Previously this driver always forced the copper page to be selected,
however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
needs to be selected. Set the appropriate mode based on the hardware
mode_cfg strap selection.
Enable the appropriate interrupt bits to detect fiber-side link up
or down events.
Update config_aneg and read_status methods to use the appropriate
Clause 37 calls when fiber mode is in use.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.
Fixes: c329e5afb4 ("net: phy: at803x: select correct page on config init")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update comments to only use kdoc style comments, starting with '/**',
for kdoc.
Flagged by ./scripts/kernel-doc
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220126090803.5582-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/net/ethernet/netronome/nfp/flower/tunnel_conf.c:359:25: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum1_kvdl.c:229:24: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PCS selection to use mac_select_pcs, which allows the PCS
to perform any validation it needs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert dpaa2-mac to use the mac_select_pcs() interface rather than
using phylink_set_pcs(). The intention here is to unify the approach
for PCS and eventually to remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
net: axienet: modernise pcs implementation
These two patches modernise the Xilinx axienet PCS implementation to
use the phylink split PCS support.
The first patch adds split PCS support and makes use of the newly
introduced mac_select_pcs() function, which is the preferred way to
conditionally attach a PCS.
The second patch cleans up the use of mdiobus_write() since we now have
bus accessors for mdio devices.
There should be no functional change to the driver.
This series was previously sent CFT on the 16th December (message ID
Ybs1cdM3KUTsq4Vx@shell.armlinux.org.uk), and feedback addressed. CFT v2
sent 4th January (message ID YdQlI8gcVwg2sR+5@shell.armlinux.org.uk).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ebecb2644 ("net: mdio: Add helper functions for accessing
MDIO devices") added support for mdiodev accessor operations that
neatly wrap the mdiobus accessor operations. Since we are dealing with
a mdio device here, update the driver to use mdiodev_write().
Tested-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert axienet to use the phylink_pcs layer, resulting in it no longer
being a legacy driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Add RTC mode for PTP
This series adds Real Time Clock (RTC) mode for PTP timestamping. In
RTC mode, the 64-bit time value is programmed into the NIC's PTP
hardware clock (PHC). Prior to this, the PHC is running as a free
counter. For example, in multi-function environment, we need to run
PTP in RTC mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Multi-host environment, when the PHC is updated by one host,
an async message from firmware will be sent to other hosts.
Re-initialize the timecounter when the driver receives this
async message.
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adjusted time is set in the PHC in RTC mode. We also need to
update the snapshots ptp->current_time and ptp->old_time when the
time is adjusted.
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTC mode if it is supported by firmware. In RTC
mode, the PHC is set to the 64-bit clock. Because the legacy interface
is 48-bit, the driver still has to keep track of the upper 16 bits and
handle the rollover.
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Making the ptp free and timecounter initialization code into separate
functions so that later patches can use them.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes are PTP support for RTC, additional NVM error codes,
backing store v2 firmware APIs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
net: stmmac/xpcs: modernise PCS support
This series updates xpcs and stmmac for the recent changes to phylink
to better support split PCS and to get rid of private MAC validation
functions.
This series is slightly more involved than other conversions as stmmac
has already had optional proper split PCS support.
The first six patches of this series were originally posted on 16th
December for CFT, and Wong Vee Khee reported his Intel Elkhart Lake
setup was fine the first six these. However, no tested-by was given.
The patches:
1) Provide a function to query the xpcs for the interface modes that
are supported.
2) Populates the MAC capabilities and switches stmmac_validate() to use
phylink_get_linkmodes(). We do not use phylink_generic_validate() yet
as (a) we do not always have the supported interfaces populated, and
(b) the existing code does not restrict based on interface. There
should be no functional effect from this patch.
3) Populates phylink's supported interfaces from the xpcs when the xpcs
is configured by firmware and also the firmware configured interface
mode. Note: this will restrict stmmac to only supporting these
interfaces modes - stmmac maintainers need to verify that this
behaviour is acceptable.
4) stmmac_validate() tail-calls xpcs_validate(), but we don't need it to
now that PCS have their own validation method. Convert stmmac and
xpcs to use this method instead.
5) xpcs sets the poll field of phylink_pcs to true, meaning xpcs
requires its status to be polled. There is no need to also set the
phylink_config.pcs_poll. Remove this.
6) Switch to phylink_generic_validate(). This is probably the most
contravertial change in this patch set as this will cause the MAC to
restrict link modes based on the interface mode. From an inspection
of the xpcs driver, this should be safe, as XPCS only further
restricts the link modes to a subset of these (whether that is
correct or not is not an issue I am addressing here.) For
implementations that do not use xpcs, this is a more open question
and needs feedback from stmmac maintainers.
