Rather than always releasing the prisoners in a cell, the client may
want to promote one of them to be the new holder. There is a race here
though between releasing an empty cell, and other threads adding new
inmates. So this function makes the decision with its lock held.
This function can have two outcomes:
i) An inmate is promoted to be the holder of the cell (return value of 0).
ii) The cell has no inmate for promotion and is released (return value of 1).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We only allow non critical writeback if the origin is idle. It is up
to the policy to decide what writeback work is critical.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A little class that keeps track of the volume of io that is in flight,
and the length of time that a device has been idle for.
FIXME: rather than jiffes, may be best to use ktime_t (to support faster
devices).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There is a race between a policy deciding to replace a cache entry,
the core target writing back any dirty data from this block, and other
IO threads doing IO to the same block.
This sort of problem is avoided most of the time by the core target
grabbing a bio prison cell before making the request to the policy.
But for a demotion the core target doesn't know which block will be
demoted, so can't do this in advance.
Fix this demotion race by introducing a callback to the policy interface
that allows the policy to grab the cell on behalf of the core target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
A crypto driver can process requests synchronously or asynchronously
and can use an internal driver queue to backlog requests.
Add some comments to clarify internal logic and completion return codes.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Currently if there is a leg failure, the bio will be put into the hold
list until userspace does a remove/replace on the leg. Doing so in a
cluster config (clvmd) is problematic because there may be a temporary
path failure that results in cluster raid1 remove/replace. Such
recovery takes a long time due to a full resync.
Update dm-raid1 to optionally ignore these failures so bios continue
being issued without interrupton. To enable this feature userspace
must pass "keep_log" when creating the dm-raid1 device.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Tested-by: Liuhua Wang <lwang@suse.com>
Acked-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On 32-bit:
drivers/md/dm-log-writes.c: In function ‘log_super’:
drivers/md/dm-log-writes.c:323: warning: integer constant is too large for ‘long’ type
Add a ULL suffix to WRITE_LOG_MAGIC to fix this.
Also add a ULL suffix to WRITE_LOG_VERSION as it's stored in a __le64
field.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add dm-raid access to the MD RAID0 personality to enable single zone
striping.
The following changes enable that access:
- add type definition to raid_types array
- make bitmap creation conditonal in super_validate(), because
bitmaps are not allowed in raid0
- set rdev->sectors to the data image size in super_validate()
to allow the raid0 personality to calculate the MD array
size properly
- use mdddev(un)lock() functions instead of direct mutex_(un)lock()
(wrapped in here because it's a trivial change)
- enhance raid_status() to always report full sync for raid0
so that userspace checks for 100% sync will succeed and allow
for resize (and takeover/reshape once added in future paches)
- enhance raid_resume() to not load bitmap in case of raid0
- add merge function to avoid data corruption (seen with readahead)
that resulted from bio payloads that grew too large. This problem
did not occur with the other raid levels because it either did not
apply without striping (raid1) or was avoided via stripe caching.
- raise version to 1.7.0 because of the raid0 API change
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- ensure maximum device limit in superblock
- rename DMPF_* (print flags) to CTR_FLAG_* (constructor flags)
and their respective struct raid_set member
- use strcasecmp() in raid10_format_to_md_layout() as in the constructor
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove comment above parse_raid_params() that claims
"devices_handle_discard_safely" is a table line argument when it is
actually is a module parameter.
Also, backfill dm-raid target version 1.6.0 documentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Leverage the block manager's read_only flag instead of duplicating it;
access with new dm_bm_is_read_only() method.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The overwrite has only ever about optimizing away the need to zero a
block if the entire block was being overwritten. As such it is only
relevant when zeroing is enabled.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Introduce a single common method for cleaning up a DM device's
mapped_device. No functional change, just eliminates duplication of
delicate mapped_device cleanup code.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
More often than not a request that is requeued _is_ mapped (meaning the
clone request is allocated and clone->q is initialized). Rename
dm_requeue_unmapped_original_request() to avoid potential confusion due
to function name containing "unmapped".
