Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the bit_offset in the cell is zero, the pointer to the msb will
not be properly initialized (ie, will still be pointing to the first
byte in the buffer).
This being the case, if there are bits to clear in the msb, those will
be left untouched while the mask will incorrectly clear bit positions
on the first byte.
This commit also makes sure that any byte unused in the cell is
cleared.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add nvmem_cell_read_u16() helper to ease read of an u16 value on consumer
side. This is inspired by nvmem_cell_read_u32() function.
This helper is useful on stm32 that has 16 bits data cells stored in non
volatile memory.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On STM32MP15, OTP area may be read/written by using BSEC (boot, security
and OTP control). BSEC registers set is composed of various regions, among
which control registers and OTP shadow registers.
Secure monitor calls are involved in this process to allow (or deny)
access to the full range of OTP data.
This adds support for reading and writing OTP data using SMC services.
Data content can be aligned on 16-bits or 8-bits. Then take care of it,
since BSEC data is 32-bits wide.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device tree binding already lists compatible strings for these two
SoCs. They don't have the defect as seen on the H3, and the size and
register layout is the same as the A64. Furthermore, the driver does
not include nvmem cell definitions.
Add support for these two compatible strings, re-using the config for
the A64.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally the SID e-fuses were thought to be in big-endian format.
Later sources show that they are in fact native or little-endian.
The most compelling evidence is the thermal sensor calibration data,
which is a set of one to three 16-bit values. In native-endian they
are in 16-bit cells with increasing offsets, whereas with big-endian
they are in the wrong order, and a gap with no data will show if there
are one or three cells.
Switch to a native endian representation for the nvmem device. For the
H3, the register read-out method was already returning data in native
endian. This only affects the other SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi_sid driver currently uses a statically allocated nvmem_config
structure that is updated at probe time. This is sub-optimal as it
limits the driver to one instance, and also takes up space even if the
device is not present.
Modify the driver to allocate the nvmem_config structure at probe time,
plugging in the desired parameters along the way.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SID cells are 32-bit aligned, and a multiple of 32 bits in length. The
only outlier is the thermal sensor calibration data, which is 16 bits
per sensor. However a whole 64 bits is allocated for this purpose, so
we could consider it conforming to the rule above.
Also, the register read-out method assumes native endian, unlike the
direct MMIO method, which assumes big endian. Thus no endian conversion
is involved.
Under these assumptions, the register read-out method can be slightly
optimized. Instead of reading one word then discarding 3 bytes, read
the whole word directly into the buffer. However, for reads under 4
bytes or trailing bytes, we still use a scratch buffer to extract the
requested bytes.
We could go one step further if .word_size was 4, but changing that
would affect the sysfs interface's behavior.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the reg_read callbacks already support arbitrary, but 4-byte
aligned. offsets and lengths into the SID, there is no need for another
for loop just to use it to read 1 byte at a time.
Read out the whole SID block in one go.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX OCOTP controller is used in numerous Freescale/NXP
SoCs from the MXC family, so the strict dependency on the
i.MX6 SoC is too narrow. Broaden it to cover all the MXC
familiy members.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX8MQ uses the same OCOTP block as the i.MX7D, but with
fourfold increase in fuse banks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/parport/ieee1284.c: In function ‘parport_read’:
drivers/parport/ieee1284.c:722:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (parport_negotiate (port, IEEE1284_MODE_NIBBLE)) {
^
drivers/parport/ieee1284.c:726:2: note: here
case IEEE1284_MODE_NIBBLE:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have success in 'Channel Access Write' but reading back latch
states fails, a write is retried without doing a proper slave reset.
This leads to protocol errors as the slave treats the next 'Channel
Access Write' as the continuation of previous command.
This commit is fixing this by making sure if the retry loop re-runs, a
reset is performed, whatever the failure (CONFIRM_BYTE or the read
back).
