This patch adds symbol rate setting to the driver.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Print notice on driver load: "SDR API is still slightly
experimental and functionality changes may follow". It is just
remind possible used SDR API is very new and surprises may occur.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move it out of staging into media like all the other SDR drivers
too. There is no good reasons to keep these SDR drivers in staging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-compliance is now happy with frequency ranges where both lower
and upper limit is same.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move emulated format behind module parameter as those are not
supported. Format conversions will be on library eventually.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Mirics MSi001 and MSi2500 drivers uses SPI bus. Due to that we need
auto-select it too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add software defined radio device support for media Kconfig.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver moved out of staging. Update MAINTAINERS
accordingly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/staging/media/airspy/airspy.c: In function 'airspy_stop_streaming':
drivers/staging/media/airspy/airspy.c:569:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_SDR_FMT_CS14LE is complex signed 14-bit sample format, used
for software defined radio devices.
[m.chehab@samsung.com: remove V4L2_FL_USE_FH_PRIO setting to avoid
compilation breakage, as this flag doesn't exist anymore]
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_SDR_FMT_CS8 is complex signed 8-bit sample format, used for
software defined radio devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
AirSpy SDR driver.
Thanks to Youssef Touil and Benjamin Vernoux for support, help and
hardware!
http://airspy.com/
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Document V4L2_SDR_FMT_RU12LE format. It is real unsigned 12-bit
little endian sample inside 16-bit space. Used by software defined
radio devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement unlocked variants of v4l2_ctrl_s_ctrl() and
v4l2_ctrl_s_ctrl_int64(). As drivers need to set controls as they access
driver internal state elsewhere than in the control framework unlocked
variants of these functions become handy.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Drivers may use the v4l2_ctrl_modify_range() internally as part of other
operations that need to be both serialised using a driver's lock which can
also be used to serialise access to the control handler. Provide an unlocked
version of the function, __v4l2_ctrl_modify_range() which then may be used
by drivers for the purpose.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_ctrl_{,un}lock will be needed elsewhere. Define them before the
functions that perform operations on controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fall-out from the recent struct v4l2_framebuffer change.
drivers/media/common/saa7146/saa7146_fops.c: In function ‘saa7146_vv_init’:
drivers/media/common/saa7146/saa7146_fops.c:536:6: warning: assignment from incompatible pointer type [enabled by default]
fmt = &vv->ov_fb.fmt;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
[linux-3.16-rc5/drivers/staging/media/davinci_vpfe/dm365_ipipeif.c:210]:
(style) Checking if unsigned variable 'val' is less than zero.
val = get_oneshot_mode(ipipeif->input);
if (val < 0) {
pr_err("ipipeif: links setup required");
return -EINVAL;
}
but
static int get_oneshot_mode(enum ipipeif_input_entity input)
Introduced temporary variable for negativity check.
"val" is afterwards used in a lot of bitwise operations, so changing its type
to signed is not safe, according to CERT C Secure Coding Standards chapter
INT13-C: "Use bitwise operators only on unsigned operands"
https://www.securecoding.cert.org/confluence/display/seccode/INT13-C.+Use+bitwise+operators+only+on+unsigned+operands
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80521
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver moved over to v4l2_async_unregister_subdev()
but still retained a call to v4l2_unregister_subdev(). Remove.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CPB size is limited by the hardware. Add this limit to the s_fmt.
Signed-off-by: panpan liu <panpan1.liu@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
OVL and BTP IRAM buffers are never used, setup the bits for
for DBK/BIT/IP usage depending on CODA version in one place.
Also, use a simple allocator function and group IRAM addresses
and size in a coda_aux_buf structure.
This is done in preparation for CODA960 support.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If bitrate is not set, the encoder is running in VBR mode, with the
I- and P-frame quantization parameters configured from userspace.
For the quantization parameters, 0 is a valid value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently the rotator unit is used to copy decoded frames out into buffers
provided by videobuf2. Since the CODA reports the I/P/B frame type of the
last decoded frame, and this frame will be copied out in a later device_run,
depending on display order, we have to store the frame type until such time.
