Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xen frontends shouldn't BUG() in case of illegal data received from
their backends. So replace the BUG_ON()s when reading illegal data from
the ring page with negative return values.
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20210707091045.460-1-jgross@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Elkhart Lake UARTs are PCI enumerated Synopsys DesignWare v4.0+ UART
integrated with Intel iDMA 32-bit DMA controller. There is a specific
driver to handle them, i.e. 8250_lpss. Hence, disable 8250_pci
enumeration for these UARTs.
Fixes: 1b91d97c66 ("serial: 8250_lpss: Add ->setup() for Elkhart Lake ports")
Fixes: 4f912b898d ("serial: 8250_lpss: Enable HS UART on Elkhart Lake")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713101739.36962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Add back an irqrestore-version of the sysrq port-unlock helper and use
it in the 8250 callbacks that need it.
Fixes: 75f4e830fa ("serial: do not restore interrupt state in sysrq helper")
Cc: stable@vger.kernel.org # 5.13
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210714080427.28164-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra serial driver always prints an error message when enabling the
FIFO for devices that have support for checking the FIFO enable status.
Fix this by displaying the error message, only when an error occurs.
Finally, update the error message to make it clear that enabling the
FIFO failed and display the error code.
Fixes: 222dcdff34 ("serial: tegra: check for FIFO mode enabled status")
Cc: <stable@vger.kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210630125643.264264-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In one error case the clock may be left prepared and enabled.
Unprepare and disable clock in that case to balance state of
the hardware.
Fixes: d4d6f03c4f ("serial: max310x: Try to get crystal clock rate from property")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210625153733.12911-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'state' variable is only set but never read in amiserial's shutdown.
Drop it.
It was like this since the driver was added to the tree as far as I can
tell.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amiserial deals only with a single serial, so drop the rs_table array
and NR_PORTS and define a single non-array serial_state for simplicity
instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #include directives are in different places in amiserial:
1) there is no reason for that, and
2) it makes hard to judge what is included and what is not.
Therefore, move all the includes to a single place and sort them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"custom" macro is a too generic name. Expand it -- that is use
amiga_custom on all the locations.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a macro (serial_isroot) for capable(CAP_SYS_ADMIN) does not save
us from anything. It rather obfuscates the code. Hence expand
serial_isroot to be explicit like every other driver is.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zeroing each member of struct serial_state in probe is fragile and
overly complicated. Do one memset for them all.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->port is already set when rs_open is called given we linked it by
tty_port_link_device(). If it wasn't, the tty layer would WARN loudly.
So it's pointless to set it in rs_open. Instead, use the value in
tty->port to find out the serial_state (info).
It's a fallout of commit b19e2ca77e (TTY: use tty_port_link_device)
which added tty_port_link_device here, but omitted to remove the
tty->port assignment from rs_open.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's always 1, so define a macro for it instead. Note that the check in
set_serial_info is doubled, hence remove the latter.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment about interrupt routines is stale at least since commit
41c28ff163 (kill _INLINE_) from 2006. So remove the obsolete parts and
leave only "here they start...".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove a print of serial_name and serial_version from the probe
function, i.e. show_serial_version() from amiga_serial_probe(). The
value of such a print is minimal.
Aside from that, the version is artificial (copied from the serial core
in 2.3.45pre2 and never increased). So inline the version into
seq_printf's format string in rs_proc_show() and remove both strings
completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210714091314.8292-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the sake of reducing layering violation add ->unregister_gpio()
callback and use it in the ->exit() one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713095821.7834-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the commit 07e5d4ff12 ("Revert serial-uartlite: Add runtime
support") the runtime pm support was reverted to aid reverting of
the other patches.
This patch adds the runtime PM support back.
The runtime pm calls are used to gate and enable the clocks.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20210713064835.27978-3-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the uart registration fails the clocks are left enabled.
Disable the clock in case of errors.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20210713064835.27978-2-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue happens when a userspace program does an ioctl
FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct
containing only the fields xres, yres, and bits_per_pixel
with values.
If this struct is the same as the previous ioctl, the
vc_resize() detects it and doesn't call the resize_screen(),
leaving the fb_var_screeninfo incomplete. And this leads to
the updatescrollmode() calculates a wrong value to
fbcon_display->vrows, which makes the real_y() return a
wrong value of y, and that value, eventually, causes
the imageblit to access an out-of-bound address value.
