A documentation update exposed the existance of the turbo ratio
register. Update baytrail support to use the turbo range.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
LFM (max efficiency ratio) is the max frequency at minimum voltage
supported by the processor. Using LFM as the minimum P state
increases performmance without affecting power. By not using P states
below LFM we avoid using P states that are less power efficient.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change "dummy supplies not allowed" error message to warning instead, as this
is a just warning message with no change to the behavior.
[Added a CC to stable since some other bug fixes cause this to come up
more frequently on PCs which is how it was noticed -- broonie]
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Here are 10 fixes for our current -rc cycle. It's likely
the last round of fixes for this merge window. All patches
have soaked for a long time and have all been tested in real
HW.
The most interesting fixes are a fix for enumeration of superspeed
hubs when MUSB is acting as host, and a remote-wakeup fix also on
MUSB.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AnZJ
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.14-rc4
Here are 10 fixes for our current -rc cycle. It's likely
the last round of fixes for this merge window. All patches
have soaked for a long time and have all been tested in real
HW.
The most interesting fixes are a fix for enumeration of superspeed
hubs when MUSB is acting as host, and a remote-wakeup fix also on
MUSB.
Signed-of-by: Felipe Balbi <balbi@ti.com>
MSI
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CTv7
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The most interesting thing here is the change to enable INTx (by
clearing PCI_COMMAND_INTX_DISABLE) if the BIOS left INTx disabled.
Apparently the Baytrail BIOS does this, which means EHCI doesn't work.
Also, fix an AHCI MSI regression and other issues with the recent MSI
changes. This also adds pci_enable_msi_exact() and
pci_enable_msix_exact(), which aren't regression fixes, but will keep
us from touching drivers twice (once to stop using the deprecated
pci_enable_msi(), etc., and again to use the *_exact() variants).
There's also a minor MVEBU fix.
Summary:
MSI:
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous:
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)"
* tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ahci: Fix broken fallback to single MSI mode
PCI: Enable INTx if BIOS left them disabled
PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact()
PCI/MSI: Fix cut-and-paste errors in documentation
PCI/MSI: Add pci_enable_msi() documentation back
PCI/MSI: Fix pci_msix_vec_count() htmldocs failure
PCI/MSI: Fix leak of msi_attrs
PCI/MSI: Check kmalloc() return value, fix leak of name
PCI: mvebu: Use Device ID and revision from underlying endpoint
Fix regression caused by commit b072e53, which breaks loading nouveau
driver on optimus laptops.
On some platforms, ACPI _DSM method (nouveau_op_dsm_muid, function 0)
has special requirements on the fourth parameter, which is different
from ACPI specifications. So revert to the private implementation
to check availability of _DSM functions instead of using common
acpi_check_dsm() interface.
Fixes: b072e53b0a (ACPI / nouveau: replace open-coded _DSM code with helper functions)
Reported-and-tested-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
[rjw: Subject]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull libata fixes from Tejun Heo:
"Various device specific fixes. Nothing too interesting"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable NCQ on Samsung pci-e SSDs on macbooks
ata: sata_mv: Cleanup only the initialized ports
sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYN
ata: enable quirk from jmicron JMB350 for JMB394
ATA: SATA_MV: Add missing Kconfig select statememnt
ata: pata_imx: Check the return value from clk_prepare_enable()
sparc_cpu_model isn't in asm/system.h any more, so remove a comment
about it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
schedule_delayed_work() takes the delay in jiffies, not msecs.
This bug slipped in with the recent reset logic cleanup
(8ed1fb790ea: "usb: musb: finish suspend/reset work independently from
musb_hub_control()").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both the PM_RUNTIME and PM_SLEEP callbacks call into the common
msm_otg_{suspend,resume} routines, however these routines are only being
built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also
depends on msm_hsusb_config_vddcx(), which is only built when
CONFIG_PM_SLEEP.
Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the
preprocessor conditional, and moving msm_hsusb_config_vddcx().
While we're here, eliminate the CONFIG_PM conditional for setting
up the dev_pm_ops.
This address the following errors Russell King has hit doing randconfig
builds:
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend'
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix possible NULL pointer dereference introduced in
commit 219580e (usb: f_fs: check quirk to pad epout
buf size when not aligned to maxpacketsize)
In cases we do wait with:
wait_event_interruptible(epfile->wait, (ep = epfile->ep));
for endpoint to be enabled, functionfs_bind() has not been called yet
and epfile->ffs->gadget is still NULL and the automatic variable 'gadget'
has been initialized with NULL at the point of its definition.
Later on it is used as a parameter to:
usb_ep_align_maybe(gadget, ep->ep, len)
which in turn dereferences it.
This patch fixes it by moving the actual assignment to the local 'gadget'
variable after the potential waiting has completed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to use gadget_is_otg to check if the gadget is really
otg support at runtime, other composite gadget drivers have already
followed this method.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As the lock might be used through DMA-API which is allowed
in interrupt context.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Adds a selftest function for the of_match_node function. of_match_node
is supposed to handle precedence for the compatible property as well as
the name and device_type values. This patch adds some test case data and
a function that makes sure each test node matches against the correct
entry of an of_device_id table.
