Switchdev support can be disabled at compile time, and in that case,
struct sk_buff will not contain the offload_fwd_mark field.
To make the code in br_forward.c work in both cases, we do what is done
in other places and we create a helper function, with an empty shim
definition, that is implemented by the br_switchdev.o translation module.
This is always compiled if and only if CONFIG_NET_SWITCHDEV is y or m.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 472111920f ("net: bridge: switchdev: allow the TX data plane forwarding to be offloaded")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switchdevs to forward frames from the CPU in accordance with the
bridge configuration in the same way as is done between bridge
ports. This means that the bridge will only send a single skb towards
one of the ports under the switchdev's control, and expects the driver
to deliver the packet to all eligible ports in its domain.
Primarily this improves the performance of multicast flows with
multiple subscribers, as it allows the hardware to perform the frame
replication.
The basic flow between the driver and the bridge is as follows:
- When joining a bridge port, the switchdev driver calls
switchdev_bridge_port_offload() with tx_fwd_offload = true.
- The bridge sends offloadable skbs to one of the ports under the
switchdev's control using skb->offload_fwd_mark = true.
- The switchdev driver checks the skb->offload_fwd_mark field and lets
its FDB lookup select the destination port mask for this packet.
v1->v2:
- convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long
- introduce a static key "br_switchdev_fwd_offload_used" to minimize the
impact of the newly introduced feature on all the setups which don't
have hardware that can make use of it
- introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache
line access
- reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in
__br_forward()
- do not strip VLAN on egress if forwarding offload on VLAN-aware bridge
is being used
- propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP
v2->v3:
- replace the solution based on .ndo_dfwd_add_station with a solution
based on switchdev_bridge_port_offload
- rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD
v3->v4: rebase
v4->v5:
- make sure the static key is decremented on bridge port unoffload
- more function and variable renaming and comments for them:
br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload
br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload
nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom
nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload
fwd_accel to tx_fwd_offload
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 4f2673b3a2 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hwdoms have only been used thus far for equality comparisons, the
bridge has used the simplest possible assignment policy; using a
counter to keep track of the last value handed out.
With the upcoming transmit offloading, we need to perform set
operations efficiently based on hwdoms, e.g. we want to answer
questions like "has this skb been forwarded to any port within this
hwdom?"
Move to a bitmap-based allocation scheme that recycles hwdoms once all
members leaves the bridge. This means that we can use a single
unsigned long to keep track of the hwdoms that have received an skb.
v1->v2: convert the typedef DECLARE_BITMAP(br_hwdom_map_t, BR_HWDOM_MAX)
into a plain unsigned long.
v2->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, four related - but distinct - concepts where named
offload_fwd_mark:
- skb->offload_fwd_mark: Set by the switchdev driver if the underlying
hardware has already forwarded this frame to the other ports in the
same hardware domain.
- nbp->offload_fwd_mark: An idetifier used to group ports that share
the same hardware forwarding domain.
- br->offload_fwd_mark: Counter used to make sure that unique IDs are
used in cases where a bridge contains ports from multiple hardware
domains.
- skb->cb->offload_fwd_mark: The hardware domain on which the frame
ingressed and was forwarded.
Introduce the term "hardware forwarding domain" ("hwdom") in the
bridge to denote a set of ports with the following property:
If an skb with skb->offload_fwd_mark set, is received on a port
belonging to hwdom N, that frame has already been forwarded to all
other ports in hwdom N.
By decoupling the name from "offload_fwd_mark", we can extend the
term's definition in the future - e.g. to add constraints that
describe expected egress behavior - without overloading the meaning of
"offload_fwd_mark".
- nbp->offload_fwd_mark thus becomes nbp->hwdom.
- br->offload_fwd_mark becomes br->last_hwdom.
- skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight
change in naming here mandates a slight change in behavior of the
nbp_switchdev_frame_mark() function. Previously, it only set this
value in skb->cb for packets with skb->offload_fwd_mark true (ones
which were forwarded in hardware). Whereas now we always track the
incoming hwdom for all packets coming from a switchdev (even for the
packets which weren't forwarded in hardware, such as STP BPDUs, IGMP
reports etc). As all uses of skb->cb->offload_fwd_mark were already
gated behind checks of skb->offload_fwd_mark, this will not introduce
any functional change, but it paves the way for future changes where
the ingressing hwdom must be known for frames coming from a switchdev
regardless of whether they were forwarded in hardware or not
(basically, if the skb comes from a switchdev, skb->cb->src_hwdom now
always tracks which one).
