Improve the existing boot/load time warnings from sata_mv
for Highpoint RocketRAID 23xx cards, based on new knowledge
about where the BIOS likes to overwrite sectors with metadata.
Harmless to us, but very useful for end users.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Like ST380817AS / 3.42, ST3160023AS / 3.42 times out commands if NCQ
is used. Blacklist it. This is reported by Matheus Izvekov in the
following thread.
http://thread.gmane.org/gmane.linux.ide/24202
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
link->eh_info.serror is used to cache SError for controllers which
need it cleared from interrupt handler to clear IRQ. It also should
be cleared after reset just like SError itself.
Make ata_std_postreset() clear link->eh_info.serror too and update
sata_sil such that it doesn't care about bookkeeping the value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Interestingly, sata_sil raises spurious interrupts if it's coupled
with Sil SATA_PATA bridge. Currently, sata_sil interrupt handler is
strict about spurious interrupts and freezes the port when it occurs.
This patch makes it more forgiving.
* On SATA PHY event interrupt, serror value is checked to see whether
it really is PHYRDY CHG event. If not, SATA PHY event interrupt is
ignored.
* If ATA interrupt occurs while no command is in progress, it's
cleared and ignored.
This fixes bugzilla bug 9505.
http://bugzilla.kernel.org/show_bug.cgi?id=9505
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch fixes the STATUS_RF_KILL_HW state is not cleared problem if the
device goes to suspend when the rf_kill switch is enabled. The bug causes
the driver always thinks the rf_kill switch is enabled (although it is
disabled) after resume.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes Bug #9414
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ia64:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c: In function `tsf_write_file':
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
We do not know what type was used to implement u64 and we can never use u64 in
printk(), sscanf(), etc.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that libertas selects WIRELESS_EXT, since selecting other stuff that
should depend on WEXT, like IEEE80211, doesn't seem to drag that in for us.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rate control algo reference leak in case if network device has been
failed to register. In this case special flag priv->mac80211_registered is
not set and the rate algo reference is not freeing on module unload. That
leads to OOPs in further ieee80211 rate register/unregister procedure (by
any callee).
It should fix the bug #9470http://bugzilla.kernel.org/show_bug.cgi?id=9470
[akpm@linux-foundation.org: build fix]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shaddy Baddah found an alignment problem with zd1211rw driver at
2007-11-19. This patch fixes it, it is based on the patch proposed by
Herbert Xu. The alignment 4 has been the agreed value on the
linux-wireless mailing list.
Notify that the problem does only affect the old zd1211rw softmac
driver and not the zd1211rw-mac80211 driver. Daniel Drake has
already provided a patch for the replacement of the softmac
driver, which this patch will break.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add Dan Williams as maintainer for libertas driver.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
MAINTAINERS: update the NFS CLIENT entry
NFS: Fix an Oops in NFS unmount
Revert "NFS: Ensure we return zero if applications attempt to write zero bytes"
SUNRPC xprtrdma: fix XDR tail buf marshalling for all ops
NFSv2/v3: Fix a memory leak when using -onolock
NFS: Fix NFS mountpoint crossing...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Re-journal buffers after transaction extend
ocfs2: Allow for debugging of transaction extends
ocfs2: Don't panic when truncating an empty extent
ocfs2: fix exit-while-locked bug in ocfs2_queue_orphans()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
HOWTO: update misspelling and word incorrected
add stable_api_nonsense.txt in korean
HOWTO: change addresses of maintainer and lxr url for Korean HOWTO
Add Documentation for FAIR_USER_SCHED sysfs files
HOWTO: Change man-page maintainer address for Japanese HOWTO
tipar: remove obsolete module
kobject: fix the documentation of how kobject_set_name works
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: revert portions of "UNUSUAL_DEV: Sync up some reported devices from Ubuntu"
usb: Remove broken optimisation in OHCI IRQ handler
USB: at91_udc: correct hanging while disconnecting usb cable
USB: use IRQF_DISABLED for HCD interrupt handlers
USB: fix locking loop by avoiding flush_scheduled_work
usb.h: fix kernel-doc warning
USB: option: Bind to the correct interface of the Huawei E220
USB: cp2101: new device id
usb-storage: Fix devices that cannot handle 32k transfers
USB: sierra: fix product id
Check in sis190_rx_interrupt() is broken on big-endian
(desc->status is little-endian and everything else actually uses
it correctly, including other checks for OWNbit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit ed7e63a51d has tried to fix
section mismatch:
WARNING: vmlinux.o(.init.text+0x17278): Section mismatch: reference to
.exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')
But that mismatch still happens.
