Make the max14577 charger driver depending on SYSFS instead selecting
it. This fixes warning on x86_64 with allmodconfig:
scripts/kconfig/conf --allmodconfig Kconfig
fs/sysfs/Kconfig:1:error: recursive dependency detected!
fs/sysfs/Kconfig:1: symbol SYSFS is selected by CHARGER_MAX14577
drivers/power/Kconfig:327: symbol CHARGER_MAX14577 depends on POWER_SUPPLY
drivers/power/Kconfig:1: symbol POWER_SUPPLY is selected by HID_SONY
drivers/hid/Kconfig:638: symbol HID_SONY depends on NEW_LEDS
drivers/leds/Kconfig:8: symbol NEW_LEDS is selected by SENSORS_APPLESMC
drivers/hwmon/Kconfig:299: symbol SENSORS_APPLESMC depends on HWMON
drivers/hwmon/Kconfig:5: symbol HWMON is selected by EEEPC_LAPTOP
drivers/platform/x86/Kconfig:496: symbol EEEPC_LAPTOP depends on HOTPLUG_PCI
drivers/pci/hotplug/Kconfig:5: symbol HOTPLUG_PCI depends on SYSFS
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove hard-coded values for:
- Fast Charge current,
- End Of Charge current,
- Fast Charge timer,
- Overvoltage Protection Threshold,
- Battery Constant Voltage,
and use DTS or sysfs to configure them. This allows using the max14577 charger
driver with different batteries.
Now the charger driver requires valid configuration data from DTS. In
case of wrong configuration data it fails during probe.
The fast charge timer is configured through sysfs entry.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 charger to the max14577 driver. The MAX77836
charger is almost the same as 14577 model except:
- No dead-battery detection;
- Support for special charger (like in MAX77693);
- Support for DX over-voltage protection (like in MAX77693);
- Lower values of charging current (two times lower current for
slow/fast charge, much lower EOC current);
- Slightly different values in ChgTyp field of STATUS2 register. On
MAX14577 0x6 is reserved and 0x7 dead battery. On the MAX77836 the
0x6 means special charger and 0x7 is reserved. Regardless of these
differences the driver maps them to one enum max14577_muic_charger_type.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds a driver for reading the battery status of the
battery connected to the Atmel microcontroller on the
iPAQ h3xxx series.
Based on a driver from handhelds.org 2.6.21 kernel, written
by Alessandro GARDICH.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `goldfish_battery_probe':
drivers/power/goldfish_battery.c:181: undefined reference to `devm_ioremap'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX14577 chip is a multi-function device which includes MUIC, charger and
voltage regulator. The driver is located in drivers/mfd.
This patch supports battery charging control of MAX14577 chip and provides
power supply class information to userspace.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
max17042 now uses regmap interface but does not enable config option. This
patch fixes the following build errors:
drivers/power/max17042_battery.c:661:15: error: variable ‘max17042_regmap_config’ has initializer but incomplete type
drivers/power/max17042_battery.c:662:2: error: unknown field ‘reg_bits’ specified in initializer
drivers/power/max17042_battery.c:662:2: warning: excess elements in struct initializer
drivers/power/max17042_battery.c:662:2: warning: (near initialization for ‘max17042_regmap_config’)
drivers/power/max17042_battery.c:663:2: error: unknown field ‘val_bits’ specified in initializer
drivers/power/max17042_battery.c:663:2: warning: excess elements in struct initializer
drivers/power/max17042_battery.c:663:2: warning: (near initialization for ‘max17042_regmap_config’)
drivers/power/max17042_battery.c:664:2: error: unknown field ‘val_format_endian’ specified in initializer
drivers/power/max17042_battery.c:664:23: error: ‘REGMAP_ENDIAN_NATIVE’ undeclared here (not in a function)
drivers/power/max17042_battery.c:664:2: warning: excess elements in struct initializer
drivers/power/max17042_battery.c:664:2: warning: (near initialization for ‘max17042_regmap_config’)
drivers/power/max17042_battery.c: In function ‘max17042_probe’:
drivers/power/max17042_battery.c:684:2: error: implicit declaration of function ‘devm_regmap_init_i2c’
Signed-off-by: Austin Boyle <boyle.austin@gmail.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Adds support for the bq24735 charger chipset. The bq24735 is a
high-efficiency, synchronous battery charger.