Also, remove dm_requeue_unmapped_request() since callers can easily call
the dm_requeue_original_request() directly.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Do not allocate the io_pool mempool for blk-mq request-based DM
(DM_TYPE_MQ_REQUEST_BASED) in dm_alloc_rq_mempools().
Also refine __bind_mempools() to have more precise awareness of which
mempools each type of DM device uses -- avoids mempool churn when
reloading DM tables (particularly for DM_TYPE_REQUEST_BASED).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn"). In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int. This code made
assumptions about the value of BIO_MAX_SECTORS.
A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors(). At
this point the cast from sector_t to int resulted in a zero value. The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.
This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.19+
dm-multipath accepts 0 path mapping.
# echo '0 2097152 multipath 0 0 0 0' | dmsetup create newdev
Such a mapping can be used to release underlying devices while still
holding requests in its queue until working paths come back.
However, once the multipath device is created over blk-mq devices,
it rejects reloading of 0 path mapping:
# echo '0 2097152 multipath 0 0 1 1 queue-length 0 1 1 /dev/sda 1' \
| dmsetup create mpath1
# echo '0 2097152 multipath 0 0 0 0' | dmsetup load mpath1
device-mapper: reload ioctl on mpath1 failed: Invalid argument
Command failed
With following kernel message:
device-mapper: ioctl: can't change device type after initial table load.
DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.
Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.
Fixes: 65803c2059 ("dm table: train hybrid target type detection to select blk-mq if appropriate")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When stacking request-based dm device on non blk-mq device and
device-mapper target could not map the request (error target is used,
multipath target with all paths down, etc), the WARN_ON_ONCE() in
free_rq_clone() will trigger when it shouldn't.
The warning was added by commit aa6df8d ("dm: fix free_rq_clone() NULL
pointer when requeueing unmapped request"). But free_rq_clone() with
clone->q == NULL is valid usage for the case where
dm_kill_unmapped_request() initiates request cleanup.
Fix this false warning by just removing the WARN_ON -- it only generated
false positives and was never useful in catching the intended case
(completing clone request not being mapped e.g. clone->q being NULL).
Fixes: aa6df8d ("dm: fix free_rq_clone() NULL pointer when requeueing unmapped request")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use BLK_MQ_RQ_QUEUE_BUSY to requeue a blk-mq request directly from the
DM blk-mq device's .queue_rq. This cleans up the previous convoluted
handling of request requeueing that would return BLK_MQ_RQ_QUEUE_OK
(even though it wasn't) and then run blk_mq_requeue_request() followed
by blk_mq_kick_requeue_list().
Also, document that DM blk-mq ontop of old request_fn devices cannot
fail in clone_rq() since the clone request is preallocated as part of
the pdu.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When stacking request-based DM on blk_mq device, request cloning and
remapping are done in a single call to target's clone_and_map_rq().
The clone is allocated and valid only if clone_and_map_rq() returns
DM_MAPIO_REMAPPED.
The "IS_ERR(clone)" check in map_request() does not cover all the
!DM_MAPIO_REMAPPED cases that are possible (E.g. if underlying devices
are not ready or unavailable, clone_and_map_rq() may return
DM_MAPIO_REQUEUE without ever having established an ERR_PTR). Fix this
by explicitly checking for a return that is not DM_MAPIO_REMAPPED in
map_request().
Without this fix, DM core may call setup_clone() for a NULL clone
and oops like this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
IP: [<ffffffff81227525>] blk_rq_prep_clone+0x7d/0x137
...
CPU: 2 PID: 5793 Comm: kdmwork-253:3 Not tainted 4.0.0-nm #1
...