This code was written to verify the new of_match_node() implementation
that is an earlier part of this series.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Kevin Hao <haokexin@gmail.com>
The testcase data is usable by any platform. This patch moves it into
the drivers/of directory so it can be included by any architecture.
Using the test cases requires manually adding #include <testcases.dtsi>
to the end of the boards .dtsi file and enabling CONFIG_OF_SELFTEST. Not
pretty though. A useful project would be to make the testcase code
easier to execute.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
In the current implementation of __of_match_node(), it will compare
each given match entry against all the node's compatible strings
with of_device_is_compatible().
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and
also an alphabetical ordering is more sane there.
Therefore, we define a following priority order for the match, and
then scan all the entries to find the best match.
1. specific compatible && type && name
2. specific compatible && type
3. specific compatible && name
4. specific compatible
5. general compatible && type && name
6. general compatible && type
7. general compatible && name
8. general compatible
9. type && name
10. type
11. name
v5: Fix nested locking bug
v4: Short-circuit failure cases instead of mucking with score, and
remove extra __of_device_is_compatible() wrapper stub.
Move scoring logic directly into __of_device_is_compatible()
v3: Also need to bail out when there does have a compatible member in match
entry, but it doesn't match with the device node's compatible.
v2: Fix the bug such as we get the same score for the following two match
entries with the empty node 'name2 { };'
struct of_device_id matches[] = {
{.name = "name2", },
{.name = "name2", .type = "type1", },
{}
};
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[grant.likely: added v4 changes]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
This reverts commit 2d4054d842 (ACPI: Blacklist Win8 OSI for some HP
laptop 2013 models) that is not necessary any more after previous
commit 1811fcb029fa (ACPI / video: Add systems that should favour native
backlight interface).
Requested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some system's ACPI video backlight control interface is broken and the
native backlight control interface should be used by default. This patch
sets the use_native_backlight parameter to true for those systems so
that video backlight control interface will not be created. For detailed
models that are added here, reference the following list.
Note that the user specified kernel cmdline option will always have the
highest priority, i.e. if use_native_backlight=0 is specified and the
system is in the DMI table, the video module will not skip registering
backlight interface for it.
Thinkpad T430s:
Reported-by: Theodore Tso <tytso@mit.edu>
Reported-and-tested-by: Peter Weber <bugs@ttyhoney.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=51231
Thinkpad X230:
Reported-and-tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=51231
ThinkPad X1 Carbon:
Reported-and-tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Lenovo Yoga 13:
Reported-by: Lennart Poettering <lennart@poettering.net>
Reported-and-tested-by: Kevin Smith <thirdwiggin@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=63811
Dell Inspiron 7520:
Reported-by: Rinat Ibragimov <ibragimovrinat@mail.ru>
Acer Aspire 5733Z:
Reported-by: <sov.info@mail.ru>
References: https://bugzilla.kernel.org/show_bug.cgi?id=62941
Acer Aspire V5-431:
Reported-by: Thomas Christensen <christensenthomas@gmail.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=68751
HP ProBook 4340s:
Reported-and-tested-by: Vladimir Sherenkov <a_12300@mail.ru>
References: http://redmine.russianfedora.pro/issues/1258
HP EliteBook/ProBook 2013 models, ZBook and some others:
Provided-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices have duplicate entries in there brightness levels table, ie
on my Dell Latitude E6430 the table looks like this:
[ 3.686060] acpi backlight index 0, val 80
[ 3.686095] acpi backlight index 1, val 50
[ 3.686122] acpi backlight index 2, val 5
[ 3.686147] acpi backlight index 3, val 5
[ 3.686172] acpi backlight index 4, val 5
[ 3.686197] acpi backlight index 5, val 5
[ 3.686223] acpi backlight index 6, val 5
[ 3.686248] acpi backlight index 7, val 5
[ 3.686273] acpi backlight index 8, val 6
[ 3.686332] acpi backlight index 9, val 7
[ 3.686356] acpi backlight index 10, val 8
[ 3.686380] acpi backlight index 11, val 9
etc.
Notice that brightness values 0-5 are all mapped to 5. This means that
if userspace writes any value between 0 and 5 to the brightness sysfs attribute
and then reads it, it will always return 0, which is somewhat unexpected.
This is a problem for ie gnome-settings-daemon, which uses read-modify-write
logic when the users presses the brightness up or down keys. This is done
this way to take brightness changes from other sources into account.
On this specific laptop what happens once the brightness has been set to 0,
is that gsd reads 0, adds 5, writes 5, and on the next brightness up key press
again reads 0, so things get stuck at the lowest brightness setting.
