Compute context pointer in hdev shouldn't be used for fetching the
context's pointer.
If an object needs the context's pointer, it should get it while
incrementing its kref, and when the object is released, put it.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver supports only a single context. Therefore, no need to check
if the user context that is closed is the compute context. The user
context, if exists, is always the compute context.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix a bug where in case of failure to allocate idr, the handle's
memory wasn't freed as part of the error handling code.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The reset flags used by the reset thread are currently a mix of
hard-coded values and a specific flag which is passed from the context
that initiates the reset.
To make it easier to pass more flags in future from this context to the
reset thread, modify it to pass all the original reset flags to the
thread.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Because info ioctl is used to retrieve data, some of its opcodes may be
used during hard reset.
Other ioctls should be blocked while device is not operational.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
For debug purpose, add SOB address and SOB initial counter value
before current submission to uAPI output.
Using SOB address and initial counter, user can calculate how much of
the submmision has been completed.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reporting FW errors involves reading of the error registers.
In case we have a corrupted FW descriptor we cannot do that since the
dynamic scratchpad is potentially corrupted as well and may cause kernel
crush when attempting access to a corrupted register offset.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Driver should handle events during soft-reset as F/W is not
going through reset and it keeps sending events towards host.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently we dump the physical IRQ line index in host if an event
is received during reset. This ID is confusing as it means nothing
to the user.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In new f/w versions, it is required to explicitly indicate the power
information type when querying the F/W for power info.
When getting the current power level it should be set to power_input.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Some info ioctls can be served even if the device is disabled or
in reset. Hence, we enable more info ioctls during reset, as these
ioctls do not require any H/W nor F/W communication.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Race example scenario:
1. User have 2 threads that waits on multi CS:
- thread_0 waits on QID 0 and uses multi CS context 0.
- thread_1 waits on QID 1 and uses multi CS context 1.
2. thread_1 got completion and release multi CS context 1.
3. CS related to multi CS of thread_0 starts executing
complete_multi_cs function, the first iteration of the loop
completes the multi CS of thread_0, hence multi CS context 0
is released.
4. thread_1 waits on QID 1 and uses multi CS context 0.
5. thread_0 waits on QID 0 and uses multi CS context 1.
6. The second iterattion of the loop (from step 3) starts, which
means, start checking multi CS context 1:
- multi CS contetxt is being used by thread_0 waiting on QID 0.
- The fence of the CS (still CS from step 3) has QID map the same
as the multi CS context 1.
- multi CS context 1 (thread_0) gets completion on CS that triggered
already thread_0 (with multi CS context 0) and is no longer
being waited on.
Fixed by exiting the loop in complete_multi_cs after getting completion
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As device boot warnings clears the indication from the error mask,
they must be located together before the unknown error validation.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
GAUDI supports only hard-reset. Therefore, this function should
return an error of operation not permitted.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The ASIC-specific soft_reset_late_init() is now called after either
soft-reset or reset-upon-device-release. Therefore, it needs a more
appropriate name.
No need to split it to two functions, as an ASIC either supports
soft-reset or reset-upon-device-release.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reset upon device release is not a soft-reset from user/system point
of view. As such, we shouldn't count that reset in the statistics we
gather and expose to the monitoring applications.
We also shouldn't print soft-reset when doing the reset upon device
release.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Changing the frequency automatically is only done in Goya. In future
ASICs this is done inside the firmware. Therefore, move the common code
into the Goya specific files.
Main changes as part of the commit are:
1. The thread for setting frequency is moved from device_late_init
to goya_late_init
2. hl_device_set_frequency is removed from hl_device_open as it is
not relevant for other ASICs and for Goya it is taken care by
the thread
3. hl_device_set_frequency is renamed as goya_set_frequency
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Hard-reset is mutually exclusive with reset-on-device-release.
Therefore, if such a request arrives to the reset function, abort
the reset and return an error to the callee.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently there is a deadlock in driver in scenarios where MMU
cache invalidation fails. The issue is basically device reset
being performed without releasing the MMU mutex.
The solution is to skip device reset as it is not necessary.
In addition we introduce a slight code refactor that prints the
invalidation error from a single location.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Getting the used PLL index with which to send the CPUPU packet relies on
the CPUCP info packet.
In case CPU queues are not enabled getting the PLL index will issue an
error and in some ASICs will also fail the driver load.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Move an entry in the debugfs documentation to align with the
alphabetical order which is kept this file.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If a device reset has started, there is a chance that the heartbeat
function will fail because the device is disabled at the beginning
of the reset function.
In that case, we don't want the error message to appear in the log.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
A new uAPI is added for debug purposes of the user-space to retrieve
errors related data from previous session (before device reset was
performed).
Inforamtion is filled when a razwi or CS timeout happens and can
contain one of the following:
1. Retrieve timestamp of last time the device was opened and razwi or
CS timeout happened.
2. Retrieve information about last CS timeout.
3. Retrieve information about last razwi error.
This information doesn't contain user data, so no danger of data
leakage between users.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
AS TPM error indication is not fatal, driver should dump a warning
and continue booting.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
I2C debugfs support is limited to 1 byte. We extend functionality
to more than 1 byte by using one of the pad fields as a length.
No backward compatibility issues as new F/W versions will treat 0
length as a 1 byte length transaction.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Divide the code into 3 different parts:
- Copy kernel parameters
- Setting device behaivor per asic
- Fixup of various device parameters according to the device behaivor.