Call Trace:
[<ffffffffa01d1c09>] map_tio_request+0xa9/0x258 [dm_mod]
[<ffffffff81071de9>] kthread_worker_fn+0xfd/0x150
[<ffffffff81071cec>] ? kthread_parkme+0x24/0x24
[<ffffffff81071cec>] ? kthread_parkme+0x24/0x24
[<ffffffff81071fdd>] kthread+0xe6/0xee
[<ffffffff81093a59>] ? put_lock_stats+0xe/0x20
[<ffffffff81071ef7>] ? __init_kthread_worker+0x5b/0x5b
[<ffffffff814c2d98>] ret_from_fork+0x58/0x90
[<ffffffff81071ef7>] ? __init_kthread_worker+0x5b/0x5b
Fixes: e5863d9ad ("dm: allocate requests in target when stacking on blk-mq devices")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.0+
Without kicking queue, requeued request may stay forever in
the queue if there are no other I/O activities to the device.
The original error had been in v2.6.39 with commit 7eaceaccab
("block: remove per-queue plugging"), which replaced conditional
plugging by periodic runqueue.
Commit 9d1deb83d4 in v4.1-rc1 removed the periodic runqueue
and the problem started to manifest.
Fixes: 9d1deb83d4 ("dm: don't schedule delayed run of the queue if nothing to do")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This is a set of five fixes: Two MAINTAINER email updates (urgent because the
non-avagotech emails will start bouncing) an lpfc big endian oops fix, a 256
byte sector hang fix (to eliminate 256 byte sectors) and a storvsc fix which
could cause test unit ready failures on bringup.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVYPemAAoJEDeqqVYsXL0MK8UIAJJ8ViLPTfhweb8QgHsUjc4S
5x2jPUD69XT93G81NWKvFhYBnlAvktBZuy6uON7SkLWkbwgiu3pB1Iowqie+Z/h8
1C5VwC8oaT6GZPuakRRxnYmoAaCX7kbdMsibSvc5ouTgvM5FdailhJpkDKcFQlkn
t1GqmRQyH1P54O73af2d+z3AfNfivjoFFXz1YHcUOouiKBVyXzqk1c3CIwTQMelg
B547Rz2cqgdDtgQzZzPkfust/GOYs0ZQMU3rhjeNyIvw/5xa0/Ta2m/v16lckV2I
AvjK2Ht5XSr/Hc9m4yvr5vYCT5+mVrebYMghnUqpHjx1OGTBSU9lPT0exbCCJ/o=
=lXOs
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five fixes: Two MAINTAINER email updates (urgent
because the non-avagotech emails will start bouncing) an lpfc big
endian oops fix, a 256 byte sector hang fix (to eliminate 256 byte
sectors) and a storvsc fix which could cause test unit ready failures
on bringup"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: Revise lpfc maintainers for Avago Technologies ownership of Emulex
MAINTAINERS, be2iscsi: change email domain
sd: Disable support for 256 byte/sector disks
lpfc: Fix breakage on big endian kernels
storvsc: Set the SRB flags correctly when no data transfer is needed
Pull timer fix from Thomas Gleixner:
"One more fix from the timer departement:
- Handle division of negative nanosecond values proper on 32bit.
A recent cleanup wrecked the sign handling of the dividend and
dropped the check for negative divisors"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Fix ktime_divns to do signed division
Pull irqchip fix from Thomas Gleixner:
"A fix for a GIC-V3 irqchip regression which prevents some systems from
booting"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: ITS table size should not be smaller than PSZ
Pull two Ceph fixes from Sage Weil:
"These fix an issue with the RBD notifications when there are topology
changes in the cluster"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
Revert "libceph: clear r_req_lru_item in __unregister_linger_request()"
libceph: request a new osdmap if lingering request maps to no osd
Pull btrfs fixes from Chris Mason:
"I fixed up a regression from 4.0 where conversion between different
raid levels would sometimes bail out without converting.
Filipe tracked down a race where it was possible to double allocate
chunks on the drive.
Mark has a fix for fiemap. All three will get bundled off for stable
as well"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix regression in raid level conversion
Btrfs: fix racy system chunk allocation when setting block group ro
btrfs: clear 'ret' in btrfs_check_shared() loop
Pull drm fixes from Dave Airlie:
"Radeon has two displayport fixes, one for a regression.
i915 regression flicker fix needed so 4.0 can get fixed.
