tx_frame())

    => EA 00 3E 80 01 FB (hi3110_hw_tx_frame() wanted to transmit a
                          frame, but the first byte was overwritten by
                          hi3110_get_berr_counter() because it wanted
                          to query the receive error counter)

This sequence hangs the transmission because the driver believes it has
sent a frame and waits for the interrupt signaling completion, but in
reality the chip has never sent away the frame since the commands it
received were malformed.

Fix by acquiring the SPI lock in hi3110_get_berr_counter().

I've scrutinized the entire driver for further unlocked SPI accesses but
found no others.

Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Cc: Stef Walter <stefw@redhat.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-05-10 18:20:51 +02:00
Jimmy Assarsson 6ee00865ff can: kvaser_usb: Increase correct stats counter in kvaser_usb_rx_can_msg()
Increase rx_dropped, if alloc_can_skb() fails, not tx_dropped.

Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-05-08 10:41:38 +02:00
Uwe Kleine-König 0e030a373d can: flexcan: fix endianess detection
In commit 88462d2a78 ("can: flexcan: Remodel FlexCAN register r/w APIs
for big endian FlexCAN controllers.") the following logic was
implemented:

	if the dt property "big-endian" is given or
	   the device is compatible to "fsl,p1010-flexcan":
		use big-endian mode;
	else
		use little-endian mode;

This relies on commit d50f4630c2 ("arm: dts: Remove p1010-flexcan
compatible from imx series dts") which was applied a few commits later.
Without this commit (or an old device tree used for booting a new
kernel) the flexcan devices on i.MX25, i.MX28, i.MX35 and i.MX53 match
the 'the device is compatible to "fsl,p1010-flexcan"' test and so are
switched erroneously to big endian mode.

Instead of the check above put a quirk in devtype data and rely on
of_match_device yielding the most compatible match

Fixes: 88462d2a78 ("can: flexcan: Remodel FlexCAN register r/w APIs for big endian FlexCAN controllers.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Gavin Schenk <g.schenk@eckelmann.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-05-08 10:41:38 +02:00
Jakob Unterwurzacher 71c23a821c can: dev: increase bus-off message severity
bus-off is usually caused by hardware malfunction or configuration error
(baud rate mismatch) and causes a complete loss of communication.

Increase the "bus-off" message's severity from netdev_dbg() to
netdev_info() to make it visible to the user.

A can interface going into bus-off is similar in severity to ethernet's
"Link is Down" message, which is also printed at info level.

It is debatable whether the the "restarted" message should also be
changed to netdev_info() to make the interface state changes
comprehensible from the kernel log. I have chosen to keep the
"restarted" message at dbg for now as the "bus-off" message should be
enough for the user to notice and investigate the problem.

Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Cc: linux-can@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-05-08 10:41:38 +02:00
Linus Torvalds 5bb053bef8 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) Support offloading wireless authentication to userspace via
    NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.

 2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
    Setup and cleanup of namespaces now all run asynchronously and thus
    performance is significantly increased.

 3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
    Streiff.

 4) Support zerocopy on RDS sockets, from Sowmini Varadhan.

 5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
    Borkmann.

 6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
    Chevallier.

 7) Support grafting of child qdiscs in mlxsw driver, from Nogah
    Frankel.

 8) Add packet forwarding tests to selftests, from Ido Schimmel.

 9) Deal with sub-optimal GSO packets better in BBR congestion control,
    from Eric Dumazet.

10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.

11) Add path MTU tests to selftests, from Stefano Brivio.

12) Various bits of IPSEC offloading support for mlx5, from Aviad
    Yehezkel, Yossi Kuperman, and Saeed Mahameed.

13) Support RSS spreading on ntuple filters in SFC driver, from Edward
    Cree.

14) Lots of sockmap work from John Fastabend. Applications can use eBPF
    to filter sendmsg and sendpage operations.

15) In-kernel receive TLS support, from Dave Watson.

16) Add XDP support to ixgbevf, this is significant because it should
    allow optimized XDP usage in various cloud environments. From Tony
    Nguyen.