The loop was quite due for a cleanup and this change mandated it. By
isolating the CONFIG_W1_SLAVE_DS2408_READBACK case into it's own
function, we vastly reduce the visual and branching(runtime and
compile-time) noise.
Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Tested-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some tiny patches for the 5.2-rc1 merge window:
- Add linux-pm@ as a mailing list for the interconnect API.
- Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
-----BEGIN PGP SIGNATURE-----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=B5EN
-----END PGP SIGNATURE-----
Merge tag 'icc-5.2-rc1' of https://git.linaro.org/people/georgi.djakov/linux into char-misc-next
Georgi writes:
interconnect: for 5.2
Here are some tiny patches for the 5.2-rc1 merge window:
- Add linux-pm@ as a mailing list for the interconnect API.
- Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.2-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
interconnect: convert to DEFINE_SHOW_ATTRIBUTE
MAINTAINERS: Add mailing list for the interconnect API
Expose mei device state to user-space through sysfs.
This gives indication to applications that driver is in transition,
usefully mostly to detect link reset state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mei/hdcp module have its own Makefile
so naturally it should have associated Kconfig
in the same directory.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ASPEED AST2400, and AST2500 in some configurations include a
PCI-to-AHB MMIO bridge. This bridge allows a server to read and write
in the BMC's physical address space. This feature is especially useful
when using this bridge to send large files to the BMC.
The host may use this to send down a firmware image by staging data at a
specific memory address, and in a coordinated effort with the BMC's
software stack and kernel, transmit the bytes.
This driver enables the BMC to unlock the PCI bridge on demand, and
configure it via ioctl to allow the host to write bytes to an agreed
upon location. In the primary use-case, the region to use is known
apriori on the BMC, and the host requests this information. Once this
request is received, the BMC's software stack will enable the bridge and
the region and then using some software flow control (possibly via IPMI
packets), copy the bytes down. Once the process is complete, the BMC
will disable the bridge and unset any region involved.
The default behavior of this bridge when present is: enabled and all
regions marked read-write. This driver will fix the regions to be
read-only and then disable the bridge entirely.
The memory regions protected are:
* BMC flash MMIO window
* System flash MMIO windows
* SOC IO (peripheral MMIO)
* DRAM
The DRAM region itself is all of DRAM and cannot be further specified.
Once the PCI bridge is enabled, the host can read all of DRAM, and if
the DRAM section is write-enabled, then it can write to all of it.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the ast2400, ast2500 PCI-to-AHB bridge control driver bindings.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Highlights include:
Bugfixes:
- Fix a regression in which an RPC call can be tagged with an error despite
the transmission being successful
-----BEGIN PGP SIGNATURE-----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=3T3x
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfix from Trond Myklebust:
"Fix a regression in which an RPC call can be tagged with an error