It allows control of the charging current, input current, and the charger
voltage DAC's through SMBus.
Signed-off-by: Darbha Sriharsha <dsriharsha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Thanks-to: Stephen Warren <swarren@wwwdotorg.org>
Thanks-to: Thierry Reding <thierry.reding@gmail.com>
Thanks-to: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This driver is used and tested on gta04 phone. It's using twl4030_madc
(similar to rx51 existing driver). Driver also implement charging and
discharging calibration data so user can define ranges and level.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Lukas Märdian <lukas@goldelico.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add driver support for the Texas Instruments BQ24190 battery charger.
Some of the information provided by the device is about the charger and
other information is about the battery so create two power_supply objects
(one for each) and provide the appropriate information for each one.
The device has many fields that go beyond what is reasonable to report or
modify using the existing 'POWER_SUPPLY_PROP_*' properties so the driver
exports the register fields via sysfs. They are prefixed by 'f_' (for
'field') to make it easier to distinguish between a register field and a
"normal" sysfs file exported by the power_supply infrastructure.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Nearly all the other goldfish peripherals (mtd, keyboard, etc) have a
dependency on the main platform's GOLDFISH Kconfig item, but this one got
skipped. Even with consistency as a justification, there was initial
resistance[1] from some people to adding it however, as they wanted the
extra compile coverage.
Now, with CONFIG_COMPILE_TEST, we have the middle ground that will give
people the coverage who want it, and let those who don't want it to skip
ever seeing the option presented.
[1] https://lkml.org/lkml/2013/2/27/333
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch fixes build failure(randconfig) of next-20130501. When config
I2C as m, BATTERY_BQ27x00 as y, here comes the failure. The driver depends
on I2C only if I2C is not disabled, as Lars commented. Last version of
this patch make the driver depend on I2C unconditionally.
Failure message:
drivers/built-in.o: In function `bq27x00_read_i2c':
bq27x00_battery.c:(.text+0x1082a7): undefined reference to `i2c_transfer'
drivers/built-in.o: In function `bq27x00_battery_init':
bq27x00_battery.c:(.init.text+0x6085): undefined reference to `i2c_register_driver'
bq27x00_battery.c:(.init.text+0x60c7): undefined reference to `i2c_del_driver'
drivers/built-in.o: In function `bq27x00_battery_exit':
bq27x00_battery.c:(.exit.text+0xbf0): undefined reference to `i2c_del_driver'
make: *** [vmlinux] Error 1
Signed-off-by: Xiong Zhou <jencce.kernel@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Fix build errors in lp8788-charger by making it depend on IIO.
Fixes errors when CONFIG_IIO=m and CHARGER_LP8788=y.
lp8788-charger.c:(.text+0x2146b5): undefined reference to `iio_channel_get'
lp8788-charger.c:(.text+0x2146ce): undefined reference to `iio_channel_get'
lp8788-charger.c:(.text+0x214a86): undefined reference to `iio_read_channel_processed'
lp8788-charger.c:(.text+0x214b51): undefined reference to `iio_read_channel_processed'
lp8788-charger.c:(.text+0x214c30): undefined reference to `iio_read_channel_processed'
lp8788-charger.c:(.text+0x214d93): undefined reference to `iio_channel_release'
lp8788-charger.c:(.text+0x214dac): undefined reference to `iio_channel_release'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
- OpenFirmware/DeviceTree support for the Power Supply core: the core now
automatically populates supplied_from hierarchy from the device tree.
