Commit b4b55cda58 (Refine the way to release PCI IRQ resources)
introduced a regression in the PCI IRQ resource management by causing
the IRQ resource of a device, established when pci_enabled_device()
is called on a fully disabled device, to be released when the driver
is unbound from the device, regardless of the enable_cnt.
This leads to the situation that an ill-behaved driver can now make a
device unusable to subsequent drivers by an imbalance in their use of
pci_enable/disable_device(). That is a serious problem for secondary
drivers like vfio-pci, which are innocent of the transgressions of
the previous driver.
Since the solution of this problem is not immediate and requires
further discussion, revert commit b4b55cda58 and the issue it was
supposed to address (a bug related to xen-pciback) will be taken
care of in a different way going forward.
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some PCI device drivers assume that pci_dev->irq won't change after
calling pci_disable_device() and pci_enable_device() during suspend and
resume.
Commit c03b3b0738 ("x86, irq, mpparse: Release IOAPIC pin when
PCI device is disabled") frees PCI IRQ resources when pci_disable_device()
is called and reallocate IRQ resources when pci_enable_device() is
called again. This breaks above assumption. So commit 3eec595235
("x86, irq, PCI: Keep IRQ assignment for PCI devices during
suspend/hibernation") and 9eabc99a63 ("x86, irq, PCI: Keep IRQ
assignment for runtime power management") fix the issue by avoiding
freeing/reallocating IRQ resources during PCI device suspend/resume.
They achieve this by checking dev.power.is_prepared and
dev.power.runtime_status. PM maintainer, Rafael, then pointed out that
it's really an ugly fix which leaking PM internal state information to
IRQ subsystem.
Recently David Vrabel <david.vrabel@citrix.com> also reports an
regression in pciback driver caused by commit cffe0a2b5a ("x86, irq:
Keep balance of IOAPIC pin reference count"). Please refer to:
http://lkml.org/lkml/2015/1/14/546
So this patch refine the way to release PCI IRQ resources. Instead of
releasing PCI IRQ resources in pci_disable_device()/
pcibios_disable_device(), we now release it at driver unbinding
notification BUS_NOTIFY_UNBOUND_DRIVER. In other word, we only release
PCI IRQ resources when there's no driver bound to the PCI device, and
it keeps the assumption that pci_dev->irq won't through multiple
invocation of pci_enable_device()/pci_disable_device().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Xen pciback driver assumes that pci_dev->irq won't change after calling
pci_disable_device(). But commit cffe0a2b5a
("x86, irq: Keep balance of IOAPIC pin reference count") frees irq
resources and resets pci_dev->irq to zero when pci_disable_device() is
called.
So this is a hotfix for 3.19 to avoid resetting pci_dev->irq, and
another proper fix will be prepared for next merging window.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1421720467-7709-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
To keep balance of IOAPIC pin reference count, we need to protect
pirq_enable_irq(), acpi_pci_irq_enable() and intel_mid_pci_irq_enable()
from reentrance. There are two cases which will cause reentrance.
The first case is caused by suspend/hibernation. If pcibios_disable_irq
is called during suspending/hibernating, we don't release the assigned
IRQ number, otherwise it may break the suspend/hibernation. So late when
pcibios_enable_irq is called during resume, we shouldn't allocate IRQ
number again.
The second case is that function acpi_pci_irq_enable() may be called
twice for PCI devices present at boot time as below:
1) pci_acpi_init()
--> acpi_pci_irq_enable() if pci_routeirq is true
2) pci_enable_device()
--> pcibios_enable_device()
--> acpi_pci_irq_enable()
We can't kill kernel parameter pci_routeirq yet because it's still
needed for debugging purpose.
So flag irq_managed is introduced to track whether IRQ number is
assigned by OS and to protect pirq_enable_irq(), acpi_pci_irq_enable()
and intel_mid_pci_irq_enable() from reentrance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1414387308-27148-13-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the ACPI core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during runtime power
management, otherwise it may cause failure of device wakeups.
Commit 3eec595235 "x86, irq, PCI: Keep IRQ assignment for PCI
devices during suspend/hibernation" has fixed the issue for suspend/
hibernation, we also need the same fix for runtime device sleep too.
Fix: https://bugzilla.kernel.org/show_bug.cgi?id=83271
Reported-and-Tested-by: EmanueL Czirai <amanual@openmailbox.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: EmanueL Czirai <amanual@openmailbox.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409304383-18806-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during suspend/hibernation,
otherwise it may cause failure of suspend/hibernation due to:
1) Device driver calls pci_enable_device() to allocate an IRQ number
and register interrupt handler on the returned IRQ.
2) Device driver's suspend callback calls pci_disable_device() and
release assigned IRQ in turn.
3) Device driver's resume callback calls pci_enable_device() to
allocate IRQ number again. A different IRQ number may be assigned
by IOAPIC driver this time.
4) Now the hardware delivers interrupt to the new IRQ but interrupt
handler is still registered against the old IRQ, so it breaks
suspend/hibernation.
To fix this issue, we keep IRQ assignment during suspend/hibernation.
