Merge in latest upstream (and the latest perf development tree),
to prepare for tooling changes, and also to pick up v3.4 MM
changes that the uprobes code needs to take care of.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[This patch depends on luto@mit.edu's no_new_privs patch:
https://lkml.org/lkml/2012/1/30/264
The whole series including Andrew's patches can be found here:
https://github.com/redpig/linux/tree/seccomp
Complete diff here:
https://github.com/redpig/linux/compare/1dc65fed...seccomp
]
This patch adds support for seccomp mode 2. Mode 2 introduces the
ability for unprivileged processes to install system call filtering
policy expressed in terms of a Berkeley Packet Filter (BPF) program.
This program will be evaluated in the kernel for each system call
the task makes and computes a result based on data in the format
of struct seccomp_data.
A filter program may be installed by calling:
struct sock_fprog fprog = { ... };
...
prctl(PR_SET_SECCOMP, SECCOMP_MODE_FILTER, &fprog);
The return value of the filter program determines if the system call is
allowed to proceed or denied. If the first filter program installed
allows prctl(2) calls, then the above call may be made repeatedly
by a task to further reduce its access to the kernel. All attached
programs must be evaluated before a system call will be allowed to
proceed.
Filter programs will be inherited across fork/clone and execve.
However, if the task attaching the filter is unprivileged
(!CAP_SYS_ADMIN) the no_new_privs bit will be set on the task. This
ensures that unprivileged tasks cannot attach filters that affect
privileged tasks (e.g., setuid binary).
There are a number of benefits to this approach. A few of which are
as follows:
- BPF has been exposed to userland for a long time
- BPF optimization (and JIT'ing) are well understood
- Userland already knows its ABI: system call numbers and desired
arguments
- No time-of-check-time-of-use vulnerable data accesses are possible.
- system call arguments are loaded on access only to minimize copying
required for system call policy decisions.
Mode 2 support is restricted to architectures that enable
HAVE_ARCH_SECCOMP_FILTER. In this patch, the primary dependency is on
syscall_get_arguments(). The full desired scope of this feature will
add a few minor additional requirements expressed later in this series.
Based on discussion, SECCOMP_RET_ERRNO and SECCOMP_RET_TRACE seem to be
the desired additional functionality.
No architectures are enabled in this patch.
Signed-off-by: Will Drewry <wad@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Reviewed-by: Indan Zupancic <indan@nul.nu>
Acked-by: Eric Paris <eparis@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
v18: - rebase to v3.4-rc2
- s/chk/check/ (akpm@linux-foundation.org,jmorris@namei.org)
- allocate with GFP_KERNEL|__GFP_NOWARN (indan@nul.nu)
- add a comment for get_u32 regarding endianness (akpm@)
- fix other typos, style mistakes (akpm@)
- added acked-by
v17: - properly guard seccomp filter needed headers (leann@ubuntu.com)
- tighten return mask to 0x7fff0000
v16: - no change
v15: - add a 4 instr penalty when counting a path to account for seccomp_filter
size (indan@nul.nu)
- drop the max insns to 256KB (indan@nul.nu)
- return ENOMEM if the max insns limit has been hit (indan@nul.nu)
- move IP checks after args (indan@nul.nu)
- drop !user_filter check (indan@nul.nu)
- only allow explicit bpf codes (indan@nul.nu)
- exit_code -> exit_sig
v14: - put/get_seccomp_filter takes struct task_struct
(indan@nul.nu,keescook@chromium.org)
- adds seccomp_chk_filter and drops general bpf_run/chk_filter user
- add seccomp_bpf_load for use by net/core/filter.c
- lower max per-process/per-hierarchy: 1MB
- moved nnp/capability check prior to allocation
(all of the above: indan@nul.nu)
v13: - rebase on to 88ebdda615
v12: - added a maximum instruction count per path (indan@nul.nu,oleg@redhat.com)
- removed copy_seccomp (keescook@chromium.org,indan@nul.nu)
- reworded the prctl_set_seccomp comment (indan@nul.nu)
v11: - reorder struct seccomp_data to allow future args expansion (hpa@zytor.com)
- style clean up, @compat dropped, compat_sock_fprog32 (indan@nul.nu)
- do_exit(SIGSYS) (keescook@chromium.org, luto@mit.edu)
- pare down Kconfig doc reference.
- extra comment clean up
v10: - seccomp_data has changed again to be more aesthetically pleasing
(hpa@zytor.com)
- calling convention is noted in a new u32 field using syscall_get_arch.
This allows for cross-calling convention tasks to use seccomp filters.
(hpa@zytor.com)
- lots of clean up (thanks, Indan!)
v9: - n/a
v8: - use bpf_chk_filter, bpf_run_filter. update load_fns
- Lots of fixes courtesy of indan@nul.nu:
-- fix up load behavior, compat fixups, and merge alloc code,
-- renamed pc and dropped __packed, use bool compat.
-- Added a hidden CONFIG_SECCOMP_FILTER to synthesize non-arch
dependencies
v7: (massive overhaul thanks to Indan, others)
- added CONFIG_HAVE_ARCH_SECCOMP_FILTER
- merged into seccomp.c
- minimal seccomp_filter.h
- no config option (part of seccomp)
- no new prctl
- doesn't break seccomp on systems without asm/syscall.h
(works but arg access always fails)
- dropped seccomp_init_task, extra free functions, ...
- dropped the no-asm/syscall.h code paths
- merges with network sk_run_filter and sk_chk_filter
v6: - fix memory leak on attach compat check failure
- require no_new_privs || CAP_SYS_ADMIN prior to filter
installation. (luto@mit.edu)
- s/seccomp_struct_/seccomp_/ for macros/functions (amwang@redhat.com)
- cleaned up Kconfig (amwang@redhat.com)
- on block, note if the call was compat (so the # means something)
v5: - uses syscall_get_arguments
(indan@nul.nu,oleg@redhat.com, mcgrathr@chromium.org)
- uses union-based arg storage with hi/lo struct to
handle endianness. Compromises between the two alternate
proposals to minimize extra arg shuffling and account for
endianness assuming userspace uses offsetof().
(mcgrathr@chromium.org, indan@nul.nu)
- update Kconfig description
- add include/seccomp_filter.h and add its installation
- (naive) on-demand syscall argument loading
- drop seccomp_t (eparis@redhat.com)
v4: - adjusted prctl to make room for PR_[SG]ET_NO_NEW_PRIVS
- now uses current->no_new_privs
(luto@mit.edu,torvalds@linux-foundation.com)
- assign names to seccomp modes (rdunlap@xenotime.net)
- fix style issues (rdunlap@xenotime.net)
- reworded Kconfig entry (rdunlap@xenotime.net)
v3: - macros to inline (oleg@redhat.com)
- init_task behavior fixed (oleg@redhat.com)
- drop creator entry and extra NULL check (oleg@redhat.com)
- alloc returns -EINVAL on bad sizing (serge.hallyn@canonical.com)
- adds tentative use of "always_unprivileged" as per
torvalds@linux-foundation.org and luto@mit.edu
v2: - (patch 2 only)
Signed-off-by: James Morris <james.l.morris@oracle.com>
cgroup/for-3.5 contains the following changes which blk-cgroup needs
to proceed with the on-going cleanup.
* Dynamic addition and removal of cftypes to make config/stat file
handling modular for policies.
* cgroup removal update to not wait for css references to drain to fix
blkcg removal hang caused by cfq caching cfqgs.
Pull in cgroup/for-3.5 into block/for-3.5/core. This causes the
following conflicts in block/blk-cgroup.c.
* 761b3ef50e "cgroup: remove cgroup_subsys argument from callbacks"
conflicts with blkiocg_pre_destroy() addition and blkiocg_attach()
removal. Resolved by removing @subsys from all subsys methods.
* 676f7c8f84 "cgroup: relocate cftype and cgroup_subsys definitions in
controllers" conflicts with ->pre_destroy() and ->attach() updates
and removal of modular config. Resolved by dropping forward
declarations of the methods and applying updates to the relocated
blkio_subsys.
* 4baf6e3325 "cgroup: convert all non-memcg controllers to the new
cftype interface" builds upon the previous item. Resolved by adding
->base_cftypes to the relocated blkio_subsys.
Signed-off-by: Tejun Heo <tj@kernel.org>
Maintain a per-mm counter: number of uprobes that are inserted
on this process address space.
This counter can be used at probe hit time to determine if we
need a lookup in the uprobes rbtree. Everytime a probe gets
inserted successfully, the probe count is incremented and
everytime a probe gets removed, the probe count is decremented.
The new uprobe_munmap hook ensures the count is correct on a
unmap or remap of a region. We expect that once a
uprobe_munmap() is called, the vma goes away. So
uprobe_unregister() finding a probe to unregister would either
mean unmap event hasnt occurred yet or a mmap event on the same
executable file occured after a unmap event.
Additionally, uprobe_mmap hook now also gets called:
a. on every executable vma that is COWed at fork.
b. a vma of interest is newly mapped; breakpoint insertion also
happens at the required address.
On process creation, make sure the probes count in the child is
set correctly.
Special cases that are taken care include:
a. mremap
b. VM_DONTCOPY vmas on fork()
c. insertion/removal races in the parent during fork().
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Anton Arapov <anton@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120330182646.10018.85805.sendpatchset@srdronam.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Uprobes executes the original instruction at a probed location
out of line. For this, we allocate a page (per mm) upon the
first uprobe hit, in the process user address space, divide it
into slots that are used to store the actual instructions to be
singlestepped. These slots are known as xol (execution out of
line) slots.
Care is taken to ensure that the allocation is in an unmapped
area as close to the top of the user address space as possible,
with appropriate permission settings to keep selinux like
frameworks happy.
Upon a uprobe hit, a free slot is acquired, and is released
after the singlestep completes.
Lots of improvements courtesy suggestions/inputs from Peter and
Oleg.
[ Folded a fix for build issue on powerpc fixed and reported by
Stephen Rothwell. ]
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Anton Arapov <anton@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120330182631.10018.48175.sendpatchset@srdronam.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Userspace service managers/supervisors need to track their started
services. Many services daemonize by double-forking and get implicitly
re-parented to PID 1. The service manager will no longer be able to
receive the SIGCHLD signals for them, and is no longer in charge of
reaping the children with wait(). All information about the children is
lost at the moment PID 1 cleans up the re-parented processes.
With this prctl, a service manager process can mark itself as a sort of
'sub-init', able to stay as the parent for all orphaned processes
created by the started services. All SIGCHLD signals will be delivered
to the service manager.
Receiving SIGCHLD and doing wait() is in cases of a service-manager much
preferred over any possible asynchronous notification about specific
PIDs, because the service manager has full access to the child process
data in /proc and the PID can not be re-used until the wait(), the
service-manager itself is in charge of, has happened.
As a side effect, the relevant parent PID information does not get lost
by a double-fork, which results in a more elaborate process tree and
'ps' output:
before:
# ps afx
253 ? Ss 0:00 /bin/dbus-daemon --system --nofork
294 ? Sl 0:00 /usr/libexec/polkit-1/polkitd
328 ? S 0:00 /usr/sbin/modem-manager
608 ? Sl 0:00 /usr/libexec/colord
658 ? Sl 0:00 /usr/libexec/upowerd
819 ? Sl 0:00 /usr/libexec/imsettings-daemon
916 ? Sl 0:00 /usr/libexec/udisks-daemon
917 ? S 0:00 \_ udisks-daemon: not polling any devices
after:
# ps afx
294 ? Ss 0:00 /bin/dbus-daemon --system --nofork
426 ? Sl 0:00 \_ /usr/libexec/polkit-1/polkitd
449 ? S 0:00 \_ /usr/sbin/modem-manager
635 ? Sl 0:00 \_ /usr/libexec/colord
705 ? Sl 0:00 \_ /usr/libexec/upowerd
959 ? Sl 0:00 \_ /usr/libexec/udisks-daemon
960 ? S 0:00 | \_ udisks-daemon: not polling any devices
977 ? Sl 0:00 \_ /usr/libexec/packagekitd
This prctl is orthogonal to PID namespaces. PID namespaces are isolated
from each other, while a service management process usually requires the
services to live in the same namespace, to be able to talk to each
other.
Users of this will be the systemd per-user instance, which provides
init-like functionality for the user's login session and D-Bus, which
activates bus services on-demand. Both need init-like capabilities to
be able to properly keep track of the services they start.
Many thanks to Oleg for several rounds of review and insights.
[akpm@linux-foundation.org: fix comment layout and spelling]
[akpm@linux-foundation.org: add lengthy code comment from Oleg]
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge first batch of patches from Andrew Morton:
"A few misc things and all the MM queue"
* emailed from Andrew Morton <akpm@linux-foundation.org>: (92 commits)
memcg: avoid THP split in task migration
thp: add HPAGE_PMD_* definitions for !CONFIG_TRANSPARENT_HUGEPAGE
memcg: clean up existing move charge code
mm/memcontrol.c: remove unnecessary 'break' in mem_cgroup_read()
mm/memcontrol.c: remove redundant BUG_ON() in mem_cgroup_usage_unregister_event()
mm/memcontrol.c: s/stealed/stolen/
memcg: fix performance of mem_cgroup_begin_update_page_stat()
memcg: remove PCG_FILE_MAPPED
memcg: use new logic for page stat accounting
memcg: remove PCG_MOVE_LOCK flag from page_cgroup
memcg: simplify move_account() check
memcg: remove EXPORT_SYMBOL(mem_cgroup_update_page_stat)
memcg: kill dead prev_priority stubs
memcg: remove PCG_CACHE page_cgroup flag
memcg: let css_get_next() rely upon rcu_read_lock()
cgroup: revert ss_id_lock to spinlock
idr: make idr_get_next() good for rcu_read_lock()
memcg: remove unnecessary thp check in page stat accounting
memcg: remove redundant returns
memcg: enum lru_list lru
...
Commit c0ff7453bb ("cpuset,mm: fix no node to alloc memory when
changing cpuset's mems") wins a super prize for the largest number of
memory barriers entered into fast paths for one commit.
[get|put]_mems_allowed is incredibly heavy with pairs of full memory
barriers inserted into a number of hot paths. This was detected while
investigating at large page allocator slowdown introduced some time
after 2.6.32. The largest portion of this overhead was shown by
oprofile to be at an mfence introduced by this commit into the page
allocator hot path.
For extra style points, the commit introduced the use of yield() in an
implementation of what looks like a spinning mutex.
This patch replaces the full memory barriers on both read and write
sides with a sequence counter with just read barriers on the fast path
side. This is much cheaper on some architectures, including x86. The
main bulk of the patch is the retry logic if the nodemask changes in a
manner that can cause a false failure.
While updating the nodemask, a check is made to see if a false failure
is a risk. If it is, the sequence number gets bumped and parallel
allocators will briefly stall while the nodemask update takes place.