A typical example where this is relevant: the switchdev has a fixed
configuration to trap STP BPDUs, but STP is not running on the bridge
and the group_fwd_mask allows them to be forwarded. Say we have this
setup:
br0
/ | \
/ | \
swp0 swp1 swp2
A BPDU comes in on swp0 and is trapped to the CPU; the driver does not
set skb->offload_fwd_mark. The bridge determines that the frame should
be forwarded to swp{1,2}. It is imperative that forward offloading is
_not_ allowed in this case, as the source hwdom is already "poisoned".
Recording the source hwdom allows this case to be handled properly.
v2->v3: added code comments
v3->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding bridge multicast context support for host-joined groups is easy
because we only need the proper timer value. We pass the already chosen
context and use its timer value.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new global vlan option which controls whether multicast snooping
is enabled or disabled for a single vlan. It controls the vlan private
flag: BR_VLFLAG_GLOBAL_MCAST_ENABLED.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vlan options dump flag which causes only global vlan options
to be dumped. The dumps are done only with bridge devices, ports are
ignored. They support vlan compression if the options in sequential
vlans are equal (currently always true).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can have two types of vlan options depending on context:
- per-device vlan options (split in per-bridge and per-port)
- global vlan options
The second type wasn't supported in the bridge until now, but we need
them for per-vlan multicast support, per-vlan STP support and other
options which require global vlan context. They are contained in the global
bridge vlan context even if the vlan is not configured on the bridge device
itself. This patch adds initial netlink attributes and support for setting
these global vlan options, they can only be set (RTM_NEWVLAN) and the
operation must use the bridge device. Since there are no such options yet
it shouldn't have any functional effect.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the port multicast context to check if the router port is a vlan and
in case it is include its vlan id in the notification.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers which check if the current bridge/port multicast context
should be used (i.e. they're not disabled) and use them for Rx IGMP/MLD
processing, timers and new group addition. It is important for vlans to
disable processing of timer/packet after the multicast_lock is obtained
if the vlan context doesn't have BR_VLFLAG_MCAST_ENABLED. There are two
cases when that flag is missing:
- if the vlan is getting destroyed it will be removed and timers will
be stopped
- if the vlan mcast snooping is being disabled
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a global knob that controls if vlan multicast snooping is enabled.
The proper contexts (vlan or bridge-wide) will be chosen based on the knob
when processing packets and changing bridge device state. Note that
vlans have their individual mcast snooping enabled by default, but this
knob is needed to turn on bridge vlan snooping. It is disabled by
default. To enable the knob vlan filtering must also be enabled, it
doesn't make sense to have vlan mcast snooping without vlan filtering
since that would lead to inconsistencies. Disabling vlan filtering will
also automatically disable vlan mcast snooping.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to enable/disable vlan multicast based on its flags, we need
two flags because we need to know if the vlan has multicast enabled
globally (user-controlled) and if it has it enabled on the specific device
(bridge or port). The new private vlan flags are:
- BR_VLFLAG_MCAST_ENABLED: locally enabled multicast on the device, used
when removing a vlan, toggling vlan mcast snooping and controlling
single vlan (kernel-controlled, valid under RTNL and multicast_lock)
- BR_VLFLAG_GLOBAL_MCAST_ENABLED: globally enabled multicast for the
vlan, used to control the bridge-wide vlan mcast snooping for a
single vlan (user-controlled, can be checked under any context)
Bridge vlan contexts are created with multicast snooping enabled by
default to be in line with the current bridge snooping defaults. In
order to actually activate per vlan snooping and context usage a
bridge-wide knob will be added later which will default to disabled.
If that knob is enabled then automatically all vlan snooping will be
enabled. All vlan contexts are initialized with the current bridge
multicast context defaults.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add global and per-port vlan multicast context, only initialized but
still not used. No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass multicast context pointers to multicast functions instead of bridge/port.