Flag pci_dev.dev.power.is_prepared is used to detect that
pci_disable_device() is called during suspend/hibernation.
Reported-and-Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1407478071-29399-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Release IOAPIC pin associated with PCI device when the PCI device
is disabled.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Link: http://lkml.kernel.org/r/1402380987-32577-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This commit moves ISA-specific code to separate function and makes that
function depend on CONFIG_{E}ISA so that we do not have to maintain
acpi_isa_irq_to_gsi() function for architectures which do not support ISA.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_pci_link_allocate_irq() can return negative gsi even if
entry != NULL. For that case we have a memory leak, so free
entry before returning from acpi_pci_irq_enable() for gsi < 0.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously, we cached _PRT (PCI routing table, ACPI 5.0 sec 6.2.12)
contents and associated each _PRT entry with a PCI bus number. The bus
number association means dependencies on PCI device enumeration and bus
number assignment, as well as on the PCI/ACPI binding process.
After 4f535093cf ("PCI: Put pci_dev in device tree as early as possible"),
these dependencies caused the IRQ issues reported by Peter:
pci 0000:00:1e.0: PCI bridge to [bus 09] (subtractive decode)
pci 0000:00:1e.0: can't derive routing for PCI INT A
snd_ctxfi 0000:09:02.0: PCI INT A: no GSI - using ISA IRQ 5
irq 18: nobody cared (try booting with the "irqpoll" option)
This patch removes _PRT caching. Instead, we evaluate _PRT as needed
in the pci_enable_device() path. This also removes the dependency on
PCI bus numbers: we can simply look at the _PRT associated with each
bridge as we walk upstream toward the root.
[bhelgaas: changelog]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=53561
Reported-and-tested-by: Peter Hurley <peter@hurleysoftware.com>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
* acpi-general: (38 commits)
ACPI / thermal: _TMP and _CRT/_HOT/_PSV/_ACx dependency fix
ACPI: drop unnecessary local variable from acpi_system_write_wakeup_device()
ACPI: Fix logging when no pci_irq is allocated
ACPI: Update Dock hotplug error messages
ACPI: Update Container hotplug error messages
ACPI: Update Memory hotplug error messages
ACPI: Update CPU hotplug error messages
ACPI: Add acpi_handle_<level>() interfaces
ACPI: remove use of __devexit
ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.
ACPI / battery: Correct battery capacity values on Thinkpads
Revert "ACPI / x86: Add quirk for "CheckPoint P-20-00" to not use bridge _CRS_ info"
ACPI: create _SUN sysfs file
ACPI / memhotplug: bind the memory device when the driver is being loaded
ACPI / memhotplug: don't allow to eject the memory device if it is being used
ACPI / memhotplug: free memory device if acpi_memory_enable_device() failed
ACPI / memhotplug: fix memory leak when memory device is unbound from acpi_memhotplug
ACPI / memhotplug: deal with eject request in hotplug queue
ACPI / memory-hotplug: add memory offline code to acpi_memory_device_remove()
ACPI / memory-hotplug: call acpi_bus_trim() to remove memory device
...
Conflicts:
include/linux/acpi.h (two additions at the end of the same file)
Work around a defect in the printk subsystem introduced by a
logging change.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These functions might be called from modules as well so make sure
they are exported.
In addition, implement empty version of acpi_unregister_gsi() and
remove the one from pci_irq.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This effectively reverts 859a3f86ca ("ACPI: simplify
acpi_pci_irq_add_prt() API") and d9efae3688 ("ACPI: simplify
acpi_pci_irq_del_prt() API").
The reason is to disentangle these routines from the struct pci_bus.
We want to be able to add the _PRT before the struct pci_bus
exists, and delete the _PRT after we've removed the pci_bus.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
When the runtime PM is activated on PCI, if a device switches state
frequently (e.g. an EHCI controller with autosuspending USB devices
connected) the PCI configuration traces might be very verbose in the
kernel log. Let's guard those traces with DEBUG condition.
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The following was observed by Steve Rostedt on 3.0.0-rc5
Backtrace:
irq 16: nobody cared (try booting with the "irqpoll" option)
Pid: 65, comm: irq/16-uhci_hcd Not tainted 3.0.0-rc5-test+ #94
Call Trace:
[<ffffffff810aa643>] __report_bad_irq+0x37/0xc1
[<ffffffff810aaa2d>] note_interrupt+0x14e/0x1c9
[<ffffffff810a9a05>] ? irq_thread_fn+0x3c/0x3c
[<ffffffff810a990e>] irq_thread+0xf6/0x1b1
[<ffffffff810a9818>] ? irq_finalize_oneshot+0xb3/0xb3
[<ffffffff8106b4d6>] kthread+0x9f/0xa7
[<ffffffff814f1f04>] kernel_thread_helper+0x4/0x10
[<ffffffff8103ca09>] ? finish_task_switch+0x7b/0xc0
[<ffffffff814eac78>] ? retint_restore_args+0x13/0x13
[<ffffffff8106b437>] ? __init_kthread_worker+0x5a/0x5a
[<ffffffff814f1f00>] ? gs_change+0x13/0x13
handlers:
[<ffffffff810a912d>] irq_default_primary_handler threaded [<ffffffff8135eaa6>] usb_hcd_irq
[<ffffffff810a912d>] irq_default_primary_handler threaded [<ffffffff8135eaa6>] usb_hcd_irq
Disabling IRQ #16
The problem being that a device triggers boot interrupts (due to threaded
interrupt handling and masking of the IO-APIC), which are forwarded
to the PIRQ line of the device. These interrupts are not handled on the PIRQ
line because the interrupt handler is not present there.