In a page fault test microbenchmark, oprofile samples from
__alloc_pages_nodemask went from 4.53% of all samples to 1.15%. The
actual results were
3.3.0-rc3 3.3.0-rc3
rc3-vanilla nobarrier-v2r1
Clients 1 UserTime 0.07 ( 0.00%) 0.08 (-14.19%)
Clients 2 UserTime 0.07 ( 0.00%) 0.07 ( 2.72%)
Clients 4 UserTime 0.08 ( 0.00%) 0.07 ( 3.29%)
Clients 1 SysTime 0.70 ( 0.00%) 0.65 ( 6.65%)
Clients 2 SysTime 0.85 ( 0.00%) 0.82 ( 3.65%)
Clients 4 SysTime 1.41 ( 0.00%) 1.41 ( 0.32%)
Clients 1 WallTime 0.77 ( 0.00%) 0.74 ( 4.19%)
Clients 2 WallTime 0.47 ( 0.00%) 0.45 ( 3.73%)
Clients 4 WallTime 0.38 ( 0.00%) 0.37 ( 1.58%)
Clients 1 Flt/sec/cpu 497620.28 ( 0.00%) 520294.53 ( 4.56%)
Clients 2 Flt/sec/cpu 414639.05 ( 0.00%) 429882.01 ( 3.68%)
Clients 4 Flt/sec/cpu 257959.16 ( 0.00%) 258761.48 ( 0.31%)
Clients 1 Flt/sec 495161.39 ( 0.00%) 517292.87 ( 4.47%)
Clients 2 Flt/sec 820325.95 ( 0.00%) 850289.77 ( 3.65%)
Clients 4 Flt/sec 1020068.93 ( 0.00%) 1022674.06 ( 0.26%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 135.68 132.17
User+Sys Time Running Test (seconds) 164.2 160.13
Total Elapsed Time (seconds) 123.46 120.87
The overall improvement is small but the System CPU time is much
improved and roughly in correlation to what oprofile reported (these
performance figures are without profiling so skew is expected). The
actual number of page faults is noticeably improved.
For benchmarks like kernel builds, the overall benefit is marginal but
the system CPU time is slightly reduced.
To test the actual bug the commit fixed I opened two terminals. The
first ran within a cpuset and continually ran a small program that
faulted 100M of anonymous data. In a second window, the nodemask of the
cpuset was continually randomised in a loop.
Without the commit, the program would fail every so often (usually
within 10 seconds) and obviously with the commit everything worked fine.
With this patch applied, it also worked fine so the fix should be
functionally equivalent.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Warn about non-zero rss counters at final mmdrop.
This check will prevent reoccurences of bugs such as that fixed in "mm:
fix rss count leakage during migration".
I didn't hide this check under CONFIG_VM_DEBUG because it rather small and
rss counters cover whole page-table management, so this is a good
invariant.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull security subsystem updates for 3.4 from James Morris:
"The main addition here is the new Yama security module from Kees Cook,
which was discussed at the Linux Security Summit last year. Its
purpose is to collect miscellaneous DAC security enhancements in one
place. This also marks a departure in policy for LSM modules, which
were previously limited to being standalone access control systems.
Chromium OS is using Yama, and I believe there are plans for Ubuntu,
at least.
This patchset also includes maintenance updates for AppArmor, TOMOYO
and others."
Fix trivial conflict in <net/sock.h> due to the jumo_label->static_key
rename.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (38 commits)
AppArmor: Fix location of const qualifier on generated string tables
TOMOYO: Return error if fails to delete a domain
AppArmor: add const qualifiers to string arrays
AppArmor: Add ability to load extended policy
TOMOYO: Return appropriate value to poll().
AppArmor: Move path failure information into aa_get_name and rename
AppArmor: Update dfa matching routines.
AppArmor: Minor cleanup of d_namespace_path to consolidate error handling
AppArmor: Retrieve the dentry_path for error reporting when path lookup fails
AppArmor: Add const qualifiers to generated string tables
AppArmor: Fix oops in policy unpack auditing
AppArmor: Fix error returned when a path lookup is disconnected
KEYS: testing wrong bit for KEY_FLAG_REVOKED
TOMOYO: Fix mount flags checking order.
security: fix ima kconfig warning
AppArmor: Fix the error case for chroot relative path name lookup
AppArmor: fix mapping of META_READ to audit and quiet flags
AppArmor: Fix underflow in xindex calculation
AppArmor: Fix dropping of allowed operations that are force audited
AppArmor: Add mising end of structure test to caps unpacking
...
The child must not control its ->exit_signal, it is the parent who
decides which signal the child should use for notification.
This means that CLONE_PARENT should not use "clone_flags & CSIGNAL",
the forking task is the sibling of the new process and their parent
doesn't control exit_signal in this case.
This patch uses ->exit_signal of the forking process, but perhaps
we should simply use SIGCHLD.
We read group_leader->exit_signal lockless, this can race with the
ORIGINAL_SIGNAL -> SIGCHLD transition, but this is fine.
Potentially this change allows to kill self_exec_id/parent_exec_id.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uprobes uses exception notifiers to get to know if a thread hit
a breakpoint or a singlestep exception.
When a thread hits a uprobe or is singlestepping post a uprobe
hit, the uprobe exception notifier sets its TIF_UPROBE bit,
which will then be checked on its return to userspace path
(do_notify_resume() ->uprobe_notify_resume()), where the
consumers handlers are run (in task context) based on the
defined filters.
Uprobe hits are thread specific and hence we need to maintain
information about if a task hit a uprobe, what uprobe was hit,
the slot where the original instruction was copied for xol so
that it can be singlestepped with appropriate fixups.
In some cases, special care is needed for instructions that are
executed out of line (xol). These are architecture specific
artefacts, such as handling RIP relative instructions on x86_64.
Since the instruction at which the uprobe was inserted is
executed out of line, architecture specific fixups are added so
that the thread continues normal execution in the presence of a
uprobe.
Postpone the signals until we execute the probed insn.
post_xol() path does a recalc_sigpending() before return to
user-mode, this ensures the signal can't be lost.
Uprobes relies on DIE_DEBUG notification to notify if a
singlestep is complete.
Adds x86 specific uprobe exception notifiers and appropriate
hooks needed to determine a uprobe hit and subsequent post
processing.
Add requisite x86 fixups for xol for uprobes. Specific cases
needing fixups include relative jumps (x86_64), calls, etc.
Where possible, we check and skip singlestepping the
breakpointed instructions. For now we skip single byte as well
as few multibyte nop instructions. However this can be extended
to other instructions too.
Credits to Oleg Nesterov for suggestions/patches related to
signal, breakpoint, singlestep handling code.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120313180011.29771.89027.sendpatchset@srdronam.in.ibm.com
[ Performed various cleanliness edits ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ioc_task_link() is used to share %current's ioc on clone. If
%current->io_context is set, %current is guaranteed to have refcount
on the ioc and, thus, ioc_task_link() can't fail.
Replace error checking in ioc_task_link() with WARN_ON_ONCE() and make
it just increment refcount and nr_tasks.
-v2: Description typo fix (Vivek).
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previously it was (ab)used by utrace. Then it was wrongly used by the
scheduler code.
Currently it is not used, kill it before it finds the new erroneous user.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that CLONE_VFORK is killable, coredump_wait() no longer needs
complete_vfork_done(). zap_threads() should find and kill all tasks with
the same ->mm, this includes our parent if ->vfork_done is set.
mm_release() becomes the only caller, unexport complete_vfork_done().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make vfork() killable.
Change do_fork(CLONE_VFORK) to do wait_for_completion_killable(). If it
fails we do not return to the user-mode and never touch the memory shared
with our child.
However, in this case we should clear child->vfork_done before return, we
use task_lock() in do_fork()->wait_for_vfork_done() and
complete_vfork_done() to serialize with each other.
Note: now that we use task_lock() we don't really need completion, we
could turn task->vfork_done into "task_struct *wake_up_me" but this needs
some complications.
NOTE: this and the next patches do not affect in-kernel users of
CLONE_VFORK, kernel threads run with all signals ignored including
SIGKILL/SIGSTOP.
However this is obviously the user-visible change. Not only a fatal
signal can kill the vforking parent, a sub-thread can do execve or
exit_group() and kill the thread sleeping in vfork().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional changes.
Move the clear-and-complete-vfork_done code into the new trivial helper,
complete_vfork_done().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is intentionally incomplete to simplify the review.
It ignores ep_unregister_pollwait() which plays with the same wqh.
See the next change.
epoll assumes that the EPOLL_CTL_ADD'ed file controls everything
f_op->poll() needs. In particular it assumes that the wait queue
can't go away until eventpoll_release(). This is not true in case
of signalfd, the task which does EPOLL_CTL_ADD uses its ->sighand
which is not connected to the file.
This patch adds the special event, POLLFREE, currently only for
epoll. It expects that init_poll_funcptr()'ed hook should do the
necessary cleanup. Perhaps it should be defined as EPOLLFREE in
eventpoll.
__cleanup_sighand() is changed to do wake_up_poll(POLLFREE) if
->signalfd_wqh is not empty, we add the new signalfd_cleanup()
helper.
ep_poll_callback(POLLFREE) simply does list_del_init(task_list).
This make this poll entry inconsistent, but we don't care. If you
share epoll fd which contains our sigfd with another process you
should blame yourself. signalfd is "really special". I simply do
not know how we can define the "right" semantics if it used with
epoll.
The main problem is, epoll calls signalfd_poll() once to establish
the connection with the wait queue, after that signalfd_poll(NULL)
returns the different/inconsistent results depending on who does
EPOLL_CTL_MOD/signalfd_read/etc. IOW: apart from sigmask, signalfd
has nothing to do with the file, it works with the current thread.
In short: this patch is the hack which tries to fix the symptoms.
It also assumes that nobody can take tasklist_lock under epoll
locks, this seems to be true.
Note:
- we do not have wake_up_all_poll() but wake_up_poll()
is fine, poll/epoll doesn't use WQ_FLAG_EXCLUSIVE.
- signalfd_cleanup() uses POLLHUP along with POLLFREE,
we need a couple of simple changes in eventpoll.c to
make sure it can't be "lost".
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Cc: <stable@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Collapse security_vm_enough_memory() variants into a single function.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Morris <jmorris@namei.org>
Says Jens:
"Time to push off some of the pending items. I really wanted to wait
until we had the regression nailed, but alas it's not quite there yet.
But I'm very confident that it's "just" a missing expire on exit, so
fix from Tejun should be fairly trivial. I'm headed out for a week on
the slopes.
- Killing the barrier part of mtip32xx. It doesn't really support
barriers, and it doesn't need them (writes are fully ordered).
- A few fixes from Dan Carpenter, preventing overflows of integer
multiplication.
- A fixup for loop, fixing a previous commit that didn't quite solve
the partial read problem from Dave Young.
- A bio integer overflow fix from Kent Overstreet.
- Improvement/fix of the door "keep locked" part of the cdrom shared
code from Paolo Benzini.
- A few cfq fixes from Shaohua Li.
- A fix for bsg sysfs warning when removing a file it did not create
from Stanislaw Gruszka.
- Two fixes for floppy from Vivek, preventing a crash.
- A few block core fixes from Tejun. One killing the over-optimized
ioc exit path, cleaning that up nicely. Two others fixing an oops
on elevator switch, due to calling into the scheduler merge check
code without holding the queue lock."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix lockdep warning on io_context release put_io_context()
relay: prevent integer overflow in relay_open()
loop: zero fill bio instead of return -EIO for partial read
bio: don't overflow in bio_get_nr_vecs()
floppy: Fix a crash during rmmod
floppy: Cleanup disk->queue before caling put_disk() if add_disk() was never called
cdrom: move shared static to cdrom_device_info
bsg: fix sysfs link remove warning
block: don't call elevator callbacks for plug merges
block: separate out blk_rq_merge_ok() and blk_try_merge() from elevator functions
mtip32xx: removed the irrelevant argument of mtip_hw_submit_io() and the unused member of struct driver_data
block: strip out locking optimization in put_io_context()
cdrom: use copy_to_user() without the underscores
block: fix ioc locking warning
block: fix NULL icq_cache reference
block,cfq: change code order
The current LSM interface to cred_free is not sufficient for allowing
an LSM to track the life and death of a task. This patch adds the
task_free hook so that an LSM can clean up resources on task death.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <jmorris@namei.org>
put_io_context() performed a complex trylock dancing to avoid
deferring ioc release to workqueue. It was also broken on UP because
trylock was always assumed to succeed which resulted in unbalanced
preemption count.
While there are ways to fix the UP breakage, even the most
pathological microbench (forced ioc allocation and tight fork/exit
loop) fails to show any appreciable performance benefit of the
optimization. Strip it out. If there turns out to be workloads which
are affected by this change, simpler optimization from the discussion
thread can be applied later.
Signed-off-by: Tejun Heo <tj@kernel.org>
LKML-Reference: <1328514611.21268.66.camel@sli10-conroe>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This fixes the race in process_vm_core found by Oleg (see
http://article.gmane.org/gmane.linux.kernel/1235667/
for details).
This has been updated since I last sent it as the creation of the new
mm_access() function did almost exactly the same thing as parts of the
previous version of this patch did.
In order to use mm_access() even when /proc isn't enabled, we move it to
kernel/fork.c where other related process mm access functions already
are.
Signed-off-by: Chris Yeoh <yeohc@au1.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit: (29 commits)
audit: no leading space in audit_log_d_path prefix
audit: treat s_id as an untrusted string
audit: fix signedness bug in audit_log_execve_info()
audit: comparison on interprocess fields
audit: implement all object interfield comparisons
audit: allow interfield comparison between gid and ogid
audit: complex interfield comparison helper
audit: allow interfield comparison in audit rules
Kernel: Audit Support For The ARM Platform
audit: do not call audit_getname on error
audit: only allow tasks to set their loginuid if it is -1
audit: remove task argument to audit_set_loginuid
audit: allow audit matching on inode gid
audit: allow matching on obj_uid
audit: remove audit_finish_fork as it can't be called
audit: reject entry,always rules
audit: inline audit_free to simplify the look of generic code
audit: drop audit_set_macxattr as it doesn't do anything
audit: inline checks for not needing to collect aux records
audit: drop some potentially inadvisable likely notations
...
Use evil merge to fix up grammar mistakes in Kconfig file.
Bad speling and horrible grammar (and copious swearing) is to be
expected, but let's keep it to commit messages and comments, rather than
expose it to users in config help texts or printouts.
Audit entry,always rules are not allowed and are automatically changed in
exit,always rules in userspace. The kernel refuses to load such rules.
Thus a task in the middle of a syscall (and thus in audit_finish_fork())
can only be in one of two states: AUDIT_BUILD_CONTEXT or AUDIT_DISABLED.
Since the current task cannot be in AUDIT_RECORD_CONTEXT we aren't every
going to actually use the code in audit_finish_fork() since it will
return without doing anything. Thus drop the code.