To solve this issue I made the resize_screen() be called
even if the screen does not need any resizing, so it will
"fix and fill" the fb_var_screeninfo independently.
Cc: stable <stable@vger.kernel.org> # after 5.15-rc2 is out, give it time to bake
Reported-and-tested-by: syzbot+858dc7a2f7ef07c2c219@syzkaller.appspotmail.com
Signed-off-by: Igor Matheus Andrade Torrente <igormtorrente@gmail.com>
Link: https://lore.kernel.org/r/20210628134509.15895-1-igormtorrente@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is used for TX and RX by serial driver, it should
pass the DMA device pointer to DMA API instead of UART device
pointer. DMA device should be used for DMA API because only
the DMA device is aware of how the device connects to the memory.
There might be an extra level of address translation due to a
SMMU attached to the DMA device. When serial device is used for
DMA API, the DMA API will have no clue of the SMMU attached to
the DMA device.
This patch is necessary to fix the SMMU page faults
which is observed when a DMA(with SMMU enabled) is attached
to UART for transfer.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Link: https://lore.kernel.org/r/20210629045902.48912-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make pl011 work better, multiple interrupts are
required, such as TXIM, RXIM, RTIM, error interrupt(FE/PE/BE/OE);
at the same time, pl011 to GIC does not merge the interrupt
lines(each serial-interrupt corresponding to different GIC hardware
interrupt), so need to enable and request multiple gic interrupt
numbers in the driver.
Signed-off-by: Bing Fan <tombinfan@tencent.com>
Link: https://lore.kernel.org/r/1625103512-30182-1-git-send-email-hptsfb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic support for RS485: Provide a callback to configure RS485
settings. Handle the RS485 specific part in the functions
pl011_rs485_tx_start() and pl011_rs485_tx_stop() which extend the generic
start/stop callbacks.
Beside via IOCTL from userspace RS485 can be enabled by means of the
device tree property "rs485-enabled-at-boot-time".
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20210630225644.3744-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Report extra baud rates supported above the base rate for ports with the
UPF_MAGIC_MULTIPLIER property, so that people have a way to find out
that they can be used with their system, e.g.:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
serial8250.0: ttyS0 extra baud rates supported: 230400, 460800
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS1 extra baud rates supported: 230400, 460800
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Otherwise there is no clear way to figure this out, as the feature is
only reported as an obscure TTY flag in bit 16:
$ cat /sys/class/tty/ttyS[0-2]/flags
0x10010040
0x10010040
0x90000040
$
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260334170.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow more drivers to be compile tested more easily, for example, when
doing subsystem-wide changes.
Verified on X86_64 as well as arm, powerpc and m68k with minimal configs
in order to catch missing implicit build dependencies.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210715083011.18887-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer membase is currently being in initialized with zero rather
than NULL. Fix this.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210719095533.14017-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI-based Loongson boards need configurable rather than fixed clock
frequency for serial ports.
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20210715061637.134436-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate the const array k3_soc_devices on the stack but instead it
static. Makes the object code smaller by 44 bytes:
Before:
text data bss dec hex filename
31628 5609 128 37365 91f5 drivers/tty/serial/8250/8250_omap.o
After:
text data bss dec hex filename
31520 5673 128 37321 91c9 drivers/tty/serial/8250/8250_omap.o
Reduction of 44 bytes
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210715140759.27244-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Support for optimized routines based on the host CPU
- Support for PCI via virtio
- Various fixes
-----BEGIN PGP SIGNATURE-----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=wAww
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
- Support for optimized routines based on the host CPU
- Support for PCI via virtio
- Various fixes
* tag 'for-linus-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: remove unneeded semicolon in um_arch.c
um: Remove the repeated declaration
um: fix error return code in winch_tramp()
um: fix error return code in slip_open()
um: Fix stack pointer alignment
um: implement flush_cache_vmap/flush_cache_vunmap
um: add a UML specific futex implementation
um: enable the use of optimized xor routines in UML
um: Add support for host CPU flags and alignment
um: allow not setting extra rpaths in the linux binary
um: virtio/pci: enable suspend/resume
um: add PCI over virtio emulation driver
um: irqs: allow invoking time-travel handler multiple times
um: time-travel/signals: fix ndelay() in interrupt
um: expose time-travel mode to userspace side
um: export signals_enabled directly
um: remove unused smp_sigio_handler() declaration
lib: add iomem emulation (logic_iomem)
um: allow disabling NO_IOMEM
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM7jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloDQCfZOlLYXF+2KgXJQqevNnRiu7/B1gAn3aCX6xh
UWVUfu5LDIXi2uFERRT1
=Ze3R
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
- Rework inline asm to get rid of error prone "register asm" constructs,
which are problematic especially when code instrumentation is enabled. In
particular introduce and use register pair union to allocate even/odd
register pairs. Unfortunately this breaks compatibility with older
clang compilers and minimum clang version for s390 has been raised to 13.
