According to the kernel power management documentation freeze phase
should only quiesce the device, no need to configure wakes or put it to
low power state. For this reason we simply stop the control channel and
in case of Software Connection Manager also mark the hotplug disabled.
This should align the driver better with the PM framework expectations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds runtime PM support for the Software Connection Manager parts
of the driver. This allows to save power when either there is no device
attached at all or there is a device attached and all following
conditions are true:
- Tunneled PCIe root/downstream ports are runtime suspended
- Tunneled USB3 ports are runtime suspended
- No active DisplayPort stream
- No active XDomain connection
For the first two we take advantage of device links that were added in
previous patch. Difference for the system sleep case is that we also
enable wakes when something is geting plugged in/out of the Thunderbolt
ports.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec mandates that the lane 1 should be disabled if lanes are not
bonded. For host-to-host connections (XDomain) we don't support lane
bonding so in order to be compatible with the spec, disable lane 1 when
another host is connected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When the port is connected to another host it should be marked as such
in the USB4 port capability. This information is used by the router
during sleep and wakeup.
Also do the same for legacy switches via link controller vendor specific
registers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
During testing it was noticed that the link is not properly restored
after the domain exits sleep if the link configured bits are set before
lane bonding is enabled. The USB4 spec does not say in which order these
need to be set but setting link configured afterwards makes the link
restoration work so we do that instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
DP tunnels do not need the same kind of treatment as others because they
are created based on hot-plug events on DP adapter ports, and the
display stack does not need the tunnels to be enabled when resuming from
suspend. Also Tiger Lake Thunderbolt controller sends unplug event on D3
exit so this avoids that as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
First generation routers may need the reset command upon resume but it
is not supported by newer generations.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec specifies standard access to retimers (both on-board and
cable) through USB4 port sideband access. This makes it possible to
upgrade their firmware in the same way than we already do with the
routers.
This enumerates on-board retimers under each USB4 port when the link
comes up and adds them to the bus under the router the retimer belongs
to. Retimers are exposed in sysfs with name like <device>:<port>.<index>
where device is the router the retimer belongs to, port is the USB4 port
the retimer is connected to and index is the retimer index under that
port (starting from 1). This applies to the upstream USB4 port as well
so if there is on-board retimer between the port and the router it is
also added accordingly.
At this time we do not add cable retimers but there is no techincal
restriction to do so in the future if needed. It is not clear whether it
makes sense to upgrade their firmwares and at least Thunderbolt 3 cables
it has not been done outside of lab environments.
The sysfs interface is made to follow the router NVM upgrade to make it
easy to extend the existing userspace (fwupd) to handle these as well.
Signed-off-by: Kranthi Kuntala <kranthi.kuntala@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB3 supports both isochronous and non-isochronous traffic. The former
requires guaranteed bandwidth and can take up to 90% of the total
bandwidth. With USB4 USB3 is tunneled over USB4 fabric which means that
we need to make sure there is enough bandwidth allocated for the USB3
tunnels in addition to DisplayPort tunnels.
Whereas DisplayPort bandwidth management is static and done before the
DP tunnel is established, the USB3 bandwidth management is dynamic and
allows increasing and decreasing the allocated bandwidth according to
what is currently consumed. This is done through host router USB3
downstream adapter registers.
This adds USB3 bandwidth management to the software connection manager
so that we always try to allocate maximum bandwidth for DP tunnels and
what is left is allocated for USB3.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Whereas DisplayPort bandwidth is consumed only in one direction (from DP
IN adapter to DP OUT adapter), USB3 adds separate bandwidth for both
upstream and downstream directions.
For this reason extend the tunnel consumed bandwidth routines to support
both directions and implement this for DP.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Just for symmetry with the usb4_switch_map_usb3_down() make this one
also return ports that are enabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to call this on enabled ports in order to find the mapping from
host router USB4 port to a USB 3.x downstream adapter, so make the
function return enabled ports as well.