Signed-off-by: Eric Paris <eparis@redhat.com>
* 'for-3.3/core' of git://git.kernel.dk/linux-block: (37 commits)
Revert "block: recursive merge requests"
block: Stop using macro stubs for the bio data integrity calls
blockdev: convert some macros to static inlines
fs: remove unneeded plug in mpage_readpages()
block: Add BLKROTATIONAL ioctl
block: Introduce blk_set_stacking_limits function
block: remove WARN_ON_ONCE() in exit_io_context()
block: an exiting task should be allowed to create io_context
block: ioc_cgroup_changed() needs to be exported
block: recursive merge requests
block, cfq: fix empty queue crash caused by request merge
block, cfq: move icq creation and rq->elv.icq association to block core
block, cfq: restructure io_cq creation path for io_context interface cleanup
block, cfq: move io_cq exit/release to blk-ioc.c
block, cfq: move icq cache management to block core
block, cfq: move io_cq lookup to blk-ioc.c
block, cfq: move cfqd->icq_list to request_queue and add request->elv.icq
block, cfq: reorganize cfq_io_context into generic and cfq specific parts
block: remove elevator_queue->ops
block: reorder elevator switch sequence
...
Fix up conflicts in:
- block/blk-cgroup.c
Switch from can_attach_task to can_attach
- block/cfq-iosched.c
conflict with now removed cic index changes (we now use q->id instead)
oom_score_adj is used for guarding processes from OOM-Killer. One of
problem is that it's inherited at fork(). When a daemon set oom_score_adj
and make children, it's hard to know where the value is set.
This patch adds some tracepoints useful for debugging. This patch adds
3 trace points.
- creating new task
- renaming a task (exec)
- set oom_score_adj
To debug, users need to enable some trace pointer. Maybe filtering is useful as
# EVENT=/sys/kernel/debug/tracing/events/task/
# echo "oom_score_adj != 0" > $EVENT/task_newtask/filter
# echo "oom_score_adj != 0" > $EVENT/task_rename/filter
# echo 1 > $EVENT/enable
# EVENT=/sys/kernel/debug/tracing/events/oom/
# echo 1 > $EVENT/enable
output will be like this.
# grep oom /sys/kernel/debug/tracing/trace
bash-7699 [007] d..3 5140.744510: oom_score_adj_update: pid=7699 comm=bash oom_score_adj=-1000
bash-7699 [007] ...1 5151.818022: task_newtask: pid=7729 comm=bash clone_flags=1200011 oom_score_adj=-1000
ls-7729 [003] ...2 5151.818504: task_rename: pid=7729 oldcomm=bash newcomm=ls oom_score_adj=-1000
bash-7699 [002] ...1 5175.701468: task_newtask: pid=7730 comm=bash clone_flags=1200011 oom_score_adj=-1000
grep-7730 [007] ...2 5175.701993: task_rename: pid=7730 oldcomm=bash newcomm=grep oom_score_adj=-1000
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
cgroup: fix to allow mounting a hierarchy by name
cgroup: move assignement out of condition in cgroup_attach_proc()
cgroup: Remove task_lock() from cgroup_post_fork()
cgroup: add sparse annotation to cgroup_iter_start() and cgroup_iter_end()
cgroup: mark cgroup_rmdir_waitq and cgroup_attach_proc() as static
cgroup: only need to check oldcgrp==newgrp once
cgroup: remove redundant get/put of task struct
cgroup: remove redundant get/put of old css_set from migrate
cgroup: Remove unnecessary task_lock before fetching css_set on migration
cgroup: Drop task_lock(parent) on cgroup_fork()
cgroups: remove redundant get/put of css_set from css_set_check_fetched()
resource cgroups: remove bogus cast
cgroup: kill subsys->can_attach_task(), pre_attach() and attach_task()
cgroup, cpuset: don't use ss->pre_attach()
cgroup: don't use subsys->can_attach_task() or ->attach_task()
cgroup: introduce cgroup_taskset and use it in subsys->can_attach(), cancel_attach() and attach()
cgroup: improve old cgroup handling in cgroup_attach_proc()
cgroup: always lock threadgroup during migration
threadgroup: extend threadgroup_lock() to cover exit and exec
threadgroup: rename signal->threadgroup_fork_lock to ->group_rwsem
...
Fix up conflict in kernel/cgroup.c due to commit e0197aae59e5: "cgroups:
fix a css_set not found bug in cgroup_attach_proc" that already
mentioned that the bug is fixed (differently) in Tejun's cgroup
patchset. This one, in other words.
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
Compensate the task's think time when computing the final pause time,
so that ->dirty_ratelimit can be executed accurately.
think time := time spend outside of balance_dirty_pages()
In the rare case that the task slept longer than the 200ms period time
(result in negative pause time), the sleep time will be compensated in
the following periods, too, if it's less than 1 second.
Accumulated errors are carefully avoided as long as the max pause area
is not hitted.
Pseudo code:
period = pages_dirtied / task_ratelimit;
think = jiffies - dirty_paused_when;
pause = period - think;
1) normal case: period > think
pause = period - think
dirty_paused_when = jiffies + pause
nr_dirtied = 0
period time
|===============================>|
think time pause time
|===============>|==============>|
------|----------------|---------------|------------------------
dirty_paused_when jiffies
2) no pause case: period <= think
don't pause; reduce future pause time by:
dirty_paused_when += period
nr_dirtied = 0
period time
|===============================>|
think time
|===================================================>|
------|--------------------------------+-------------------|----
dirty_paused_when jiffies
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Make cputime_t and cputime64_t nocast to enable sparse checking to
detect incorrect use of cputime. Drop the cputime macros for simple
scalar operations. The conversion macros are still needed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cic is association between io_context and request_queue. A cic is
linked from both ioc and q and should be destroyed when either one
goes away. As ioc and q both have their own locks, locking becomes a
bit complex - both orders work for removal from one but not from the
other.
Currently, cfq tries to circumvent this locking order issue with RCU.
ioc->lock nests inside queue_lock but the radix tree and cic's are
also protected by RCU allowing either side to walk their lists without
grabbing lock.
This rather unconventional use of RCU quickly devolves into extremely
fragile convolution. e.g. The following is from cfqd going away too
soon after ioc and q exits raced.
general protection fault: 0000 [#1] PREEMPT SMP
CPU 2
Modules linked in:
[ 88.503444]
Pid: 599, comm: hexdump Not tainted 3.1.0-rc10-work+ #158 Bochs Bochs
RIP: 0010:[<ffffffff81397628>] [<ffffffff81397628>] cfq_exit_single_io_context+0x58/0xf0
...
Call Trace:
[<ffffffff81395a4a>] call_for_each_cic+0x5a/0x90
[<ffffffff81395ab5>] cfq_exit_io_context+0x15/0x20
[<ffffffff81389130>] exit_io_context+0x100/0x140
[<ffffffff81098a29>] do_exit+0x579/0x850
[<ffffffff81098d5b>] do_group_exit+0x5b/0xd0
[<ffffffff81098de7>] sys_exit_group+0x17/0x20
[<ffffffff81b02f2b>] system_call_fastpath+0x16/0x1b
The only real hot path here is cic lookup during request
initialization and avoiding extra locking requires very confined use
of RCU. This patch makes cic removal from both ioc and request_queue
perform double-locking and unlink immediately.
* From q side, the change is almost trivial as ioc->lock nests inside
queue_lock. It just needs to grab each ioc->lock as it walks
cic_list and unlink it.
* From ioc side, it's a bit more difficult because of inversed lock
order. ioc needs its lock to walk its cic_list but can't grab the
matching queue_lock and needs to perform unlock-relock dancing.
Unlinking is now wholly done from put_io_context() and fast path is
optimized by using the queue_lock the caller already holds, which is
by far the most common case. If the ioc accessed multiple devices,
it tries with trylock. In unlikely cases of fast path failure, it
falls back to full double-locking dance from workqueue.
Double-locking isn't the prettiest thing in the world but it's *far*
simpler and more understandable than RCU trick without adding any
meaningful overhead.
This still leaves a lot of now unnecessary RCU logics. Future patches
will trim them.
-v2: Vivek pointed out that cic->q was being dereferenced after
cic->release() was called. Updated to use local variable @this_q
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ignoring copy_io() during fork, io_context can be allocated from two
places - current_io_context() and set_task_ioprio(). The former is
always called from local task while the latter can be called from
different task. The synchornization between them are peculiar and
dubious.
* current_io_context() doesn't grab task_lock() and assumes that if it
saw %NULL ->io_context, it would stay that way until allocation and
assignment is complete. It has smp_wmb() between alloc/init and
assignment.
* set_task_ioprio() grabs task_lock() for assignment and does
smp_read_barrier_depends() between "ioc = task->io_context" and "if
(ioc)". Unfortunately, this doesn't achieve anything - the latter
is not a dependent load of the former. ie, if ioc itself were being
dereferenced "ioc->xxx", it would mean something (not sure what tho)
but as the code currently stands, the dependent read barrier is
noop.
As only one of the the two test-assignment sequences is task_lock()
protected, the task_lock() can't do much about race between the two.
Nothing prevents current_io_context() and set_task_ioprio() allocating
its own ioc for the same task and overwriting the other's.
Also, set_task_ioprio() can race with exiting task and create a new
ioc after exit_io_context() is finished.
ioc get/put doesn't have any reason to be complex. The only hot path
is accessing the existing ioc of %current, which is simple to achieve
given that ->io_context is never destroyed as long as the task is
alive. All other paths can happily go through task_lock() like all
other task sub structures without impacting anything.
This patch updates ioc get/put so that it becomes more conventional.
* alloc_io_context() is replaced with get_task_io_context(). This is
the only interface which can acquire access to ioc of another task.
On return, the caller has an explicit reference to the object which
should be put using put_io_context() afterwards.
* The functionality of current_io_context() remains the same but when
creating a new ioc, it shares the code path with
get_task_io_context() and always goes through task_lock().
* get_io_context() now means incrementing ref on an ioc which the
caller already has access to (be that an explicit refcnt or implicit
%current one).
* PF_EXITING inhibits creation of new io_context and once
exit_io_context() is finished, it's guaranteed that both ioc
acquisition functions return %NULL.
* All users are updated. Most are trivial but
smp_read_barrier_depends() removal from cfq_get_io_context() needs a
bit of explanation. I suppose the original intention was to ensure
ioc->ioprio is visible when set_task_ioprio() allocates new
io_context and installs it; however, this wouldn't have worked
because set_task_ioprio() doesn't have wmb between init and install.
There are other problems with this which will be fixed in another
patch.
* While at it, use NUMA_NO_NODE instead of -1 for wildcard node
specification.
-v2: Vivek spotted contamination from debug patch. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make the following renames to prepare for extension of threadgroup
locking.
* s/signal->threadgroup_fork_lock/signal->group_rwsem/
* s/threadgroup_fork_read_lock()/threadgroup_change_begin()/
* s/threadgroup_fork_read_unlock()/threadgroup_change_end()/
* s/threadgroup_fork_write_lock()/threadgroup_lock()/
* s/threadgroup_fork_write_unlock()/threadgroup_unlock()/
This patch doesn't cause any behavior change.
-v2: Rename threadgroup_change_done() to threadgroup_change_end() per
KAMEZAWA's suggestion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Menage <paul@paulmenage.org>
* 'pm-freezer' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc: (24 commits)
freezer: fix wait_event_freezable/__thaw_task races
freezer: kill unused set_freezable_with_signal()
dmatest: don't use set_freezable_with_signal()
usb_storage: don't use set_freezable_with_signal()
freezer: remove unused @sig_only from freeze_task()
freezer: use lock_task_sighand() in fake_signal_wake_up()
freezer: restructure __refrigerator()
freezer: fix set_freezable[_with_signal]() race
freezer: remove should_send_signal() and update frozen()
freezer: remove now unused TIF_FREEZE
freezer: make freezing() test freeze conditions in effect instead of TIF_FREEZE
cgroup_freezer: prepare for removal of TIF_FREEZE
freezer: clean up freeze_processes() failure path
freezer: kill PF_FREEZING
freezer: test freezable conditions while holding freezer_lock
freezer: make freezing indicate freeze condition in effect
freezer: use dedicated lock instead of task_lock() + memory barrier
freezer: don't distinguish nosig tasks on thaw
freezer: remove racy clear_freeze_flag() and set PF_NOFREEZE on dead tasks
freezer: rename thaw_process() to __thaw_task() and simplify the implementation
...
Using TIF_FREEZE for freezing worked when there was only single
freezing condition (the PM one); however, now there is also the
cgroup_freezer and single bit flag is getting clumsy.
thaw_processes() is already testing whether cgroup freezing in in
effect to avoid thawing tasks which were frozen by both PM and cgroup
freezers.
This is racy (nothing prevents race against cgroup freezing) and
fragile. A much simpler way is to test actual freeze conditions from
freezing() - ie. directly test whether PM or cgroup freezing is in
effect.
This patch adds variables to indicate whether and what type of
freezing conditions are in effect and reimplements freezing() such
that it directly tests whether any of the two freezing conditions is
active and the task should freeze. On fast path, freezing() is still
very cheap - it only tests system_freezing_cnt.
This makes the clumsy dancing aroung TIF_FREEZE unnecessary and
freeze/thaw operations more usual - updating state variables for the
new state and nudging target tasks so that they notice the new state
and comply. As long as the nudging happens after state update, it's
race-free.
* This allows use of freezing() in freeze_task(). Replace the open
coded tests with freezing().
* p != current test is added to warning printing conditions in
try_to_freeze_tasks() failure path. This is necessary as freezing()
is now true for the task which initiated freezing too.
-v2: Oleg pointed out that re-freezing FROZEN cgroup could increment
system_freezing_cnt. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Paul Menage <paul@paulmenage.org> (for the cgroup portions)
* 'writeback-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Add a 'reason' to wb_writeback_work
writeback: send work item to queue_io, move_expired_inodes
writeback: trace event balance_dirty_pages
writeback: trace event bdi_dirty_ratelimit
writeback: fix ppc compile warnings on do_div(long long, unsigned long)
writeback: per-bdi background threshold
writeback: dirty position control - bdi reserve area
writeback: control dirty pause time
writeback: limit max dirty pause time
writeback: IO-less balance_dirty_pages()
writeback: per task dirty rate limit
writeback: stabilize bdi->dirty_ratelimit
writeback: dirty rate control
writeback: add bg_threshold parameter to __bdi_update_bandwidth()
writeback: dirty position control
writeback: account per-bdi accumulated dirtied pages
This removes mm->oom_disable_count entirely since it's unnecessary and
currently buggy. The counter was intended to be per-process but it's
currently decremented in the exit path for each thread that exits, causing
it to underflow.
The count was originally intended to prevent oom killing threads that
share memory with threads that cannot be killed since it doesn't lead to
future memory freeing. The counter could be fixed to represent all
threads sharing the same mm, but it's better to remove the count since:
- it is possible that the OOM_DISABLE thread sharing memory with the
victim is waiting on that thread to exit and will actually cause
future memory freeing, and
- there is no guarantee that a thread is disabled from oom killing just
because another thread sharing its mm is oom disabled.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two fields to task_struct.
1) account dirtied pages in the individual tasks, for accuracy
2) per-task balance_dirty_pages() call intervals, for flexibility
The balance_dirty_pages() call interval (ie. nr_dirtied_pause) will
scale near-sqrt to the safety gap between dirty pages and threshold.