https://lore.kernel.org/linux-next/CAK7LNARuSmPCEy-ak0erPrPTgZdGVypBROFhtw+=3spoGoYsyw@mail.gmail.com/
- Fix gcc 11 warnings, which triggered various minor reworks all over
the code.
- Add zstd kernel image compression support.
- Rework boot CPU lowcore handling.
- De-duplicate and move kernel memory layout setup logic earlier.
- Few fixes in preparation for FORTIFY_SOURCE performing compile-time
and run-time field bounds checking for mem functions.
- Remove broken and unused power management support leftovers in s390
drivers.
- Disable stack-protector for decompressor and purgatory to fix buildroot
build.
- Fix vt220 sclp console name to match the char device name.
- Enable HAVE_IOREMAP_PROT and add zpci_set_irq()/zpci_clear_irq() in
zPCI code.
- Remove some implausible WARN_ON_ONCEs and remove arch specific counter
transaction call backs in favour of default transaction handling in
perf code.
- Extend/add new uevents for online/config/mode state changes of
AP card / queue device in zcrypt.
- Minor entry and ccwgroup code improvements.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmDhuTEACgkQjYWKoQLX
FBjVlggAgDFBkDjlyfvrm4xzmHi7BJMmhrTJIONsSz+3tcA4/u5kE+Hrdrqxm0Uh
ZH4MXBxn4q4Fmoomhu5w5ZDe8o2ip0aN9fFNdsBoP8hurmQbL/IbdTnBETKMrKpV
XpogU2G7p+2nQ0+9+o6PS/vWlZhI88NVh8dWyRd2+5/XdMycgLv2Qm7NpQoACVw1
CbUvxP2PlpZ0wltLvNBKPg1xXMZa3GS0wbVUsS2jiWcr/3VzCqfTHenZJ/RadoE6
axG99QXCbLDMsJgVQcXtlI8K6Z461fAwbNtWZWC+Uq7o5pYuUFW1dovMg9WWF+7T
lFNqXyyNy5wwITRkvuzjlVTE8yzYYg==
=ADZ4
-----END PGP SIGNATURE-----
Merge tag 's390-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Rework inline asm to get rid of error prone "register asm"
constructs, which are problematic especially when code
instrumentation is enabled.
In particular introduce and use register pair union to allocate
even/odd register pairs. Unfortunately this breaks compatibility with
older clang compilers and minimum clang version for s390 has been
raised to 13.
https://lore.kernel.org/linux-next/CAK7LNARuSmPCEy-ak0erPrPTgZdGVypBROFhtw+=3spoGoYsyw@mail.gmail.com/
- Fix gcc 11 warnings, which triggered various minor reworks all over
the code.
- Add zstd kernel image compression support.
- Rework boot CPU lowcore handling.
- De-duplicate and move kernel memory layout setup logic earlier.
- Few fixes in preparation for FORTIFY_SOURCE performing compile-time
and run-time field bounds checking for mem functions.
- Remove broken and unused power management support leftovers in s390
drivers.
- Disable stack-protector for decompressor and purgatory to fix
buildroot build.
- Fix vt220 sclp console name to match the char device name.
- Enable HAVE_IOREMAP_PROT and add zpci_set_irq()/zpci_clear_irq() in
zPCI code.
- Remove some implausible WARN_ON_ONCEs and remove arch specific
counter transaction call backs in favour of default transaction
handling in perf code.
- Extend/add new uevents for online/config/mode state changes of AP
card / queue device in zcrypt.
- Minor entry and ccwgroup code improvements.
- Other small various fixes and improvements all over the code.