Filtering out the duplicate table entries, makes any write to brightness
read back as the written value as one would expect, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Couple of small issues solved:
- Suspend/Resume call-backs require CONFIG_PM_SLEEP
- Some drivers written for 32bit architectures fail when compiled
with a 64bit compiler. The fixes will future proof the drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=705r
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.14-1' of git://git.linaro.org/people/lee.jones/mfd
Pull MFD fixes from Lee Jones:
"Couple of small issues solved:
- Suspend/Resume call-backs require CONFIG_PM_SLEEP
- Some drivers written for 32bit architectures fail when compiled
with a 64bit compiler. The fixes will future proof the drivers"
* tag 'mfd-fixes-3.14-1' of git://git.linaro.org/people/lee.jones/mfd:
mfd: sec-core: sec_pmic_{suspend,resume}() should depend on CONFIG_PM_SLEEP
mfd: max14577: max14577_{suspend,resume}() should depend on CONFIG_PM_SLEEP
mfd: tps65217: Naturalise cross-architecture discrepancies
mfd: wm8994-core: Naturalise cross-architecture discrepancies
mfd: max8998: Naturalise cross-architecture discrepancies
mfd: max8997: Naturalise cross-architecture discrepancies
If CONFIG_PM_SLEEP=n:
drivers/mfd/sec-core.c:349: warning: ‘sec_pmic_suspend’ defined but not used
drivers/mfd/sec-core.c:371: warning: ‘sec_pmic_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If CONFIG_PM_SLEEP=n:
drivers/mfd/max14577.c:177: warning: ‘max14577_suspend’ defined but not used
drivers/mfd/max14577.c:200: warning: ‘max14577_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the TPS65217 for a 64bit architecture we receive the following
warnings:
drivers/mfd/tps65217.c: In function ‘tps65217_probe’:
drivers/mfd/tps65217.c:173:13:
warning: cast from pointer to integer of different size
chip_id = (unsigned int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the WM8994 for a 64bit architecture we receive the following
warnings:
drivers/mfd/wm8994-core.c: In function ‘wm8994_i2c_probe’:
drivers/mfd/wm8994-core.c:639:19:
warning: cast from pointer to integer of different size
wm8994->type = (int)of_id->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the MAX8998 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8998.c: In function ‘max8998_i2c_get_driver_data’:
drivers/mfd/max8998.c:178:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the MAX8997 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8997.c: In function ‘max8997_i2c_get_driver_data’:
drivers/mfd/max8997.c:173:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull drm fixes from Dave Airlie:
"Lots of little small things, nothing too major: nouveau regression
fixes, vmware fixes for the new hw support, memory leaks in error path
fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
drm/radeon/ni: fix typo in dpm sq ramping setup
drm/radeon/si: fix typo in dpm sq ramping setup
drm/radeon: fix CP semaphores on CIK
drm/radeon: delete a stray tab
drm/radeon: fix display tiling setup on SI
drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
drm/radeon: fill in DRM_CAPs for cursor size
drm: add DRM_CAPs for cursor size
drm/radeon: unify bpc handling
drm/ttm: Fix memory leak in ttm_agp_backend.c
drm/ttm: declare 'struct device' in ttm_page_alloc.h
drm/nouveau: fix TTM_PL_TT memtype on pre-nv50
drm/nv50/disp: use correct register to determine DP display bpp
drm/nouveau/fb: use correct ram oclass for nv1a hardware
drm/nv50/gr: add missing nv_error parameter priv
drm/nouveau: fix ENG_RUNLIST register address
drm/nv4c/bios: disallow retrieving from prom on nv4x igp's
drm/nv4c/vga: decode register is in a different place on nv4x igp's
drm/nv4c/mc: nv4x igp's have a different msi rearm register
drm/nouveau: set irq_enabled manually
...
Pull HID update from Jiri Kosina:
- fixes for several bugs in incorrect allocations of buffers by David
Herrmann and Benjamin Tissoires.
- support for a few new device IDs by Archana Patni, Benjamin
Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hyperv: make sure input buffer is big enough
HID: Bluetooth: hidp: make sure input buffers are big enough
HID: hid-sensor-hub: quirk for STM Sensor hub
HID: apple: add Apple wireless keyboard 2011 JIS model support
HID: fix buffer allocations
HID: multitouch: add FocalTech FTxxxx support
HID: microsoft: Add ID's for Surface Type/Touch Cover 2
HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay
The powernow-k8 driver maintains a per-cpu data-structure called
powernow_data that is used to perform the frequency transitions.
It initializes this data structure only for the policy->cpu. So,
accesses to this data structure by other CPUs results in various
problems because they would have been uninitialized.
Specifically, if a cpu (!= policy->cpu) invokes the drivers' ->get()
function, it returns 0 as the KHz value, since its per-cpu memory
doesn't point to anything valid. This causes problems during
suspend/resume since cpufreq_update_policy() tries to enforce this
(0 KHz) as the current frequency of the CPU, and this madness gets
propagated to adjust_jiffies() as well. Eventually, lots of things
start breaking down, including the r8169 ethernet card, in one
particularly interesting case reported by Pierre Ossman.
Fix this by initializing the per-cpu data-structures of all the CPUs
in the policy appropriately.
References: https://bugzilla.kernel.org/show_bug.cgi?id=70311
Reported-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 42f921a (cpufreq: remove sysfs files for CPUs which failed to
come back after resume) tried to do this but missed this piece of code
to fix.