despite the transmission being successful"
* tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Ignore queue transmission errors on successful transmission
Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXLtrDSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYh/AQDe6Jf7
jU/VKsir8r74Uy1gHw9wXkmcgzKeTzHErEyvGgD9HqEfAKUWr0YlMqfKqnQZUhUc
TPokv5u1u2xc/ba+nuo=
=VutB
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: aic7xxx: fix EISA support
Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
scsi: core: set result when the command cannot be dispatched
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAly7HukQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpla6D/9y7YyAyKDgv/pVQgAlDYaGSXufvrK5iK/f
uFdSWPvGuWMbx+xy/4hfSX1pV9ZRv1aRJeFOkL/qVyr+4izKrgevwj+6Kl3/mCUO
dhiqF76bnaGXNQC6YDn1IgZp2Za+WGpeNlEhwcg20Ve11U7DVBhcL/n/6NYphtUG
V7ZFoVw+yjOO9GvkUeHx24HIQdC0JrABMoXYldl/tX3H9WjB3d1ncZDS45TuemXJ
lwm/S4nyaNaDzLnO7Hv51u3tCFpuaJbcgBdKuZB/oSWhU68D26/6peW+8qAvN+ec
htibFrK6KPRQCLNMEaV2njZEyprkL/BZJz4YukwmWB8GAtsuquy3Q3wJPounGmm5
7fCG/T1asqkurwhVcHOC07R6+d8AT5ARyJn3QYFmoYCIoSwObu6xhZHHAv7Ct1Xn
lrU4it0WkYbTXVI1l4CaRUtshCIQTZwr2EsgppjAsBc1+V2KgtbxR1wkQq2q9tQZ
Fa/2KTv9Y1+7FUOf09LEvTbuUgZn4I6u4E07QwY4miFsQSEUufirfHZ5t62lIgA9
3YzUrlVQSP1PbG8IP4aCSX2o+dxhL1Js6ukdZAxM6w9RtjLqWI3zTImSSMJobjna
SF53kkpv1xuJYT+Z1YmNGbMauzLs/HhCB9ww56TUuQYW/rTDASqFc48l7+vsfPrZ
sTEkShVGOw==
=d9Ws
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190420' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of small fixes that should go into this series. This contains:
- Removal of unused queue member (Hou)
- Overflow bvec fix (Ming)
- Various little io_uring tweaks (me)
- kthread parking
- Only call cpu_possible() for verified CPU
- Drop unused 'file' argument to io_file_put()
- io_uring_enter vs io_uring_register deadlock fix
- CQ overflow fix
- BFQ internal depth update fix (me)"
* tag 'for-linus-20190420' of git://git.kernel.dk/linux-block:
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
io_uring: fix CQ overflow condition
io_uring: fix possible deadlock between io_uring_{enter,register}
io_uring: drop io_file_put() 'file' argument
bfq: update internal depth state when queue depth changes
io_uring: only test SQPOLL cpu after we've verified it
io_uring: park SQPOLL thread if it's percpu
- Fix the disable controller logic in the designware driver
- Fix I3C entry in MAINTAINERS
-----BEGIN PGP SIGNATURE-----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=RUzG
-----END PGP SIGNATURE-----
Merge tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pill i3c fixes from Boris Brezillon:
- fix the random PID check
- fix the disable controller logic in the designware driver
- fix I3C entry in MAINTAINERS
* tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
MAINTAINERS: Fix the I3C entry
i3c: dw: Fix dw_i3c_master_disable controller by using correct mask
i3c: Fix the verification of random PID
Two core fixes for long-standing bugs for the races at concurrent
device creation and deletion that were (unsurprisingly) spotted by
syzkaller with usb-fuzzer. The rest are usual small HD-audio fixes.
-----BEGIN PGP SIGNATURE-----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=kpz9
-----END PGP SIGNATURE-----
Merge tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Two core fixes for long-standing bugs for the races at concurrent
device creation and deletion that were (unsurprisingly) spotted by
syzkaller with usb-fuzzer.