* tag 's390-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (91 commits)
s390/dasd: use register pair instead of register asm
s390/qdio: get rid of register asm
s390/ioasm: use symbolic names for asm operands
s390/ioasm: get rid of register asm
s390/cmf: get rid of register asm
s390/lib,string: get rid of register asm
s390/lib,uaccess: get rid of register asm
s390/string: get rid of register asm
s390/cmpxchg: use register pair instead of register asm
s390/mm,pages-states: get rid of register asm
s390/lib,xor: get rid of register asm
s390/timex: get rid of register asm
s390/hypfs: use register pair instead of register asm
s390/zcrypt: Switch to flexible array member
s390/speculation: Use statically initialized const for instructions
virtio/s390: get rid of open-coded kvm hypercall
s390/pci: add zpci_set_irq()/zpci_clear_irq()
scripts/min-tool-version.sh: Raise minimum clang version to 13.0.0 for s390
s390/ipl: use register pair instead of register asm
s390/mem_detect: fix tprot() program check new psw handling
...
- A big series refactoring parts of our KVM code, and converting some to C.
- Support for ARCH_HAS_SET_MEMORY, and ARCH_HAS_STRICT_MODULE_RWX on some CPUs.
- Support for the Microwatt soft-core.
- Optimisations to our interrupt return path on 64-bit.
- Support for userspace access to the NX GZIP accelerator on PowerVM on Power10.
- Enable KUAP and KUEP by default on 32-bit Book3S CPUs.
- Other smaller features, fixes & cleanups.
Thanks to: Andy Shevchenko, Aneesh Kumar K.V, Arnd Bergmann, Athira Rajeev, Baokun Li,
Benjamin Herrenschmidt, Bharata B Rao, Christophe Leroy, Daniel Axtens, Daniel Henrique
Barboza, Finn Thain, Geoff Levand, Haren Myneni, Jason Wang, Jiapeng Chong, Joel Stanley,
Jordan Niethe, Kajol Jain, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas
Piggin, Nick Desaulniers, Paul Mackerras, Russell Currey, Sathvika Vasireddy, Shaokun
Zhang, Stephen Rothwell, Sudeep Holla, Suraj Jitindar Singh, Tom Rix, Vaibhav Jain,
YueHaibing, Zhang Jianhua, Zhen Lei.
-----BEGIN PGP SIGNATURE-----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=zo4d
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- A big series refactoring parts of our KVM code, and converting some
to C.
- Support for ARCH_HAS_SET_MEMORY, and ARCH_HAS_STRICT_MODULE_RWX on
some CPUs.
- Support for the Microwatt soft-core.
- Optimisations to our interrupt return path on 64-bit.
- Support for userspace access to the NX GZIP accelerator on PowerVM on
Power10.
- Enable KUAP and KUEP by default on 32-bit Book3S CPUs.
- Other smaller features, fixes & cleanups.
Thanks to: Andy Shevchenko, Aneesh Kumar K.V, Arnd Bergmann, Athira
Rajeev, Baokun Li, Benjamin Herrenschmidt, Bharata B Rao, Christophe
Leroy, Daniel Axtens, Daniel Henrique Barboza, Finn Thain, Geoff Levand,
Haren Myneni, Jason Wang, Jiapeng Chong, Joel Stanley, Jordan Niethe,
Kajol Jain, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas
Piggin, Nick Desaulniers, Paul Mackerras, Russell Currey, Sathvika
Vasireddy, Shaokun Zhang, Stephen Rothwell, Sudeep Holla, Suraj Jitindar
Singh, Tom Rix, Vaibhav Jain, YueHaibing, Zhang Jianhua, and Zhen Lei.
* tag 'powerpc-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (218 commits)
powerpc: Only build restart_table.c for 64s
powerpc/64s: move ret_from_fork etc above __end_soft_masked
powerpc/64s/interrupt: clean up interrupt return labels
powerpc/64/interrupt: add missing kprobe annotations on interrupt exit symbols
powerpc/64: enable MSR[EE] in irq replay pt_regs
powerpc/64s/interrupt: preserve regs->softe for NMI interrupts
powerpc/64s: add a table of implicit soft-masked addresses
powerpc/64e: remove implicit soft-masking and interrupt exit restart logic
powerpc/64e: fix CONFIG_RELOCATABLE build warnings
powerpc/64s: fix hash page fault interrupt handler
powerpc/4xx: Fix setup_kuep() on SMP
powerpc/32s: Fix setup_{kuap/kuep}() on SMP
powerpc/interrupt: Use names in check_return_regs_valid()
powerpc/interrupt: Also use exit_must_hard_disable() on PPC32
powerpc/sysfs: Replace sizeof(arr)/sizeof(arr[0]) with ARRAY_SIZE
powerpc/ptrace: Refactor regs_set_return_{msr/ip}
powerpc/ptrace: Move set_return_regs_changed() before regs_set_return_{msr/ip}
powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()
powerpc/pseries/vas: Include irqdomain.h
powerpc: mark local variables around longjmp as volatile
...