The main problem of per-task nr_dirtied is, if 1k+ tasks start dirtying
pages at exactly the same time, each task will be assigned a large
initial nr_dirtied_pause, so that the dirty threshold will be exceeded
long before each task reached its nr_dirtied_pause and hence call
balance_dirty_pages().
The solution is to watch for the number of pages dirtied on each CPU in
between the calls into balance_dirty_pages(). If it exceeds ratelimit_pages
(3% dirty threshold), force call balance_dirty_pages() for a chance to
set bdi->dirty_exceeded. In normal situations, this safeguarding
condition is not expected to trigger at all.
On the sqrt in dirty_poll_interval():
It will serve as an initial guess when dirty pages are still in the
freerun area.
When dirty pages are floating inside the dirty control scope [freerun,
limit], a followup patch will use some refined dirty poll interval to
get the desired pause time.
thresh-dirty (MB) sqrt
1 16
2 22
4 32
8 45
16 64
32 90
64 128
128 181
256 256
512 362
1024 512
The above table means, given 1MB (or 1GB) gap and the dd tasks polling
balance_dirty_pages() on every 16 (or 512) pages, the dirty limit won't
be exceeded as long as there are less than 16 (or 512) concurrent dd's.
So sqrt naturally leads to less overheads and more safe concurrent tasks
for large memory servers, which have large (thresh-freerun) gaps.
peter: keep the per-CPU ratelimit for safeguarding the 1k+ tasks case
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Andrea Righi <andrea@betterlinux.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
The patch http://lkml.org/lkml/2003/7/13/226 introduced an RLIMIT_NPROC
check in set_user() to check for NPROC exceeding via setuid() and
similar functions.
Before the check there was a possibility to greatly exceed the allowed
number of processes by an unprivileged user if the program relied on
rlimit only. But the check created new security threat: many poorly
written programs simply don't check setuid() return code and believe it
cannot fail if executed with root privileges. So, the check is removed
in this patch because of too often privilege escalations related to
buggy programs.
The NPROC can still be enforced in the common code flow of daemons
spawning user processes. Most of daemons do fork()+setuid()+execve().
The check introduced in execve() (1) enforces the same limit as in
setuid() and (2) doesn't create similar security issues.
Neil Brown suggested to track what specific process has exceeded the
limit by setting PF_NPROC_EXCEEDED process flag. With the change only
this process would fail on execve(), and other processes' execve()
behaviour is not changed.
Solar Designer suggested to re-check whether NPROC limit is still
exceeded at the moment of execve(). If the process was sleeping for
days between set*uid() and execve(), and the NPROC counter step down
under the limit, the defered execve() failure because NPROC limit was
exceeded days ago would be unexpected. If the limit is not exceeded
anymore, we clear the flag on successful calls to execve() and fork().
The flag is also cleared on successful calls to set_user() as the limit
was exceeded for the previous user, not the current one.
Similar check was introduced in -ow patches (without the process flag).
v3 - clear PF_NPROC_EXCEEDED on successful calls to set_user().
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Rebelo de Oliveira <psykon@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ This patch has already been accepted as commit 0ac0c0d0f8 but later
reverted (commit 35926ff5fb) because it itroduced arch specific
__node_random which was defined only for x86 code so it broke other
archs. This is a followup without any arch specific code. Other than
that there are no functional changes.]
Some workloads that create a large number of small files tend to assign
too many pages to node 0 (multi-node systems). Part of the reason is
that the rotor (in cpuset_mem_spread_node()) used to assign nodes starts
at node 0 for newly created tasks.
This patch changes the rotor to be initialized to a random node number
of the cpuset.
[akpm@linux-foundation.org: fix layout]
[Lee.Schermerhorn@hp.com: Define stub numa_random() for !NUMA configuration]
[mhocko@suse.cz: Make it arch independent]
[akpm@linux-foundation.org: fix CONFIG_NUMA=y, MAX_NUMNODES>1 build]
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Paul Menage <menage@google.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Paul Menage <menage@google.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-3.1/core' of git://git.kernel.dk/linux-block: (24 commits)
block: strict rq_affinity
backing-dev: use synchronize_rcu_expedited instead of synchronize_rcu
block: fix patch import error in max_discard_sectors check
block: reorder request_queue to remove 64 bit alignment padding
CFQ: add think time check for group
CFQ: add think time check for service tree
CFQ: move think time check variables to a separate struct
fixlet: Remove fs_excl from struct task.
cfq: Remove special treatment for metadata rqs.
block: document blk_plug list access
block: avoid building too big plug list
compat_ioctl: fix make headers_check regression
block: eliminate potential for infinite loop in blkdev_issue_discard
compat_ioctl: fix warning caused by qemu
block: flush MEDIA_CHANGE from drivers on close(2)
blk-throttle: Make total_nr_queued unsigned
block: Add __attribute__((format(printf...) and fix fallout
fs/partitions/check.c: make local symbols static
block:remove some spare spaces in genhd.c
block:fix the comment error in blkdev.h
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: Fix lockdep_no_validate against IRQ states
mutex: Make mutex_destroy() an inline function
plist: Remove the need to supply locks to plist heads
lockup detector: Fix reference to the non-existent CONFIG_DETECT_SOFTLOCKUP option
If the new child is traced, do_fork() adds the pending SIGSTOP.
It assumes that either it is traced because of auto-attach or the
tracer attached later, in both cases sigaddset/set_thread_flag is
correct even if SIGSTOP is already pending.
Now that we have PTRACE_SEIZE this is no longer right in the latter
case. If the tracer does PTRACE_SEIZE after copy_process() makes the
child visible the queued SIGSTOP is wrong.
We could check PT_SEIZED bit and change ptrace_attach() to set both
PT_PTRACED and PT_SEIZED bits simultaneously but see the next patch,
we need to know whether this child was auto-attached or not anyway.
So this patch simply moves this code to ptrace_init_task(), this
way we can never race with ptrace_attach().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
fs_excl is a poor man's priority inheritance for filesystems to hint to
the block layer that an operation is important. It was never clearly
specified, not widely adopted, and will not prevent starvation in many
cases (like across cgroups).
fs_excl was introduced with the time sliced CFQ IO scheduler, to
indicate when a process held FS exclusive resources and thus needed
a boost.
It doesn't cover all file systems, and it was never fully complete.
Lets kill it.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This was legacy code brought over from the RT tree and
is no longer necessary.
Signed-off-by: Dima Zavin <dima@android.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Walker <dwalker@codeaurora.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/1310084879-10351-2-git-send-email-dima@android.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At this point, tracehooks aren't useful to mainline kernel and mostly
just add an extra layer of obfuscation. Although they have comments,
without actual in-kernel users, it is difficult to tell what are their
assumptions and they're actually trying to achieve. To mainline
kernel, they just aren't worth keeping around.
This patch kills the following clone and exec related tracehooks.
tracehook_prepare_clone()
tracehook_finish_clone()
tracehook_report_clone()
tracehook_report_clone_complete()
tracehook_unsafe_exec()
The changes are mostly trivial - logic is moved to the caller and
comments are merged and adjusted appropriately.
The only exception is in check_unsafe_exec() where LSM_UNSAFE_PTRACE*
are OR'd to bprm->unsafe instead of setting it, which produces the
same result as the field is always zero on entry. It also tests
p->ptrace instead of (p->ptrace & PT_PTRACED) for consistency, which
also gives the same result.
This doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
At this point, tracehooks aren't useful to mainline kernel and mostly
just add an extra layer of obfuscation. Although they have comments,
without actual in-kernel users, it is difficult to tell what are their
assumptions and they're actually trying to achieve. To mainline
kernel, they just aren't worth keeping around.
This patch kills the following trivial tracehooks.
* Ones testing whether task is ptraced. Replace with ->ptrace test.
tracehook_expect_breakpoints()
tracehook_consider_ignored_signal()
tracehook_consider_fatal_signal()
* ptrace_event() wrappers. Call directly.
tracehook_report_exec()
tracehook_report_exit()
tracehook_report_vfork_done()
* ptrace_release_task() wrapper. Call directly.
tracehook_finish_release_task()
* noop
tracehook_prepare_release_task()
tracehook_report_death()
This doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Thomas Gleixner reports that we now have a boot crash triggered by
CONFIG_CPUMASK_OFFSTACK=y:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c11ae035>] find_next_bit+0x55/0xb0
Call Trace:
[<c11addda>] cpumask_any_but+0x2a/0x70
[<c102396b>] flush_tlb_mm+0x2b/0x80
[<c1022705>] pud_populate+0x35/0x50
[<c10227ba>] pgd_alloc+0x9a/0xf0
[<c103a3fc>] mm_init+0xec/0x120
[<c103a7a3>] mm_alloc+0x53/0xd0
which was introduced by commit de03c72cfc ("mm: convert
mm->cpu_vm_cpumask into cpumask_var_t"), and is due to wrong ordering of
mm_init() vs mm_init_cpumask
Thomas wrote a patch to just fix the ordering of initialization, but I
hate the new double allocation in the fork path, so I ended up instead
doing some more radical surgery to clean it all up.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setup and cleanup of mm_struct->exe_file is currently done in fs/proc/.
This was because exe_file was needed only for /proc/<pid>/exe. Since we
will need the exe_file functionality also for core dumps (so core name can
contain full binary path), built this functionality always into the
kernel.
To achieve that move that out of proc FS to the kernel/ where in fact it
should belong. By doing that we can make dup_mm_exe_file static. Also we
can drop linux/proc_fs.h inclusion in fs/exec.c and kernel/fork.c.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:
* cgroup creation is out-of-control
* cgroup name can conflict when pids are looping
* it is not possible to have a single process handling a lot of
namespaces without falling in a exponential creation time
* we may want to create a namespace without creating a cgroup
The ns_cgroup was replaced by a compatibility flag 'clone_children',
where a newly created cgroup will copy the parent cgroup values.
The userspace has to manually create a cgroup and add a task to
the 'tasks' file.
This patch removes the ns_cgroup as suggested in the following thread:
https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html
The 'cgroup_clone' function is removed because it is no longer used.
This is a userspace-visible change. Commit 45531757b4 ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal. Since that
time we have heard from XXX users who were affected by this.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds functionality to read/write lock CLONE_THREAD fork()ing per-threadgroup
Add an rwsem that lives in a threadgroup's signal_struct that's taken for
reading in the fork path, under CONFIG_CGROUPS. If another part of the
kernel later wants to use such a locking mechanism, the CONFIG_CGROUPS
ifdefs should be changed to a higher-up flag that CGROUPS and the other
system would both depend on.
This is a pre-patch for cgroup-procs-write.patch.
Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpumask_t is very big struct and cpu_vm_mask is placed wrong position.
It might lead to reduce cache hit ratio.
This patch has two change.
1) Move the place of cpumask into last of mm_struct. Because usually cpumask
is accessed only front bits when the system has cpu-hotplug capability
2) Convert cpu_vm_mask into cpumask_var_t. It may help to reduce memory
footprint if cpumask_size() will use nr_cpumask_bits properly in future.
In addition, this patch change the name of cpu_vm_mask with cpu_vm_mask_var.
It may help to detect out of tree cpu_vm_mask users.
This patch has no functional change.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straightforward conversion of i_mmap_lock to a mutex.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh says:
"The only significant loser, I think, would be page reclaim (when
concurrent with truncation): could spin for a long time waiting for
the i_mmap_mutex it expects would soon be dropped? "
Counter points:
- cpu contention makes the spin stop (need_resched())
- zap pages should be freeing pages at a higher rate than reclaim
ever can
I think the simplification of the truncate code is definitely worth it.
Effectively reverts: 2aa15890f3 ("mm: prevent concurrent
unmap_mapping_range() on the same inode") and takes out the code that
caused its problem.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sched_fork() and wake_up_new_task() are defined with a parameter
'unsigned long clone_flags', which is unused.
This patch removes the parameters.
Signed-off-by: Samir Bellabes <sam@synack.fr>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1305130685-1047-1-git-send-email-sam@synack.fr
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Neil Brown pointed out that lock_depth somehow escaped the BKL
removal work. Let's get rid of it now.
Note that the perf scripting utilities still have a bunch of
code for dealing with common_lock_depth in tracepoints; I have
left that in place in case anybody wants to use that code with
older kernels.
Suggested-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20110422111910.456c0e84@bike.lwn.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
Reorganize proc_get_sb() so it can be called before the struct pid of the
first process is allocated.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Serge E. Hallyn <serge@hallyn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset is a cleanup and a preparation to unshare the pid namespace.
These prerequisites prepare for Eric's patchset to give a file descriptor
to a namespace and join an existing namespace.
This patch:
It turns out that the existing assignment in copy_process of the
child_reaper can handle the initial assignment of child_reaper we just
need to generalize the test in kernel/fork.c
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Serge E. Hallyn <serge@hallyn.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup: kill the dead code which does nothing but complicates the code
and confuses the reader.
sys_unshare(CLONE_THREAD/SIGHAND/VM) is not really implemented, and I
doubt very much it will ever work. At least, nobody even tried since the
original 99d1419d96 ("unshare system call -v5: system call
handler function") was applied more than 4 years ago.
And the code is not consistent. unshare_thread() always fails
unconditionally, while unshare_sighand() and unshare_vm() pretend to work
if there is nothing to unshare.
Remove unshare_thread(), unshare_sighand(), unshare_vm() helpers and
related variables and add a simple CLONE_THREAD | CLONE_SIGHAND| CLONE_VM
check into check_unshare_flags().
Also, move the "CLONE_NEWNS needs CLONE_FS" check from
check_unshare_flags() to sys_unshare(). This looks more consistent and
matches the similar do_sysvsem check in sys_unshare().
Note: with or without this patch "atomic_read(mm->mm_users) > 1" can give
a false positive due to get_task_mm().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Janak Desai <janak@us.ibm.com>
Cc: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All kthreads being created from a single helper task, they all use memory
from a single node for their kernel stack and task struct.
This patch suite creates kthread_create_on_node(), adding a 'cpu' parameter
to parameters already used by kthread_create().
This parameter serves in allocating memory for the new kthread on its
memory node if possible.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a node parameter to alloc_thread_info(), and change its name to
alloc_thread_info_node()
This change is needed to allow NUMA aware kthread_create_on_cpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All kthreads being created from a single helper task, they all use memory
from a single node for their kernel stack and task struct.
This patch suite creates kthread_create_on_cpu(), adding a 'cpu' parameter
to parameters already used by kthread_create().
This parameter serves in allocating memory for the new kthread on its
memory node if available.
Users of this new function are : ksoftirqd, kworker, migration, pktgend...
This patch:
Add a node parameter to alloc_task_struct(), and change its name to
alloc_task_struct_node()
This change is needed to allow NUMA aware kthread_create_on_cpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for creating a queuing context outside
of the queue itself. This enables us to batch up pieces of IO
before grabbing the block device queue lock and submitting them to
the IO scheduler.