With these patches chargers and batteries can now lookup each other
without the board files support shim. Rhyland Klein at NVIDIA did the
work;
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using the
AB85xx core and depends on some recent changes to it, so that is why the
driver comes through the battery tree. It has an appropriate ack from
the hwmon maintainer (i.e. Guenter Roeck). Martin Persson at ST-Ericsson
and Hongbo Zhang at Linaro authored the driver;
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The changes
touch mfd parts, but these were acked by the appropriate MFD maintainer
(i.e. Samuel Ortiz). Lee Jones at Linaro did most of the work and lead
the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones;
- Versatile Express poweroff driver moved into drivers/power/reset/.
- Tree-wise: use devm_kzalloc() where appropriate;
- Tree-wise: dev_pm_ops cleanups/fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=5BdE
-----END PGP SIGNATURE-----
Merge tag 'for-v3.10' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- OpenFirmware/DeviceTree support for the Power Supply core: the core
now automatically populates supplied_from hierarchy from the device
tree. With these patches chargers and batteries can now lookup
each other without the board files support shim. Rhyland Klein at
NVIDIA did the work
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using
the AB85xx core and depends on some recent changes to it, so that
is why the driver comes through the battery tree. It has an
appropriate ack from the hwmon maintainer (i.e. Guenter Roeck).
Martin Persson at ST-Ericsson and Hongbo Zhang at Linaro authored
the driver
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The
changes touch mfd parts, but these were acked by the appropriate
MFD maintainer (ie Samuel Ortiz). Lee Jones at Linaro did most of
the work and lead the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones
- Versatile Express poweroff driver moved into drivers/power/reset/
- Tree-wide: use devm_kzalloc() where appropriate
- Tree-wide: dev_pm_ops cleanups/fixes"
* tag 'for-v3.10' of git://git.infradead.org/battery-2.6: (112 commits)
pm2301-charger: Fix suspend/resume
charger-manager: Use kmemdup instead of kzalloc + memcpy
power_supply: Populate supplied_from hierarchy from the device tree
power_supply: Add core support for supplied_from
power_supply: Define Binding for power-supplies
rx51_battery: Fix reporting temperature
hwmon: Add ST-Ericsson ABX500 hwmon driver
ab8500_bmdata: Export abx500_res_to_temp tables for hwmon
ab8500_{bmdata,fg}: Add const attributes to some data arrays
ab8500_bmdata: Eliminate CamelCase warning of some variables
ab8500_btemp: Make ab8500_btemp_get* interfaces public
goldfish_battery: Use resource_size()
lp8788-charger: Use PAGE_SIZE for the sysfs read operation
max8925_power: Use devm_kzalloc()
da9030_battery: Use devm_kzalloc()
da9052-battery: Use devm_kzalloc()
ds2760_battery: Use devm_kzalloc()
ds2780_battery: Use devm_kzalloc()
gpio-charger: Use devm_kzalloc()
isp1704_charger: Use devm_kzalloc()
...
This patch adds support for the tps65090 charger driver. This driver is
responsible for controlling the charger aspect of the tps65090 mfd.
Currently, this mainly consists of turning on and off the charger, but
some features of the charger can be supported through this driver
including:
- Enable Auto Recharge based on Battery voltage
- Fast Charge Safety Timer
- Maximum battery discharge current
- Maximum battery adapter current
- Enable External Charge
- Disable charging termination based on low charger current (supported)
Once the driver is accepted, later patches can add support for the
features above which are not yet supported.
Based on work by:
Syed Rafiuddin <srafiuddin@nvidia.com>
Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
there are no more users of CONFIG_USB_OTG_UTILS
left in tree, we can remove it just fine.
[ kishon@ti.com : fixed a linking error due
to original patch forgetting to change
drivers/usb/Makefile ]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The PM2301 Charger should always be available when using the AB8500
Battery Management system, we're ensuring this will be the case.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
Fix this link error on s390:
ERROR: "devm_request_threaded_irq" [drivers/power/goldfish_battery.ko] undefined!
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Pull a huge ab8500/pm2301 pile of changes from Lee Jones. Lee did an
awesome job cleaning this stuff up and thus brought ab8500 Stericsson's
development tree much closer to the mainline. Even more changes to come,
though.