This would make it easier later to switch these contexts to their per-vlan
versions. The patch is basically search and replace, no functional changes.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the bridge's global multicast context into a separate
structure which will later be used for per-vlan global context.
No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the port's multicast context into a separate structure which
will later be shared for per-port,vlan context. No functional changes
intended. We need the structure even if bridge multicast is not defined
to pass down as pointer to forwarding functions.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat addresses added to the bridge itself in the same way as regular
ports and send out a notification so that drivers may sync it down to
the hardware FDB.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch fixes a tunnel_dst null pointer dereference due to lockless
access in the tunnel egress path. When deleting a vlan tunnel the
tunnel_dst pointer is set to NULL without waiting a grace period (i.e.
while it's still usable) and packets egressing are dereferencing it
without checking. Use READ/WRITE_ONCE to annotate the lockless use of
tunnel_id, use RCU for accessing tunnel_dst and make sure it is read
only once and checked in the egress path. The dst is already properly RCU
protected so we don't need to do anything fancy than to make sure
tunnel_id and tunnel_dst are read only once and checked in the egress path.
Cc: stable@vger.kernel.org
Fixes: 11538d039a ("bridge: vlan dst_metadata hooks in ingress and egress paths")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast_is_router takes two arguments when bridge IGMP is enabled
and just one when it's disabled, fix the stub to take two as well.
Fixes: 1a3065a268 ("net: bridge: mcast: prepare is-router function for mcast router split")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
A multicast router for IPv4 does not imply that the same host also is a
multicast router for IPv6 and vice versa.
To reduce multicast traffic when a host is only a multicast router for
one of these two protocol families, keep router state for IPv4 and IPv6
separately. Similar to how querier state is kept separately.
For backwards compatibility for netlink and switchdev notifications
these two will still only notify if a port switched from either no
IPv4/IPv6 multicast router to any IPv4/IPv6 multicast router or the
other way round. However a full netlink MDB router dump will now also
include a multicast router timeout for both IPv4 and IPv6.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants make br_multicast_is_router() protocol
family aware.
Note that for now br_ip6_multicast_is_router() uses the currently still
common ip4_mc_router_timer for now. It will be renamed to
ip6_mc_router_timer later when the split is performed.
While at it also renames the "1" and "2" constants in
br_multicast_is_router() to the MDB_RTR_TYPE_TEMP_QUERY and
MDB_RTR_TYPE_PERM enums.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants and to avoid IPv6 #ifdef clutter later add
two wrapper functions for router node retrieval in the payload
forwarding code.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants, rename the affected variable to the IPv4
version first to avoid some renames in later commits.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet switches might only be able to support disabling multicast
snooping globally, which is an issue for example when several bridges
span the same physical device and request contradictory settings.
Propagate the return value of br_mc_disabled_update() such that this
limitation is transmitted correctly to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the VLAN settings of the bridge and the port, the bridge can
either add or remove a tag. When vlan filtering is enabled, the fdb lookup
also needs to know the VLAN tag/proto for the destination address
To provide this, keep track of the stack of VLAN tags for the path in the
lookup context
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prototype of br_vlan_filter_toggle was updated to include a netlink
extack, but the stub definition wasn't, which results in a build error
when CONFIG_BRIDGE_VLAN_FILTERING=n.
Fixes: 9e781401cb ("net: bridge: propagate extack through store_bridge_parm")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The benefit is the ability to propagate errors from switchdev drivers
for the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL attributes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge sysfs interface stores parameters for the STP, VLAN,
multicast etc subsystems using a predefined function prototype.
Sometimes the underlying function being called supports a netlink
extended ack message, and we ignore it.
Let's expand the store_bridge_parm function prototype to include the
extack, and just print it to console, but at least propagate it where
applicable. Where not applicable, create a shim function in the
br_sysfs_br.c file that discards the extra function argument.