While there fix parameter alignment in tb_find_usb3_down().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB3 tunneling is possible only over USB4 link so don't create USB3
tunnels if that's not the case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec allows DP tunneling from any router that has DP IN adapter,
not just from host router. The driver currently only added the DP IN
resources for the host router because Thunderbolt 1, 2 and 3 devices do
not have DP IN adapters. However, USB4 allows device routers to have DP
IN adapter as well so update the driver to add DP IN resources for each
device that has one. One example would be an eGPU enclosure where the
eGPU output is forwarded to DP IN port and then tunneled over the USB4
fabric.
Only limitation we add now is that the DP IN and DP OUT that gets paired
for tunnel creation should both be under the same topology starting from
host router downstream port. In other words we do not create DP tunnels
across host router at this time even though that is possible as well but
it complicates the bandwidth management and there is no real use-case
for this anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 added a capability to tunnel USB 3.x protocol over the USB4
fabric. USB4 device routers may include integrated SuperSpeed HUB or a
function or both. USB tunneling follows PCIe so that the tunnel is
created between the parent and the child router from USB3 downstream
adapter port to USB3 upstream adapter port over a single USB4 link.
This adds support for USB 3.x tunneling and also capability to discover
existing USB 3.x tunnels (for example created by connection manager in
boot firmware).
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-9-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Time Management Unit (TMU) is included in each USB4 router. It is used
to synchronize time across the USB4 fabric. By default when USB4 router
is plugged to the domain, its TMU is turned off. This differs from
Thunderbolt (1, 2 and 3) devices whose TMU is by default configured to
bi-directional HiFi mode. Since time synchronization is needed for
proper Display Port tunneling this means we need to configure the TMU on
USB4 compliant devices.
The USB4 spec allows some flexibility on how the TMU can be configured.
This makes it possible to enable link power management states (CLx) in
certain topologies, where for example DP tunneling is not used. TMU can
also be re-configured dynamicaly depending on types of tunnels created
over the USB4 fabric.
In this patch we simply configure the TMU to be in bi-directional HiFi
mode. This way we can tunnel any kind of traffic without need to perform
complex steps to re-configure the domain dynamically. We can add more
fine-grained TMU configuration later on when we start enabling CLx
states.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-8-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 is the public specification based on Thunderbolt 3 protocol. There
are some differences in register layouts and flows. In addition to PCIe
and DP tunneling, USB4 supports tunneling of USB 3.x. USB4 is also
backward compatible with Thunderbolt 3 (and older generations but the
spec only talks about 3rd generation). USB4 compliant devices can be
identified by checking USB4 version field in router configuration space.
This patch adds initial support for USB4 compliant hosts and devices
which enables following features provided by the existing functionality
in the driver:
- PCIe tunneling
- Display Port tunneling
- Host and device NVM firmware upgrade
- P2P networking
This brings the USB4 support to the same level that we already have for
Thunderbolt 1, 2 and 3 devices.
Note the spec talks about host and device "routers" but in the driver we
still use term "switch" in most places. Both can be used interchangeably.
Co-developed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-5-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 1.0 section 6.4.2.7 specifies a new field (PG) in notification
packet that is sent as response of hot plug/unplug events. This field
tells whether the acknowledgment is for plug or unplug event. This needs
to be set accordingly in order the router to send further hot plug
notifications.
To make it simpler we fill the field unconditionally. Legacy devices do
not look at this field so there should be no problems with them.
While there rename tb_cfg_error() to tb_cfg_ack_plug() and update the
log message accordingly. The function is only used to ack plug/unplug
events.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-4-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will be needing this when adding initial USB4 support so make it
available to other files in the driver as well. We also rename it to
tb_switch_find_port() to follow conventions used in switch.c.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-2-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since now we can do pretty much the same thing in the software
connection manager than the firmware would do, there is no point
starting it by default. Instead we can just continue using the software
connection manager.
Make it possible for user to switch between the two by adding a module
pararameter (start_icm) which is by default false. Having this ability
to enable the firmware may be useful at least when debugging possible
issues with the software connection manager implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Titan Ridge supports Display Port 1.4 which adds HBR3 (High Bit Rate)
rates that may be up to 8.1 Gb/s over 4 lanes. This translates to
effective data bandwidth of 25.92 Gb/s (as 8/10 encoding is removed by
the DP adapters when going over Thunderbolt fabric). If another high
rate monitor is connected we may need to reduce the bandwidth it
consumes so that it fits into the total 40 Gb/s available on the
Thunderbolt fabric.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To perform proper Display Port tunneling for Thunderbolt 3 devices we
need to allocate DP resources for DP IN port before they can be used.