Conflicts:
drivers/power/Kconfig
Add the emulated power driver for the Goldfish platform.
This folds together the code from the Google tree, Jun Nakajima's cleanups
and x86 porting work, and then a tidy up to pass checkpatch.
Signed-off-by: Mike A. Chan <mikechan@google.com>
[cleanup and x86 support]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Xiaohui Xin <xiaohui.xin@intel.com>
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Bruce Beare <bruce.j.beare@intel.com>
[ported to 3.4]
Signed-off-by: Tom Keel <thomas.keel@intel.com>
[ported to 3.7 and final tidy]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
AC charger driver for the DB9540 based platforms.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace the
proprietary Nokia BME stack;
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks to
Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers;
- Random fixups and enhancements for a bunch of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Bb5O
-----END PGP SIGNATURE-----
Merge tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6
Pull battery subsystem updates from Anton Vorontsov:
"Highlights:
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace
the proprietary Nokia BME stack
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks
to Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers
- Random fixups and enhancements for a bunch of drivers."
* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
max8925_power: Add support for device-tree initialization
ab8500: Add devicetree support for chargalg
ab8500: Add devicetree support for charger
ab8500: Add devicetree support for btemp
ab8500: Add devicetree support for fuelgauge
twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
jz4740-battery: Use devm_request_and_ioremap
jz4740-battery: Use devm_kzalloc
bq27x00_battery: Fixup nominal available capacity reporting
bq2415x_charger: Fix style issues
bq2415x_charger: Add Kconfig/Makefile entries
power_supply: Add bq2415x charger driver
power_supply: Add new Nokia RX-51 (N900) power supply battery driver
max17042_battery: Fix missing verify_model_lock() return value check
ds2782_battery: Fix signedness bug in ds278x_read_reg16()
lp8788-charger: Fix ADC channel names
lp8788-charger: Fix wrong ADC conversion
lp8788-charger: Use consumer device name on setting IIO channels
power_supply: Register power supply for thermal cooling device
power_supply: Add support for CHARGE_CONTROL_* attributes
...
Given appropriate devicetree bindings, this driver registers a
pm_power_off function to set a GPIO line high/low to power down
your board.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by:Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds device tree support for battery-temperature-monitor driver
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This driver exporting battery design capacity, temperature and voltage for
battery in Nokia RX-51. This driver is needed for open source battery
management on Nokia RX-51 (N900).
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
- Marvell 88pm860x charger and battery drivers;
- Texas Instruments LP8788 charger driver;
2. Two new power supply properties: whether a battery is authentic, and
chargers' maximal currents and voltages;
3. A lot of TI LP8727 Charger cleanups;
4. New features for Charger Manager, mainly now we can disable specific
regulators;
5. Random fixes and cleanups for other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=LkdH
-----END PGP SIGNATURE-----
Merge tag 'for-v3.7' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"1. New drivers:
- Marvell 88pm860x charger and battery drivers;
- Texas Instruments LP8788 charger driver;
2. Two new power supply properties: whether a battery is authentic,
and chargers' maximal currents and voltages;
3. A lot of TI LP8727 Charger cleanups;
4. New features for Charger Manager, mainly now we can disable
specific regulators;
5. Random fixes and cleanups for other drivers."
Fix up trivial conflicts in <linux/mfd/88pm860x.h>
* tag 'for-v3.7' of git://git.infradead.org/battery-2.6: (52 commits)
pda_power: Remove ac_draw_failed goto and label
charger-manager: Add support sysfs entry for charger
charger-manager: Support limit of maximum possible
charger-manager: Check fully charged state of battery periodically
lp8727_charger: More pure cosmetic improvements
lp8727_charger: Fix checkpatch warning
lp8727_charger: Add description in the private data
lp8727_charger: Fix a typo - chg_parm to chg_param
lp8727_charger: Make some cosmetic changes in lp8727_delayed_func()
lp8727_charger: Clean up lp8727_charger_changed()
lp8727_charger: Return if the battery is discharging
lp8727_charger: Make lp8727_charger_get_propery() simpler
lp8727_charger: Make lp8727_ctrl_switch() inline
lp8727_charger: Make lp8727_init_device() shorter
lp8727_charger: Clean up lp8727_is_charger_attached()
lp8727_charger: Use specific definition
lp8727_charger: Clean up lp8727 definitions
lp8727_charger: Use the definition rather than enum
lp8727_charger: Fix code for getting battery temp
lp8727_charger: Clear interrrupts at inital time
...