Currently we are getting this on suspend/resume:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 877 at fs/sysfs/dir.c:52 sysfs_warn_dup+0x68/0x84()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu1/cpufreq'
Modules linked in: brcmfmac brcmutil
CPU: 0 PID: 877 Comm: test-rtc-resume Not tainted 3.14.0-rc2-00259-g9398a10cd964 #12
[<c0015bac>] (unwind_backtrace) from [<c0011850>] (show_stack+0x10/0x14)
[<c0011850>] (show_stack) from [<c056e018>] (dump_stack+0x80/0xcc)
[<c056e018>] (dump_stack) from [<c0025e44>] (warn_slowpath_common+0x64/0x88)
[<c0025e44>] (warn_slowpath_common) from [<c0025efc>] (warn_slowpath_fmt+0x30/0x40)
[<c0025efc>] (warn_slowpath_fmt) from [<c012776c>] (sysfs_warn_dup+0x68/0x84)
[<c012776c>] (sysfs_warn_dup) from [<c0127a54>] (sysfs_do_create_link_sd+0xb0/0xb8)
[<c0127a54>] (sysfs_do_create_link_sd) from [<c038ef64>] (__cpufreq_add_dev.isra.27+0x2a8/0x814)
[<c038ef64>] (__cpufreq_add_dev.isra.27) from [<c038f548>] (cpufreq_cpu_callback+0x70/0x8c)
[<c038f548>] (cpufreq_cpu_callback) from [<c0043864>] (notifier_call_chain+0x44/0x84)
[<c0043864>] (notifier_call_chain) from [<c0025f60>] (__cpu_notify+0x28/0x44)
[<c0025f60>] (__cpu_notify) from [<c00261e8>] (_cpu_up+0xf0/0x140)
[<c00261e8>] (_cpu_up) from [<c0569eb8>] (enable_nonboot_cpus+0x68/0xb0)
[<c0569eb8>] (enable_nonboot_cpus) from [<c006339c>] (suspend_devices_and_enter+0x198/0x2dc)
[<c006339c>] (suspend_devices_and_enter) from [<c0063654>] (pm_suspend+0x174/0x1e8)
[<c0063654>] (pm_suspend) from [<c00624e0>] (state_store+0x6c/0xbc)
[<c00624e0>] (state_store) from [<c01fc200>] (kobj_attr_store+0x14/0x20)
[<c01fc200>] (kobj_attr_store) from [<c0126e50>] (sysfs_kf_write+0x44/0x48)
[<c0126e50>] (sysfs_kf_write) from [<c012a274>] (kernfs_fop_write+0xb4/0x14c)
[<c012a274>] (kernfs_fop_write) from [<c00d4818>] (vfs_write+0xa8/0x180)
[<c00d4818>] (vfs_write) from [<c00d4bb8>] (SyS_write+0x3c/0x70)
[<c00d4bb8>] (SyS_write) from [<c000e620>] (ret_fast_syscall+0x0/0x30)
---[ end trace 76969904b614c18f ]---
Fix this by removing sysfs link for cpufreq directory when cpu removed
isn't policy->cpu.
Revamps: 42f921a (cpufreq: remove sysfs files for CPUs which failed to come back after resume)
Reported-and-tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When trying to set the minimum temperature, the driver was erroneously
writing the maximum temperature into the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # v3.2+
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Pull networking fixes from David Miller:
1) kvaser CAN driver has fixed limits of some of it's table, validate
that we won't exceed those limits at probe time. Fix from Olivier
Sobrie.
2) Fix rtl8192ce disabling interrupts for too long, from Olivier
Langlois.
3) Fix botched shift in ath5k driver, from Dan Carpenter.
4) Fix corruption of deferred packets in TIPC, from Erik Hugne.
5) Fix newlink error path in macvlan driver, from Cong Wang.
6) Fix netpoll deadlock in bonding, from Ding Tianhong.
7) Handle GSO packets properly in forwarding path when fragmentation is
necessary on egress, from Florian Westphal.
8) Fix axienet build errors, from Michal Simek.
9) Fix refcounting of ubufs on tx in vhost net driver, from Michael S
Tsirkin.
10) Carrier status isn't set properly in hyperv driver, from Haiyang
Zhang.
11) Missing pci_disable_device() in tulip_remove_one), from Ingo Molnar.
12) AF_PACKET qdisc bypass mode doesn't adhere to driver provided TX
queue selection method. Add a fallback method mechanism to fix this
bug, from Daniel Borkmann.
13) Fix regression in link local route handling on GRE tunnels, from
Nicolas Dichtel.
14) Bonding can assign dup aggregator IDs in some sequences of
configuration, fix by making the allocation counter per-bond instead
of global. From Jiri Bohac.
15) sctp_connectx() needs compat translations, from Daniel Borkmann.
16) Fix of_mdio PHY interrupt parsing, from Ben Dooks
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
MAINTAINERS: add entry for the PHY library
of_mdio: fix phy interrupt passing
net: ethernet: update dependency and help text of mvneta
NET: fec: only enable napi if we are successful
af_packet: remove a stray tab in packet_set_ring()
net: sctp: fix sctp_connectx abi for ia32 emulation/compat mode
ipv4: fix counter in_slow_tot
irtty-sir.c: Do not set_termios() on irtty_close()
bonding: 802.3ad: make aggregator_identifier bond-private
usbnet: remove generic hard_header_len check
gre: add link local route when local addr is any
batman-adv: fix potential kernel paging error for unicast transmissions
batman-adv: avoid double free when orig_node initialization fails
batman-adv: free skb on TVLV parsing success
batman-adv: fix TT CRC computation by ensuring byte order
batman-adv: fix potential orig_node reference leak
batman-adv: avoid potential race condition when adding a new neighbour
batman-adv: properly check pskb_may_pull return value
batman-adv: release vlan object after checking the CRC
batman-adv: fix TT-TVLV parsing on OGM reception
...