17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
    Venkataramanan et al.

18) IP fragmentation match offload support in nfp driver, from Pieter
    Jansen van Vuuren.

19) Support XDP redirect in i40e driver, from Björn Töpel.

20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
    tracepoints in their raw form, from Alexei Starovoitov.

21) Lots of striding RQ improvements to mlx5 driver with many
    performance improvements, from Tariq Toukan.

22) Use rhashtable for inet frag reassembly, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
  net: mvneta: improve suspend/resume
  net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
  ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
  net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
  net: bgmac: Correctly annotate register space
  route: check sysctl_fib_multipath_use_neigh earlier than hash
  fix typo in command value in drivers/net/phy/mdio-bitbang.
  sky2: Increase D3 delay to sky2 stops working after suspend
  net/mlx5e: Set EQE based as default TX interrupt moderation mode
  ibmvnic: Disable irqs before exiting reset from closed state
  net: sched: do not emit messages while holding spinlock
  vlan: also check phy_driver ts_info for vlan's real device
  Bluetooth: Mark expected switch fall-throughs
  Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
  Bluetooth: btrsi: remove unused including <linux/version.h>
  Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
  sh_eth: kill useless check in __sh_eth_get_regs()
  sh_eth: add sh_eth_cpu_data::no_xdfar flag
  ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
  ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
  ...
2018-04-03 14:04:18 -07:00
Linus Torvalds f5a8eb632b arch: remove obsolete architecture ports
This removes the entire architecture code for blackfin, cris, frv, m32r,
 metag, mn10300, score, and tile, including the associated device drivers.
 
 I have been working with the (former) maintainers for each one to ensure
 that my interpretation was right and the code is definitely unused in
 mainline kernels. Many had fond memories of working on the respective
 ports to start with and getting them included in upstream, but also saw
 no point in keeping the port alive without any users.
 
 In the end, it seems that while the eight architectures are extremely
 different, they all suffered the same fate: There was one company
 in charge of an SoC line, a CPU microarchitecture and a software
 ecosystem, which was more costly than licensing newer off-the-shelf
 CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
 that all the SoC product lines are still around, but have not used the
 custom CPU architectures for several years at this point. In contrast,
 CPU instruction sets that remain popular and have actively maintained
 kernel ports tend to all be used across multiple licensees.
 
 The removal came out of a discussion that is now documented at
 https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
 marking any ports as deprecated but remove them all at once after I made
 sure that they are all unused. Some architectures (notably tile, mn10300,
 and blackfin) are still being shipped in products with old kernels,
 but those products will never be updated to newer kernel releases.
 
 After this series, we still have a few architectures without mainline
 gcc support:
 
 - unicore32 and hexagon both have very outdated gcc releases, but the
   maintainers promised to work on providing something newer. At least
   in case of hexagon, this will only be llvm, not gcc.
 
 - openrisc, risc-v and nds32 are still in the process of finishing their
   support or getting it added to mainline gcc in the first place.
   They all have patched gcc-7.3 ports that work to some degree, but
   complete upstream support won't happen before gcc-8.1. Csky posted
   their first kernel patch set last week, their situation will be similar.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJawdL2AAoJEGCrR//JCVInuH0P/RJAZh1nTD+TR34ZhJq2TBoo
 PgygwDU7Z2+tQVU+EZ453Gywz9/NMRFk1RWAZqrLix4ZtyIMvC6A1qfT2yH1Y7Fb
 Qh6tccQeLe4ezq5u4S/46R/fQXu3Txr92yVwzJJUuPyU0arF9rv5MmI8e6p7L1en
 yb74kSEaCe+/eMlsEj1Cc1dgthDNXGKIURHkRsILoweysCpesjiTg4qDcL+yTibV
 FP2wjVbniKESMKS6qL71tiT5sexvLsLwMNcGiHPj94qCIQuI7DLhLdBVsL5Su6gI
 sbtgv0dsq4auRYAbQdMaH1hFvu6WptsuttIbOMnz2Yegi2z28H8uVXkbk2WVLbqG
 ZESUwutGh8MzOL2RJ4jyyQq5sfo++CRGlfKjr6ImZRv03dv0pe/W85062cK5cKNs
 cgDDJjGRorOXW7dyU6jG2gRqODOQBObIv3w5efdq5OgzOWlbI4EC+Y5u1Z0JF/76
 pSwtGXA6YhwC+9LLAlnVTHG+yOwuLmAICgoKcTbzTVDKA2YQZG/cYuQfI5S1wD8e
 X6urPx3Md2GCwLXQ9mzKBzKZUpu/Tuhx0NvwF4qVxy6x1PELjn68zuP7abDHr46r
 57/09ooVN+iXXnEGMtQVS/OPvYHSa2NgTSZz6Y86lCRbZmUOOlK31RDNlMvYNA+s
 3iIVHovno/JuJnTOE8LY
 =fQ8z
 -----END PGP SIGNATURE-----

Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic

Pul removal of obsolete architecture ports from Arnd Bergmann:
 "This removes the entire architecture code for blackfin, cris, frv,
  m32r, metag, mn10300, score, and tile, including the associated device
  drivers.

  I have been working with the (former) maintainers for each one to
  ensure that my interpretation was right and the code is definitely
  unused in mainline kernels. Many had fond memories of working on the
  respective ports to start with and getting them included in upstream,
  but also saw no point in keeping the port alive without any users.

  In the end, it seems that while the eight architectures are extremely
  different, they all suffered the same fate: There was one company in
  charge of an SoC line, a CPU microarchitecture and a software
  ecosystem, which was more costly than licensing newer off-the-shelf
  CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
  seems that all the SoC product lines are still around, but have not
  used the custom CPU architectures for several years at this point. In
  contrast, CPU instruction sets that remain popular and have actively
  maintained kernel ports tend to all be used across multiple licensees.

  [ See the new nds32 port merged in the previous commit for the next
    generation of "one company in charge of an SoC line, a CPU
    microarchitecture and a software ecosystem"   - Linus ]

  The removal came out of a discussion that is now documented at
  https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
  marking any ports as deprecated but remove them all at once after I
  made sure that they are all unused. Some architectures (notably tile,
  mn10300, and blackfin) are still being shipped in products with old
  kernels, but those products will never be updated to newer kernel
  releases.

  After this series, we still have a few architectures without mainline
  gcc support:

   - unicore32 and hexagon both have very outdated gcc releases, but the
     maintainers promised to work on providing something newer. At least
     in case of hexagon, this will only be llvm, not gcc.

   - openrisc, risc-v and nds32 are still in the process of finishing
     their support or getting it added to mainline gcc in the first
     place. They all have patched gcc-7.3 ports that work to some
     degree, but complete upstream support won't happen before gcc-8.1.
     Csky posted their first kernel patch set last week, their situation
     will be similar

  [ Palmer Dabbelt points out that RISC-V support is in mainline gcc
    since gcc-7, although gcc-7.3.0 is the recommended minimum  - Linus ]"

This really says it all:

 2498 files changed, 95 insertions(+), 467668 deletions(-)

* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
  MAINTAINERS: UNICORE32: Change email account
  staging: iio: remove iio-trig-bfin-timer driver
  tty: hvc: remove tile driver
  tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
  serial: remove tile uart driver
  serial: remove m32r_sio driver
  serial: remove blackfin drivers
  serial: remove cris/etrax uart drivers
  usb: Remove Blackfin references in USB support
  usb: isp1362: remove blackfin arch glue
  usb: musb: remove blackfin port
  usb: host: remove tilegx platform glue
  pwm: remove pwm-bfin driver
  i2c: remove bfin-twi driver
  spi: remove blackfin related host drivers
  watchdog: remove bfin_wdt driver
  can: remove bfin_can driver
  mmc: remove bfin_sdh driver
  input: misc: remove blackfin rotary driver
  input: keyboard: remove bf54x driver
  ...
2018-04-02 20:20:12 -07:00
Joe Perches d61e403856 drivers/net: Use octal not symbolic permissions
Prefer the direct use of octal for permissions.

Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.

Miscellanea:

o Whitespace neatening around these conversions.

Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-26 12:07:49 -04:00
Arnd Bergmann c7b2d3e52d can: remove bfin_can driver
The blackfin architecture is getting removed, so this one is now obsolete.

Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-26 15:57:02 +02:00
Andri Yngvason 9ffd750394 can: cc770: Fix use after free in cc770_tx_interrupt()
This fixes use after free introduced by the last cc770 patch.

Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Fixes: 746201235b ("can: cc770: Fix queue stall & dropped RTR reply")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-19 10:57:29 +01:00
Andri Yngvason 746201235b can: cc770: Fix queue stall & dropped RTR reply
While waiting for the TX object to send an RTR, an external message with a
matching id can overwrite the TX data. In this case we must call the rx
routine and then try transmitting the message that was overwritten again.

The queue was being stalled because the RX event did not generate an
interrupt to wake up the queue again and the TX event did not happen
because the TXRQST flag is reset by the chip when new data is received.

According to the CC770 datasheet the id of a message object should not be
changed while the MSGVAL bit is set. This has been fixed by resetting the
MSGVAL bit before modifying the object in the transmit function and setting
it after. It is not enough to set & reset CPUUPD.

It is important to keep the MSGVAL bit reset while the message object is
being modified. Otherwise, during RTR transmission, a frame with matching
id could trigger an rx-interrupt, which would cause a race condition
between the interrupt routine and the transmit function.

Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Tested-by: Richard Weinberger <richard@nod.at>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-14 13:01:22 +01:00
Andri Yngvason f4353daf49 can: cc770: Fix stalls on rt-linux, remove redundant IRQ ack
This has been reported to cause stalls on rt-linux.

Suggested-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-14 13:00:15 +01:00
Bich HEMON c9b3bce18d can: m_can: select pinctrl state in each suspend/resume function
Make sure to apply the correct pin state in suspend/resume callbacks.
Putting pins in sleep state saves power.

Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-12 10:38:20 +01:00
Stephane Grosjean ffd137f704 can: peak/pcie_fd: remove useless code when interface starts
When an interface starts, the echo_skb array is empty and the network
queue should be started only. This patch replaces useless code and locks
when the internal RX_BARRIER message is received from the IP core, telling
the driver that tx may start.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-12 09:55:12 +01:00
Stephane Grosjean e6048a00cf can: peak/pcie_fd: fix echo_skb is occupied! bug
This patch makes atomic the handling of the linux-can echo_skb array and
the network tx queue. This prevents from the "BUG! echo_skb is occupied!"
message to be printed by the linux-can core, in SMP environments.

Reported-by: Diana Burgess <diana@peloton-tech.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-12 09:55:12 +01:00
Marek Vasut 880dd464b4 can: ifi: Repair the error handling
The new version of the IFI CANFD core has significantly less complex
error state indication logic. In particular, the warning/error state
bits are no longer all over the place, but are all present in the
STATUS register. Moreover, there is a new IRQ register bit indicating
transition between error states (active/warning/passive/busoff).

This patch makes use of this bit to weed out the obscure selective
INTERRUPT register clearing, which was used to carry over the error
state indication into the poll function. While at it, this patch
fixes the handling of the ACTIVE state, since the hardware provides
indication of the core being in ACTIVE state and that in turn fixes
the state transition indication toward userspace. Finally, register
reads in the poll function are moved to the matching subfunctions
since those are also no longer needed in the poll function.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-12 09:55:12 +01:00
Marek Vasut 591d65d5b1 can: ifi: Check core revision upon probe
Older versions of the core are not compatible with the driver due
to various intrusive fixes of the core. Read out the VER register,
check the core revision bitfield and verify if the core in use is
new enough (rev 2.1 or newer) to work correctly with this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Markus Marb <markus@marb.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-12 09:55:11 +01:00
Wolfram Sang b7db978ac2 can: m_can: change comparison to bitshift when dealing with a mask
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-03-12 09:55:11 +01:00
Robert Schwebel 7d59773945 can: migrate documentation to restructured text
The kernel documentation is now restructured text. Convert the SocketCAN
documentation and include it in the toplevel kernel documentation.