A bunch of msm fixes and a bunch of exynos fixes, these two are
probably a bit larger than I'd like, but most of them seems pretty
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
drm/i915: fix screen flickering
drm/msm: fix locking inconsistencies in gpu->destroy()
drm/msm/dsi: Simplify the code to get the number of read byte
drm/msm: Attach assigned encoder to eDP and DSI connectors
...
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
- one serious RAID0 data corruption - caused by recent bugfix that wasn't
reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jXKM
-----END PGP SIGNATURE-----
Merge tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"I have a few more raid5 bugfixes pending, but I want them to get a bit
more review first. In the meantime:
- one serious RAID0 data corruption - caused by recent bugfix that
wasn't reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation"
* tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md:
md/bitmap: remove rcu annotation from pointer arithmetic.
md/raid0: fix restore to sector variable in raid0_make_request
raid5: fix broken async operation chain
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
Pull another crypto fix from Herbert Xu:
"Fix ICV corruption in s390/ghash when the same tfm is used by more
than one thread"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s390/ghash - Fix incorrect ghash icv buffer handling.
When trying to configure the settings for PHY1, using commands
like 'ethtool -s eth0 phyad 1 speed 100', the 'ethtool' seems to
modify other settings apart from the speed of the PHY1, in the
above case.
The ethtool seems to query the settings for PHY0, and use this
as the base to apply the new settings to the PHY1. This is
causing the other settings of the PHY 1 to be wrongly
configured.
The issue is caused by the '_ethtool_get_settings()' API, which
gets called because of the 'ETHTOOL_GSET' command, is clearing
the 'cmd' pointer (of type 'struct ethtool_cmd') by calling
memset. This clears all the parameters (if any) passed for the
'ETHTOOL_GSET' cmd. So the driver's callback is always invoked
with 'cmd->phy_address' as '0'.
The '_ethtool_get_settings()' is called from other files in the
'net/core'. So the fix is applied to the 'ethtool_get_settings()'
which is only called in the context of the 'ethtool'.
Signed-off-by: Arun Parameswaran <aparames@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When more than a multicast address is present in a MLDv2 report, all but
the first address is ignored, because the code breaks out of the loop if
there has not been an error adding that address.
This has caused failures when two guests connected through the bridge
tried to communicate using IPv6. Neighbor discoveries would not be
transmitted to the other guest when both used a link-local address and a
static address.
This only happens when there is a MLDv2 querier in the network.
The fix will only break out of the loop when there is a failure adding a
multicast address.
The mdb before the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
After the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::fb temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
dev ovirtmgmt port bond0.86 grp ff02::d temp
dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp
dev ovirtmgmt port bond0.86 grp ff02::16 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp
dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp
dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp
Fixes: 08b202b672 ("bridge br_multicast: IPv6 MLD support.")
Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing an IPv4 route, tb_id member of the new fib_alias
structure is not set in the replace code path so that the new route is
ignored.
Fixes: 0ddcf43d5d ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e21 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contain Netfilter fixes for your net tree, they are:
1) Fix a race in nfnetlink_log and nfnetlink_queue that can lead to a crash.
This problem is due to wrong order in the per-net registration and netlink
socket events. Patch from Francesco Ruggeri.
2) Make sure that counters that userspace pass us are higher than 0 in all the
x_tables frontends. Discovered via Trinity, patch from Dave Jones.
3) Revert a patch for br_netfilter to rely on the conntrack status bits. This
breaks stateless IPv6 NAT transformations. Patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da41301 ("ipv4: Cache ip_error() routes even when not forwarding.")
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Thornber
Milan Broz
Lidong Zhong
Geert Uytterhoeven
Luis Henriques
Heinz Mauelshagen
Mike Snitzer
Junichi Nomura
Julia Lawall
Linus Torvalds
Eric Dumazet
Arun Parameswaran
Thadeu Lima de Souza Cascardo
Nathan Sullivan
Michal Kubeček
Bjørn Mork
David S. Miller
Eric W. Biederman