The context is created on the stack of the process and assigned in
the task structure, so that we can auto-unplug it if we hit a schedule
event.
The current queue plugging happens implicitly if IO is submitted to
an empty device, yet callers have to remember to unplug that IO when
they are going to wait for it. This is an ugly API and has caused bugs
in the past. Additionally, it requires hacks in the vm (->sync_page()
callback) to handle that logic. By switching to an explicit plugging
scheme we make the API a lot nicer and can get rid of the ->sync_page()
hack in the vm.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Add khugepaged to relocate fragmented pages into hugepages if new
hugepages become available. (this is indipendent of the defrag logic that
will have to make new hugepages available)
The fundamental reason why khugepaged is unavoidable, is that some memory
can be fragmented and not everything can be relocated. So when a virtual
machine quits and releases gigabytes of hugepages, we want to use those
freely available hugepages to create huge-pmd in the other virtual
machines that may be running on fragmented memory, to maximize the CPU
efficiency at all times. The scan is slow, it takes nearly zero cpu time,
except when it copies data (in which case it means we definitely want to
pay for that cpu time) so it seems a good tradeoff.
In addition to the hugepages being released by other process releasing
memory, we have the strong suspicion that the performance impact of
potentially defragmenting hugepages during or before each page fault could
lead to more performance inconsistency than allocating small pages at
first and having them collapsed into large pages later... if they prove
themselfs to be long lived mappings (khugepaged scan is slow so short
lived mappings have low probability to run into khugepaged if compared to
long lived mappings).
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This increase the size of the mm struct a bit but it is needed to
preallocate one pte for each hugepage so that split_huge_page will not
require a fail path. Guarantee of success is a fundamental property of
split_huge_page to avoid decrasing swapping reliability and to avoid
adding -ENOMEM fail paths that would otherwise force the hugepage-unaware
VM code to learn rolling back in the middle of its pte mangling operations
(if something we need it to learn handling pmd_trans_huge natively rather
being capable of rollback). When split_huge_page runs a pte is needed to
succeed the split, to map the newly splitted regular pages with a regular
pte. This way all existing VM code remains backwards compatible by just
adding a split_huge_page* one liner. The memory waste of those
preallocated ptes is negligible and so it is worth it.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We'd like to be able to oom_score_adj a process up/down as it
enters/leaves the foreground. Currently, it is not possible to oom_adj
down without CAP_SYS_RESOURCE. This patch allows a task to decrease its
oom_score_adj back to the value that a CAP_SYS_RESOURCE thread set it to
or its inherited value at fork. Assuming the thread that has forked it
has oom_score_adj of 0, each process could decrease it back from 0 upon
activation unless a CAP_SYS_RESOURCE thread elevated it to something
higher.
Alternative considered:
* a setuid binary
* a daemon with CAP_SYS_RESOURCE
Since you don't wan't all processes to be able to reduce their oom_adj, a
setuid or daemon implementation would be complex. The alternatives also
have much higher overhead.
This patch updated from original patch based on feedback from David
Rientjes.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ying Han <yinghan@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This warning was added in commit bdff746a39 ("clone: prepare to recycle
CLONE_STOPPED") three years ago. 2.6.26 came and went. As far as I know,
no-one is actually using CLONE_STOPPED.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
gameport: use this_cpu_read instead of lookup
x86: udelay: Use this_cpu_read to avoid address calculation
x86: Use this_cpu_inc_return for nmi counter
x86: Replace uses of current_cpu_data with this_cpu ops
x86: Use this_cpu_ops to optimize code
vmstat: User per cpu atomics to avoid interrupt disable / enable
irq_work: Use per cpu atomics instead of regular atomics
cpuops: Use cmpxchg for xchg to avoid lock semantics
x86: this_cpu_cmpxchg and this_cpu_xchg operations
percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
percpu,x86: relocate this_cpu_add_return() and friends
connector: Use this_cpu operations
xen: Use this_cpu_inc_return
taskstats: Use this_cpu_ops
random: Use this_cpu_inc_return
fs: Use this_cpu_inc_return in buffer.c
highmem: Use this_cpu_xx_return() operations
vmstat: Use this_cpu_inc_return for vm statistics
x86: Support for this_cpu_add, sub, dec, inc_return
percpu: Generic support for this_cpu_add, sub, dec, inc_return
...
Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.
The cgroup exit mess also uncovered a struct autogroup reference leak.
copy_process() was simply freeing vs putting the signal_struct,
stranding a reference.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Oleg Nesterov <oleg@redhat.com>
LKML-Reference: <1293784350.6839.2.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
__get_cpu_var() can be replaced with this_cpu_read and will then use a
single read instruction with implied address calculation to access the
correct per cpu instance.
However, the address of a per cpu variable passed to __this_cpu_read()
cannot be determined (since it's an implied address conversion through
segment prefixes). Therefore apply this only to uses of __get_cpu_var
where the address of the variable is not used.
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hughd@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
idle_balance() drops/retakes rq->lock, leaving the previous task
vulnerable to set_tsk_need_resched(). Clear it after we return
from balancing instead, and in setup_thread_stack() as well, so
no successfully descheduled or never scheduled task has it set.
Need resched confused the skip_clock_update logic, which assumes
that the next call to update_rq_clock() will come nearly immediately
after being set. Make the optimization robust against the waking
a sleeper before it sucessfully deschedules case by checking that
the current task has not been dequeued before setting the flag,
since it is that useless clock update we're trying to save, and
clear unconditionally in schedule() proper instead of conditionally
in put_prev_task().
Signed-off-by: Mike Galbraith <efault@gmx.de>
Reported-by: Bjoern B. Brandenburg <bbb.lst@gmail.com>
Tested-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
LKML-Reference: <1291802742.1417.9.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A recurring complaint from CFS users is that parallel kbuild has
a negative impact on desktop interactivity. This patch
implements an idea from Linus, to automatically create task
groups. Currently, only per session autogroups are implemented,
but the patch leaves the way open for enhancement.
Implementation: each task's signal struct contains an inherited
pointer to a refcounted autogroup struct containing a task group
pointer, the default for all tasks pointing to the
init_task_group. When a task calls setsid(), a new task group
is created, the process is moved into the new task group, and a
reference to the preveious task group is dropped. Child
processes inherit this task group thereafter, and increase it's
refcount. When the last thread of a process exits, the
process's reference is dropped, such that when the last process
referencing an autogroup exits, the autogroup is destroyed.
At runqueue selection time, IFF a task has no cgroup assignment,
its current autogroup is used.
Autogroup bandwidth is controllable via setting it's nice level
through the proc filesystem:
cat /proc/<pid>/autogroup
Displays the task's group and the group's nice level.
echo <nice level> > /proc/<pid>/autogroup
Sets the task group's shares to the weight of nice <level> task.
Setting nice level is rate limited for !admin users due to the
abuse risk of task group locking.
The feature is enabled from boot by default if
CONFIG_SCHED_AUTOGROUP=y is selected, but can be disabled via
the boot option noautogroup, and can also be turned on/off on
the fly via:
echo [01] > /proc/sys/kernel/sched_autogroup_enabled
... which will automatically move tasks to/from the root task group.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Paul Turner <pjt@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
[ Removed the task_group_path() debug code, and fixed !EVENTFD build failure. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <1290281700.28711.9.camel@maggy.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Oleg Nesterov pointed out we have to prevent multiple-threads-inside-exec
itself and we can reuse ->cred_guard_mutex for it. Yes, concurrent
execve() has no worth.
Let's move ->cred_guard_mutex from task_struct to signal_struct. It
naturally prevent multiple-threads-inside-exec.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's pointless to kill a task if another thread sharing its mm cannot be
killed to allow future memory freeing. A subsequent patch will prevent
kills in such cases, but first it's necessary to have a way to flag a task
that shares memory with an OOM_DISABLE task that doesn't incur an
additional tasklist scan, which would make select_bad_process() an O(n^2)
function.
This patch adds an atomic counter to struct mm_struct that follows how
many threads attached to it have an oom_score_adj of OOM_SCORE_ADJ_MIN.
They cannot be killed by the kernel, so their memory cannot be freed in
oom conditions.
This only requires task_lock() on the task that we're operating on, it
does not require mm->mmap_sem since task_lock() pins the mm and the
operation is atomic.
[rientjes@google.com: changelog and sys_unshare() code]
[rientjes@google.com: protect oom_disable_count with task_lock in fork]
[rientjes@google.com: use old_mm for oom_disable_count in exec]
Signed-off-by: Ying Han <yinghan@google.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The below bug in fork led to the rmap walk finding the parent huge-pmd
twice instead of just once, because the anon_vma_chain objects of the
child vma still point to the vma->vm_mm of the parent.
The patch fixes it by making the rmap walk accurate during fork. It's not
a big deal normally but it worth being accurate considering the cost is
the same.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Johannes Weiner <jweiner@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's a really simple list, and several of the users want to go backwards
in it to find the previous vma. So rather than have to look up the
previous entry with 'find_vma_prev()' or something similar, just make it
doubly linked instead.
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fs: fs_struct rwlock to spinlock
struct fs_struct.lock is an rwlock with the read-side used to protect root and
pwd members while taking references to them. Taking a reference to a path
typically requires just 2 atomic ops, so the critical section is very small.
Parallel read-side operations would have cacheline contention on the lock, the
dentry, and the vfsmount cachelines, so the rwlock is unlikely to ever give a
real parallelism increase.
Replace it with a spinlock to avoid one or two atomic operations in typical
path lookup fastpath.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This a complete rewrite of the oom killer's badness() heuristic which is
used to determine which task to kill in oom conditions. The goal is to
make it as simple and predictable as possible so the results are better
understood and we end up killing the task which will lead to the most
memory freeing while still respecting the fine-tuning from userspace.
Instead of basing the heuristic on mm->total_vm for each task, the task's
rss and swap space is used instead. This is a better indication of the
amount of memory that will be freeable if the oom killed task is chosen
and subsequently exits. This helps specifically in cases where KDE or
GNOME is chosen for oom kill on desktop systems instead of a memory
hogging task.
The baseline for the heuristic is a proportion of memory that each task is
currently using in memory plus swap compared to the amount of "allowable"
memory. "Allowable," in this sense, means the system-wide resources for
unconstrained oom conditions, the set of mempolicy nodes, the mems
attached to current's cpuset, or a memory controller's limit. The
proportion is given on a scale of 0 (never kill) to 1000 (always kill),
roughly meaning that if a task has a badness() score of 500 that the task
consumes approximately 50% of allowable memory resident in RAM or in swap
space.
The proportion is always relative to the amount of "allowable" memory and
not the total amount of RAM systemwide so that mempolicies and cpusets may
operate in isolation; they shall not need to know the true size of the
machine on which they are running if they are bound to a specific set of
nodes or mems, respectively.
Root tasks are given 3% extra memory just like __vm_enough_memory()
provides in LSMs. In the event of two tasks consuming similar amounts of
memory, it is generally better to save root's task.
Because of the change in the badness() heuristic's baseline, it is also
necessary to introduce a new user interface to tune it. It's not possible
to redefine the meaning of /proc/pid/oom_adj with a new scale since the
ABI cannot be changed for backward compatability. Instead, a new tunable,
/proc/pid/oom_score_adj, is added that ranges from -1000 to +1000. It may
be used to polarize the heuristic such that certain tasks are never
considered for oom kill while others may always be considered. The value
is added directly into the badness() score so a value of -500, for
example, means to discount 50% of its memory consumption in comparison to
other tasks either on the system, bound to the mempolicy, in the cpuset,
or sharing the same memory controller.
/proc/pid/oom_adj is changed so that its meaning is rescaled into the
units used by /proc/pid/oom_score_adj, and vice versa. Changing one of
these per-task tunables will rescale the value of the other to an
equivalent meaning. Although /proc/pid/oom_adj was originally defined as
a bitshift on the badness score, it now shares the same linear growth as
/proc/pid/oom_score_adj but with different granularity. This is required
so the ABI is not broken with userspace applications and allows oom_adj to
be deprecated for future removal.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Concurrency managed workqueue needs to know when workers are going to
sleep and waking up. Using these two hooks, cmwq keeps track of the
current concurrency level and throttles execution of new works if it's
too high and wakes up another worker from the sleep hook if it becomes
too low.
This patch introduces PF_WQ_WORKER to identify workqueue workers and
adds the following two hooks.
* wq_worker_waking_up(): called when a worker is woken up.
* wq_worker_sleeping(): called when a worker is going to sleep and may
return a pointer to a local task which should be woken up. The
returned task is woken up using try_to_wake_up_local() which is
simplified ttwu which is called under rq lock and can only wake up
local tasks.
Both hooks are currently defined as noop in kernel/workqueue_sched.h.
Later cmwq implementation will replace them with proper
implementation.
These hooks are hard coded as they'll always be enabled.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Ingo Molnar <mingo@elte.hu>
This reverts commit 0ac0c0d0f8, which
caused cross-architecture build problems for all the wrong reasons.
IA64 already added its own version of __node_random(), but the fact is,
there is nothing architectural about the function, and the original
commit was just badly done. Revert it, since no fix is forthcoming.
Requested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
copy_process(pid => &init_struct_pid) doesn't do attach_pid/etc.
It shouldn't, but this means that the idle threads run with the wrong
pids copied from the caller's task_struct. In x86 case the caller is
either kernel_init() thread or keventd.
In particular, this means that after the series of cpu_up/cpu_down an
idle thread (which never exits) can run with .pid pointing to nowhere.
Change fork_idle() to initialize idle->pids[] correctly. We only set
.pid = &init_struct_pid but do not add .node to list, INIT_TASK() does
the same for the boot-cpu idle thread (swapper).
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Mathias Krause <Mathias.Krause@secunet.com>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional changes, just s/atomic_t count/int nr_threads/.
With the recent changes this counter has a single user, get_nr_threads()
And, none of its callers need the really accurate number of threads, not
to mention each caller obviously races with fork/exit. It is only used to
report this value to the user-space, except first_tid() uses it to avoid
the unnecessary while_each_thread() loop in the unlikely case.
It is a bit sad we need a word in struct signal_struct for this, perhaps
we can change get_nr_threads() to approximate the number of threads using
signal->live and kill ->nr_threads later.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
check_unshare_flags(CLONE_SIGHAND) adds CLONE_THREAD to *flags_ptr if the
task is multithreaded to ensure unshare_thread() will fail.
Not only this is a bit strange way to return the error, this is absolutely
meaningless. If signal->count > 1 then sighand->count must be also > 1,
and unshare_sighand() will fail anyway.
In fact, all CLONE_THREAD/SIGHAND/VM checks inside sys_unshare() do not
look right. Fortunately this code doesn't really work anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move taskstats_tgid_free() from __exit_signal() to free_signal_struct().
This way signal->stats never points to nowhere and we can read ->stats
lockless.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kill the empty thread_group_cputime_free() helper. It was needed to free
the per-cpu data which we no longer have.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a lot of problems with accessing task_struct->signal, it can
"disappear" at any moment. Even current can't use its ->signal safely
after exit_notify(). ->siglock helps, but it is not convenient, not
always possible, and sometimes it makes sense to use task->signal even
after this task has already dead.