This patch doesn't do any content change.

All references to can.txt in the code are converted to can.rst.

Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-26 10:46:44 +01:00
David S. Miller 8565d26bcb Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The BPF verifier conflict was some minor contextual issue.

The TUN conflict was less trivial.  Cong Wang fixed a memory leak of
tfile->tx_array in 'net'.  This is an skb_array.  But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-19 22:59:33 -05:00
Arnd Bergmann 5835919319 can: m_can: mark runtime-PM handlers as __maybe_unused
Building without CONFIG_PM results in a harmless warning:

drivers/net/can/m_can/m_can.c:1763:12: error: 'm_can_runtime_resume' defined but not used [-Werror=unused-function]
drivers/net/can/m_can/m_can.c:1752:12: error: 'm_can_runtime_suspend' defined but not used [-Werror=unused-function]

Marking the functions as __maybe_unused lets the compiler
silently drop them instead.

Fixes: cdf8259d65 ("can: m_can: Add PM Support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-19 10:41:15 +01:00
Stephane Grosjean d8a243af1a can: peak: fix potential bug in packet fragmentation
In some rare conditions when running one PEAK USB-FD interface over
a non high-speed USB controller, one useless USB fragment might be sent.
This patch fixes the way a USB command is fragmented when its length is
greater than 64 bytes and when the underlying USB controller is not a
high-speed one.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-16 15:33:15 +01:00
Franklin S Cooper Jr 31643dc8fc can: m_can: Add call to of_can_transceiver
Add call to new generic functions that provides support via a binding
to limit the arbitration rate and/or data rate imposed by the physical
transceiver connected to the MCAN peripheral.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-16 15:11:35 +01:00
Faiz Abbas cdf8259d65 can: m_can: Add PM Support
Add support for CONFIG_PM which is the new way to handle managing clocks.

Move the clock management to pm_runtime_resume() and pm_runtime_suspend()
callbacks for the driver.

CONFIG_PM is required by OMAP based devices to handle clock management.
Therefore, this allows future Texas Instruments SoCs that have the MCAN IP
to work with this driver.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-16 15:11:34 +01:00
Marc Kleine-Budde 63dffc1c69 can: m_can: get rid of function free_m_can_dev()
As the previous patch removed alloc_m_can_dev(), let's get rid of the
corresponding free_m_can_dev() and call free_candev() directly.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-16 15:11:34 +01:00
Faiz Abbas 5e520edd91 can: m_can: Move allocation of net device to probe
With the version no longer required to allocate the net device, it can
be moved to probe and the alloc_m_can_dev() function can be simplified.

Therefore, move the allocation of net device to probe and change
alloc_m_can_dev() to setup_m_can_dev().

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-16 15:11:33 +01:00
Faiz Abbas b25abca6aa can: m_can: Remove check for version when allocating m_can net device
Currently the m_can version is used to set the tx_fifo_count to 1 when
allocating the net device. However, this is redundant as a value of 1
for the tx_fifo_count needs to be provided in the bosch,mram-cfg
property of the device tree node anyway.

Therefore, remove check for version when allocating the net device.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-16 15:11:33 +01:00
Franklin S Cooper Jr e759c626d8 can: m_can: Support higher speed CAN-FD bitrates
During test transmitting using CAN-FD at high bitrates (> 2 Mbps)
would fail. Scoping the signals I noticed that only a single bit
was being transmitted and with a bit more investigation realized the
actual MCAN IP would go back to initialization mode automatically.

It appears this issue is due to the MCAN needing to use the Transmitter
Delay Compensation Mode with the correct value for the transmitter delay
compensation offset (tdco). What impacts the tdco value isn't 100% clear
but to calculate it you use an equation defined in the MCAN User's Guide.