Driver to allow use of the ADC drivers supported by the IIO
subsystem for battery status monitoring. Connecting this
driver to the relevant IIO device requires registration of
the appropriate iio_map structure array by the IIO device
driver (usually from platform data). If specified the driver
will also make use of a gpio to provide interrupt driven
notification that the battery is fully charged.
In last version:
Addressed concerns raised by lars:
a. made the adc_bat per device.
b. get the IIO channel using hardcoded channel names.
c. Minor issues related to gpio_is_valid and some code
refactoring.
In V1:
Addressed concerns raised by Anton:
a. changed the struct name to gab(generic adc battery).
b. Added some functions to neaten the code.
c. Some minor coding guidelines changes.
d. Used the latest function introduce by lars:
iio_read_channel_processed to streamline the code.
In V2:
Addressed concerns by lars:
a. No need of allocating memory for channels.Make it array.
b. Code restructring, coding style and following kernel guidelines changes
suggested by him.
In V3:
Addressed conerns by Anton:
a. Added the copyright.
b. Coding guidelines changes suggested by him.
c. Added Makefile and Kconfig
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are charger and battery measurement feature for 88pm860x PMIC.
For charger, it can support pre-charge with small current when battery is
nearly exausted and then changed into fast-charge with CC&CV mode.
For battery monitor, it can support battery measurement such as
vbat,vsys,vchg and ibat etc,it can aslo accumulating the Coulomb value
charged or discharged from battery based on Conlomb Counter, we use it
to estimate battery capacity.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight
driver and current sinks.
This patch supports the charger operations including the charger
interrupt handling.
The LP8788 charger driver provides configurable platform data. The
charger platform data includes ADC input ID, maximum battery voltage,
charging parameters and etc.
The ADC input is used for getting the battery voltage and temperature.
Charging parameters are used for updating the charger operations such
like setting charging current and setting End-of-charge conditions.
When the charging interrupt occurs, power supply uevents are generated
in order to update the user-space information. For platform specific
charger action, the charger_event() function can be used in the
platform side.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The fix for MFD part is already merged so we can remove the broken mark
for da9052-battery.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that is)
caught the issue and it was decided[1] that I'd just delay the battery
pull request, and then will fix it up by merging upstream back into
battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem was
needed to get rid of a warning in power supply subsystem (the warning
was not drivers/power's "fault", the thermal registration function just
needed a proper const annotation, which is also done by a small commit
on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=1NaS
-----END PGP SIGNATURE-----
Merge tag 'for-v3.6' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"The tag contains just a few battery-related changes for v3.6. It's is
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that
is) caught the issue and it was decided[1] that I'd just delay the
battery pull request, and then will fix it up by merging upstream back
into battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem
was needed to get rid of a warning in power supply subsystem (the
warning was not drivers/power's "fault", the thermal registration
function just needed a proper const annotation, which is also done by
a small commit on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28"
* tag 'for-v3.6' of git://git.infradead.org/battery-2.6: (23 commits)
thermal: Constify 'type' argument for the registration routine
olpc-battery: update CHARGE_FULL_DESIGN property for BYD LiFe batteries
olpc-battery: Add VOLTAGE_MAX_DESIGN property
charger-manager: Fix build break related to EXTCON
lp8727_charger: Move header file into platform_data directory
power_supply: Add min/max alert properties for CAPACITY, TEMP, TEMP_AMBIENT
bq27x00_battery: Add support for BQ27425 chip
charger-manager: Set current limit of regulator for over current protection
charger-manager: Use EXTCON Subsystem to detect charger cables for charging
test_power: Add VOLTAGE_NOW and BATTERY_TEMP properties
test_power: Add support for USB AC source
gpio-charger: Use cansleep version of gpio_set_value
bq27x00_battery: Add support for power average and health properties
sbs-battery: Don't trigger false supply_changed event
twl4030_charger: Allow charger to control the regulator that feeds it
twl4030_charger: Add backup-battery charging
twl4030_charger: Fix some typos
max17042_battery: Support CHARGE_COUNTER power supply attribute
smb347-charger: Add constant charge and current properties
power_supply: Add constant charge_current and charge_voltage properties
...
