For some reason they didn't get replaced so far by their
paravirt equivalents, resulting in code to be run with
interrupts disabled that doesn't expect so (causing, in the
observed case, a BUG_ON() to trigger) when syscall auditing is
enabled.
David (Cc-ed) came up with an identical fix, so likely this can
be taken to count as an ack from him.
Reported-by: Peter Moody <pmoody@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/5108E01902000078000BA9C5@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Tested-by: Peter Moody <pmoody@google.com>
This patch (as1654) fixes a very old bug in ehci-hcd, connected with
scheduling of periodic split transfers. The calculations for
full/low-speed bus usage are all carried out after the correction for
bit-stuffing has been applied, but the values in the max_tt_usecs
array assume it hasn't been. The array should allow for allocation of
up to 90% of the bus capacity, which is 900 us, not 780 us.
The symptom caused by this bug is that any isochronous transfer to a
full-speed device with a maxpacket size larger than about 980 bytes is
always rejected with a -ENOSPC error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1653) fixes a bug in ehci-hcd. Unlike iTD entries, an
siTD entry in the periodic schedule may not complete until the frame
after the one it belongs to. Consequently, when scanning the periodic
schedule it is necessary to start with the frame _preceding_ the one
where the previous scan ended.
Not doing this properly can result in memory leaks and failures to
complete isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andy Leiserson <andy@leiserson.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For BUCK10 the control registers are wrongly set as buck9 control register
This patch corrects the control registers for buck10
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
Pull console lockdep checking revert from Dave Airlie.
The lockdep splat this showed was interesting, but it's very very old,
and we won't be fixing it until 3.9. In the meantime, undo the lockdep
annotation so that we don't generate the (known) console lockdep issue,
and then possibly hide any potential other (unknown) lockdep problems
that got disabled by the first one that triggered.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "console: implement lockdep support for console_lock"
This reverts commit daee779718.
I'll requeue this after the console locking fixes, so lockdep
is useful again for people until fbcon is fixed.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add VID, PID and fixed interface for Telit LE920
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
They will be created at output, if ever needed. This avoids creating
empty neighbor entries when TPROXYing/Forwarding packets for addresses
that are not even directly reachable.
Note that IPv4 already handles it this way. No neighbor entries are
created for local input.
Tested by myself and customer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFS4ERR_DELAY is a legal reply when we call DESTROY_SESSION. It
usually means that the server is busy handling an unfinished RPC
request. Just sleep for a second and then retry.
We also need to be able to handle the NFS4ERR_BACK_CHAN_BUSY return
value. If the NFS server has outstanding callbacks, we just want to
similarly sleep & retry.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
This fixes a livelock in the xprt->sending queue where we end up never
making progress on lower priority tasks because sleep_on_priority()
keeps adding new tasks with the same owner to the head of the queue,
and priority bumps mean that we keep resetting the queue->owner to
whatever task is at the head of the queue.
Regression introduced by commit c05eecf636
(SUNRPC: Don't allow low priority tasks to pre-empt higher priority ones).
Reported-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QrJx
-----END PGP SIGNATURE-----
Merge tag 'efi-for-3.8' into x86/efi
Various urgent EFI fixes and some warning cleanups for v3.8
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Ensure that any setattr and getattr requests for junctions and/or
mountpoints are sent to the server. Ever since commit
0ec26fd069 (vfs: automount should ignore LOOKUP_FOLLOW), we have
silently dropped any setattr requests to a server-side mountpoint.
For referrals, we have silently dropped both getattr and setattr
requests.
This patch restores the original behaviour for setattr on mountpoints,
and tries to do the same for referrals, provided that we have a
filehandle...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
A device sending 0 length frames as fast as it can has been
observed killing the host system due to the resulting memory
pressure.