Member nb in struct mvebu_uart is not set nor read. So remove it completely.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210624224909.6350-7-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For default (x16) scheme which is currently used by mvebu-uart.c driver,
maximal divisor of UART base clock is 1023*16. Therefore there is limit for
minimal supported baudrate. This change calculate it correctly and prevents
setting invalid divisor 0 into hardware registers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-4-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing mvuart->clk for non-error is not enough as mvuart->clk may contain
valid clk pointer but when clk_prepare_enable(mvuart->clk) failed then
port->uartclk is zero.
When mvuart->clk is not available then port->uartclk is zero too.
Parent clock rate port->uartclk is needed to calculate UART clock divisor
and without it is not possible to change baudrate.
So fix test condition when it is possible to change baudrate.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-3-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checkpatch warnings:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Jinchao Wang <wjc@cdjrlc.com>
Link: https://lore.kernel.org/r/20210624021207.58059-1-wjc@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On K3 family of SoCs (which includes AM654 SoC), it is observed that RX
TIMEOUT is signalled after RX FIFO has been drained, in which case a
dummy read of RX FIFO is required to clear RX TIMEOUT condition.
Otherwise, this would lead to an interrupt storm.
Fix this by introducing UART_RX_TIMEOUT_QUIRK flag and doing a dummy
read in IRQ handler when RX TIMEOUT is reported with no data in RX FIFO.
Fixes: be70874498 ("serial: 8250_omap: Add support for AM654 UART controller")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210622145704.11168-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b61c8bf469. It never
made it to a public mailing list and still needs some work based on the
review comments. So revert it for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/CAMuHMdXA9-ajoAza2JAW5879ECieMm1dbBbKHgJhDa7=3kWu3w@mail.gmail.com
Cc: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Power management support was removed for s390 with
commit 394216275c ("s390: remove broken hibernate / power management
support").
Remove the hvc_iucv_driver, but keep the device struct around so that
it can continue to provide the hvc_iucv_dev_attr_groups attributes.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This check is used in the code on many places. Either in positive or
negative form. So introduce a helper called mxser_16550A_or_MUST for
this purpose. And replace all the occurrences.
This simplifies many ifs in there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-67-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local 'flags' are used to store speed in mxser_set_serial_info, not
actual flags (by doing & ASYNC_SPD_MASK). So rename 'flags' to
'old_speed' (after what it is).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-66-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_set_serial_info already defined a local 'port' of type struct
tty_port. So use it in the code everywhere.
This eliminates some text from the code there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-65-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
info->MCR is protected by info->slock all over the code. Extend the lock
in mxser_tiocmget around the info->MCR fetch too.
It likely doesn't change anything, but it's always good to be consistent.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-64-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix spelling of "enhanced" in macros and comments around them.
While "enchance" comes from the original Moxa's driver, I don't think it
was meant to be that. From the context, they obviously mean "enhanced".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-63-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, some of the values written to FCR are magic constants. But
they are composed of well-defined bits. Use these named macros in place
of the constants.
No changes in objdump -d.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-62-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_port::xmit_cnt is unsigned, it cannot be negative. Therefore
remove all the xmit_cnt < 0 tests.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-61-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting and stopping TX is performed on many places in the driver. It
is repeated outb and info->IER modification. Create few helpers
(__mxser_start_tx, mxser_start_tx, __mxser_stop_tx) and use them in the
code instead of open coding.
This should be a base for an uart driver for this device in the future.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-60-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CTS is handled on two locations in mxser. Extract the code into
separation function mxser_handle_cts. And call it from the two
locations.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-59-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX is not supposed to be started from tty_operations::put_char. Line
disciplines ought to call tty_operations::put_char several times and
then do a single tty_operations::flush_chars to start TX.