Pull ARM fixes from Russell King:
"A range of ARM fixes. Biggest change is the stage-2 attributes used
for for hyp mode which were wrong. I've killed some bits in a couple
of DT files which turned out not to be required, and a few other
fixes.
One fix touches code outside of arch/arm, which is related to sorting
out the DMA masks correctly. There is a long standing issue with the
conversion from PFNs to addresses where people assume that shifting an
unsigned long left by PAGE_SHIFT results in a correct address. This
is not the case with C: the integer promotion happens at assignment
after evaluation. This fixes the recently introduced dma_max_pfn()
function, but there's a number of other places where we try this
directly on an unsigned long in the mm code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
Fix uses of dma_max_pfn() when converting to a limiting address
ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
ARM: 7950/1: mm: Fix stage-2 device memory attributes
ARM: dts: fix spdif pinmux configuration
The of_mdiobus_register_phy() is not setting phy->irq thus causing
some drivers to incorrectly assume that the PHY does not have an
IRQ associated with it. Not only do some drivers report no IRQ
they do not install an interrupt handler for the PHY.
Simplify the code setting irq and set the phy->irq at the same
time so that we cover the following issues, which should cover
all the cases the code will find:
- Set phy->irq if node has irq property and mdio->irq is NULL
- Set phy->irq if node has no irq and mdio->irq is not NULL
- Leave phy->irq as PHY_POLL default if none of the above
This fixes the issue:
net eth0: attached PHY 1 (IRQ -1) to driver Micrel KSZ8041RNLI
to the correct:
net eth0: attached PHY 1 (IRQ 416) to driver Micrel KSZ8041RNLI
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of the support for Armada 375 and Armada 38x,
the hidden Kconfig option MACH_ARMADA_370_XP is being renamed to
MACH_MVEBU_V7. Therefore, the dependency that was used for the mvneta
driver can no longer work. This commit replaces this dependency by a
dependency on PLAT_ORION, which is used similarly for the mv643xx_eth
driver.
In addition to this, it takes this opportunity to adjust the
description and help text to indicate that the driver can is also used
for Armada 38x. Note that Armada 375 cannot use this driver as it has
a completely different networking unit, which will require a separate
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If napi is left enabled after a failed attempt to bring the interface
up, we BUG:
fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc
Only enable napi after we are past all the failure paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 06b29e76a7.
As pointed out by Grant Likely, we should also take the type and name
into account when searching the best compatible match. That means the
match with compatible, type and name should be better than the match
just with the same compatible string. So revert this and we will
implement another method to find the best match entry.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Pull request of 2014-02-18
One compile fix and one memory leak.
* tag 'ttm-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
drm/ttm: Fix memory leak in ttm_agp_backend.c
drm/ttm: declare 'struct device' in ttm_page_alloc.h
Pull request of 2014-02-18.
Nothing special. The biggest change is adding a couple of command defines and
packing the command data correctly.
* tag 'vmwgfx-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix command defines and checks
drm/vmwgfx: Fix possible integer overflow
drm/vmwgfx: Remove stray const
drm/vmwgfx: unlock on error path in vmw_execbuf_process()
drm/vmwgfx: Get maximum mob size from register SVGA_REG_MOB_MAX_SIZE
drm/vmwgfx: Fix a couple of sparse warnings and errors
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.14 stream...
For the iwlwifi one, Emmanuel says:
"As explicitly written in the commit message, we prefer to disable Tx
AMPDU on NICs supported by iwldvm. This feature gives a big boost in
Tx performance, but the firmware is buggy and we can't rely on it.
Our hope is that most of the users out there want wifi to surf on
the web which means that they care more for Rx traffic than for Tx.
People who want to enable it can do so with the help of a module
parameter."
On top of that...
Dan Carpenter fixes a typo/thinko in ath5k.
Olivier Langlois fixes a couple of rtlwifi issues, one which leaves
IRQs disabled too long (causing a variety of problems elsewhere),
and one which fixes an incorrect return code when failing to enable
the NIC.
Russell King fixes a NULL pointer dereference in hostap.
Stanislaw Gruszka fixes a DMA coherence issue in the rtl8187 driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Registering phy_provider before creating the PHY can result in PHY
callbacks being invoked which will lead to aborts. In order to avoid this
invoke phy_provider_register after phy_create and phy_set_drvdata.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/phy/phy.h has stub code in there for when building without the
phy-core enabled. This is useful for generic drivers such as ahci-platform,
ehci-platoform and ohci-platform which have support for driving an optional
phy passed to them through the devicetree.
Since on some boards this phy functionality is not needed, being able to
disable the phy subsystem without needing a lot of #ifdef magic in the
driver using it is quite useful.
However this breaks when the module using the phy subsystem is build-in and
the phy-core is not, which leads to the build failing with missing symbol
errors in the linking stage of the zImage.