This patch actually fixing section mismatch by removing __exit from
the header file.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ocfs2_extend_trans() might call journal_restart() which will commit dirty
buffers and then restart the transaction. This means that any buffers which
still need changes should be passed to journal_access() again. Some paths
during extend weren't doing this right.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
The nastiest cases of transaction extends are also the rarest. We can expose
them more quickly at the expense of performance by going straight to the
journal_restart() in ocfs2_extend_trans(). Wrap things in OCFS2_DEBUG_FS so
that we only do this when "expensive debugging" is turned on.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
We're holding the cluster lock when a failure might happen in
ocfs2_dir_foreach() so it needs to be released.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This reverts one change from 67fa10627e
that prevented userspace from seing the "driver disk" lun in a san disk
device. The kernel shouldn't do this, it's up to userspace to handle
this properly, if it somehow wants to filter this away.
Cc: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.
This mechanism can't be used on some controllers. Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.
This patch removes the optimisation and makes the code clearer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct hanging while disconnecting the USB device cable. Prevent a race
between vbus and UDP interrupts. This bug was tracked on at91sam9260ek
boards.
A usb resume interrupt was firing after the vbus interrupt : the IP was
then already stoped and not able to deal with it (no more clock). A simple
interrupt disabling is ok as the "end of bus reset" irq is non maskable and
ok to resume the USB device IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Host controller IRQs are supposed to be serviced with interrupts
disabled. This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it. It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().
This fixes Bugzilla #9335.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1027) replaces a call to flush_scheduled_work() -- a
dangerous routine to invoke, especially while holding any sort of lock
-- with calls to cancel_work_sync() and cancel_delayed_work_sync().
This fixes Bugzilla #9532.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix kernel-doc warning in usb.h:
Warning(linux-2.6.24-rc3-git7//include/linux/usb.h:166): No description found for parameter 'sysfs_files_created'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a bunch of problems we are having with the Huawei devices...
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a device ID for the Aerocomm Radio Modem, which uses the
cp2102. I'm sure changing num_bulk_in/num_bulk_out to NUM_DONT_CARE
is the wrong fix, but this is the only device I have with a cp2102,
so I have no idea what a good global value would be, if there is one.
Zero didn't work with this device.
From: Jeff Long <JeffLong@mitre.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a device cannot handle the smallest previously limited transfer
size (64 blocks) without stalling, limit the device to the amount of
packets that fit in a platform native page.
The lowest possible limit is PAGE_CACHE_SIZE, so if the device is ever
used on a platform that has larger than 8K pages, you lose unless you
can convince the device firmware folks to fix the issue.
Cc: Mathew Dharm <mdharm-scsi@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached is a patch to fix the addition of the new product ids I sent.
It is against 2.6.24-rc4, as Linus included the broken version of the
patch I sent you in that tree. :(
Not sure if this is the right method to go about this, but hopefully I got
it right this time.
Signed-off-by: Andrew Gilmore <agilmore@wirelessbeehive.com>
CC: Kevin Lloyd <klloyd@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restore PCI expansion ROM P2P prefetch window creation.
This patch reverts previous "Avoid creating P2P prefetch
window for expansion ROMs" change due to regressions that
were spotted on some systems.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So sorry. again My mail is set with EUC-kR.
I'll resend with UTF-8.
Signed-off-by: barrios <minchan.kim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch to change email address of man-page maintainer for
Japanese HOWTO document (Documentation/ja_JP/HOWTO).
This is for sync to Documentation/HOWTO that Michael Kerrisk mentioned
to me.
From: Tsugikazu Shibata <tshibata@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tipar: remove obsolete module
The tipar character driver was used to implement bit-banging access
to Texas Instruments parallel link cable. A user-land method now
exists thru PPDEV & PARPORT.
Signed-off-by: Romain Liévin <roms@lpg.ticalc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Dave Young <hidave.darkstar@gmail.com> for pointing out that I
forgot to update the comment when I rewrote kobject_set_name.
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] add Nano 7240 driver
[WATCHDOG] ipmi: add the standard watchdog timeout ioctls
[WATCHDOG] IT8212F watchdog driver
[WATCHDOG] Sbus: cpwatchdog, remove SPIN_LOCK_UNLOCKED
[WATCHDOG] bfin_wdt, remove SPIN_LOCK_UNLOCKED
[WATCHDOG] Stop looking for device as soon as one is found
[WATCHDOG] at32ap700x_wdt: add support for boot status and add fix for silicon errata
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix lock flag variable location, bump version number
IB/ehca: Serialize HCA-related hCalls if necessary
IB/ehca: Return correct number of SGEs for SRQ
Mark Lord
Tejun Heo
Jeff Garzik
Zhu Yi
Larry Finger
Andrew Morton
Dan Williams
Cyrill Gorcunov
Adrian Bunk
Ulrich Kunitz
Stefano Brivio
Linus Torvalds
Al Viro
Anton Vorontsov
Komuro
Mark Fasheh
Greg Kroah-Hartman
Benjamin Herrenschmidt
Nicolas Ferre
Alan Stern
Randy Dunlap
Jaime Velasco Juan
Jeff Long
Doug Maxey
agilmore@wirelessbeehive.com
Gary Hade
barrios
Dhaval Giani
Tsugikazu Shibata
Romain Liévin