This patch adds the reference counter, sigcnt, into signal_struct. This
reference is owned by task_struct and it is dropped in
__put_task_struct(). Perhaps it makes sense to export
get/put_signal_struct() later, but currently I don't see the immediate
reason.
Rename __cleanup_signal() to free_signal_struct() and unexport it. With
the previous changes it does nothing except kmem_cache_free().
Change __exit_signal() to not clear/free ->signal, it will be freed when
the last reference to any thread in the thread group goes away.
Note:
- when the last thead exits signal->tty can point to nowhere, see
the next patch.
- with or without this patch signal_struct->count should go away,
or at least it should be "int nr_threads" for fs/proc. This will
be addressed later.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tty_kref_put() has two callsites in copy_process() paths,
1. if copy_process() suceeds it is called before we copy
signal->tty from parent
2. otherwise it is called from __cleanup_signal() under
bad_fork_cleanup_signal: label
In both cases tty_kref_put() is not right and unneeded because we don't
have the balancing tty_kref_get(). Fortunately, this is harmless because
this can only happen without CLONE_THREAD, and in this case signal->tty
must be NULL.
Remove tty_kref_put() from copy_process() and __cleanup_signal(), and
change another caller of __cleanup_signal(), __exit_signal(), to call
tty_kref_put() by hand.
I hope this change makes sense by itself, but it is also needed to make
->signal refcountable.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some workloads that create a large number of small files tend to assign
too many pages to node 0 (multi-node systems). Part of the reason is that
the rotor (in cpuset_mem_spread_node()) used to assign nodes starts at
node 0 for newly created tasks.
This patch changes the rotor to be initialized to a random node number of
the cpuset.
[akpm@linux-foundation.org: fix layout]
[Lee.Schermerhorn@hp.com: Define stub numa_random() for !NUMA configuration]
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Paul Menage <menage@google.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (311 commits)
perf tools: Add mode to build without newt support
perf symbols: symbol inconsistency message should be done only at verbose=1
perf tui: Add explicit -lslang option
perf options: Type check all the remaining OPT_ variants
perf options: Type check OPT_BOOLEAN and fix the offenders
perf options: Check v type in OPT_U?INTEGER
perf options: Introduce OPT_UINTEGER
perf tui: Add workaround for slang < 2.1.4
perf record: Fix bug mismatch with -c option definition
perf options: Introduce OPT_U64
perf tui: Add help window to show key associations
perf tui: Make <- exit menus too
perf newt: Add single key shortcuts for zoom into DSO and threads
perf newt: Exit browser unconditionally when CTRL+C, q or Q is pressed
perf newt: Fix the 'A'/'a' shortcut for annotate
perf newt: Make <- exit the ui_browser
x86, perf: P4 PMU - fix counters management logic
perf newt: Make <- zoom out filters
perf report: Report number of events, not samples
perf hist: Clarify events_stats fields usage
...
Fix up trivial conflicts in kernel/fork.c and tools/perf/builtin-record.c
Originally, commit d899bf7b ("procfs: provide stack information for
threads") attempted to introduce a new feature for showing where the
threadstack was located and how many pages are being utilized by the
stack.
Commit c44972f1 ("procfs: disable per-task stack usage on NOMMU") was
applied to fix the NO_MMU case.
Commit 89240ba0 ("x86, fs: Fix x86 procfs stack information for threads on
64-bit") was applied to fix a bug in ia32 executables being loaded.
Commit 9ebd4eba7 ("procfs: fix /proc/<pid>/stat stack pointer for kernel
threads") was applied to fix a bug which had kernel threads printing a
userland stack address.
Commit 1306d603f ('proc: partially revert "procfs: provide stack
information for threads"') was then applied to revert the stack pages
being used to solve a significant performance regression.
This patch nearly undoes the effect of all these patches.
The reason for reverting these is it provides an unusable value in
field 28. For x86_64, a fork will result in the task->stack_start
value being updated to the current user top of stack and not the stack
start address. This unpredictability of the stack_start value makes
it worthless. That includes the intended use of showing how much stack
space a thread has.
Other architectures will get different values. As an example, ia64
gets 0. The do_fork() and copy_process() functions appear to treat the
stack_start and stack_size parameters as architecture specific.
I only partially reverted c44972f1 ("procfs: disable per-task stack usage
on NOMMU") . If I had completely reverted it, I would have had to change
mm/Makefile only build pagewalk.o when CONFIG_PROC_PAGE_MONITOR is
configured. Since I could not test the builds without significant effort,
I decided to not change mm/Makefile.
I only partially reverted 89240ba0 ("x86, fs: Fix x86 procfs stack
information for threads on 64-bit") . I left the KSTK_ESP() change in
place as that seemed worthwhile.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Stefani Seibold <stefani@seibold.net>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- We weren't zeroing p->rss_stat[] at fork()
- Consequently sync_mm_rss() was dereferencing tsk->mm for kernel
threads and was oopsing.
- Make __sync_task_rss_stat() static, too.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15648
[akpm@linux-foundation.org: remove the BUG_ON(!mm->rss)]
Reported-by: Troels Liebe Bentsen <tlb@rapanden.dk>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
"Michael S. Tsirkin" <mst@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support for the PMU's BTS features has been upstreamed in
v2.6.32, but we still have the old and disabled ptrace-BTS,
as Linus noticed it not so long ago.
It's buggy: TIF_DEBUGCTLMSR is trampling all over that MSR without
regard for other uses (perf) and doesn't provide the flexibility
needed for perf either.
Its users are ptrace-block-step and ptrace-bts, since ptrace-bts
was never used and ptrace-block-step can be implemented using a
much simpler approach.
So axe all 3000 lines of it. That includes the *locked_memory*()
APIs in mm/mlock.c as well.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Markus Metzger <markus.t.metzger@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <20100325135413.938004390@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
locking: Make sparse work with inline spinlocks and rwlocks
x86/mce: Fix RCU lockdep splats
rcu: Increase RCU CPU stall timeouts if PROVE_RCU
ftrace: Replace read_barrier_depends() with rcu_dereference_raw()
rcu: Suppress RCU lockdep warnings during early boot
rcu, ftrace: Fix RCU lockdep splat in ftrace_perf_buf_prepare()
rcu: Suppress __mpol_dup() false positive from RCU lockdep
rcu: Make rcu_read_lock_sched_held() handle !PREEMPT
rcu: Add control variables to lockdep_rcu_dereference() diagnostics
rcu, cgroup: Relax the check in task_subsys_state() as early boot is now handled by lockdep-RCU
rcu: Use wrapper function instead of exporting tasklist_lock
sched, rcu: Fix rcu_dereference() for RCU-lockdep
rcu: Make task_subsys_state() RCU-lockdep checks handle boot-time use
rcu: Fix holdoff for accelerated GPs for last non-dynticked CPU
x86/gart: Unexport gart_iommu_aperture
Fix trivial conflicts in kernel/trace/ftrace.c
Remove unneeded initializations in thread_group_cputime_init() and in
posix_cpu_timers_init_group(). They are useless after kmem_cache_zalloc()
was used in copy_signal().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kmem_cache_zalloc() on signal creation and remove unneeded
initialization lines in copy_signal().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure compiler won't do weird things with limits. E.g. fetching them
twice may return 2 different values after writable limits are implemented.
I.e. either use rlimit helpers added in commit 3e10e716ab ("resource:
add helpers for fetching rlimits") or ACCESS_ONCE if not applicable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old anon_vma code can lead to scalability issues with heavily forking
workloads. Specifically, each anon_vma will be shared between the parent
process and all its child processes.
In a workload with 1000 child processes and a VMA with 1000 anonymous
pages per process that get COWed, this leads to a system with a million
anonymous pages in the same anon_vma, each of which is mapped in just one
of the 1000 processes. However, the current rmap code needs to walk them
all, leading to O(N) scanning complexity for each page.
This can result in systems where one CPU is walking the page tables of
1000 processes in page_referenced_one, while all other CPUs are stuck on
the anon_vma lock. This leads to catastrophic failure for a benchmark
like AIM7, where the total number of processes can reach in the tens of
thousands. Real workloads are still a factor 10 less process intensive
than AIM7, but they are catching up.
This patch changes the way anon_vmas and VMAs are linked, which allows us
to associate multiple anon_vmas with a VMA. At fork time, each child
process gets its own anon_vmas, in which its COWed pages will be
instantiated. The parents' anon_vma is also linked to the VMA, because
non-COWed pages could be present in any of the children.
This reduces rmap scanning complexity to O(1) for the pages of the 1000
child processes, with O(N) complexity for at most 1/N pages in the system.
This reduces the average scanning cost in heavily forking workloads from
O(N) to 2.
The only real complexity in this patch stems from the fact that linking a
VMA to anon_vmas now involves memory allocations. This means vma_adjust
can fail, if it needs to attach a VMA to anon_vma structures. This in
turn means error handling needs to be added to the calling functions.
A second source of complexity is that, because there can be multiple
anon_vmas, the anon_vma linking in vma_adjust can no longer be done under
"the" anon_vma lock. To prevent the rmap code from walking up an
incomplete VMA, this patch introduces the VM_LOCK_RMAP VMA flag. This bit
flag uses the same slot as the NOMMU VM_MAPPED_COPY, with an ifdef in mm.h
to make sure it is impossible to compile a kernel that needs both symbolic
values for the same bitflag.
Some test results:
Without the anon_vma changes, when AIM7 hits around 9.7k users (on a test
box with 16GB RAM and not quite enough IO), the system ends up running
>99% in system time, with every CPU on the same anon_vma lock in the
pageout code.
With these changes, AIM7 hits the cross-over point around 29.7k users.
This happens with ~99% IO wait time, there never seems to be any spike in
system time. The anon_vma lock contention appears to be resolved.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently, per-mm statistics counter is defined by macro in sched.h
This patch modifies it to
- defined in mm.h as inlinf functions
- use array instead of macro's name creation.
This patch is for reducing patch size in future patch to modify
implementation of per-mm counter.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a number of issues:
1) TASK_WAKING vs cgroup_clone (cpusets)
copy_process():
sched_fork()
child->state = TASK_WAKING; /* waiting for wake_up_new_task() */
if (current->nsproxy != p->nsproxy)
ns_cgroup_clone()
cgroup_clone()
mutex_lock(inode->i_mutex)
mutex_lock(cgroup_mutex)
cgroup_attach_task()
ss->can_attach()
ss->attach() [ -> cpuset_attach() ]
cpuset_attach_task()
set_cpus_allowed_ptr();
while (child->state == TASK_WAKING)
cpu_relax();
will deadlock the system.
2) cgroup_clone (cpusets) vs copy_process
So even if the above would work we still have:
copy_process():
if (current->nsproxy != p->nsproxy)
ns_cgroup_clone()
cgroup_clone()
mutex_lock(inode->i_mutex)
mutex_lock(cgroup_mutex)
cgroup_attach_task()
ss->can_attach()
ss->attach() [ -> cpuset_attach() ]
cpuset_attach_task()
set_cpus_allowed_ptr();
...
p->cpus_allowed = current->cpus_allowed
over-writing the modified cpus_allowed.
3) fork() vs hotplug
if we unplug the child's cpu after the sanity check when the child
gets attached to the task_list but before wake_up_new_task() shit
will meet with fan.
Solve all these issues by moving fork cpu selection into
wake_up_new_task().
Reported-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1264106190.4283.1314.camel@laptop>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thanks to Roland who pointed out de_thread() issues.
Currently we add sub-threads to ->real_parent->children list. This buys
nothing but slows down do_wait().
With this patch ->children contains only main threads (group leaders).
The only complication is that forget_original_parent() should iterate over
sub-threads by hand, and de_thread() needs another list_replace() when it
changes ->group_leader.
Henceforth do_wait_thread() can never see task_detached() && !EXIT_DEAD
tasks, we can remove this check (and we can unify do_wait_thread() and
ptrace_do_wait()).
This change can confuse the optimistic search in mm_update_next_owner(),
but this is fixable and minor.
Perhaps badness() and oom_kill_process() should be updated, but they
should be fixed in any case.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ratan Nalumasu <rnalumasu@gmail.com>
Cc: Vitaly Mayatskikh <vmayatsk@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the tracee calls fork() after PTRACE_SINGLESTEP, the forked child
starts with TIF_SINGLESTEP/X86_EFLAGS_TF bits copied from ptraced parent.
This is not right, especially when the new child is not auto-attaced: in
this case it is killed by SIGTRAP.
Change copy_process() to call user_disable_single_step(). Tested on x86.
Test-case:
#include <stdio.h>
#include <unistd.h>
#include <signal.h>
#include <sys/ptrace.h>
#include <sys/wait.h>
#include <assert.h>
int main(void)
{
int pid, status;
if (!(pid = fork())) {
assert(ptrace(PTRACE_TRACEME) == 0);
kill(getpid(), SIGSTOP);
if (!fork()) {
/* kernel bug: this child will be killed by SIGTRAP */
printf("Hello world\n");
return 43;
}
wait(&status);
return WEXITSTATUS(status);
}
for (;;) {
assert(pid == wait(&status));
if (WIFEXITED(status))
break;
assert(ptrace(PTRACE_SINGLESTEP, pid, 0,0) == 0);
}
assert(WEXITSTATUS(status) == 43);
return 0;
}
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In massive parallel enviroment, res_counter can be a performance
bottleneck. One strong techinque to reduce lock contention is reducing
calls by coalescing some amount of calls into one.
Considering charge/uncharge chatacteristic,
- charge is done one by one via demand-paging.
- uncharge is done by
- in chunk at munmap, truncate, exit, execve...
- one by one via vmscan/paging.
It seems we have a chance to coalesce uncharges for improving scalability
at unmap/truncation.
This patch is a for coalescing uncharge. For avoiding scattering memcg's
structure to functions under /mm, this patch adds memcg batch uncharge
information to the task. A reason for per-task batching is for making use
of caller's context information. We do batched uncharge (deleyed
uncharge) when truncation/unmap occurs but do direct uncharge when
uncharge is called by memory reclaim (vmscan.c).
The degree of coalescing depends on callers
- at invalidate/trucate... pagevec size
- at unmap ....ZAP_BLOCK_SIZE
(memory itself will be freed in this degree.)
Then, we'll not coalescing too much.
On x86-64 8cpu server, I tested overheads of memcg at page fault by
running a program which does map/fault/unmap in a loop. Running
a task per a cpu by taskset and see sum of the number of page faults
in 60secs.
[without memcg config]
40156968 page-faults # 0.085 M/sec ( +- 0.046% )
27.67 cache-miss/faults
[root cgroup]
36659599 page-faults # 0.077 M/sec ( +- 0.247% )
31.58 miss/faults
[in a child cgroup]
18444157 page-faults # 0.039 M/sec ( +- 0.133% )
69.96 miss/faults
[child with this patch]
27133719 page-faults # 0.057 M/sec ( +- 0.155% )
47.16 miss/faults
We can see some amounts of improvement.