The rest are usual small HD-audio fixes"
* tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - add two more pin configuration sets to quirk table
ALSA: core: Fix card races between register and disconnect
ALSA: info: Fix racy addition/deletion of nodes
ALSA: hda: Initialize power_state field properly
Pull perf fixes from Ingo Molnar:
"Misc fixes:
- various tooling fixes
- kretprobe fixes
- kprobes annotation fixes
- kprobes error checking fix
- fix the default events for AMD Family 17h CPUs
- PEBS fix
- AUX record fix
- address filtering fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Avoid kretprobe recursion bug
kprobes: Mark ftrace mcount handler functions nokprobe
x86/kprobes: Verify stack frame on kretprobe
perf/x86/amd: Add event map for AMD Family 17h
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_btf()
perf tools: Fix map reference counting
perf evlist: Fix side band thread draining
perf tools: Check maps for bpf programs
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_bpf_prog_info()
tools include uapi: Sync sound/asound.h copy
perf top: Always sample time to satisfy needs of use of ordered queuing
perf evsel: Use hweight64() instead of hweight_long(attr.sample_regs_user)
tools lib traceevent: Fix missing equality check for strcmp
perf stat: Disable DIR_FORMAT feature for 'perf stat record'
perf scripts python: export-to-sqlite.py: Fix use of parent_id in calls_view
perf header: Fix lock/unlock imbalances when processing BPF/BTF info
perf/x86: Fix incorrect PEBS_REGS
perf/ring_buffer: Fix AUX record suppression
perf/core: Fix the address filtering fix
kprobes: Fix error check when reusing optimized probes
Pull x86 fixes from Ingo Molnar:
"Misc fixes all over the place: a console spam fix, section attributes
fixes, a KASLR fix, a TLB stack-variable alignment fix, a reboot
quirk, boot options related warnings fix, an LTO fix, a deadlock fix
and an RDT fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
x86/cpu/bugs: Use __initconst for 'const' init data
x86/mm/KASLR: Fix the size of the direct mapping section
x86/Kconfig: Fix spelling mistake "effectivness" -> "effectiveness"
x86/mm/tlb: Revert "x86/mm: Align TLB invalidation info"
x86/reboot, efi: Use EFI reboot for Acer TravelMate X514-51T
x86/mm: Prevent bogus warnings with "noexec=off"
x86/build/lto: Fix truncated .bss with -fdata-sections
x86/speculation: Prevent deadlock on ssb_state::lock
x86/resctrl: Do not repeat rdtgroup mode initialization
Pull scheduler fixes from Ingo Molnar:
"A deadline scheduler warning/race fix, and a cfs_period_us quota
calculation workaround where the real fix looks too involved to merge
immediately"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Correctly handle active 0-lag timers
sched/fair: Limit sched_cfs_period_timer() loop to avoid hard lockup
Pull locking fixes from Ingo Molnar:
"A lockdep warning fix and a script execution fix when atomics are
generated"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/atomics: Don't assume that scripts are executable
locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again
Pull cgroup fix from Tejun Heo:
"A patch to fix a RCU imbalance error in the devices cgroup
configuration error path"
* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: fix RCU imbalance in error case
Pull percpu fixlet from Dennis Zhou:
"This stops printing the base address of percpu memory on
initialization"
* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
percpu: stop printing kernel addresses
Here are 5 small fixes for some tty/serial/vt issues that have been
reported.
The vt one has been around for a while, it is good to finally get that
resolved. The others fix a build warning that showed up in 5.1-rc1, and
resolve a problem in the sh-sci driver.
Note, the second patch for build warning fix for the sc16is7xx driver
was just applied to the tree, as it resolves a problem with the previous
patch to try to solve the issue. It has not shown up in linux-next yet,
unlike all of the other patches, but it has passed 0-day testing and
everyone seems to agree that it is correct.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXLoeMg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yll3gCfdfclnKAQt7UnXUZccT7f6oebB6gAoLEy0NEi
lDl7inafWImRKCRq1+zw
=Qk9s
-----END PGP SIGNATURE-----
Merge tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are five small fixes for some tty/serial/vt issues that have been
reported.
The vt one has been around for a while, it is good to finally get that
resolved. The others fix a build warning that showed up in 5.1-rc1,
and resolve a problem in the sh-sci driver.
Note, the second patch for build warning fix for the sc16is7xx driver
was just applied to the tree, as it resolves a problem with the
previous patch to try to solve the issue. It has not shown up in
linux-next yet, unlike all of the other patches, but it has passed
0-day testing and everyone seems to agree that it is correct"
* tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: put err_spi and err_i2c into correct #ifdef
vt: fix cursor when clearing the screen
sc16is7xx: move label 'err_spi' to correct section
serial: sh-sci: Fix HSCIF RX sampling point adjustment
serial: sh-sci: Fix HSCIF RX sampling point calculation
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
Here is a bunch of IIO driver fixes, and some smaller staging driver
fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
all resolve a number of reported issues and have been in linux-next for
a few weeks with no reported issues.