This should have already been fixed by CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS.
However some parts of the quirk got lost in the ACPI merge. This is a resent of
the patch proposed in 2009.
See http://lkml.org/lkml/2009/9/7/192
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Strictly speaking on x86 (where acpi is used) dev->irq must be
a dual i8259 irq input aka an isa irq. Therefore we should translate
that isa irq into a gsi before passing it to a function that
takes a gsi.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-3-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
There is no need to pass a segment/bus tuple to this API, as the callsite
always has a struct pci_bus. We can derive segment/bus from the
struct pci_bus, so let's take this opportunit to simplify the API and
make life easier for the callers.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A PCI domain cannot change as you descend down subordinate buses, which
makes the 'segment' argument to acpi_pci_irq_add_prt() useless.
Change the interface to take a struct pci_bus *, from whence we can derive
the bus number and segment. Reducing the number of arguments makes life
simpler for callers.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We want to use dev_to_node() later on, to be aware of the 'home node'
of the GSI in question.
[ Impact: cleanup, prepare the IRQ code to be more NUMA aware ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
LKML-Reference: <49F65560.20904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the generic pci_swizzle_interrupt_pin() instead of ACPI-specific code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes function declarations consistent throughout
the file and removes some unnecessary initializations.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_pci_allocate_irq() and acpi_pci_free_irq() are trivial and
only used once, so just open-code them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't need a struct containing a count and a list_head; a simple
list_head is sufficient. The list iterators handle empty lists
fine.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This folds acpi_pci_irq_derive() into acpi_pci_irq_lookup() so it
can be easily used by both acpi_pci_irq_enable() and acpi_pci_irq_disable().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No functional change; this just uses the typical pattern of
PCI INTx swizzling done on other architectures.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This doesn't change anything functionally; it just changes tests
so we test for success instead of failure. This makes the code
read more easily and allows us to remove the "!entry" in the while
loop condition.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We currently pass a callback function (either acpi_pci_allocate_irq() or
acpi_pci_free_irq()) to acpi_pci_irq_lookup() and acpi_pci_irq_derive().
I think it's simpler to remove the callback and just have the enable/
disable functions make the calls directly.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Print one message (either "found" or "not found") for every _PRT
search. And add pin information to the INTx swizzling debug.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There's no reason to pass around segment, bus, and device independently
when we can just pass the pci_dev pointer, which carries all those
already.
The pci_dev contains an interrupt pin, too, but we still have to pass both
the pci_dev and the pin because when we use a bridge to derive an IRQ, we
need the pin from the downstream device, not the bridge.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the PCI INTx pin encoding (1=INTA, 2=INTB, etc) for _PRT quirks.
Then we can simply compare "entry->pin == quirk->pin".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch changes pci_irq.c to always use PCI INTx pin encodings
instead of a mix of PCI and _PRT encodings.
The PCI INTx pin numbers from the PCI_INTERRUPT_PIN config register
are 0=device doesn't use interrupts, 1=INTA, ..., 4=INTD. But the
_PRT table uses 0=INTA, ..., 3=INTD.
This patch converts the _PRT encoding to the PCI encoding immediately
when we add a _PRT entry to the global list. All the rest of the
code can then use the PCI encoding consistently.
The point of this is to make the interrupt swizzling look the same
as on other architectures, so someday we can unify them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This adds a helper function to convert INTx pin numbers from the _PRT
(0, 1, 2, 3) to the pin name ('A', 'B', 'C', 'D').
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The struct acpi_prt_entry is used only in pci_irq.c, so there's no
need for the declaration to be public. This patch moves it into
pci_irq.c.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The interrupt numbers from _PRT entries are GSIs, not Linux IRQs.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_PRT entries don't contain any useful PCI function information (the
function part of the PCI address is supposed to be 0xffff), and we
don't ever look at it, so this patch just removes the reference to
it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, acpi_pci_irq_add_prt() did all its own buffer management.
But now that we have ACPI_ALLOCATE_BUFFER, we no longer need to do
that management. And we don't have to call acpi_get_irq_routing_table()
twice (once to learn the size of the buffer needed, and again to
actually get the table).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Better to oops and learn about a bug than to silently cover it up.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rafael J. Wysocki
Jiang Liu
Linus Torvalds
Tomasz Nowicki
Lv Zheng
Yinghai Lu
Joe Perches
Andy Shevchenko
Bjorn Helgaas
Vincent Palatin
Stefan Assmann
Zhang Rui
Eric W. Biederman
Tejun Heo
Len Brown
Alexander Chiang
Jan Beulich
Bjorn Helgaas