7) Convert to use mac_select_pcs() rather than phylink_set_pcs() to set
the PCS - the intention is to eventually remove phylink_set_pcs()
once there are no more users of this.
v2: fix signoff and temporary warning in patch 4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert stmmac to use the mac_select_pcs() interface rather than using
phylink_set_pcs(). The intention here is to unify the approach for PCS
and eventually to remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert stmmac to use phylink_generic_validate() now that we have the
MAC capabilities and supported interfaces filled in, and we have the
PCS validation handled via the PCS operations.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink will use PCS polling whenever the PCS's poll member is set, so
setting phylink_config.pcs_poll as well is redundant.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac explicitly calls the xpcs driver to validate the ethtool
linkmodes. This is no longer necessary as phylink now supports
validation through a PCS method. Convert both drivers to use this
new mechanism.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill in phylink's supported_interfaces bitmap with the PHY interface
modes which can be used to talk to the PHY.
We indicate that the PHY interface mode passed in platform data is
always supported, as this is the initial mode passed into phylink.
When there is no PCS specified, we assume that this is the only mode
that is supported - indeed, the driver appears not to support dynamic
switching of interface types at present.
When a xpcs is present, it defines the PHY interface modes that the
stmmac driver can support. Request the supported interfaces from the
xpcs driver, and pass them to phylink.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the MAC speed, duplex and pause capabilities to the phylink_config
structure, and switch stmmac_validate() to use phylink_get_linkmodes()
to generate the mask of supported ethtool link modes.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to the xpcs driver to retrieve the supported PHY
interface modes, which can be used by drivers to fill in phylink's
supported_interfaces mask.
We validate the interface bit index to ensure that it fits within the
bitmap as xpcs lists PHY_INTERFACE_MODE_MAX in an entry.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Add RJ45 ports support
We are in the process of qualifying a new system that has RJ45 ports as
opposed to the transceiver modules (e.g., SFP, QSFP) present on all
existing systems.
This patchset adds support for these ports in mlxsw by adding a couple of
missing BaseT link modes and rejecting ethtool operations that are
specific to transceiver modules.
Patchset overview:
Patches #1-#3 are cleanups and preparations.
Patch #4 adds support for two new link modes.
Patches #5-#6 query and cache the port module's type (e.g., QSFP, RJ45)
during initialization.
Patches #7-#9 forbid ethtool operations that are invalid on RJ45 ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Transceiver module reset through 'rst' field in PMAOS register is not
supported on RJ45 ports, so module reset should be rejected.
Therefore, before trying to access this field, validate the port module
type that was queried during initialization and return an error to user
space in case the port module type is RJ45 (twisted pair).
Output example:
# ethtool --reset swp11 phy
ETHTOOL_RESET 0x40
Cannot issue ETHTOOL_RESET: Invalid argument
$ dmesg
mlxsw_spectrum 0000:03:00.0 swp11: Reset module is not supported on port module type
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PMMP (Port Module Memory Map Properties) and MCION (Management Cable IO
and Notifications) registers are not supported on RJ45 ports, so setting
and getting power mode should be rejected.
Therefore, before trying to access those registers, validate the port
module type that was queried during initialization and return an error
to user space in case the port module type is RJ45 (twisted pair).
Set output example:
# ethtool --set-module swp1 power-mode-policy auto
netlink error: mlxsw_core: Power mode is not supported on port module type
netlink error: Invalid argument
Get output example:
$ ethtool --show-module swp11
netlink error: mlxsw_core: Power mode is not supported on port module type
netlink error: Invalid argument
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCIA (Management Cable Info Access) register is not supported on RJ45
ports, so getting module EEPROM should be rejected.
Therefore, before trying to access this register, validate the port
module type that was queried during initialization and return an error
to user space in case the port module type is RJ45 (twisted pair).
Examples for output when trying to get EEPROM module:
Using netlink:
# ethtool -m swp1
netlink error: mlxsw_core: EEPROM is not equipped on port module type
netlink error: Invalid argument
Using IOCTL:
# ethtool -m swp1
Cannot get module EEPROM information: Invalid argument
$ dmesg
mlxsw_spectrum 0000:03:00.0 swp1: EEPROM is not equipped on port module type
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query and store port module's type during initialization so that it
could be later used to determine if certain configurations are allowed
based on the type.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Port Module Type Mapping (PMTP) register. It will be used by
subsequent patches to query port module types and forbid certain
configurations based on the port module's type.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a process for supporting a new system with RJ45 connectors,
100BaseT and 1000BaseT link modes need to be supported.
Add support for these two link modes by adding the two corresponding
bits in PTYS (Port Type and Speed) register.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patches will forbid querying the port module's EEPROM info when
its type is RJ45 as in this case no transceiver module can ever be
connected to the port.
Add netdev argument to mlxsw_env_get_module_info() so it could be used
to print an error to the kernel log via netdev_err().
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of modules can be resolved from the first argument, so do not
pass it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_gso_max_size is set based on the dst dev. Both users of it
adjust the value by the same offset - (MAX_TCP_HEADER + 1). Rather
than compute the same adjusted value on each call do the adjustment
once when set.
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220125024511.27480-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Variable new_csr6 is being initialized with a value that is never
read, it is being re-assigned later on. The assignment is redundant
and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220123183440.112495-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPv6 GRO considers packets to belong to different flows when their
hop_limit is different. This seems counter-intuitive, the flow is
the same. hop_limit may vary because of various bugs or hacks but
that doesn't mean it's okay for GRO to reorder packets.