The other staging driver fixes are all tiny, resolving some reported
issues in the comedi and most drivers, as well as some erofs fixes.
All of these patches have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXLm7QA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylqDgCgwt+6SUTrkHCrwfiSEIyY0gXBnZsAoKrNjd1Y
VvbBiG9lk0ST1V/vWrkJ
=Njex
-----END PGP SIGNATURE-----
Merge tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here is a bunch of IIO driver fixes, and some smaller staging driver
fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
all resolve a number of reported issues and have been in linux-next
for a few weeks with no reported issues.
The other staging driver fixes are all tiny, resolving some reported
issues in the comedi and most drivers, as well as some erofs fixes.
All of these patches have been in linux-next with no reported issues"
* tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
staging: comedi: ni_usb6501: Fix use of uninitialized mutex
staging: erofs: fix unexpected out-of-bound data access
staging: comedi: vmk80xx: Fix possible double-free of ->usb_rx_buf
staging: comedi: vmk80xx: Fix use of uninitialized semaphore
staging: most: core: use device description as name
iio: core: fix a possible circular locking dependency
iio: ad_sigma_delta: select channel when reading register
iio: pms7003: select IIO_TRIGGERED_BUFFER
iio: cros_ec: Fix the maths for gyro scale calculation
iio: adc: xilinx: prevent touching unclocked h/w on remove
iio: adc: xilinx: fix potential use-after-free on probe
iio: adc: xilinx: fix potential use-after-free on remove
iio: dac: mcp4725: add missing powerdown bits in store eeprom
io: accel: kxcjk1013: restore the range after resume.
iio:chemical:bme680: Fix SPI read interface
iio:chemical:bme680: Fix, report temperature in millidegrees
iio: chemical: fix missing Kconfig block for sgp30
iio: adc: at91: disable adc channel interrupt in timeout case
iio: gyro: mpu3050: fix chip ID reading
...
Here are 4 small misc driver fixes for 5.1-rc6.
Nothing major at all, they fix up a Kconfig issues, a SPDX invalid
license tag, and 2 tiny bugfixes.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXLm6yw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBXQCgok0WblimRO9jTDQul7JXTxwZyxMAoMU841gi
WPjtj2t1aqbxn8IdJPP/
=bIbF
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are four small misc driver fixes for 5.1-rc6.
Nothing major at all, they fix up a Kconfig issues, a SPDX invalid
license tag, and two tiny bugfixes.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
drivers: power: supply: goldfish_battery: Fix bogus SPDX identifier
extcon: ptn5150: fix COMPILE_TEST dependencies
misc: fastrpc: add checked value for dma_set_mask
habanalabs: remove low credit limit of DMA #0
bvec->bv_offset may be bigger than PAGE_SIZE sometimes, such as,
when one bio is splitted in the middle of one bvec via bio_split(),
and bi_iter.bi_bvec_done is used to build offset of the 1st bvec of
remained bio. And the remained bio's bvec may be re-submitted to fs
layer via ITER_IBVEC, such as loop and nvme-loop.
So we have to make sure that every bvec's offset is less than
PAGE_SIZE from bio_for_each_segment_all() because some drivers(loop,
nvme-loop) passes the splitted bvec to fs layer via ITER_BVEC.
This patch fixes this issue reported by Zhang Yi When running nvme/011.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yi Zhang <yi.zhang@redhat.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 6dc4f100c1 ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
all_q_node has not been used since commit 4b855ad371 ("blk-mq: Create
hctx for each present CPU"), so remove it.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull input updates from Dmitry Torokhov:
- several new key mappings for HID
- a host of new ACPI IDs used to identify Elan touchpads in Lenovo
laptops
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: snvs_pwrkey - initialize necessary driver data before enabling IRQ
HID: input: add mapping for "Toggle Display" key
HID: input: add mapping for "Full Screen" key
HID: input: add mapping for keyboard Brightness Up/Down/Toggle keys
HID: input: add mapping for Expose/Overview key
HID: input: fix mapping of aspect ratio key
[media] doc-rst: switch to new names for Full Screen/Aspect keys
Input: document meanings of KEY_SCREEN and KEY_ZOOM
Input: elan_i2c - add hardware ID for multiple Lenovo laptops
The "ENERGY_PERF_BIAS: Set to 'normal', was 'performance'" message triggers
on pretty much every Intel machine. The purpose of log messages with
a warning level is to notify the user of something which potentially is
a problem, or at least somewhat unexpected.