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
This patch select CONFIG_EXTCON to resolve below build break of
charger-manager because charger-manager use API of EXTCON subsystem.
drivers/built-in.o: In function `charger_manager_probe':
charger-manager.c:(.text+0x11d61a): undefined reference to `extcon_register_interest'
charger-manager.c:(.text+0x11d7b6): undefined reference to `extcon_unregister_interest'
drivers/built-in.o: In function `charger_manager_remove':
charger-manager.c:(.devexit.text+0x8f3): undefined reference to `extcon_unregister_interest'
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
After a clean-up of the interfaces the OMAP Smartreflex IP driver is now a
generic driver. Move it to drivers/power/avs/.
The build is controlled by the following Kconfig options:
. CONFIG_POWER_AVS: general knob for Adaptive Voltage Scaling support,
. CONFIG_POWER_AVS_OMAP: AVS(Adaptive Voltage Scaling)
support on OMAP containing the version 1 or version 2 of the SmartReflex IP,
. CONFIG_POWER_AVS_OMAP_CLASS3: Class 3 implementation of Smartreflex.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
max17047 is improved version of max17042 chip. It has few HW bug
fixes with minor changes in register set.
max17050 is same as max17047 chip except its silicon packging. So from
driver's point of view there is no difference btw max1047 and max1050.
This patch adds the support to dynamically detect the chip type and
adds steps to initialize the max17047 chip.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
The smb347-charger driver does a lot of read-modify-write to the device
registers. Instead of open-coding everything we can take advantage of
regmap API which provides nice functions to do this kind of things.
In addition there is no need for custom debugfs file for dumping
registers as this is already provided by the regmap API.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
On Mon, Apr 02, 2012 at 01:53:23PM +1000, Benjamin Herrenschmidt wrote:
> > drivers/built-in.o: In function `.nouveau_pm_trigger':
> > (.text+0xa56e8): undefined reference to `.power_supply_is_system_supplied'
> >
> > nouveau probably needs to depends on CONFIG_POWER_SUPPLY to force a module
> > build with the latter is =m
>
> Ok, not that trivial...
>
> The problem is more like POWER_SUPPLY should be a bool, not a tristate.
>
> If you think about it: you don't want things like nouveau to depend on a
> random subsystem like that, people will never get it. In fact,
> POWER_SUPPLY provides empty inline stubs when not enabled, so that's
> really designed to not have depends...
>
> However that -cannot- work if POWER_SUPPLY is modular and the drivers
> who use it are not.
>
> The only fixes here that make sense I can think of
> that don't also involve Kconfig horrors are:
>
> - Ugly: in power_supply.h, use the extern variant if
>
> defined(CONFIG_POWER_SUPPLY) ||
> (defined(CONFIG_POWER_SUPPLY_MODULE) && defined(MODULE))
>
> IE. use the stub if power supply is a module and what is being built is
> built-in. Of course that's not only ugly, it somewhat sucks from a user
> perspective as the subsystem now exists but can't be used by some
> drivers...