Temporarily disable RX skb allocation and URB submission when
the current error ratio is high, preventing us from trying to
allocate an infinite number of skbs. Reenable as soon as we
are finished processing the done queue, allowing the device
to continue working after short error bursts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 2a37b1a "MIPS: Netlogic: Move from u32 cpumask to cpumask_t"
breaks uniprocessor compilation on XLR with:
arch/mips/netlogic/xlr/setup.c: In function 'prom_init':
arch/mips/netlogic/xlr/setup.c:196:6: error: unused variable 'i'
Fix by defining 'i' only when CONFIG_SMP is defined.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4760/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The base address of the PCI memory is 0x10000000 and the base address of the
PCI configuration space is 0x17000000 on the AR71xx SoCs.
The AR71XX_PCI_MEM_SIZE is defined as 0x08000000 which is wrong because that
overlaps with the configuration space. This patch fixes the value of the
AR71XX_PCI_MEM_SIZE constant, in order to avoid this resource conflicts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4873/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The base address of the PCI memory is
0x10000000 and the base address of the
PCI configuration space is 0x14000000
on the AR724x SoCs.
The AR724X_PCI_MEM_SIZE is defined as
0x08000000 which is wrong because that
overlaps with the configuration space.
The patch fixes the value of the
AR724X_PCI_MEM_SIZE constant, in order
to avoid this resource conflicts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4872/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The introduction of the OF support broke the cp0_perfcount_irq mapping. This
resulted in oprofile not working anymore.
Offending commit is :
commit 3645da0276
Author: John Crispin <blogic@openwrt.org>
Date: Tue Apr 17 10:18:32 2012 +0200
OF: MIPS: lantiq: implement irq_domain support
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4875/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It has been reported that running this driver on some Samsung laptops
with EFI can cause those machines to become bricked as detailed in the
following report,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
There have also been reports of this driver causing Machine Check
Exceptions on recent EFI-enabled Samsung laptops,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
So disable it if booting from EFI since this driver relies on
grovelling around in the BIOS memory map which isn't going to work.
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
A scan request is split into multiple scan commands queued in
scan_pending_q. Each scan command will be sent to firmware and
its response is handlded one after another.
If any error is detected while parsing IE in command response
buffer the remaining data will be ignored and error is returned.
We should check if there is any more scan commands pending in
the queue before returning error. This ensures that we will call
cfg80211_scan_done if this is the last scan command, or send
next scan command in scan_pending_q to firmware.
Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G34+
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixlets from Borislav Petkov:
"Two minor correctness fixlets from Dan Carpenter and Joe Perches each."
* tag 'edac_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Fix kcalloc argument order
EDAC: Test correct variable in ->store function
- A collection of small ASoC driver fixes (error path fixes, register
correction, regulator bypass mode fix, etc)
- A few regression fixes and quirks of HD-audio (wrong page attributes
for SG-buffer, Poulsbo/Oaktrail controller fix, digital mic fix for
Acer, etc)
- A fix for USB-audio UAC2 devices wrt FU length check
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=mySP
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- A collection of small ASoC driver fixes (error path fixes, register
correction, regulator bypass mode fix, etc)
- A few regression fixes and quirks of HD-audio (wrong page attributes
for SG-buffer, Poulsbo/Oaktrail controller fix, digital mic fix for
Acer, etc)
- A fix for USB-audio UAC2 devices wrt FU length check
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix non-snoop page handling
ALSA: hda - Enable LPIB delay count for Poulsbo / Oaktrail
ALSA: hda - fix inverted internal mic on Acer AOA150/ZG5
ALSA: usb-audio: fix invalid length check for RME and other UAC 2 devices
ALSA: hda - Add a fixup for Packard-Bell desktop with ALC880
ASoC: wm_adsp: Release firmware on error
ASoC: wm_adsp: Use GFP_DMA for things that may be DMAed
ASoC: arizona: Use actual rather than desired BCLK when calculating LRCLK
ASoC: wm2200: correct mixer values and text
ASoC: MAINTAINERS: Update email address.