This message clearly does not match those criteria, so lower its log
priority from warning to info.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181230172715.17469-1-hdegoede@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
perf top:
Jiri Olsa:
- Fix 'perf top --pid', it needs PERF_SAMPLE_TIME since we switched to using
a different thread to sort the events and then even for just a single
thread we now need timestamps.
BPF:
Jiri Olsa:
- Fix bpf_prog and btf lookup functions failure path to to properly return
NULL.
- Fix side band thread draining, used to process PERF_RECORD_BPF_EVENT
metadata records.
core:
Jiri Olsa:
- Fix map lookup by name to get a refcount when the name is already in
the tree. Found
Song Liu:
- Fix __map__is_kmodule() by taking into account recently added BPF
maps.
UAPI:
Arnaldo Carvalho de Melo:
- Sync sound/asound.h copy
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXLm+cgAKCRCyPKLppCJ+
J7QCAQCtI0NIeLUKY/o0vITBvCeKi5R1NNkE/A8ZhTzWD9UApwEA0eqoNHsOmIUG
tFRCYi3hPByvtgjIRXvrCm0gpUfFdAo=
=/siq
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-5.1-20190419' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf top:
Jiri Olsa:
- Fix 'perf top --pid', it needs PERF_SAMPLE_TIME since we switched to using
a different thread to sort the events and then even for just a single
thread we now need timestamps.
BPF:
Jiri Olsa:
- Fix bpf_prog and btf lookup functions failure path to to properly return
NULL.
- Fix side band thread draining, used to process PERF_RECORD_BPF_EVENT
metadata records.
core:
Jiri Olsa:
- Fix map lookup by name to get a refcount when the name is already in
the tree. Found
Song Liu:
- Fix __map__is_kmodule() by taking into account recently added BPF
maps.
UAPI:
Arnaldo Carvalho de Melo:
- Sync sound/asound.h copy
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The core dumping code has always run without holding the mmap_sem for
writing, despite that is the only way to ensure that the entire vma
layout will not change from under it. Only using some signal
serialization on the processes belonging to the mm is not nearly enough.
This was pointed out earlier. For example in Hugh's post from Jul 2017:
https://lkml.kernel.org/r/alpine.LSU.2.11.1707191716030.2055@eggly.anvils
"Not strictly relevant here, but a related note: I was very surprised
to discover, only quite recently, how handle_mm_fault() may be called
without down_read(mmap_sem) - when core dumping. That seems a
misguided optimization to me, which would also be nice to correct"
In particular because the growsdown and growsup can move the
vm_start/vm_end the various loops the core dump does around the vma will
not be consistent if page faults can happen concurrently.
Pretty much all users calling mmget_not_zero()/get_task_mm() and then
taking the mmap_sem had the potential to introduce unexpected side
effects in the core dumping code.
Adding mmap_sem for writing around the ->core_dump invocation is a
viable long term fix, but it requires removing all copy user and page
faults and to replace them with get_dump_page() for all binary formats
which is not suitable as a short term fix.
For the time being this solution manually covers the places that can
confuse the core dump either by altering the vma layout or the vma flags
while it runs. Once ->core_dump runs under mmap_sem for writing the
function mmget_still_valid() can be dropped.
Allowing mmap_sem protected sections to run in parallel with the
coredump provides some minor parallelism advantage to the swapoff code
(which seems to be safe enough by never mangling any vma field and can
keep doing swapins in parallel to the core dumping) and to some other
corner case.