The reason for this is that the user can also connect a monitor directly
to the Type-C ports in which case the Thunderbolt controller acts as
re-driver for Display Port (no tunneling takes place) taking the DP
sinks away from the connection manager. This allocation is done using
special sink allocation registers available through the link controller.
We can pair DP IN to DP OUT only if
* DP IN has sink allocated via link controller
* DP OUT port receives hotplug event
For DP IN adapters (only for the host router) we first query whether
there is DP resource available (it may be the previous instance of the
driver for example already allocated it) and if it is we add it to the
list. We then update the list when after each plug/unplug event to a DP
IN/OUT adapter. Each time the list is updated we try to find additional
DP IN <-> DP OUT pairs for tunnel establishment. This strategy also
makes it possible to establish another tunnel in case there are 3
monitors connected and one gets unplugged releasing the DP IN adapter
for the new tunnel.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to keep PCIe hierarchies consistent across hotplugs, add
hard-coded PCIe downstream port to Thunderbolt port for Alpine Ridge and
Titan Ridge as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For a casual reader tb_switch_is_cr() does not tell much so instead
spell out the full controller name in the function name. For example
tb_switch_is_cr() becomes tb_switch_is_cactus_ridge() which is easier
to understand.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Lane bonding allows aggregating two 10/20 Gb/s (depending on the
generation) lanes into a single 20/40 Gb/s bonded link. This allows
sharing the full bandwidth more efficiently. In order to establish lane
bonding we need to check that lane bonding is possible through link
controller and that both ends of the link actually supports 2x widths.
This also means that all the paths should be established through the
primary port so update tb_path_alloc() to handle this as well.
Lane bonding is supported starting from Falcon Ridge (2nd generation)
controllers.
We also expose the current speed and number of lanes under each device
except the host router following similar attribute naming than USB bus.
Expose speed and number of lanes for both directions to allow possibility
of asymmetric link in the future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There are quite many places in the driver where we iterate over each
port in the switch. To make it bit more convenient, add a macro that can
be used to iterate over each port and convert existing call sites to use it.
This is based on code by Lukas Wunner.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that the driver can handle every possible tunnel types there is no
point to log everything as info level so turn these to happen at debug
level instead.
While at it remove duplicated tunnel activation log message
(tb_tunnel_activate() calls tb_tunnel_restart() which print the same
message) and add one missing '\n' termination.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Two domains (hosts) can be connected through a Thunderbolt cable and in
that case they can start software services such as networking over the
high-speed DMA paths. Now that we have all the basic building blocks in
place to create DMA tunnels over the Thunderbolt fabric we can add this
support to the software connection manager as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to detect possible connections to other domains we need to be
able to find out why tb_switch_alloc() fails so make it return ERR_PTR()
instead. This allows the caller to differentiate between errors such as
-ENOMEM which comes from the kernel and for instance -EIO which comes
from the hardware when trying to access the possible switch.
Convert all the current call sites to handle this properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that we have capability to discover existing tunnels during driver
load there is no point tearing down tunnels when the driver gets
unloaded. Instead we can just leave them running. If user disconnects
devices while there is no Thunderbolt driver loaded, tunneled protocol
hotplug happens and is handled by the corresponding driver (pciehp in
case of PCIe tunnel, GFX driver in case of DP tunnel).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Display Port tunnels are somewhat more complex than PCIe tunnels as it
requires 3 tunnels (AUX Rx/Tx and Video). In addition we are not
supposed to create the tunnels immediately when a DP OUT is enumerated.
Instead we need to wait until we get hotplug event to that adapter port
or check if the port has HPD set before tunnels can be established. This
adds Display Port tunneling support to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We will be needing these routines to find Display Port adapters as well
so modify them to take port type as the second parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The only way to expand Thunderbolt topology is through the NULL adapter
ports (typically ports 1, 2, 3 and 4). There is no point handling
Thunderbolt hotplug events on any other port.