(root cgroup doesn't affected by this patch)
Another patch for "charge" will follow this and above will be improved more.
Changelog(since 2009/10/02):
- renamed filed of memcg_batch (as pages to bytes, memsw to memsw_bytes)
- some clean up and commentary/description updates.
- added initialize code to copy_process(). (possible bug fix)
Changelog(old):
- fixed !CONFIG_MEM_CGROUP case.
- rebased onto the latest mmotm + softlimit fix patches.
- unified patch for callers
- added commetns.
- make ->do_batch as bool.
- removed css_get() at el. We don't need it.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (84 commits)
KVM: VMX: Fix comparison of guest efer with stale host value
KVM: s390: Fix prefix register checking in arch/s390/kvm/sigp.c
KVM: Drop user return notifier when disabling virtualization on a cpu
KVM: VMX: Disable unrestricted guest when EPT disabled
KVM: x86 emulator: limit instructions to 15 bytes
KVM: s390: Make psw available on all exits, not just a subset
KVM: x86: Add KVM_GET/SET_VCPU_EVENTS
KVM: VMX: Report unexpected simultaneous exceptions as internal errors
KVM: Allow internal errors reported to userspace to carry extra data
KVM: Reorder IOCTLs in main kvm.h
KVM: x86: Polish exception injection via KVM_SET_GUEST_DEBUG
KVM: only clear irq_source_id if irqchip is present
KVM: x86: disallow KVM_{SET,GET}_LAPIC without allocated in-kernel lapic
KVM: x86: disallow multiple KVM_CREATE_IRQCHIP
KVM: VMX: Remove vmx->msr_offset_efer
KVM: MMU: update invlpg handler comment
KVM: VMX: move CR3/PDPTR update to vmx_set_cr3
KVM: remove duplicated task_switch check
KVM: powerpc: Fix BUILD_BUG_ON condition
KVM: VMX: Use shared msr infrastructure
...
Trivial conflicts due to new Kconfig options in arch/Kconfig and kernel/Makefile
With CLONE_IO, parent's io_context->nr_tasks is incremented, but never
decremented whenever copy_process() fails afterwards, which prevents
exit_io_context() from calling IO schedulers exit functions.
Give a task_struct to exit_io_context(), and call exit_io_context() instead of
put_io_context() in copy_process() cleanup path.
Signed-off-by: Louis Rilling <louis.rilling@kerlabs.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This is a real fix for problem of utime/stime values decreasing
described in the thread:
http://lkml.org/lkml/2009/11/3/522
Now cputime is accounted in the following way:
- {u,s}time in task_struct are increased every time when the thread
is interrupted by a tick (timer interrupt).
- When a thread exits, its {u,s}time are added to signal->{u,s}time,
after adjusted by task_times().
- When all threads in a thread_group exits, accumulated {u,s}time
(and also c{u,s}time) in signal struct are added to c{u,s}time
in signal struct of the group's parent.
So {u,s}time in task struct are "raw" tick count, while
{u,s}time and c{u,s}time in signal struct are "adjusted" values.
And accounted values are used by:
- task_times(), to get cputime of a thread:
This function returns adjusted values that originates from raw
{u,s}time and scaled by sum_exec_runtime that accounted by CFS.
- thread_group_cputime(), to get cputime of a thread group:
This function returns sum of all {u,s}time of living threads in
the group, plus {u,s}time in the signal struct that is sum of
adjusted cputimes of all exited threads belonged to the group.
The problem is the return value of thread_group_cputime(),
because it is mixed sum of "raw" value and "adjusted" value:
group's {u,s}time = foreach(thread){{u,s}time} + exited({u,s}time)
This misbehavior can break {u,s}time monotonicity.
Assume that if there is a thread that have raw values greater
than adjusted values (e.g. interrupted by 1000Hz ticks 50 times
but only runs 45ms) and if it exits, cputime will decrease (e.g.
-5ms).
To fix this, we could do:
group's {u,s}time = foreach(t){task_times(t)} + exited({u,s}time)
But task_times() contains hard divisions, so applying it for
every thread should be avoided.
This patch fixes the above problem in the following way:
- Modify thread's exit (= __exit_signal()) not to use task_times().
It means {u,s}time in signal struct accumulates raw values instead
of adjusted values. As the result it makes thread_group_cputime()
to return pure sum of "raw" values.
- Introduce a new function thread_group_times(*task, *utime, *stime)
that converts "raw" values of thread_group_cputime() to "adjusted"
values, in same calculation procedure as task_times().
- Modify group's exit (= wait_task_zombie()) to use this introduced
thread_group_times(). It make c{u,s}time in signal struct to
have adjusted values like before this patch.
- Replace some thread_group_cputime() by thread_group_times().
This replacements are only applied where conveys the "adjusted"
cputime to users, and where already uses task_times() near by it.
(i.e. sys_times(), getrusage(), and /proc/<PID>/stat.)
This patch have a positive side effect:
- Before this patch, if a group contains many short-life threads
(e.g. runs 0.9ms and not interrupted by ticks), the group's
cputime could be invisible since thread's cputime was accumulated
after adjusted: imagine adjustment function as adj(ticks, runtime),
{adj(0, 0.9) + adj(0, 0.9) + ....} = {0 + 0 + ....} = 0.
After this patch it will not happen because the adjustment is
applied after accumulated.
v2:
- remove if()s, put new variables into signal_struct.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Spencer Candland <spencer@bluehost.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
LKML-Reference: <4B162517.8040909@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- Remove if({u,s}t)s because no one call it with NULL now.
- Use cputime_{add,sub}().
- Add ifndef-endif for prev_{u,s}time since they are used
only when !VIRT_CPU_ACCOUNTING.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Spencer Candland <spencer@bluehost.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
LKML-Reference: <4B1624C7.7040302@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fork() clones all thread_info flags, including
TIF_USER_RETURN_NOTIFY; if the new task is first scheduled on a cpu
which doesn't have user return notifiers set, this causes user
return notifiers to trigger without any way of clearing itself.
This is easy to trigger with a forky workload on the host in
parallel with kvm, resulting in a cpu in an endless loop on the
verge of returning to userspace.
Fix by dropping the TIF_USER_RETURN_NOTIFY immediately after fork.
Signed-off-by: Avi Kivity <avi@redhat.com>
LKML-Reference: <1259505288-16559-1-git-send-email-avi@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
nr_processes() returns the sum of the per cpu counter process_counts for
all online CPUs. This counter is incremented for the current CPU on
fork() and decremented for the current CPU on exit(). Since a process
does not necessarily fork and exit on the same CPU the process_count for
an individual CPU can be either positive or negative and effectively has
no meaning in isolation.
Therefore calculating the sum of process_counts over only the online
CPUs omits the processes which were started or stopped on any CPU which
has since been unplugged. Only the sum of process_counts across all
possible CPUs has meaning.
The only caller of nr_processes() is proc_root_getattr() which
calculates the number of links to /proc as
stat->nlink = proc_root.nlink + nr_processes();
You don't have to be all that unlucky for the nr_processes() to return a
negative value leading to a negative number of links (or rather, an
apparently enormous number of links). If this happens then you can get
failures where things like "ls /proc" start to fail because they got an
-EOVERFLOW from some stat() call.
Example with some debugging inserted to show what goes on:
# ps haux|wc -l
nr_processes: CPU0: 90
nr_processes: CPU1: 1030
nr_processes: CPU2: -900
nr_processes: CPU3: -136
nr_processes: TOTAL: 84
proc_root_getattr. nlink 12 + nr_processes() 84 = 96
84
# echo 0 >/sys/devices/system/cpu/cpu1/online
# ps haux|wc -l
nr_processes: CPU0: 85
nr_processes: CPU2: -901
nr_processes: CPU3: -137
nr_processes: TOTAL: -953
proc_root_getattr. nlink 12 + nr_processes() -953 = -941
75
# stat /proc/
nr_processes: CPU0: 84
nr_processes: CPU2: -901
nr_processes: CPU3: -137
nr_processes: TOTAL: -954
proc_root_getattr. nlink 12 + nr_processes() -954 = -942
File: `/proc/'
Size: 0 Blocks: 0 IO Block: 1024 directory
Device: 3h/3d Inode: 1 Links: 4294966354
Access: (0555/dr-xr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2009-11-03 09:06:55.000000000 +0000
Modify: 2009-11-03 09:06:55.000000000 +0000
Change: 2009-11-03 09:06:55.000000000 +0000
I'm not 100% convinced that the per_cpu regions remain valid for offline
CPUs, although my testing suggests that they do. If not then I think the
correct solution would be to aggregate the process_count for a given CPU
into a global base value in cpu_down().
This bug appears to pre-date the transition to git and it looks like it
may even have been present in linux-2.6.0-test7-bk3 since it looks like
the code Rusty patched in http://lwn.net/Articles/64773/ was already
wrong.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: fix requeue_pi key imbalance
futex: Fix typo in FUTEX_WAIT/WAKE_BITSET_PRIVATE definitions
rcu: Place root rcu_node structure in separate lockdep class
rcu: Make hot-unplugged CPU relinquish its own RCU callbacks
rcu: Move rcu_barrier() to rcutree
futex: Move exit_pi_state() call to release_mm()
futex: Nullify robust lists after cleanup
futex: Fix locking imbalance
panic: Fix panic message visibility by calling bust_spinlocks(0) before dying
rcu: Replace the rcu_barrier enum with pointer to call_rcu*() function
rcu: Clean up code based on review feedback from Josh Triplett, part 4
rcu: Clean up code based on review feedback from Josh Triplett, part 3
rcu: Fix rcu_lock_map build failure on CONFIG_PROVE_LOCKING=y
rcu: Clean up code to address Ingo's checkpatch feedback
rcu: Clean up code based on review feedback from Josh Triplett, part 2
rcu: Clean up code based on review feedback from Josh Triplett
exit_pi_state() is called from do_exit() but not from do_execve().
Move it to release_mm() so it gets called from do_execve() as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: stable@kernel.org
Cc: Anirban Sinha <ani@anirban.org>
Cc: Peter Zijlstra <peterz@infradead.org>
The robust list pointers of user space held futexes are kept intact
over an exec() call. When the exec'ed task exits exit_robust_list() is
called with the stale pointer. The risk of corruption is minimal, but
still it is incorrect to keep the pointers valid. Actually glibc
should uninstall the robust list before calling exec() but we have to
deal with it anyway.
Nullify the pointers after [compat_]exit_robust_list() has been
called.
Reported-by: Anirban Sinha <ani@anirban.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: stable@kernel.org
Because the binfmt is not different between threads in the same process,
it can be moved from task_struct to mm_struct. And binfmt moudle is
handled per mm_struct instead of task_struct.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
->ioctx_lock and ->ioctx_list are used only under CONFIG_AIO.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When global or container-init processes use CLONE_PARENT, they create a
multi-rooted process tree. Besides siblings of global init remain as
zombies on exit since they are not reaped by their parent (swapper). So
prevent global and container-inits from creating siblings.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Oren Laadan <orenl@cs.columbia.edu>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A patch to give a better overview of the userland application stack usage,
especially for embedded linux.
Currently you are only able to dump the main process/thread stack usage
which is showed in /proc/pid/status by the "VmStk" Value. But you get no
information about the consumed stack memory of the the threads.
There is an enhancement in the /proc/<pid>/{task/*,}/*maps and which marks
the vm mapping where the thread stack pointer reside with "[thread stack
xxxxxxxx]". xxxxxxxx is the maximum size of stack. This is a value
information, because libpthread doesn't set the start of the stack to the
top of the mapped area, depending of the pthread usage.
A sample output of /proc/<pid>/task/<tid>/maps looks like:
08048000-08049000 r-xp 00000000 03:00 8312 /opt/z
08049000-0804a000 rw-p 00001000 03:00 8312 /opt/z
0804a000-0806b000 rw-p 00000000 00:00 0 [heap]
a7d12000-a7d13000 ---p 00000000 00:00 0
a7d13000-a7f13000 rw-p 00000000 00:00 0 [thread stack: 001ff4b4]
a7f13000-a7f14000 ---p 00000000 00:00 0
a7f14000-a7f36000 rw-p 00000000 00:00 0
a7f36000-a8069000 r-xp 00000000 03:00 4222 /lib/libc.so.6
a8069000-a806b000 r--p 00133000 03:00 4222 /lib/libc.so.6
a806b000-a806c000 rw-p 00135000 03:00 4222 /lib/libc.so.6
a806c000-a806f000 rw-p 00000000 00:00 0
a806f000-a8083000 r-xp 00000000 03:00 14462 /lib/libpthread.so.0
a8083000-a8084000 r--p 00013000 03:00 14462 /lib/libpthread.so.0
a8084000-a8085000 rw-p 00014000 03:00 14462 /lib/libpthread.so.0
a8085000-a8088000 rw-p 00000000 00:00 0
a8088000-a80a4000 r-xp 00000000 03:00 8317 /lib/ld-linux.so.2
a80a4000-a80a5000 r--p 0001b000 03:00 8317 /lib/ld-linux.so.2
a80a5000-a80a6000 rw-p 0001c000 03:00 8317 /lib/ld-linux.so.2
afaf5000-afb0a000 rw-p 00000000 00:00 0 [stack]
ffffe000-fffff000 r-xp 00000000 00:00 0 [vdso]
Also there is a new entry "stack usage" in /proc/<pid>/{task/*,}/status
which will you give the current stack usage in kb.
A sample output of /proc/self/status looks like:
Name: cat
State: R (running)
Tgid: 507
Pid: 507
.
.
.
CapBnd: fffffffffffffeff
voluntary_ctxt_switches: 0
nonvoluntary_ctxt_switches: 0
Stack usage: 12 kB
I also fixed stack base address in /proc/<pid>/{task/*,}/stat to the base
address of the associated thread stack and not the one of the main
process. This makes more sense.
[akpm@linux-foundation.org: fs/proc/array.c now needs walk_page_range()]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, OOM logic callflow is here.
__out_of_memory()
select_bad_process() for each task
badness() calculate badness of one task
oom_kill_process() search child
oom_kill_task() kill target task and mm shared tasks with it
example, process-A have two thread, thread-A and thread-B and it have very
fat memory and each thread have following oom_adj and oom_score.
thread-A: oom_adj = OOM_DISABLE, oom_score = 0
thread-B: oom_adj = 0, oom_score = very-high
Then, select_bad_process() select thread-B, but oom_kill_task() refuse
kill the task because thread-A have OOM_DISABLE. Thus __out_of_memory()
call select_bad_process() again. but select_bad_process() select the same
task. It mean kernel fall in livelock.
The fact is, select_bad_process() must select killable task. otherwise
OOM logic go into livelock.