ASoC: wm5110: Correct AEC loopback mask
ASoC: wm5102: Correct AEC loopback mask
ASoC: dapm: Fix sense of regulator bypass mode
ASoC: fsl: fix multiple definition of init_module
ASoC: arizona: Disable free-running mode on FLL1
of_regulator_match() saves some dynamcially allocated state into the
match table that's passed to it. By implementation and not contract, for
each match table entry, if non-NULL state is already present,
of_regulator_match() will not overwrite it. of_regulator_match() is
typically called each time a regulator is probe()d. This means it is
called with the same match table over and over again if a regulator
triggers deferred probe. This results in stale, kfree()d data being left
in the match table from probe to probe, which causes a variety of crashes
or use of invalid data.
Explicitly free all output state from of_regulator_match() before
generating new results in order to avoid this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Pull drm fixes from Dave Airlie:
"Intel, radeon and exynos fixes. Nothing too major or wierd: one dmar
fix and a radeon cursor corruption, along with misc exynos fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (21 commits)
drm/exynos: add check for the device power status
drm/exynos: Make 'drm_hdmi_get_edid' static
drm/exynos: fimd and ipp are broken on multiplatform
drm/exynos: don't include plat/gpio-cfg.h
drm/exynos: Remove "internal" interrupt handling
drm/exynos: Add missing static specifiers in exynos_drm_rotator.c
drm/exynos: Replace mdelay with usleep_range
drm/exynos: Make ipp_handle_cmd_work static
drm/exynos: Make g2d_userptr_get_dma_addr static
drm/exynos: consider DMA_NONE flag to dmabuf import
drm/exynos: free sg object if dma_map_sg is failed
drm/exynos: added validation of edid for vidi connection
drm/exynos: let drm handle edid allocations
drm/radeon: Enable DMA_IB_SWAP_ENABLE on big endian hosts.
drm/radeon: fix a rare case of double kfree
radeon_display: Use pointer return error codes
drm/radeon: fix cursor corruption on DCE6 and newer
drm/i915: dump UTS_RELEASE into the error_state
iommu/intel: disable DMAR for g4x integrated gfx
drm/i915: GFX_MODE Flush TLB Invalidate Mode must be '1' for scanline waits
...
- fix return value when filesystem probe finds no XFS magic, a
regression introduced in 9802182.
- fix stack switch in __xfs_bmapi_allocate by moving the check for stack
switch up into xfs_bmapi_write.
- fix oops in _xfs_buf_find by validating that the requested block is
within the filesystem bounds.
- limit speculative preallocation near ENOSPC.
- fix an unmount hang in xfs_wait_buftarg by freeing the
xfs_buf_log_item in xfs_buf_item_unlock.
- fix a possible use after free with AIO.
- fix xfs_swap_extents after removal of xfs_flushinval_pages, a
regression introduced in fb59581404.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=wViN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-v3.8-rc6' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
"Here are fixes for returning EFSCORRUPTED on probe of a non-xfs
filesystem, the stack switch in xfs_bmapi_allocate, a crash in
_xfs_buf_find, speculative preallocation as the filesystem nears
ENOSPC, an unmount hang, a race with AIO, and a regression with
xfs_fsr:
- fix return value when filesystem probe finds no XFS magic, a
regression introduced in 9802182.
- fix stack switch in __xfs_bmapi_allocate by moving the check for
stack switch up into xfs_bmapi_write.
- fix oops in _xfs_buf_find by validating that the requested block is
within the filesystem bounds.
- limit speculative preallocation near ENOSPC.
- fix an unmount hang in xfs_wait_buftarg by freeing the
xfs_buf_log_item in xfs_buf_item_unlock.
- fix a possible use after free with AIO.
- fix xfs_swap_extents after removal of xfs_flushinval_pages, a
regression introduced in commit fb59581404a."