The user guide mentions that this register needs to be set based on clock
values, secondary sample point and the data bitrate. One of the key
variables that can't automatically be determined is the secondary
sample point (ssp). This ssp is similar to the sp but is specific to this
transmitter delay compensation mode. The guidelines for configuring
ssp is rather vague but via some CAN test it appears for DRA76x that
putting the value same as data sampling point works.

The CAN-CIA's "Bit Time Requirements for CAN FD" paper presented at
the International CAN Conference 2013 indicates that this TDC mode is
only needed for data bit rates above 2.5 Mbps. Therefore, only enable
this mode when the data bit rate is above 2.5 Mbps.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-16 15:11:33 +01:00
Franklin S Cooper Jr 2290aefa2e can: dev: Add support for limiting configured bitrate
Various CAN or CAN-FD IP may be able to run at a faster rate than
what the transceiver the CAN node is connected to. This can lead to
unexpected errors. However, CAN transceivers typically have fixed
limitations and provide no means to discover these limitations at
runtime. Therefore, add support for a can-transceiver node that
can be reused by other CAN peripheral drivers to determine for both
CAN and CAN-FD what the max bitrate that can be used. If the user
tries to configure CAN to pass these maximum bitrates it will throw
an error.

Also add support for reading bitrate_max via the netlink interface.

Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[nsekhar@ti.com: fix build error with !CONFIG_OF]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-16 15:11:32 +01:00
David S. Miller 79d891c1bb linux-can-next-for-4.16-20180105
-----BEGIN PGP SIGNATURE-----
 
 iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlpPT5ATHG1rbEBwZW5n
 dXRyb25peC5kZQAKCRAe/sog7Dgc9tyZB/wNk7hfmWT7qMSq4nB1/l4DvlCVtQR+
 7t7jLltd2ld1bqFr62S1/NExWbgm9GXS25wHgLQQn8I0jwCyuFb8K+VIe/+t9vSu
 PXOihUlIXCqpJwI9FtvGb/jmIbHV1JbnGv1b/J1q34FzhThsXN3DPX5BI5+T+Hy4
 9hnHuYtcveyGlU08RsePyc6WfCzBJafR1YpJYSSsIxmtT6Db0SyRSZjY4MFzv9eA
 mV+wvSpvepiw7tDN9XhSdNQJR9HAh/AXkYRgU448BysqhR5tK5oq8QAjsJK2Usy7
 X1RY/M32fn1QdcwfWEWw5xB9ZblKMnxRzB3vmGLkyvIuPnP/JGQoq5sW
 =BrhI
 -----END PGP SIGNATURE-----

Merge tag 'linux-can-next-for-4.16-20180105' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2017-12-01,Re: pull-request: can-next

this is a pull request of 7 patches for net-next/master.

All patches are by me. Patch 6 is for the "can_raw" protocol and add
error checking to the bind() function. All other patches clean up the
coding style and remove unused parameters in various CAN drivers and
infrastructure.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-15 16:13:34 -05:00
David S. Miller a0ce093180 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2018-01-09 10:37:00 -05:00
Marc Kleine-Budde 2ef5e75706 can: slcan: slc_alloc(): remove unused parameter "dev_t line"
The first and only parameter of slc_alloc() is unused, so remove it.

Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-05 11:12:08 +01:00
Marc Kleine-Budde 8e36917d73 can: peak_usb: peak_usb_netif_rx(): remove unused parameter "u32 ts_high"
The 4th argument of peak_usb_netif_rx() "u32 ts_high" is never used, so remove it.

Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-05 11:12:08 +01:00
Marc Kleine-Budde aa68172235 can: mcp251x: mcp251x_setup(): remove unused parameter "struct mcp251x_priv *priv"
The 2nd parameter of mcp251x_setup() "struct mcp251x_priv *priv" is not
used, so remove it.

Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2018-01-05 11:12:08 +01:00