And root cause is, oom_adj shouldn't be per-thread value. it should be
per-process value because OOM-killer kill a process, not thread. Thus
This patch moves oomkilladj (now more appropriately named oom_adj) from
struct task_struct to struct signal_struct. it naturally prevent
select_bad_process() choose wrong task.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rawhide users have reported hang at startup when cryptsetup is run: the
same problem can be simply reproduced by running a program int main() {
mlockall(MCL_CURRENT | MCL_FUTURE); return 0; }
The problem is that exit_mmap() applies munlock_vma_pages_all() to
clean up VM_LOCKED areas, and its current implementation (stupidly)
tries to fault in absent pages, for example where PROT_NONE prevented
them being faulted in when mlocking. Whereas the "ksm: fix oom
deadlock" patch, knowing there's a race by which KSM might try to fault
in pages after exit_mmap() had finally zapped the range, backs out of
such faults doing nothing when its ksm_test_exit() notices mm_users 0.
So revert that part of "ksm: fix oom deadlock" which moved the
ksm_exit() call from before exit_mmap() to the middle of exit_mmap();
and remove those ksm_test_exit() checks from the page fault paths, so
allowing the munlocking to proceed without interference.
ksm_exit, if there are rmap_items still chained on this mm slot, takes
mmap_sem write side: so preventing KSM from working on an mm while
exit_mmap runs. And KSM will bail out as soon as it notices that
mm_users is already zero, thanks to its internal ksm_test_exit checks.
So that when a task is killed by OOM killer or the user, KSM will not
indefinitely prevent it from running exit_mmap to release its memory.
This does break a part of what "ksm: fix oom deadlock" was trying to
achieve. When unmerging KSM (echo 2 >/sys/kernel/mm/ksm), and even
when ksmd itself has to cancel a KSM page, it is possible that the
first OOM-kill victim would be the KSM process being faulted: then its
memory won't be freed until a second victim has been selected (freeing
memory for the unmerging fault to complete).
But the OOM killer is already liable to kill a second victim once the
intended victim's p->mm goes to NULL: so there's not much point in
rejecting this KSM patch before fixing that OOM behaviour. It is very
much more important to allow KSM users to boot up, than to haggle over
an unlikely and poorly supported OOM case.
We also intend to fix munlocking to not fault pages: at which point
this patch _could_ be reverted; though that would be controversial, so
we hope to find a better solution.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Justin M. Forbes <jforbes@redhat.com>
Acked-for-now-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's a now-obvious deadlock in KSM's out-of-memory handling:
imagine ksmd or KSM_RUN_UNMERGE handling, holding ksm_thread_mutex,
trying to allocate a page to break KSM in an mm which becomes the
OOM victim (quite likely in the unmerge case): it's killed and goes
to exit, and hangs there waiting to acquire ksm_thread_mutex.
Clearly we must not require ksm_thread_mutex in __ksm_exit, simple
though that made everything else: perhaps use mmap_sem somehow?
And part of the answer lies in the comments on unmerge_ksm_pages:
__ksm_exit should also leave all the rmap_item removal to ksmd.
But there's a fundamental problem, that KSM relies upon mmap_sem to
guarantee the consistency of the mm it's dealing with, yet exit_mmap
tears down an mm without taking mmap_sem. And bumping mm_users won't
help at all, that just ensures that the pages the OOM killer assumes
are on their way to being freed will not be freed.
The best answer seems to be, to move the ksm_exit callout from just
before exit_mmap, to the middle of exit_mmap: after the mm's pages
have been freed (if the mmu_gather is flushed), but before its page
tables and vma structures have been freed; and down_write,up_write
mmap_sem there to serialize with KSM's own reliance on mmap_sem.
But KSM then needs to be careful, whenever it downs mmap_sem, to
check that the mm is not already exiting: there's a danger of using
find_vma on a layout that's being torn apart, or writing into page
tables which have been freed for reuse; and even do_anonymous_page
and __do_fault need to check they're not being called by break_ksm
to reinstate a pte after zap_pte_range has zapped that page table.
Though it might be clearer to add an exiting flag, set while holding
mmap_sem in __ksm_exit, that wouldn't cover the issue of reinstating
a zapped pte. All we need is to check whether mm_users is 0 - but
must remember that ksmd may detect that before __ksm_exit is reached.
So, ksm_test_exit(mm) added to comment such checks on mm->mm_users.
__ksm_exit now has to leave clearing up the rmap_items to ksmd,
that needs ksm_thread_mutex; but shift the exiting mm just after the
ksm_scan cursor so that it will soon be dealt with. __ksm_enter raise
mm_count to hold the mm_struct, ksmd's exit processing (exactly like
its processing when it finds all VM_MERGEABLEs unmapped) mmdrop it,
similar procedure for KSM_RUN_UNMERGE (which has stopped ksmd).
But also give __ksm_exit a fast path: when there's no complication
(no rmap_items attached to mm and it's not at the ksm_scan cursor),
it can safely do all the exiting work itself. This is not just an
optimization: when ksmd is not running, the raised mm_count would
otherwise leak mm_structs.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: Izik Eidus <ieidus@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch presents the mm interface to a dummy version of ksm.c, for
better scrutiny of that interface: the real ksm.c follows later.
When CONFIG_KSM is not set, madvise(2) reject MADV_MERGEABLE and
MADV_UNMERGEABLE with EINVAL, since that seems more helpful than
pretending that they can be serviced. But when CONFIG_KSM=y, accept them
even if KSM is not currently running, and even on areas which KSM will not
touch (e.g. hugetlb or shared file or special driver mappings).
Like other madvices, report ENOMEM despite success if any area in the
range is unmapped, and use EAGAIN to report out of memory.
Define vma flag VM_MERGEABLE to identify an area on which KSM may try
merging pages: leave it to ksm_madvise() to decide whether to set it.
Define mm flag MMF_VM_MERGEABLE to identify an mm which might contain
VM_MERGEABLE areas, to minimize callouts when forking or exiting.
Based upon earlier patches by Chris Wright and Izik Eidus.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The amount of memory allocated to kernel stacks can become significant and
cause OOM conditions. However, we do not display the amount of memory
consumed by stacks.
Add code to display the amount of memory used for stacks in /proc/meminfo.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (28 commits)
rcu: Move end of special early-boot RCU operation earlier
rcu: Changes from reviews: avoid casts, fix/add warnings, improve comments
rcu: Create rcutree plugins to handle hotplug CPU for multi-level trees
rcu: Remove lockdep annotations from RCU's _notrace() API members
rcu: Add #ifdef to suppress __rcu_offline_cpu() warning in !HOTPLUG_CPU builds
rcu: Add CPU-offline processing for single-node configurations
rcu: Add "notrace" to RCU function headers used by ftrace
rcu: Remove CONFIG_PREEMPT_RCU
rcu: Merge preemptable-RCU functionality into hierarchical RCU
rcu: Simplify rcu_pending()/rcu_check_callbacks() API
rcu: Use debugfs_remove_recursive() simplify code.
rcu: Merge per-RCU-flavor initialization into pre-existing macro
rcu: Fix online/offline indication for rcudata.csv trace file
rcu: Consolidate sparse and lockdep declarations in include/linux/rcupdate.h
rcu: Renamings to increase RCU clarity
rcu: Move private definitions from include/linux/rcutree.h to kernel/rcutree.h
rcu: Expunge lingering references to CONFIG_CLASSIC_RCU, optimize on !SMP
rcu: Delay rcu_barrier() wait until beginning of next CPU-hotunplug operation.
rcu: Fix typo in rcu_irq_exit() comment header
rcu: Make rcupreempt_trace.c look at offline CPUs
...
Add a config option (CONFIG_DEBUG_CREDENTIALS) to turn on some debug checking
for credential management. The additional code keeps track of the number of
pointers from task_structs to any given cred struct, and checks to see that
this number never exceeds the usage count of the cred struct (which includes
all references, not just those from task_structs).
Furthermore, if SELinux is enabled, the code also checks that the security
pointer in the cred struct is never seen to be invalid.
This attempts to catch the bug whereby inode_has_perm() faults in an nfsd
kernel thread on seeing cred->security be a NULL pointer (it appears that the
credential struct has been previously released):
http://www.kerneloops.org/oops.php?number=252883
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Spotted by Hiroshi Shimamoto who also provided the test-case below.
copy_process() uses signal->count as a reference counter, but it is not.
This test case
#include <sys/types.h>
#include <sys/wait.h>
#include <unistd.h>
#include <stdio.h>
#include <errno.h>
#include <pthread.h>
void *null_thread(void *p)
{
for (;;)
sleep(1);
return NULL;
}
void *exec_thread(void *p)
{
execl("/bin/true", "/bin/true", NULL);
return null_thread(p);
}
int main(int argc, char **argv)
{
for (;;) {
pid_t pid;
int ret, status;
pid = fork();
if (pid < 0)
break;
if (!pid) {
pthread_t tid;
pthread_create(&tid, NULL, exec_thread, NULL);
for (;;)
pthread_create(&tid, NULL, null_thread, NULL);
}
do {
ret = waitpid(pid, &status, 0);
} while (ret == -1 && errno == EINTR);
}
return 0;
}
quickly creates an unkillable task.
If copy_process(CLONE_THREAD) races with de_thread()
copy_signal()->atomic(signal->count) breaks the signal->notify_count
logic, and the execing thread can hang forever in kernel space.
Change copy_process() to increment count/live only when we know for sure
we can't fail. In this case the forked thread will take care of its
reference to signal correctly.
If copy_process() fails, check CLONE_THREAD flag. If it it set - do
nothing, the counters were not changed and current belongs to the same
thread group. If it is not set, ->signal must be released in any case
(and ->count must be == 1), the forked child is the only thread in the
thread group.
We need more cleanups here, in particular signal->count should not be used
by de_thread/__exit_signal at all. This patch only fixes the bug.
Reported-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Tested-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create a kernel/rcutree_plugin.h file that contains definitions
for preemptable RCU (or, under the #else branch of the #ifdef,
empty definitions for the classic non-preemptable semantics).
These definitions fit into plugins defined in kernel/rcutree.c
for this purpose.
This variant of preemptable RCU uses a new algorithm whose
read-side expense is roughly that of classic hierarchical RCU
under CONFIG_PREEMPT. This new algorithm's update-side expense
is similar to that of classic hierarchical RCU, and, in absence
of read-side preemption or blocking, is exactly that of classic
hierarchical RCU. Perhaps more important, this new algorithm
has a much simpler implementation, saving well over 1,000 lines
of code compared to mainline's implementation of preemptable
RCU, which will hopefully be retired in favor of this new
algorithm.
The simplifications are obtained by maintaining per-task
nesting state for running tasks, and using a simple
lock-protected algorithm to handle accounting when tasks block
within RCU read-side critical sections, making use of lessons
learned while creating numerous user-level RCU implementations
over the past 18 months.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: akpm@linux-foundation.org
Cc: mathieu.desnoyers@polymtl.ca
Cc: josht@linux.vnet.ibm.com
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
LKML-Reference: <12509746134003-git-send-email->
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The commit 2ff05b2b (oom: move oom_adj value) moveed the oom_adj value to
the mm_struct. It was a very good first step for sanitize OOM.
However Paul Menage reported the commit makes regression to his job
scheduler. Current OOM logic can kill OOM_DISABLED process.
Why? His program has the code of similar to the following.
...
set_oom_adj(OOM_DISABLE); /* The job scheduler never killed by oom */
...
if (vfork() == 0) {
set_oom_adj(0); /* Invoked child can be killed */
execve("foo-bar-cmd");
}
....
vfork() parent and child are shared the same mm_struct. then above
set_oom_adj(0) doesn't only change oom_adj for vfork() child, it's also
change oom_adj for vfork() parent. Then, vfork() parent (job scheduler)
lost OOM immune and it was killed.
Actually, fork-setting-exec idiom is very frequently used in userland program.
We must not break this assumption.
Then, this patch revert commit 2ff05b2b and related commit.
Reverted commit list
---------------------
- commit 2ff05b2b4e (oom: move oom_adj value from task_struct to mm_struct)
- commit 4d8b9135c3 (oom: avoid unnecessary mm locking and scanning for OOM_DISABLE)
- commit 8123681022 (oom: only oom kill exiting tasks with attached memory)
- commit 933b787b57 (mm: copy over oom_adj value at fork time)
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While looking at Jens Rosenboom bug report
(http://lkml.org/lkml/2009/7/27/35) about strange sys_futex call done from
a dying "ps" program, we found following problem.
clone() syscall has special support for TID of created threads. This
support includes two features.
One (CLONE_CHILD_SETTID) is to set an integer into user memory with the
TID value.
One (CLONE_CHILD_CLEARTID) is to clear this same integer once the created
thread dies.
The integer location is a user provided pointer, provided at clone()
time.
kernel keeps this pointer value into current->clear_child_tid.
At execve() time, we should make sure kernel doesnt keep this user
provided pointer, as full user memory is replaced by a new one.
As glibc fork() actually uses clone() syscall with CLONE_CHILD_SETTID and
CLONE_CHILD_CLEARTID set, chances are high that we might corrupt user
memory in forked processes.
Following sequence could happen:
1) bash (or any program) starts a new process, by a fork() call that
glibc maps to a clone( ... CLONE_CHILD_SETTID | CLONE_CHILD_CLEARTID
...) syscall
2) When new process starts, its current->clear_child_tid is set to a
location that has a meaning only in bash (or initial program) context
(&THREAD_SELF->tid)
3) This new process does the execve() syscall to start a new program.
current->clear_child_tid is left unchanged (a non NULL value)
4) If this new program creates some threads, and initial thread exits,
kernel will attempt to clear the integer pointed by
current->clear_child_tid from mm_release() :
if (tsk->clear_child_tid
&& !(tsk->flags & PF_SIGNALED)
&& atomic_read(&mm->mm_users) > 1) {
u32 __user * tidptr = tsk->clear_child_tid;
tsk->clear_child_tid = NULL;
/*
* We don't check the error code - if userspace has
* not set up a proper pointer then tough luck.
*/
<< here >> put_user(0, tidptr);
sys_futex(tidptr, FUTEX_WAKE, 1, NULL, NULL, 0);
}
5) OR : if new program is not multi-threaded, but spied by /proc/pid
users (ps command for example), mm_users > 1, and the exiting program
could corrupt 4 bytes in a persistent memory area (shm or memory mapped
file)
If current->clear_child_tid points to a writeable portion of memory of the
new program, kernel happily and silently corrupts 4 bytes of memory, with
unexpected effects.
Fix is straightforward and should not break any sane program.
Reported-by: Jens Rosenboom <jens@mcbone.net>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sonny Rao <sonnyrao@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both cpu itimers have same data flow in the few places, this
patch make unification of code related with VIRT and PROF
itimers.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
LKML-Reference: <1248862529-6063-2-git-send-email-sgruszka@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to be able to distinguish between no samples due to
inactivity and no samples due to task ended, Arjan asked for
PERF_EVENT_EXIT events. This is useful to the boot delay
instrumentation (bootchart) app.
This patch changes the PERF_EVENT_FORK to be emitted on every
clone, and adds PERF_EVENT_EXIT to be emitted on task exit,
after the task's counters have been closed.
This task tracing is controlled through: attr.comm || attr.mmap
and through the new attr.task field.
Suggested-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
[ cleaned up perf_counter.h a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>