Fix this in mxser by removing TX startup from mxser_put_char.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-58-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_dtr_rts now does all inb, outb, & or | in a single statement. The
code is hard to follow, so make it more readable by doing one-line =
one-statement.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-57-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_rs_break now does all inb, outb, & or | in a single statement. The
code is hard to follow, so make it more readable by doing one-line =
one-statement.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-56-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct mxser_port::ioaddr can never be NULL once set in ->probe. Hence
the checks for it are pointless. Remove them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-55-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many boards have only 2 ports. But we always allocate 8 ports (struct
mxser_port) in each struct mxser_board.
Switch this to an empty/variable sized array ([]) and allocate the
needed number of ports using struct_size helper in ->probe.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-54-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to preallocate an array of four struct mxser_board's.
In most cases a single board or two will be present in a machine. So
allocate struct mxser_board as needed in ->probe.
This makes mxser_boards a bit array. There we store which indexes are
free (unallocated).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-53-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_board::idx is named as index, but actually contain a base. So
assign index there. And for base, introduce a local variable.
This is needed for the next patch (use index as a bit index).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-52-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mxser_open, tty->port is already set thanks to
tty_port_register_device in ->probe. So we can simply use container_of
to deduce the struct mxser_port's pointer. Thus avoiding divisions and
complex computations.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-51-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename process_txrx_fifo to mxser_process_txrx_fifo and:
* remove useless parentheses
* return from the 'if's true branch and process the rest in normal code
flow (shift the code one level left)
All this to make the code more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-50-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that mxser_cards array (of struct mxser_cardinfo) contains only port
count and a quirk, we can encode these two directly into
pci_device_id::driver_data. And we can remove this struct completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-49-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a dev_info in ->probe which prints device's name, bus and slot
numbers. All these can be fetched from the lspci output. So remove this
useless print.
This eliminates the whole mxser_cardinfo::name field.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-48-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move request_irq from mxser_initbrd to mxser_probe so that we can switch
it to managed request. It simplifies the cleanup code.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-47-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to managed resources for PCI using pcim_enable_device.
Regions and device disabling is now taken care of by the core and we
need not unwind. Neither in ->probe, nor in ->remove. That simplifies
the code.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-46-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only user of mxser_board_remove is mxser_remove. Move there those
few lines.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-45-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
What's done in ->probe for board is actually its initialization. So move
it to mxser_initbrd where it belongs.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-44-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the rest of MUST helpers. They all can use the newly added
mxser_must_set_EFR. And passing a bool instead of having two functions
(_enable+_disable) simplifies the code a lot too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-43-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Again, selecting a bank in the EFR register is duplicated many times.
Extract it to a separate function (mxser_must_select_bank) and use it on
all the places.
This cleans up most of the helpers. And mxser_get_must_hardware_id now
returns the HW ID directly, not via a by-reference parameter.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-42-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple copies of setting the EFR register. Separate it to a
new universal function called __mxser_must_set_EFR. And use it in the
code by introducing mxser_must_set_enhance_mode instead of
mxser_disable_must_enchance_mode and mxser_enable_must_enchance_mode.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-41-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ModeMask local array is just inverted OP_MODE_MASK shifted by shiftbit.
Drop this array and use the value directly.
* return from the if's true branch and drop 'else' branch by moving the
code completely outside the if.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-40-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This ioctl code sets RS232, RS422 or RS485 mode. Move the code to a
separate function (mxser_ioctl_op_mode) with a note that these
mxser-special ioctls should be likely replaced eventually by TIOCGRS485
and TIOCSRS485.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-39-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's an once-set constant, so define a macro for the constant
(MXSER_CUSTOM_DIVISOR) and use it in the code instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-37-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's an once-set constant, so define a macro for the constant
(MXSER_BAUD_BASE) and use it in the code instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-36-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's been a long time since mxser_port::stop_rx was abandoned. Remove it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-35-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patches, mxser_port::normal_termios is unused, so
time to wave bye-bye.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-34-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MXSER_PORTS's tty_device is never registered and neither its
tty_port instance exists. Hence, it's quite pointless to allocate it.
It used to be used for global information fetches via ioctls. We have
just removed these as non-existent tty_device+tty_port was exactly the
reason to remove the ioctls.
It would be peculiar to add this "virtual" port as we require a backing
tty_port since commit ecbbfd44a0 (TTY: move tty buffers to tty_port)
in 2012.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-33-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous ioctls removal, cnt is needed only in
mxser_receive_chars_old now. So remove it from mxser_receive_chars and
mxser_receive_chars_new and account only in mxser_receive_chars_old.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-32-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The semantics are defined exactly nowhere.