This patch allows us to propagate the extack argument to
br_vlan_set_default_pvid, br_vlan_set_proto and br_vlan_filter_toggle,
and from there, further up in br_changelink from br_netlink.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is identical with br_vlan_filter_toggle.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the netlink interface, propagate errors through extack rather than
simply printing them to the console. For the sysfs interface, we still
print to the console, but at least that's one layer higher than in
switchdev, which also allows us to silently ignore the offloading of
flags if that is ever needed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a default limit of 512 for number of tracked EHT hosts per-port.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mark groups which were deleted due to fast leave/EHT.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for IGMPv3/MLDv2 allow/block EHT handling. Similar to how
the reports are processed we have 2 cases when the group is in include
or exclude mode, these are processed as follows:
- group include
- allow: create missing entries
- block: remove existing matching entries and remove the corresponding
S,G entries if there are no more set host entries, then possibly
delete the whole group if there are no more S,G entries
- group exclude
- allow
- host include: create missing entries
- host exclude: remove existing matching entries and remove the
corresponding S,G entries if there are no more set host entries
- block
- host include: remove existing matching entries and remove the
corresponding S,G entries if there are no more set host entries,
then possibly delete the whole group if there are no more S,G entries
- host exclude: create missing entries
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add EHT structures for tracking hosts and sources per group. We keep one
set for each host which has all of the host's S,G entries, and one set for
each multicast source which has all hosts that have joined that S,G. For
each host, source entry we record the filter_mode and we keep an expiry
timer. There is also one global expiry timer per source set, it is
updated with each set entry update, it will be later used to lower the
set's timer instead of lowering each entry's timer separately.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When enabling multicast snooping, bridge module deadlocks on multicast_lock
if 1) IPv6 is enabled, and 2) there is an existing querier on the same L2
network.
The deadlock was caused by the following sequence: While holding the lock,
br_multicast_open calls br_multicast_join_snoopers, which eventually causes
IP stack to (attempt to) send out a Listener Report (in igmp6_join_group).
Since the destination Ethernet address is a multicast address, br_dev_xmit
feeds the packet back to the bridge via br_multicast_rcv, which in turn
calls br_multicast_add_group, which then deadlocks on multicast_lock.
The fix is to move the call br_multicast_join_snoopers outside of the
critical section. This works since br_multicast_join_snoopers only deals
with IP and does not modify any multicast data structures of the bridge,
so there's no need to hold the lock.
Steps to reproduce:
1. sysctl net.ipv6.conf.all.force_mld_version=1
2. have another querier
3. ip link set dev bridge type bridge mcast_snooping 0 && \
ip link set dev bridge type bridge mcast_snooping 1 < deadlock >
A typical call trace looks like the following:
[ 936.251495] _raw_spin_lock+0x5c/0x68
[ 936.255221] br_multicast_add_group+0x40/0x170 [bridge]
[ 936.260491] br_multicast_rcv+0x7ac/0xe30 [bridge]
[ 936.265322] br_dev_xmit+0x140/0x368 [bridge]
[ 936.269689] dev_hard_start_xmit+0x94/0x158
[ 936.273876] __dev_queue_xmit+0x5ac/0x7f8
[ 936.277890] dev_queue_xmit+0x10/0x18
[ 936.281563] neigh_resolve_output+0xec/0x198
[ 936.285845] ip6_finish_output2+0x240/0x710
[ 936.290039] __ip6_finish_output+0x130/0x170
[ 936.294318] ip6_output+0x6c/0x1c8
[ 936.297731] NF_HOOK.constprop.0+0xd8/0xe8
[ 936.301834] igmp6_send+0x358/0x558
[ 936.305326] igmp6_join_group.part.0+0x30/0xf0
[ 936.309774] igmp6_group_added+0xfc/0x110
[ 936.313787] __ipv6_dev_mc_inc+0x1a4/0x290
[ 936.317885] ipv6_dev_mc_inc+0x10/0x18
[ 936.321677] br_multicast_open+0xbc/0x110 [bridge]
[ 936.326506] br_multicast_toggle+0xec/0x140 [bridge]
Fixes: 4effd28c12 ("bridge: join all-snoopers multicast address")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20201204235628.50653-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netdev->tstats instead of a member of net_bridge for storing
a pointer to the per-cpu counters. This allows us to use core
functionality for statistics handling.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/9bad2be2-fd84-7c6e-912f-cee433787018@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Struct br_vlan_stats duplicates pcpu_sw_netstats (apart from
br_vlan_stats not defining an alignment requirement), therefore
switch to using the latter one.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/04d25c3d-c5f6-3611-6d37-c2f40243dae2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace list_head with hlist_head for MRP list under the bridge.