Which leads to gems such as this being added to the Kconfig for achi_platform:
depends on GENERIC_PHY || !GENERIC_PHY
Rather then duplicating this code in a lot of places using the phy-core,
I believe it is better to simply not allow the phy-core to be built as a
module. The phy core is quite small and has no external dependencies, so
always building it in when enabling it should not be an issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy-core allows phy_init and phy_power_on to be called multiple times,
but before this patch -ENOSUPP from phy_pm_runtime_get_sync would be
propagated to the caller for the 2nd and later calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In various cases errors may be expected, ie probe-deferral or a call to
phy_get from a driver where the use of a phy is optional.
Rather then adding all sort of complicated checks for this, and/or adding
special functions like devm_phy_get_optional, simply don't log an error,
and let deciding if get_phy returning an error really should result in a
dev_err up to the caller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/phy/phy-bcm-kona-usb2.c:114: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
schedule_delayed_work() takes the delay in jiffies, not msecs. Fix the
caller sites in musb. This bug caused regressions with the cleanups
that went in for 3.14 (8ed1fb790ea: "usb: musb: finish suspend/reset
work independently from musb_hub_control()").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
High-speed USB connections revert back to full-speed signalling when
the device goes into suspend. This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.
On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state. It generates a false wakeup signal,
which can prevent the controller from going to sleep.
To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling. (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <Peter.Chen@freescale.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CP semaphore queue on CIK has a bug that triggers if uncompleted
waits use the same address while a signal is still pending. Work around
this by using different addresses for each sync.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Static checkers complain that probably curly braces were intended here,
but actually it makes more sense to remove the extra tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most laptops seems to have a vblank period of less than
300 and mclk switching works fine. Drop the quirk and
set the default threshold to 200.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=70701
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some hardware may not support standard 64x64 cursors. Add
a drm cap to query the cursor size from the kernel. Some examples
include radeon CIK parts (128x128 cursors) and armada (32x64 or 64x32).
This allows things like device specific ddxes to remove asics specific
logic and also allows xf86-video-modesetting to work properly with hw
cursors on this hardware. Default to 64 if the driver doesn't specify
a size.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
We were already storing the bpc (bits per color) information
in radeon_crtc, so just use that everywhere rather than
calculating it everywhere we use it. This also allows us
to change it in one place if we ever want to override it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 3dc6475 ("bcm63xx_enet: add support Broadcom BCM6345 Ethernet")
changed the ENETDMA[CS] macros such that they are no longer macros, but
actual register offset definitions. The bcm63xx_udc driver was not
updated, and as a result, causes the following build error to pop up:
CC drivers/usb/gadget/u_ether.o
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_write':
drivers/usb/gadget/bcm63xx_udc.c:642:24: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_reset_channel':
drivers/usb/gadget/bcm63xx_udc.c:698:46: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c:700:49: error: called object '0' is not
a function
Fix this by updating usb_dmac_{read,write}l and usb_dmas_{read,write}l to
take an extra channel argument, and use the channel width
(ENETDMA_CHAN_WIDTH) to offset the register we want to access, hence
doing again what the macro implicitely did for us.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pass value instead of address as expected by 'usb_ep_set_maxpacket_limit'.
Fixes the following compilation error introduced by commit e117e742d3
("usb: gadget: add "maxpacket_limit" field to struct usb_ep"):
drivers/usb/gadget/s3c2410_udc.c: In function ‘s3c2410_udc_reinit’:
drivers/usb/gadget/s3c2410_udc.c:1632:3: error:
cannot take address of bit-field ‘maxpacket’
usb_ep_set_maxpacket_limit(&ep->ep, &ep->ep.maxpacket);
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During resume don't touch SUSPENDM/RESUME bits of POWER register
while restoring controller context. These bits might be changed
by the controller during resume operation and so will be different
than what they were during suspend.
e.g. SUSPENDM bit is set by software during USB global suspend but
automatically cleared by the controller during remote wakeup or
during resume. Setting this bit back while restoring context
causes undesired behaviour. i.e. Babble interrupt is generated
and USB is broken.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disables PING on status phase of control transfer.
PING token is not mandatory in status phase of control transfer
and so some high speed USB devices don't support it. If such devices
are connected to MUSB then they would not respond to PING token
causing delayed or failed enumeration.
[Roger Q] Fixes enumeration issues with some Super-Speed USB hubs
e.g. Dlink DUB-1340
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Cc: stable@vger.kernel.org
acpi_pci_link_allocate_irq() can return negative gsi even if
entry != NULL. For that case we have a memory leak, so free
entry before returning from acpi_pci_irq_enable() for gsi < 0.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fix a memory leak found by cppcheck.
[drivers/gpu/drm/ttm/ttm_agp_backend.c:129]:
(error) Memory leak: agp_be
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Nothing too exciting, mostly fixes for ancient boards, but a pretty important fix for DP on some systems.