In order to facilitate the backporting I added "Fixes: 86039bd3b4e6"
however the side effect of this same race condition in /proc/pid/mem
should be reproducible since before 2.6.12-rc2 so I couldn't add any
other "Fixes:" because there's no hash beyond the git genesis commit.
Because find_extend_vma() is the only location outside of the process
context that could modify the "mm" structures under mmap_sem for
reading, by adding the mmget_still_valid() check to it, all other cases
that take the mmap_sem for reading don't need the new check after
mmget_not_zero()/get_task_mm(). The expand_stack() in page fault
context also doesn't need the new check, because all tasks under core
dumping are frozen.
Link: http://lkml.kernel.org/r/20190325224949.11068-1-aarcange@redhat.com
Fixes: 86039bd3b4 ("userfaultfd: add new syscall to provide memory externalization")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Jann Horn <jannh@google.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only references outside of the #ifdef have been removed, so now we
get a warning in non-SMP configurations:
mm/kmemleak.c:1404:13: error: unused function 'scan_large_block' [-Werror,-Wunused-function]
Add a new #ifdef around it.
Link: http://lkml.kernel.org/r/20190416123148.3502045-1-arnd@arndb.de
Fixes: 298a32b132 ("kmemleak: powerpc: skip scanning holes in the .bss section")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a module option, or core kernel argument, toggles a static-key it
requires jump labels to be initialized early. While x86, PowerPC, and
ARM64 arrange for jump_label_init() to be called before parse_args(),
ARM does not.
Kernel command line: rdinit=/sbin/init page_alloc.shuffle=1 panic=-1 console=ttyAMA0,115200 page_alloc.shuffle=1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ./include/linux/jump_label.h:303
page_alloc_shuffle+0x12c/0x1ac
static_key_enable(): static key 'page_alloc_shuffle_key+0x0/0x4' used
before call to jump_label_init()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted
5.1.0-rc4-next-20190410-00003-g3367c36ce744 #1
Hardware name: ARM Integrator/CP (Device Tree)
[<c0011c68>] (unwind_backtrace) from [<c000ec48>] (show_stack+0x10/0x18)
[<c000ec48>] (show_stack) from [<c07e9710>] (dump_stack+0x18/0x24)
[<c07e9710>] (dump_stack) from [<c001bb1c>] (__warn+0xe0/0x108)
[<c001bb1c>] (__warn) from [<c001bb88>] (warn_slowpath_fmt+0x44/0x6c)
[<c001bb88>] (warn_slowpath_fmt) from [<c0b0c4a8>]
(page_alloc_shuffle+0x12c/0x1ac)
[<c0b0c4a8>] (page_alloc_shuffle) from [<c0b0c550>] (shuffle_store+0x28/0x48)
[<c0b0c550>] (shuffle_store) from [<c003e6a0>] (parse_args+0x1f4/0x350)
[<c003e6a0>] (parse_args) from [<c0ac3c00>] (start_kernel+0x1c0/0x488)
Move the fallback call to jump_label_init() to occur before
parse_args().
The redundant calls to jump_label_init() in other archs are left intact
in case they have static key toggling use cases that are even earlier
than option parsing.
Link: http://lkml.kernel.org/r/155544804466.1032396.13418949511615676665.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Guenter Roeck <groeck@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Separate print_modules() and hard lockup error message.
Before the patch:
NMI watchdog: Watchdog detected hard LOCKUP on cpu 1Modules linked in: nls_cp437
Link: http://lkml.kernel.org/r/20190412062557.2700-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The help text for CONFIG_ARCH_HAS_KCOV is stale, and describes the
feature as being enabled only for x86_64, when it is now enabled for
several architectures, including arm, arm64, powerpc, and s390.
Let's remove that stale help text, and update it along the lines of hat
for ARCH_HAS_FORTIFY_SOURCE, better describing when an architecture
should select CONFIG_ARCH_HAS_KCOV.