There is no need for a circular list when a linear list will work.
This will also decrease the size of 'struct net_bridge'.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20201106215049.1448185-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit cited below has changed only the functional prototype of
br_multicast_querier_exists, but forgot to do that for the stub
prototype (the one where CONFIG_BRIDGE_IGMP_SNOOPING is disabled).
Fixes: 955062b03f ("net: bridge: mcast: add support for raw L2 multicast groups")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201101000845.190009-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the bridge multicast control and data path to configure routes
for L2 (non-IP) multicast groups.
The uapi struct br_mdb_entry union u is extended with another variant,
mac_addr, which does not change the structure size, and which is valid
when the proto field is zero.
To be compatible with the forwarding code that is already in place,
which acts as an IGMP/MLD snooping bridge with querier capabilities, we
need to declare that for L2 MDB entries (for which there exists no such
thing as IGMP/MLD snooping/querying), that there is always a querier.
Otherwise, these entries would be flooded to all bridge ports and not
just to those that are members of the L2 multicast group.
Needless to say, only permanent L2 multicast groups can be installed on
a bridge port.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201028233831.610076-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the implementation of Netlink notifications out of CFM.
Notifications are initiated whenever a state change happens in CFM.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_STATUS_INFO:
This indicate that the MEP instance status are following.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO:
This indicate that the peer MEP status are following.
CFM nested attribute has the following attributes in next level.
IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected Opcode.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected version.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN:
The MEP instance received CCM PDU with MD level lower than
configured level. This frame is discarded.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID:
The added Peer MEP ID of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT:
The CCM defect status.
The type is NLA_U32 (bool).
True means no CCM frame is received for 3.25 intervals.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI:
The last received CCM PDU RDI.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE:
The last received CCM PDU Port Status TLV value field.
The type is NLA_U8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE:
The last received CCM PDU Interface Status TLV value field.
The type is NLA_U8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN:
A CCM frame has been received from Peer MEP.
The type is NLA_U32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN:
A CCM frame with TLV has been received from Peer MEP.
The type is NLA_U32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN:
A CCM frame with unexpected sequence number has been received
from Peer MEP.
The type is NLA_U32 (bool).
When a sequence number is not one higher than previously received
then it is unexpected.
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the implementation of CFM netlink status
get information interface.
Add new nested netlink attributes. These attributes are used by the
user space to get status information.
GETLINK:
Request filter RTEXT_FILTER_CFM_STATUS:
Indicating that CFM status information must be delivered.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_STATUS_INFO:
This indicate that the MEP instance status are following.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO:
This indicate that the peer MEP status are following.
CFM nested attribute has the following attributes in next level.
GETLINK RTEXT_FILTER_CFM_STATUS:
IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected Opcode.
The type is u32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected version.
The type is u32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN:
The MEP instance received CCM PDU with MD level lower than
configured level. This frame is discarded.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID:
The added Peer MEP ID of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT:
The CCM defect status.
The type is u32 (bool).
True means no CCM frame is received for 3.25 intervals.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI:
The last received CCM PDU RDI.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE:
The last received CCM PDU Port Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE:
The last received CCM PDU Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN:
A CCM frame has been received from Peer MEP.
The type is u32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN:
A CCM frame with TLV has been received from Peer MEP.
The type is u32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN:
A CCM frame with unexpected sequence number has been received
from Peer MEP.
The type is u32 (bool).
When a sequence number is not one higher than previously received
then it is unexpected.
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the implementation of CFM netlink configuration
get information interface.
Add new nested netlink attributes. These attributes are used by the
user space to get configuration information.
GETLINK:
Request filter RTEXT_FILTER_CFM_CONFIG:
Indicating that CFM configuration information must be delivered.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_CREATE_INFO:
This indicate that MEP instance create parameters are following.