Thanks,
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: fix TTM_PL_TT memtype on pre-nv50
drm/nv50/disp: use correct register to determine DP display bpp
drm/nouveau/fb: use correct ram oclass for nv1a hardware
drm/nv50/gr: add missing nv_error parameter priv
drm/nouveau: fix ENG_RUNLIST register address
drm/nv4c/bios: disallow retrieving from prom on nv4x igp's
drm/nv4c/vga: decode register is in a different place on nv4x igp's
drm/nv4c/mc: nv4x igp's have a different msi rearm register
drm/nouveau: set irq_enabled manually
3 fixes plus 1 prep patch, all four cc: stable. Jani will take over from
here and the plan is that he'll do 3.14-fixes for the entire release just
to work things out a bit.
* tag 'drm-intel-fixes-2014-02-14' of ssh://git.freedesktop.org/git/drm-intel:
drm/i915/dp: add native aux defer retry limit
drm/i915/dp: increase native aux defer retry timeout
drm/i915: Prevent MI_DISPLAY_FLIP straddling two cachelines on IVB
drm/i915: Add intel_ring_cachline_align()
fix for leak in tda998x
* 'tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
drm/i2c: tda998x: Fix memory leak in tda998x_encoder_init error path.
Commit a55409066 ("drm/nv50-: map TTM_PL_SYSTEM through a BAR for CPU
access") made it possible to work with tiled memory. However
mem->mm_node is not a nouveau_mem for AGP-using pre-NV50 cards, but a
drm_mm_node, as created by the ttm_bo_manager_func. As such, extend the
untiled check to explicitly include all pre-nv50 cards.
Reported-by: Ronald <ronald645@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74613
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Tested-by: Ronald Uitermark <ronald645@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit 0a0afd282f ("drm/nv50-/disp: move DP link training to core and
train from supervisor") added code that uses the wrong register for
computing the display bpp, used for bandwidth calculation. Adjust to use
the same register as used by exec_clkcmp and nv50_disp_intr_unk20_2_dp.
Reported-by: Torsten Wagner <torsten.wagner@gmail.com>
Reported-by: Michael Gulick <mgulick@mathworks.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67628
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
commit 8613e7314a
Author: Ben Skeggs <bskeggs@redhat.com>
Date: Mon Oct 21 08:50:25 2013 +1000
drm/nouveau/fb: remove ram oclass argument from base fb constructor
Introduced a unfortunate regression by using nv10 ram oclass for nv1a
hardware, causing corruption and eventually system lockup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74866
Reported-by: John F. Godfrey <jfgodfrey@gmail.com>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit ea7dce901 ("drm/nv50/gr: print mpc trap name when it's not an mp
trap") added an nv_error call that was missing the priv parameter. This
causes GPFs if the error is ever hit.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Address of the ENG_RUNLIST register should be 0x002284 + (engine * 8),
not 0x002284 + (engine * 4).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
See https://bugs.freedesktop.org/show_bug.cgi?id=74492
Reported-by: Ronald <ronald645@gmail.com>
Suggested-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since commit 0fa9061ae8 ("drm/nouveau/mc: handle irq-related setup
ourselves"), drm_device->irq_enabled remained unset. This is needed in
order to properly wait for a vblank event in the generic drm code.
See https://bugs.freedesktop.org/show_bug.cgi?id=74195
Reported-by: Jan Janecek <janjanjanx@gmail.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.
Fixes: 8e0cb8a1f6 ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd9 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Issuing set_termios() from irtty_close() causes kernel Oops for
unplugged usb-serial devices.
Since no other tty_ldisc calls set_termios() on close and no tty driver
seem to check if tty->device_data is NULL or not on entry to set_termios(),
the only solution I can come up with is to remove the irtty_stop_receiver()
call, which only updates termios.
Signed-off-by: Tommie Gannert <tommie@gannert.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need at least HID_MAX_BUFFER_SIZE (4096) bytes as input buffer. HID
core depends on this as it requires every input report to be at least as
big as advertised.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
aggregator_identifier is used to assign unique aggregator identifiers
to aggregators of a bond during device enslaving.
aggregator_identifier is currently a global variable that is zeroed in
bond_3ad_initialize().
This sequence will lead to duplicate aggregator identifiers for eth1 and eth3:
create bond0
change bond0 mode to 802.3ad
enslave eth0 to bond0 //eth0 gets agg id 1
enslave eth1 to bond0 //eth1 gets agg id 2
create bond1
change bond1 mode to 802.3ad
enslave eth2 to bond1 //aggregator_identifier is reset to 0
//eth2 gets agg id 1
enslave eth3 to bond0 //eth3 gets agg id 2
Fix this by making aggregator_identifier private to the bond.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added STM sensor hub vendor id in HID_SENSOR_HUB_ENUM_QUIRK to
fix report descriptors. These devices uses old FW which uses
logical 0 as minimum. In these, HID reports are not using proper
collection classes. So we need to fix report descriptors,for
such devices. This will not have any impact, if the FW uses
logical 1 as minimum.
We look for usage id for "power and report state", and modify
logical minimum value to 1.
This is a follow-up patch to commit id 875e36f8.
Signed-off-by: Archana Patni <archana.patni@linux.intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the device is not completely shut down.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, the "cat /sys/class/net/ethN/operstate" shows
"unknown", and "ethtool ethN" shows "Link detected: yes", when VM
boots up with or without vNIC connected.