Practical impact of this problem on overall TCP performance
is unclear, but TCP itself detects this reordering and bumps
TCPSACKReorder resulting in user complaints.
Eric warns that there may be performance regressions in setups
which do packet spraying across links with similar RTT but different
hop count. To be safe let's target -next and not treat this
as a fix. If the packet spraying is using flow label there should
be no difference in behavior as flow label is checked first.
Note that the code plays an easy to miss trick by upcasting next_hdr
to a u16 pointer and compares next_hdr and hop_limit in one go.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/net/ethernet/microsoft/mana/gdma_main.c:677:24: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is based on series [0] that extended the PM core. Now the compiler
can see the PM callbacks also on systems not defining CONFIG_PM.
The optimizer will remove the functions then in this case.
[0] https://lore.kernel.org/netdev/20211207002102.26414-1-paul@crapouillou.net/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Waldekranz says:
====================
net: dsa: Avoid cross-chip syncing of VLAN filtering
This bug has been latent in the source for quite some time, I suspect
due to the homogeneity of both typical configurations and hardware.
On singlechip systems, this would never be triggered. The only reason
I saw it on my multichip system was because not all chips had the same
number of ports, which means that the misdemeanor alien call turned
into a felony array-out-of-bounds access.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to VLAN filtering are not applicable to cross-chip
notifications.
On a system like this:
.-----. .-----. .-----.
| sw1 +---+ sw2 +---+ sw3 |
'-1-2-' '-1-2-' '-1-2-'
Before this change, upon sw1p1 leaving a bridge, a call to
dsa_port_vlan_filtering would also be made to sw2p1 and sw3p1.
In this scenario:
.---------. .-----. .-----.
| sw1 +---+ sw2 +---+ sw3 |
'-1-2-3-4-' '-1-2-' '-1-2-'
When sw1p4 would leave a bridge, dsa_port_vlan_filtering would be
called for sw2 and sw3 with a non-existing port - leading to array
out-of-bounds accesses and crashes on mv88e6xxx.
Fixes: d371b7c92d ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of dsa_switch_bridge_leave was, in fact, dealing with the syncing
of VLAN filtering for switches on which that is a global
setting. Separate the two phases to prepare for the cross-chip related
bugfix in the following commit.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
netns: speedup netns dismantles
netns are dismantled by a single thread, from cleanup_net()
On hosts with many TCP sockets, and/or many cpus, this thread
is spending too many cpu cycles, and can not keep up with some
workloads.
- Removing 3*num_possible_cpus() sockets per netns, for icmp and tcp protocols.
- Iterating over all TCP sockets to remove stale timewait sockets.
This patch series removes ~50% of cleanup_net() cpu costs on
hosts with 256 cpus. It also reduces per netns memory footprint.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP ipv4 uses per-cpu/per-netns ctl sockets in order to send
RST and some ACK packets (on behalf of TIMEWAIT sockets).
This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.
tcp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer
in order to be able to use IPv4 output functions.
Note that I attempted a related change in the past, that had
to be hot-fixed in commit bdbbb8527b ("ipv4: tcp: get rid of ugly unicast_sock")
This patch could very well surface old bugs, on layers not
taking care of sk->sk_kern_sock properly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in linux-2.6.25 (commit 98c6d1b261 "[NETNS]: Make icmpv6_sk per namespace.",
we added private per-cpu/per-netns ipv6 icmp sockets.
This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.
icmp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer.
icmpv6_xmit_lock() already makes sure to lock the chosen per-cpu
socket.
This patch has a considerable impact on the number of netns
that the worker thread in cleanup_net() can dismantle per second,
because ip6mr_sk_done() is no longer called, meaning we no longer
acquire the rtnl mutex, competing with other threads adding new netns.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in linux-2.6.25 (commit 4a6ad7a141 "[NETNS]: Make icmp_sk per namespace."),
we added private per-cpu/per-netns ipv4 icmp sockets.
This adds memory and cpu costs, which do not seem needed.
Now typical servers have 256 or more cores, this adds considerable
tax to netns users.
icmp sockets are used from BH context, are not receiving packets,
and do not store any persistent state but the 'struct net' pointer.
icmp_xmit_lock() already makes sure to lock the chosen per-cpu
socket.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior patches in the series made sure tw_timer_handler()
can be fired after netns has been dismantled/freed.
We no longer have to scan a potentially big TCP ehash
table at netns dismantle.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon get rid of inet_twsk_purge().
This means that tw_timer_handler() might fire after
a netns has been dismantled/freed.
Instead of adding a function (and data structure) to find a netns
from tw->tw_net_cookie, just update the SNMP counters
a bit earlier, when the netns is known to be alive.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Hancock
Eric Dumazet
Simon Horman
Corentin Labbe
Gustavo A. R. Silva
Russell King (Oracle)
David S. Miller
Pavan Chebbi
Michael Chan
Danielle Ratson
Ido Schimmel
David Ahern
Colin Ian King
Jakub Kicinski
Heiner Kallweit
Tobias Waldekranz