IFLA_BRIDGE_CFM_MEP_CONFIG_INFO:
This indicate that MEP instance config parameters are following.
IFLA_BRIDGE_CFM_CC_CONFIG_INFO:
This indicate that MEP instance CC functionality
parameters are following.
IFLA_BRIDGE_CFM_CC_RDI_INFO:
This indicate that CC transmitted CCM PDU RDI
parameters are following.
IFLA_BRIDGE_CFM_CC_CCM_TX_INFO:
This indicate that CC transmitted CCM PDU parameters are
following.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INFO:
This indicate that the added peer MEP IDs are following.
CFM nested attribute has the following attributes in next level.
GETLINK RTEXT_FILTER_CFM_CONFIG:
IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE:
The created MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN:
The created MEP domain.
The type is u32 (br_cfm_domain).
It must be BR_CFM_PORT.
This means that CFM frames are transmitted and received
directly on the port - untagged. Not in a VLAN.
IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION:
The created MEP direction.
The type is u32 (br_cfm_mep_direction).
It must be BR_CFM_MEP_DIRECTION_DOWN.
This means that CFM frames are transmitted and received on
the port. Not in the bridge.
IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX:
The created MEP residence port ifindex.
The type is u32 (ifindex).
IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE:
The deleted MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC:
The configured MEP unicast MAC address.
The type is 6*u8 (array).
This is used as SMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL:
The configured MEP unicast MD level.
The type is u32.
It must be in the range 1-7.
No CFM frames are passing through this MEP on lower levels.
IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID:
The configured MEP ID.
The type is u32.
It must be in the range 0-0x1FFF.
This MEP ID is inserted in any transmitted CCM frame.
IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE:
The Continuity Check (CC) functionality is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL:
The CC expected receive interval of CCM frames.
The type is u32 (br_cfm_ccm_interval).
This is also the transmission interval of CCM frames when enabled.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID:
The CC expected receive MAID in CCM frames.
The type is CFM_MAID_LENGTH*u8.
This is MAID is also inserted in transmitted CCM frames.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_MEPID:
The CC Peer MEP ID added.
The type is u32.
When a Peer MEP ID is added and CC is enabled it is expected to
receive CCM frames from that Peer MEP.
IFLA_BRIDGE_CFM_CC_RDI_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_RDI_RDI:
The RDI that is inserted in transmitted CCM PDU.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC:
The transmitted CCM frame destination MAC address.
The type is 6*u8 (array).
This is used as DMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE:
The transmitted CCM frame update (increment) of sequence
number is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD:
The period of time where CCM frame are transmitted.
The type is u32.
The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX
must be done before timeout to keep transmission alive.
When period is zero any ongoing CCM frame transmission
will be stopped.
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV:
The transmitted CCM frame update with Interface Status TLV
is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE:
The transmitted Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV:
The transmitted CCM frame update with Port Status TLV is enabled
or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE:
The transmitted Port Status TLV value field.
The type is u8.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the implementation of CFM netlink configuration
set information interface.
Add new nested netlink attributes. These attributes are used by the
user space to create/delete/configure CFM instances.
SETLINK:
IFLA_BRIDGE_CFM:
Indicate that the following attributes are CFM.
IFLA_BRIDGE_CFM_MEP_CREATE:
This indicate that a MEP instance must be created.
IFLA_BRIDGE_CFM_MEP_DELETE:
This indicate that a MEP instance must be deleted.
IFLA_BRIDGE_CFM_MEP_CONFIG:
This indicate that a MEP instance must be configured.
IFLA_BRIDGE_CFM_CC_CONFIG:
This indicate that a MEP instance Continuity Check (CC)
functionality must be configured.
IFLA_BRIDGE_CFM_CC_PEER_MEP_ADD:
This indicate that a CC Peer MEP must be added.
IFLA_BRIDGE_CFM_CC_PEER_MEP_REMOVE:
This indicate that a CC Peer MEP must be removed.
IFLA_BRIDGE_CFM_CC_CCM_TX:
This indicate that the CC transmitted CCM PDU must be configured.
IFLA_BRIDGE_CFM_CC_RDI:
This indicate that the CC transmitted CCM PDU RDI must be
configured.