This patch fixed the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix booting on PPC boards. Changes to of_match_node matching caused
the serial port on some PPC boards to stop working. Reverted the
change and reimplement to split matching between new style compatible
only matching and fallback to old matching algorithm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTABFuAAoJEMhvYp4jgsXi2PkH/1F9qpuZ1MAHCqu5scBbozKt
LST0Q2qfspl+PjEN30D2X4S6O0qhHeEjeC96AfNUqpJ6sDLws/XcTlfG3niszebi
ldJHnLp4lOJHBby0XtYjyQTyfBnJUYzTfau6DfqpjhZa0ljUHCrbPjvjrp+mqblL
LNmwlK3dzc9dTo925v3R6R+v6Zn5o2Fe9SrQIdNSBCVbJYLDIRK6qhRrI1fJaBwn
rNjf6Bwlt5XJFR8hw9MYUmUQH6bBIhhQGbDKJwnGPaqTDCMXUcRj9KC0HEpOAiJU
h2xROVs8dlnBSyKq/QTlVP2b8AHPNHt4p4HkmIuJFkEJHrnv0iy86ssKROt2dO4=
=j9kb
-----END PGP SIGNATURE-----
Merge tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
"Fix booting on PPC boards. Changes to of_match_node matching caused
the serial port on some PPC boards to stop working. Reverted the
change and reimplement to split matching between new style compatible
only matching and fallback to old matching algorithm"
* tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: search the best compatible match first in __of_match_node()
Revert "OF: base: match each node compatible against all given matches first"
When an error occurs in the port initialization loop, currently the
driver tries to cleanup all the ports. This results in a NULL pointer
dereference if the ports were only partially initialized.
Fix this by updating only the number of initialized ports (either
with failure or successfully), before jumping to the error path
and looping over that number in the cleanup loop.
Cc: Andrew Lunn <andrew@lunn.ch>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Currently, of_match_node compares each given match against all node's
compatible strings with of_device_is_compatible.
To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and also
an alphabetical ordering is more sane there.
Therefore, this patch introduces a function to match each of the node's
compatible strings against all given compatible matches without type and
name first, before checking the next compatible string. This implies
that node's compatibles are ordered from specific to generic while
given matches can be in any order. If we fail to find such a match
entry, then fall-back to the old method in order to keep compatibility.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time to v3.14-rc1 related changes. Also
included is one fix for a free after use regression in persistent
reservations UNREGISTER logic that is CC'ed to >= v3.11.y stable"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix protection copy routine
IB/srpt: replace strict_strtoul() with kstrtoul()
target: Simplify command completion by removing CMD_T_FAILED flag
iser-target: Fix leak on failure in isert_conn_create_fastreg_pool
iscsi-target: Fix SNACK Type 1 + BegRun=0 handling
target: Fix missing length check in spc_emulate_evpd_83()
qla2xxx: Remove last vestiges of qla_tgt_cmd.cmd_list
target: Fix 32-bit + CONFIG_LBDAF=n link error w/ sector_div
target: Fix free-after-use regression in PR unregister
Pull i2c fixes from Wolfram Sang:
"i2c has a bugfix and documentation improvements for you"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Documentation: i2c: mention ACPI method for instantiating devices
Documentation: i2c: describe devicetree method for instantiating devices
i2c: mv64xxx: refactor message start to ensure proper initialization
Pull timer fixes from Thomas Gleixner:
"The following trilogy of patches brings you:
- fix for a long standing math overflow issue with HZ < 60
- an onliner fix for a corner case in the dreaded tick broadcast
mechanism affecting a certain range of AMD machines which are
infested with the infamous automagic C1E power control misfeature
- a fix for one of the ARM platforms which allows the kernel to
proceed and boot instead of stupidly panicing for no good reason.
The patch is slightly larger than necessary, but it's less ugly
than the alternative 5 liner"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Clear broadcast pending bit when switching to oneshot
clocksource: Kona: Print warning rather than panic
time: Fix overflow when HZ is smaller than 60
Rafael J. Wysocki
Dirk Brandewie
Shuah Khan
Greg Kroah-Hartman
Linus Torvalds
Jiang Liu
David Howells
Daniel Mack
Josh Cartwright
Andrzej Pietrasiewicz
Peter Chen
Joerg Roedel
Grant Likely
Kevin Hao
Aaron Lu
Hans de Goede
Geert Uytterhoeven
Lee Jones
Mark Brown
Srivatsa S. Bhat
viresh kumar
Guenter Roeck
Ben Dooks
Thomas Petazzoni
Russell King
Dave Airlie
David S. Miller
Kishon Vijay Abraham I
Richard Weinberger
Aleksander Morgado
Alan Stern
Alex Deucher
Christian König
Dan Carpenter
Chao Bi
Florian Fainelli
Sachin Kamat
Roger Quadros
Ajay Kumar Gupta
Felipe Balbi
Levente Kurusa
Tomasz Nowicki
Masanari Iida
Ilia Mirkin
Emil Velikov
Alexandre Courbot
Tommie Gannert
John W. Linville
David Herrmann
Jiri Bohac
Emil Goode
Archana Patni
Daniel Borkmann
Ingo Molnar
Haiyang Zhang
Ezequiel Garcia