This patch also adds the B-frame type.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fc906b6d "Remove special clock usage in driver" removed
initialization of MFC special clock, arguing that there's
no need to do it explicitly, since it's one of MFC gate clock's
dependencies and gets enabled along with it. However, there's
no promise of keeping this hierarchy across Exynos SoC
releases, therefore this approach fails to provide a stable,
portable solution.
Out of all MFC versions, only v6 doesn't use special clock at all.
For other versions log a message only in case clk_get fails,
as not all the devices with the same MFC version require
initializing the clock explicitly.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the s5p_mfc_alloc_firmware() function there are some mistakes
where the code checks whether the DMA memory is properly allocated or
not.
First of all dma_alloc_coherent() returns NULL in case of error.
The code also checked two times fw_virt_addr, ignoring
the bank2_virt pointer.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ZR050_MO_COMP define is cut and pasted twice so we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the null test on dvb. dvb is initialized at the
beginning of the function to &port->dvb. Since port is dereferenced
prior to the null test, port must be a valid pointer, and
&port->dvb cannot be null.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the following warnings reported in radio-bcm2048.c:
WARNING: else is not generally useful after a break or return
374: FILE: radio-bcm2048.c:374:
+ return 0;
+ } else {
WARNING: else is not generally useful after a break or return
728: FILE: radio-bcm2048.c:728:
+ return BCM2048_DE_EMPHASIS_75us;
+ else
WARNING: unchecked sscanf return value
1974: FILE: radio-bcm2048.c:1974:
+ sscanf(buf, mask, &value); \
WARNING: Missing a blank line after declarations
2245: FILE: radio-bcm2048.c:2245:
+ unsigned char tmpbuf[3];
+ tmpbuf[i] = bdev->rds_info.radio_text[bdev->rd_index+i+2];
WARNING: Possible unnecessary 'out of memory' message
2601: FILE: radio-bcm2048.c:2601:
+ if (!bdev) {
+ dev_dbg(&client->dev, "Failed to alloc video device.\n");
The following error was left since it seems to be a false positive:
ERROR: Macros with complex values should be enclosed in parenthesis
+#define DEFINE_SYSFS_PROPERTY(prop, signal, size, mask, check) \
+property_write(prop, signal size, mask, check) \
+property_read(prop, size, mask)
Signed-off-by: Luke Hart <luke.hart@birchleys.eu>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The issue was discovered by static analysis. It turns out that code is
somewhat insane, being
if (x) {...} else { if (x) {...} }
Edited it to do the only reasonable thing, which is to log the
information about the failed call. The most descriptive logging commands
set is taken from original code.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79801
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- this patch removes IRQF_DISABLED macro, as this is
deprecated/noop.
Signed-off-by: Anil Belur <askb23@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Previously, it was needed to reopen device to update GOP size and
quantization parameter. Now we update device registers with new values
immediately.
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
solo6*10 boards have configurable quantization parameter which takes
values from 0 to 31, inclusively.
This change enables setting it with ioctl VIDIOC_S_CTRL with id
V4L2_CID_MPEG_VIDEO_H264_MIN_QP.
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The total number of bits is 16 (12+4). Fix it.
Signed-off-by: Andreas Weber <andy.weber.aw@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The colorspace for HDTV is REC709, not SMPTE240M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Hauppauge model 71100: WinTV-ImpactVCB-e
(PCIe, Retail, half height)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Otherwise you cannot get the current clip and bitmap information from
an overlay.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the vidioc_cropcap op is implemented by the driver then the v4l2
core will call that directly.
If g_selection is available, then the core cropcap implementation
uses g_selection to fill in the bounds and defrect and it sets the
pixelaspect to 1x1.
But if both are available, then I would like to use g_selection to
fill in defrect and bounds before calling cropcap. That way the
driver's cropcap implementation doesn't have to set defrect or
bounds.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Be sure that the reserved fields are cleared.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The edid field is the last field of the struct, so there is nothing to clear.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Luis Alves
Antti Palosaari
Mauro Carvalho Chehab
Sakari Ailus
Hans Verkuil
Andrey Utkin
Ian Molton
panpan liu
Philipp Zabel
Jacek Anaszewski
Maurizio Lombardi
Dan Carpenter
Himangi Saraogi
Luke Hart
Anil Belur
Andrey Utkin
Andreas Weber
Geert Uytterhoeven
Hans Verkuil