CFM nested attribute has the following attributes in next level.
SETLINK RTEXT_FILTER_CFM_CONFIG:
IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE:
The created MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN:
The created MEP domain.
The type is u32 (br_cfm_domain).
It must be BR_CFM_PORT.
This means that CFM frames are transmitted and received
directly on the port - untagged. Not in a VLAN.
IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION:
The created MEP direction.
The type is u32 (br_cfm_mep_direction).
It must be BR_CFM_MEP_DIRECTION_DOWN.
This means that CFM frames are transmitted and received on
the port. Not in the bridge.
IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX:
The created MEP residence port ifindex.
The type is u32 (ifindex).
IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE:
The deleted MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC:
The configured MEP unicast MAC address.
The type is 6*u8 (array).
This is used as SMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL:
The configured MEP unicast MD level.
The type is u32.
It must be in the range 1-7.
No CFM frames are passing through this MEP on lower levels.
IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID:
The configured MEP ID.
The type is u32.
It must be in the range 0-0x1FFF.
This MEP ID is inserted in any transmitted CCM frame.
IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE:
The Continuity Check (CC) functionality is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL:
The CC expected receive interval of CCM frames.
The type is u32 (br_cfm_ccm_interval).
This is also the transmission interval of CCM frames when enabled.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID:
The CC expected receive MAID in CCM frames.
The type is CFM_MAID_LENGTH*u8.
This is MAID is also inserted in transmitted CCM frames.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_MEPID:
The CC Peer MEP ID added.
The type is u32.
When a Peer MEP ID is added and CC is enabled it is expected to
receive CCM frames from that Peer MEP.
IFLA_BRIDGE_CFM_CC_RDI_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_RDI_RDI:
The RDI that is inserted in transmitted CCM PDU.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC:
The transmitted CCM frame destination MAC address.
The type is 6*u8 (array).
This is used as DMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE:
The transmitted CCM frame update (increment) of sequence
number is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD:
The period of time where CCM frame are transmitted.
The type is u32.
The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX
must be done before timeout to keep transmission alive.
When period is zero any ongoing CCM frame transmission
will be stopped.
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV:
The transmitted CCM frame update with Interface Status TLV
is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE:
The transmitted Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV:
The transmitted CCM frame update with Port Status TLV is enabled
or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE:
The transmitted Port Status TLV value field.
The type is u8.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the first commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
It contains MEP instance create, delete and configuration.
Connectivity Fault Management (CFM) comprises capabilities for
detecting, verifying, and isolating connectivity failures in
Virtual Bridged Networks. These capabilities can be used in
networks operated by multiple independent organizations, each
with restricted management access to each others equipment.
CFM functions are partitioned as follows:
- Path discovery
- Fault detection
- Fault verification and isolation
- Fault notification
- Fault recovery
Interface consists of these functions:
br_cfm_mep_create()
br_cfm_mep_delete()
br_cfm_mep_config_set()
br_cfm_cc_config_set()
br_cfm_cc_peer_mep_add()
br_cfm_cc_peer_mep_remove()
A MEP instance is created by br_cfm_mep_create()
-It is the Maintenance association End Point
described in 802.1Q section 19.2.
-It is created on a specific level (1-7) and is assuring
that no CFM frames are passing through this MEP on lower levels.
-It initiates and validates CFM frames on its level.
-It can only exist on a port that is related to a bridge.
-Attributes given cannot be changed until the instance is
deleted.
A MEP instance can be deleted by br_cfm_mep_delete().
A created MEP instance has attributes that can be
configured by br_cfm_mep_config_set().
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check Receiver state machine can be
enabled and disabled.
According to 802.1Q section 19.2.8
A MEP can have Peer MEPs added and removed by
br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove()
The Continuity Check feature can maintain connectivity
status on each added Peer MEP.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This makes it possible to include or exclude the CFM
protocol according to 802.1Q section 12.14.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean
Tobias Waldekranz
Nikolay Aleksandrov
Jakub Kicinski
Linus Lüssing
Florian Fainelli
Felix Fietkau
Joseph Huang
Heiner Kallweit
Horatiu Vultur
Henrik Bjoernlund