Link: http://lkml.kernel.org/r/20190412102733.5154-1-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During !CONFIG_CGROUP reclaim, we expand the inactive list size if it's
thrashing on the node that is about to be reclaimed. But when cgroups
are enabled, we suddenly ignore the node scope and use the cgroup scope
only. The result is that pressure bleeds between NUMA nodes depending
on whether cgroups are merely compiled into Linux. This behavioral
difference is unexpected and undesirable.
When the refault adaptivity of the inactive list was first introduced,
there were no statistics at the lruvec level - the intersection of node
and memcg - so it was better than nothing.
But now that we have that infrastructure, use lruvec_page_state() to
make the list balancing decision always NUMA aware.
[hannes@cmpxchg.org: fix bisection hole]
Link: http://lkml.kernel.org/r/20190417155241.GB23013@cmpxchg.org
Link: http://lkml.kernel.org/r/20190412144438.2645-1-hannes@cmpxchg.org
Fixes: 2a2e48854d ("mm: vmscan: fix IO/refault regression in cache workingset transition")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
has_unmovable_pages() is used by allocating CMA and gigantic pages as
well as the memory hotplug. The later doesn't know how to offline CMA
pool properly now, but if an unused (free) CMA page is encountered, then
has_unmovable_pages() happily considers it as a free memory and
propagates this up the call chain. Memory offlining code then frees the
page without a proper CMA tear down which leads to an accounting issues.
Moreover if the same memory range is onlined again then the memory never
gets back to the CMA pool.
State after memory offline:
# grep cma /proc/vmstat
nr_free_cma 205824
# cat /sys/kernel/debug/cma/cma-kvm_cma/count
209920
Also, kmemleak still think those memory address are reserved below but
have already been used by the buddy allocator after onlining. This
patch fixes the situation by treating CMA pageblocks as unmovable except
when has_unmovable_pages() is called as part of CMA allocation.
Offlined Pages 4096
kmemleak: Cannot insert 0xc000201f7d040008 into the object search tree (overlaps existing)
Call Trace:
dump_stack+0xb0/0xf4 (unreliable)
create_object+0x344/0x380
__kmalloc_node+0x3ec/0x860
kvmalloc_node+0x58/0x110
seq_read+0x41c/0x620
__vfs_read+0x3c/0x70
vfs_read+0xbc/0x1a0
ksys_read+0x7c/0x140
system_call+0x5c/0x70
kmemleak: Kernel memory leak detector disabled
kmemleak: Object 0xc000201cc8000000 (size 13757317120):
kmemleak: comm "swapper/0", pid 0, jiffies 4294937297
kmemleak: min_count = -1
kmemleak: count = 0
kmemleak: flags = 0x5
kmemleak: checksum = 0
kmemleak: backtrace:
cma_declare_contiguous+0x2a4/0x3b0
kvm_cma_reserve+0x11c/0x134
setup_arch+0x300/0x3f8
start_kernel+0x9c/0x6e8
start_here_common+0x1c/0x4b0
kmemleak: Automatic memory scanning thread ended
[cai@lca.pw: use is_migrate_cma_page() and update commit log]
Link: http://lkml.kernel.org/r/20190416170510.20048-1-cai@lca.pw
Link: http://lkml.kernel.org/r/20190413002623.8967-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anson Huang
Jorge Ramirez-Ortiz
Fabrice Gasnier
Chen-Yu Tsai
Lucas Stach
Gustavo A. R. Silva
Jean-Francois Dagenais
Greg Kroah-Hartman
Alexander Usyskin
Tomas Winkler
Patrick Venture
Linus Torvalds
Ming Lei
Hou Tao
Hans de Goede
Ingo Molnar
Andrea Arcangeli
Arnd Bergmann
Dan Williams
Sergey Senozhatsky
Mark Rutland
Johannes Weiner
Qian Cai