* tag 'for-linus-v3.8-rc6' of git://oss.sgi.com/xfs/xfs:
xfs: Fix xfs_swap_extents() after removal of xfs_flushinval_pages()
xfs: Fix possible use-after-free with AIO
xfs: fix shutdown hang on invalid inode during create
xfs: limit speculative prealloc near ENOSPC thresholds
xfs: fix _xfs_buf_find oops on blocks beyond the filesystem end
xfs: pull up stack_switch check into xfs_bmapi_write
xfs: Do not return EFSCORRUPTED when filesystem probe finds no XFS magic
Pull one s390 fix from Martin Schwidefsky:
"Another transparent huge page fix, we need to define a s390 variant
for pmdp_set_wrprotect to flush the TLB for the huge page correctly."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/thp: implement pmdp_set_wrprotect()
- Revert gpio request/free backend, new patch set
in the works, will be for v3.9. Get this old cruft
out before anyone hurts himself on it.
- Kconfig buzz
- Various compile warnings
- MPP6 value for the Kirkwood
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=itGu
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"This is a late pinctrl fix pull request, we had to revert out the
pinctrl-single GPIO backend, because of, well, design issues. We're
cooking a better thing for the next cycle.
- Revert gpio request/free backend, new patch set in the works, will
be for v3.9. Get this old cruft out before anyone hurts himself on
it.
- Kconfig buzz
- Various compile warnings
- MPP6 value for the Kirkwood"
* tag 'pinctrl-fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: nomadik: nmk_prcm_gpiocr_get_mode may be unused
pinctrl: exynos: don't mark probing functions as __init
Revert "pinctrl: single: support gpio request and free"
pinctrl: mvebu: fix MPP6 value for kirkwood driver
pinctrl: mvebu: Fix compiler warnings
pinctrl: pinctrl-mxs: Fix variables' definition type
pinctrl: samsung: removing duplicated condition for PINCTRL_SAMSUNG
This patch fixes a regression introduced in v3.8-rc1 code where a
zero-length READ_CAPACITY_16 was no longer returning GOOD status, but
instead returning TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE to generate
a CHECK_CONDITION status.
This regression was introduced with the following commit:
commit de103c93af
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
and this patch has been tested with the following zero-length CDB:
sg_raw /dev/sdd 9e 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCSI Status: Good
Sense Information:
sense buffer empty
Also, convert sbc_emulate_readcapacity() to follow the same method
of handling transport_kmap_data_sg() return values, but we never
expect a zero-length request here.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a regression introduced in v3.8-rc1 code where
a zero-length MODE_SENSE was no longer returning GOOD status, but
instead returning TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE to generate
a CHECK_CONDITION status.
This regression was introduced with the following commit:
commit de103c93af
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
and this patch has been tested with the following zero-length CDB:
sg_raw /dev/sdd 5a 00 0a 00 00 00 00 00 00 00
SCSI Status: Good
Sense Information:
sense buffer empty
Cc: Christoph Hellwig <hch@lst.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a minor regression introduced in v3.8-rc1 code
where a zero-length INQUIRY was no longer returning the correct
INVALID FIELD IN CDB additional sense code.
This regression was introduced with the following commit:
commit de103c93af
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
and this patch has been tested with the following zero-length CDB:
sg_raw /dev/sdd 12 00 83 00 00 00
SCSI Status: Check Condition
Sense Information:
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid field in cdb
Cc: Christoph Hellwig <hch@lst.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
nmk_prcm_gpiocr_get_mode is only needed for debugfs output at
the moment, which can be compile-time disabled. Marking
the function __maybe_unused still gives us compile-time
coverage, but avoids a gcc warning.
Without this patch, building nhk8815_defconfig results in:
drivers/pinctrl/pinctrl-nomadik.c:676:12: warning: 'nmk_prcm_gpiocr_get_mode' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Functions called from a driver probe() method must not be
marked __init, because they may get called after the
init phase is done, when the device shows up late, or
because of deferred probing.
Without this patch, building exynos_defconfig results in
multiple warnings like:
WARNING: drivers/pinctrl/built-in.o(.text+0x51bc): Section mismatch in reference from the function exynos5440_pinctrl_probe() to the function .init.text:exynos5440_gpiolib_register()
The function exynos5440_pinctrl_probe() references
the function __init exynos5440_gpiolib_register().