>
> - Better: Just make the bloody thing a bool :-) The power supply
> framework itself is small enough, just make it a boolean option and
> avoid the problem entirely. The actual power supply sub drivers can
> remain modular of course.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
- A quite complex ab8500 charger driver, submitted by
Arun Murthy @ ST-Ericsson;
- Summit Microelectronics SMB347 Battery Charger, submitted by
Bruce E. Robertson and Alan Cox @ Intel.
And that's all.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=Y8fe
-----END PGP SIGNATURE-----
Merge tag 'for-v3.4-rc1' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Various small bugfixes and enhancements, plus two new drivers:
- A quite complex ab8500 charger driver, submitted by Arun Murthy @
ST-Ericsson;
- Summit Microelectronics SMB347 Battery Charger, submitted by Bruce
E Robertson and Alan Cox @ Intel.
And that's all."
* tag 'for-v3.4-rc1' of git://git.infradead.org/battery-2.6: (36 commits)
max17042_battery: Clean up interrupt handling
Revert "max8998_charger: Include linux/module.h just once"
ab8500_fg: Fix some build warnings on x86_64
max17042_battery: Fix CHARGE_FULL representation.
max8998_charger: Include linux/module.h just once
power_supply: Convert i2c drivers to module_i2c_driver
lp8727_charger: Add MODULE_DEVICE_TABLE
charger-manager: Simplify charger_get_property(), get rid of a warning
charger-manager: Clean up for better readability
da9052-battery: Convert to use module_platform_driver
da9052-battery: Fix a memory leak when unload the module
da9052-battery: Add missing platform_set_drvdata
ab8500: Turn unneeded global symbols into local ones
ab8500_fg: Fix copy-paste error
ab8500_fg: Get rid of 'struct battery_type'
ab8500_fg: Get rid of 'struct v_to_cap'
ab8500_btemp: Get rid of 'enum adc_therm'
ab8500_charger: Convert to the new USB OTG calls
ab8500-btemp: AB8500 battery temperature driver
ab8500-fg: A8500 fuel gauge driver
...
This driver is responsible for battery detection, obtaining battery
temperature and monitor the battery temperature by taking precautionary
measurements when battery temperature goes beyond or below the thresholds.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Driver support for the Summit I²C battery charger. This is used in some
Intel devices.
Signed-off-by: Bruce E. Robertson <bruce.e.robertson@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Add 'Texas Instruments' because TI acquired National semiconductor at 2011.
And the driver information is added in the header file.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
There are some problems with MFD part of this driver, so the
driver fails to build:
drivers/power/da9052-battery.c: In function 'da9052_bat_read_volt':
drivers/power/da9052-battery.c:293:2: error: implicit declaration of function 'da9052_adc_manual_read' [-Werror=implicit-function-declaration]
drivers/power/da9052-battery.c: In function 'da9052_bat_check_presence':
drivers/power/da9052-battery.c:306:2: error: implicit declaration of function 'da9052_adc_read_temp' [-Werror=implicit-function-declaration]
drivers/power/da9052-battery.c: In function 'da9052_determine_vc_tbl_index':
drivers/power/da9052-battery.c:348:1: warning: control reaches end of non-void function [-Wreturn-type]
cc1: some warnings being treated as errors
The fix for MFD part will probably go post -rc1 (or in the next merge
window), so let's disable the driver for now.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Krzysztof Kozlowski
Dmitry Artamonow
Linus Torvalds
Richard Weinberger
Austin Boyle
Darbha Sriharsha
Martin Schwidefsky
Marek Belisko
Mark A. Greer
Paul Gortmaker
Xiong Zhou
Randy Dunlap
Rhyland Klein
Felipe Balbi
Marcus Cooper
Heiko Carstens
Anton Vorontsov
Mike Lockwood
Michel JAOUEN
Jamie Lentin
Rajanikanth H.V
Anton Vorontsov
Pali Rohár
anish kumar
Jett.Zhou
Kim, Milo
Axel Lin
Chanwoo Choi
Paul Bolle
Tony Lindgren
Jean Pihet
Ramakrishna Pallala
Mika Westerberg
Arun Murthy
Bruce E. Robertson
Renata Sayakhova