In addition, remove non-relevant code for upstream (simulator support).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add implementation for new opcodes in the INFO IOCTL:
1. Retrieve the replaced DRAM rows from f/w.
2. Retrieve the pending DRAM rows from f/w.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Refactor the wait-for-user-interrupt routine to make it more
generic for re-use for other user exposed h/w interfaces in future
ASICs.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In Signaling-From-Graph case, the driver didn't set the hw_sob pointer
at the right place, which is needed for the cs completion
check prior to start sending all the master/slaves jobs to device.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In addition to the clock throttling reason, user should be able
to obtain also the start time and the duration of the throttling
event.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to increase maximum wait-for-interrupt timeout, change it
to 64 bit variable. This wait is used only by newer ASICs, so no
problem in changing this interface at this time.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
CPUCP_PACKET_POWER_GET packet type was used for both
hl_get_power() and hl_set_power().
To align with other sensor functions hl_set_power()
should use CPUCP_PACKET_POWER_SET.
This packet will only be used with newer ASICs, so need to add
a compatibility flag to the asic properties to indicate whether to use
this packet or the GET packet.
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case of device reset, the driver does a force trigger on all waiting
users to release them from waiting. However, the driver does not handle
error scenario while waiting.
hl_interrupt_wait_ioctl() now exits the wait in case of an error with
abort status.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Once we read indication of whether f/w is doing the reset, we don't
want to clear it, until the next time we read this indication.
Otherwise, we might be in a state of wrong indication.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Using a variable poll interval for fw loading allows us to support
much slower environments (emulation) while changing only a single
line in the code, instead of choosing a different interval in each
function that polls.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Up until now the driver stored indication if Linux was loaded on the
device CPU. This was needed in order to coordinate some tasks that are
performed by the Linux.
In future ASICs, many of those tasks will be performed by the boot
fit, so now we need the same indication of boot fit load status.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The PCI MMU cache is two layered. The upper layer, memcache, uses cache
lines, the bottom layer doesn't.
Hence, after PMMU map operation we have to invalidate memcache, to avoid
the situation where the new entry is already in the cache due to its
cache line being fully in the cache.
However, we do not have to invalidate the lower cache, and here we can
optimize, since cache invalidation is time consuming.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The enum vm_type was abused, used once as a value (indication
memory type for map) and once as a flag (for cache invalidation).
This makes it hard to add new and still keep it meaningful, hence it
is better to split into one enum for values and one for flags.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently LAST_MASK is a global, but really it is an MMU implementation
specific. We need this change for future ASICs.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
VA blocks are currently stored in an inconsistent way. Sometimes block
end is inclusive, sometimes exclusive. This leads to wrong size
calculations in certain cases, plus could lead to a segmentation fault
in case mapping process fails in the middle and we try to roll it back.
Need to make this consistent - start inclusive till end inclusive.
For example, the regions table may now look like this:
0x0000 - 0x1fff : allocated
0x2000 - 0x2fff : free
0x3000 - 0x3fff : allocated
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Do not use a dma channel for debugfs requested transfer if it's
QM is not idle.
Signed-off-by: Guy Zadicario <gzadicario@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The boot status flag "SRAM available" can be set by f/w Linux (in the
general case) or by f/w uboot (in some specific debug scenario) but
never by f/w preboot.
Hence, when polling the boot status flags in the preboot stage we do not
want to poll on "SRAM Avialable".
The special case in which uboot set this flag is when we are running
special debug scenario without Linux. In this case, at some point during
the boot, the uboot relocates its code to the DRAM and then set the
specified flag.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
VA range info could assist in debugging VA allocation bugs.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There are rare cases where the device CPU's watchdog has expired and as
a result, the watchdog reset has happened and the CPU will now move to
running its preboot f/w.
When that happens, the driver will only know that a heartbeat failure
occurred. As a result, the driver will send a message to the CPU's main
f/w asking it to reset the device, but because the CPU is now running
preboot, it won't respond and the re-initialization process will later
fail when trying to load the f/w.
The solution is to send the request to the preboot as well, only if the
reset was caused because of HB failure.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In the dynamic FW load protocol the boot status is updated to
"Ready to Boot" once uboot is active.
Polling on other boot status values is a residue of code duplication
from the static protocol and should be removed.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
-----BEGIN PGP SIGNATURE-----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=xXvq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 5.17
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
MAINTAINERS: Add maintainer for xilinx-ams
dt-bindings: iio: adc: Add Xilinx AMS binding documentation
iio: adc: Add Xilinx AMS driver
device property: Add fwnode_iomap()
iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
iio:dummy: Drop set but unused variable len.
iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
drivers:iio:dac: Add AD3552R driver support
dt-bindings: iio: dac: Add adi,ad3552r.yaml
...
Unfortuanately a non standards compliant ACPI ID is known to be
in the wild on some AAEON boards.
Partly revert the removal of these IDs so that ADC081C will again
work + add a comment to that affect for future reference.
Whilst here use generic firmware properties rather than the ACPI
specific handling previously found in this driver.
Reported-by: Kunyang Fan <Kunyang_Fan@aaeon.com.tw>
Fixes: c458b7ca3f ("iio:adc:ti-adc081c: Drop ACPI ids that seem very unlikely to be official.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Kunyang Fan <Kunyang_Fan@aaeon.com.tw> #UP-extremei11
Link: https://lore.kernel.org/r/20211205172728.2826512-1-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
I don't believe it's possible to hit this, because we drop
out of __iio_update_buffers() earlier in the event of an empty
list. However, that is not visible to the compiler so lets
return an error if we do hit the loop with an empty bitmask.
Fixes: 5d97d9e9a7 ("iio: addac: ad74413r: fix off by one in ad74413r_parse_channel_config()")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20211220164726.3136307-1-jic23@kernel.org
Oded Gabbay
Tomer Tayar
Dani Liberman
Ohad Sharabi
Ofir Bitton
Rajaravi Krishna Katta
farah kassabri
Bharat Jauhari
Yuri Nudelman
Guy Zadicario
Greg Kroah-Hartman
Jonathan Cameron