Add a helper function (tb_port_is_null()) that can be used to determine
if the port is NULL port, and use it in software connection manager code
when hotplug event is handled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the software connection manager (tb.c) has only supported
creating a single PCIe tunnel, no PCIe device daisy chaining has been
supported so far. This updates the software connection manager so that
it now can create PCIe tunnels for full chain of six devices.
Because PCIe allows DMA and opens possibility for DMA attacks we change
security level to "user" meaning that PCIe tunneling requires that the
userspace authorizes the devices first. This makes it possible to block
PCIe tunneling completely while still allowing other types of tunnels to
be automatically created.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Apple Macs the boot firmware (EFI) connects all devices automatically
when the system is started, before it hands over to the OS. Instead of
ignoring we discover all those PCIe tunnels and record them using our
internal structures, just like we do when a device is connected after
the OS is already up.
By doing this we can properly tear down tunnels when devices are
disconnected. Also this allows us to resume the existing tunnels after
system suspend/resume cycle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the driver only assigns remote port for the primary port if in
case of dual link. This makes things such as walking from one port to
another more complex than necessary because the code needs to change
from secondary to primary port if the path that is established is
created using secondary links.
In order to always assign both remote pointers we need to prevent the
scanning code from following the secondary link. Failing to do that
might cause problems as the same switch may be enumerated twice (or
removed in case of unplug). Handle that properly by introducing a new
function tb_port_has_remote() that returns true only for the primary
port. We also update tb_is_upstream_port() to support both dual link
ports, make it take const port pointer and move it below
tb_upstream_port() to keep similar functions close.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To be able to tunnel non-PCIe traffic, separate tunnel functionality
into generic and PCIe specific parts. Rename struct tb_pci_tunnel to
tb_tunnel, and make it hold an array of paths instead of just two.
Update all the tunneling functions to take this structure as parameter.
We also move tb_pci_port_active() to switch.c (and rename it) where we
will be keeping all port and switch related functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to tunnel non-PCIe traffic as well rename tunnel_pci.[ch] to
tunnel.[ch] to reflect this fact. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The adapter specific capability either is there or not if the port does
not hold an adapter. Instead of always finding it on-demand we read the
offset just once when the port is initialized.
While there we update the struct port documentation to follow kernel-doc
format.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_switch_find_by_route() does the same already so use it instead and
remove duplicated get_switch_at_route().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Currently the driver logs quite a lot to the system message buffer even
when doing normal operations. This information is not useful for
ordinary users and might even annoy some.
For this reason convert most of the logs at info level to happen at
debug level instead. The nice output formatting is untouched.
Logging can be easily re-enabled by passing "thunderbolt.dyndbg" in the
kernel command line (or using the corresponding control file runtime).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc and other driver subsystem patches for
4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
Note, there will be a merge conflict in drivers/misc/lkdtm_core.c when
merging to your tree as one lkdtm patch came in through the perf tree as
well as this one. The resolution is to take the const change that this
tree provides.
All of these have been in linux-next for quite a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWg2Lnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTUwCgwp46+I8yPlgDH8oe5TxyyJnpdHQAn1XW0i+a
sBi6WS87In5v1QO1Rgfc
=dH2a
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
Add a ̣̣continue statement in order to avoid using a previously
free'd pointer tunnel in list_add.
Addresses-Coverity-ID: 1415336
Fixes: 9d3cce0b61 ("thunderbolt: Introduce thunderbolt bus and connection manager")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend ACPI bus scan with DMI checks whether we're running
on a Mac to support Apple device properties in AML. The DMI checks are
performed for every single device, adding overhead for everything x86
that isn't Apple, which is the majority. Rafael and Andy therefore
request to perform the DMI match only once and cache the result.
Outside of ACPI various other Apple DMI checks exist and it seems
reasonable to use the cached value there as well. Rafael, Andy and
Darren suggest performing the DMI check in arch code and making it
available with a header in include/linux/platform_data/x86/.