This is often because exynos5440_pinctrl_probe lacks a __init
annotation or the annotation of exynos5440_gpiolib_register is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
vmxnet3 fails to set netif_carrier_off on probe, meaning that when an interface
is opened the __LINK_STATE_NOCARRIER bit is already cleared, and so
/sys/class/net/<ifname>/operstate remains in the unknown state. Correct this by
setting netif_carrier_off on probe, like other drivers do.
Also, while we're at it, lets remove the netif_carrier_ok checks from the
link_state_update function, as that check is atomically contained within the
netif_carrier_[on|off] functions anyway
Tested successfully by myself
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: <stable@vger.kernel.org> # 3.5.x & 3.6.x
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bonding module is loaded with primary parameter and one decides to unset
primary slave using sysfs these settings are not preserved during bond device
restart. Primary slave is only unset once and it's not remembered in
bond->params structure. Below is example of recreation.
grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond0
BONDING_OPTS="mode=active-backup miimon=100 primary=eth01"
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)
echo "" > /sys/class/net/bond0/bonding/primary
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None
sed -i -e 's/primary=eth01//' /etc/sysconfig/network-scripts/ifcfg-bond0
grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond
BONDING_OPTS="mode=active-backup miimon=100 "
ifdown bond0 && ifup bond0
without patch:
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)
with patch:
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Milos Vyletel <milos.vyletel@sde.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We drop a connection request if the accept backlog is full and there are
sufficient packets in the syn queue to warrant starting drops. Increment the
appropriate counters so this isn't silent, for accurate stats and help in
debugging.
This patch assumes LINUX_MIB_LISTENDROPS is a superset of/includes the
counter LINUX_MIB_LISTENOVERFLOWS.
Signed-off-by: Nivedita Singhvi <niv@us.ibm.com>
Acked-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "Universal/Local" (U/L) bit must be complmented according to RFC4944
and RFC2464.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forbid polling, writing and reading when the file were detached, this may
complex the user in several cases:
- when guest pass some buffers to vhost/qemu and then disable some queues,
host/qemu needs to do its own cleanup on those buffers which is complex
sometimes. We can do this simply by allowing a user can still write to an
disabled queue. Write to an disabled queue will cause the packet pass to the
kernel and read will get nothing.
- align the polling behavior with macvtap which never fails when the queue is
created. This can simplify the polling errors handling of its user (e.g vhost)
We can simply achieve this by don't assign NULL to tfile->tun when detached.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the polling errors were ignored, which can lead following issues:
- vhost remove itself unconditionally from waitqueue when stopping the poll,
this may crash the kernel since the previous attempt of starting may fail to
add itself to the waitqueue
- userspace may think the backend were successfully set even when the polling
failed.
Solve this by:
- check poll->wqh before trying to remove from waitqueue
- report polling errors in vhost_poll_start(), tx_poll_start(), the return value
will be checked and returned when userspace want to set the backend
After this fix, there still could be a polling failure after backend is set, it
will addressed by the next patch.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when vhost_init_used() fails the sock refcnt and ubufs were
leaked. Correct this by calling vhost_init_used() before assign ubufs and
restore the oldsock when it fails.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Beulich
Alan Stern
Alim Akhtar
Linus Torvalds
Dave Airlie
Daniele Palmas
Marcelo Ricardo Leitner
Trond Myklebust
H. Peter Anvin
Bjørn Mork
Jayachandran C
Gabor Juhos
John Crispin
Matt Fleming
Bing Zhao
Mikko Tiihonen
Alex Deucher
Joe Perches
Dan Carpenter
Stephen Warren
Nicholas Bellinger
Arnd Bergmann
Neil Horman
Bruce Allan
Milos Vyletel
Nivedita Singhvi
YOSHIFUJI Hideaki / 吉藤英明
Sarveshwar Bandi
Jason Wang