2) The ioctl definition was never exposed to userspace, so noone should
actually be reliably using this.
3) It's not even mentioned in any of the mxser utilities.
Provided the above, remove this mxser-special ioctl.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-31-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The semantics are defined exactly nowhere.
2) The ioctl definition was never exposed to userspace, so noone should
actually be reliably using this.
3) It's not even mentioned in any of the mxser utilities.
Provided the above, remove this mxser-special ioctl.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-30-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) MOXA_GETMSTATUS is broken at least since commit ecbbfd44a0 (TTY:
move tty buffers to tty_port) in 2012.
Even though it's mentioned in the mon_pa moxa utility, obviously
noone ever tried that in that timeframe.
2) The ioctl definition was never exposed to userspace, so noone
should actually be reliably using this.
Provided the above, remove this mxser-special ioctl.
And remove the whole concept of mxser_ioctl_special as this was the last
ioctl in there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-29-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) MOXA_GETDATACOUNT is broken at least since commit ecbbfd44a0 (TTY:
move tty buffers to tty_port) in 2012.
Even though it's mentioned in the mon_p moxa utility, obviously noone
ever tried that in that timeframe.
2) The ioctl definition was never exposed to userspace, so noone should
actually be reliably using this.
Provided the above, remove this mxser-special ioctl.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-28-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) MOXA_CHKPORTENABLE is broken at least since commit ecbbfd44a0 (TTY:
move tty buffers to tty_port) in 2012.
2) The ioctl definition was never exposed to userspace, so noone should
actually be reliably using this.
3) It's not even mentioned in any of the mxser utilities.
Provided the above, remove this mxser-special ioctl.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The semantics are defined exactly nowhere.
2) The ioctl definition was never exposed to userspace, so noone should
actually be reliably using this.
3) It's not even mentioned in any of the mxser utilities.
Provided the above, remove this mxser-special ioctl.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-26-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) MOXA_ASPP_MON_EXT is broken at least since commit ecbbfd44a0 (TTY:
move tty buffers to tty_port) in 2012.
2) The ioctl definitions were never exposed to userspace, so noone should
actually be reliably using them.
3) They're not even mentioned in any of the mxser utilities.
So remove all these mxser-special ioctls: MOXA_ASPP_MON,
MOXA_ASPP_MON_EXT, and MOXA_SDS_RSTICOUNTER.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-25-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The semantics are defined exactly nowhere.
2) The ioctl definition was never exposed to userspace, so noone should
actually be reliably using this.
3) It's not even mentioned in any of the mxser utilities.
Provided the above, remove this mxser-special ioctl.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-24-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* UART_MCR_AFE is a redefinition of serial_reg.h's one.
* UART_LSR_SPECIAL is a redefinition of serial_reg.h's
UART_LSR_BRK_ERROR_BITS.
So remove both and replace the latter uses by already defined
UART_LSR_BRK_ERROR_BITS.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-21-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the xmit ring buffer pointers and counter (xmit_head, xmit_tail,
xmit_cnt) unsigned. Now, the assumptions for the compiler are clear --
they cannot be negative.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-20-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In struct mxser_port, all the UART registers and masks, and the xon/xoff
character are stored into int. Let's re-type all these as UART registers
are 8bit (u8) and xon/xoff character is an unsigned char (cc_t in
ktermios).
This save some bytes in memory, but more importantly the change makes it
what it really is.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-19-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART_LSR_SPECIAL is composed of UART_LSR_BI, UART_LSR_PE, UART_LSR_FE,
UART_LSR_OE. So status cannot be anything else. Remove the unused else
branch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-18-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maciej W. Rozycki
Juergen Gross
Andy Shevchenko
Johan Hovold
Jon Hunter
Jiri Slaby
Colin Ian King
Shubhrajyoti Datta
Igor Matheus Andrade Torrente
Tamseel Shams
Bing Fan
Lino Sanfilippo
Zheyu Ma
Jianmin Lv
Uwe Kleine-König
Linus Torvalds
Pali Rohár
Jinchao Wang
Vignesh Raghavendra
Dmitry Baryshkov
Greg Kroah-Hartman
Julian Wiedmann
Jason Li