To this end, add early_platform_quirks() to arch/x86/kernel/quirks.c
to perform the DMI check and invoke it from setup_arch(). Switch over
all existing Apple DMI checks, thereby fixing two deficiencies:
* They are now #defined to false on non-x86 arches and can thus be
optimized away if they're located in cross-arch code.
* Some of them only match "Apple Inc." but not "Apple Computer, Inc.",
which is used by BIOSes released between January 2006 (when the first
x86 Macs started shipping) and January 2007 (when the company name
changed upon introduction of the iPhone).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Suggested-by: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Starting from Intel Falcon Ridge the NVM firmware can be upgraded by
using DMA configuration based mailbox commands. If we detect that the
host or device (device support starts from Intel Alpine Ridge) has the
DMA configuration based mailbox we expose NVM information to the
userspace as two separate Linux NVMem devices: nvm_active and
nvm_non_active. The former is read-only portion of the active NVM which
firmware upgrade tools can be use to find out suitable NVM image if the
device identification strings are not enough.
The latter is write-only portion where the new NVM image is to be
written by the userspace. It is up to the userspace to find out right
NVM image (the kernel does very minimal validation). The ICM firmware
itself authenticates the new NVM firmware and fails the operation if it
is not what is expected.
We also expose two new sysfs files per each switch: nvm_version and
nvm_authenticate which can be used to read the active NVM version and
start the upgrade process.
We also introduce safe mode which is the mode a switch goes when it does
not have properly authenticated firmware. In this mode the switch only
accepts a couple of commands including flashing a new NVM firmware image
and triggering power cycle.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Intel Falcon Ridge the internal connection manager running
on the Thunderbolt host controller has been supporting 4 security
levels. One reason for this is to prevent DMA attacks and only allow
connecting devices the user trusts.
The internal connection manager (ICM) is the preferred way of connecting
Thunderbolt devices over software only implementation typically used on
Macs. The driver communicates with ICM using special Thunderbolt ring 0
(control channel) messages. In order to handle these messages we add
support for the ICM messages to the control channel.
The security levels are as follows:
none - No security, all tunnels are created automatically
user - User needs to approve the device before tunnels are created
secure - User need to approve the device before tunnels are created.
The device is sent a challenge on future connects to be able
to verify it is actually the approved device.
dponly - Only Display Port and USB tunnels can be created and those
are created automatically.
The security levels are typically configurable from the system BIOS and
by default it is set to "user" on many systems.
In this patch each Thunderbolt device will have either one or two new
sysfs attributes: authorized and key. The latter appears for devices
that support secure connect.
In order to identify the device the user can read identication
information, including UUID and name of the device from sysfs and based
on that make a decision to authorize the device. The device is
authorized by simply writing 1 to the "authorized" sysfs attribute. This
is following the USB bus device authorization mechanism. The secure
connect requires an additional challenge step (writing 2 to the
"authorized" attribute) in future connects when the key has already been
stored to the NVM of the device.
Non-ICM systems (before Alpine Ridge) continue to use the existing
functionality and the security level is set to none. For systems with
Alpine Ridge, even on Apple hardware, we will use ICM.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the control channel (ctl.c) handles the one supported
notification (PLUG_EVENT) and sends back ACK accordingly. However, we
are going to add support for the internal connection manager (ICM) that
needs to handle a different notifications. So instead of dealing
everything in the control channel, we change the callback to take an
arbitrary thunderbolt packet and convert the native connection manager
to handle the event itself.
In addition we only push replies we know of to the response FIFO.
Everything else is treated as notification (or request) and is expected
to be dealt by the connection manager implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt domain consists of switches that are connected to each
other, forming a bus. This will convert each switch into a real Linux
device structure and adds them to the domain. The advantage here is
that we get all the goodies from the driver core, like reference
counting and sysfs hierarchy for free.
Also expose device identification information to the userspace via new
sysfs attributes.
In order to support internal connection manager (ICM) we separate switch
configuration into its own function (tb_switch_configure()) which is
only called by the existing native connection manager implementation
used on Macs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika Westerberg
Kranthi Kuntala
Rajmohan Mani
Linus Torvalds
Gustavo A. R. Silva
Greg Kroah-Hartman
Lukas Wunner