This patch adds support for 405GPr processors with optional
new mode strapping. ibm405gp_fixup_clocks() can now be used
for 405GP and 405GPr CPUs.
This is in preparation of porting the cpci405 platform support
from arch/ppc to arch/powerpc.
This patch also adds ibm405ep_fixup_clocks() to support
405EP CPUs from the boot wrapper.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Enable EMAC driver for Sequoia (and while we're in there, disable
Macintosh drivers for Sequoia and Bamboo).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Somehow the EMAC support was dropped (or never really added) to the
Kilauea defconfig file. This patch finally adds EMAC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The logic that checks to see if a machine check is caused by an NMI will
always match when NMI hasn't been initialized, since the mpic routine
will return NO_IRQ (and that's what the nmi_virq value is as well).
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit aed3a8c9bb introduced a
definition of notify_spus_active in .../cell/spu_syscalls.c, and
another definition under #ifndef MODULE in .../cell/spufs/sched.c.
The latter is not necessary and causes the build to fail when
CONFIG_SPU_FS=y, so this removes it. It also removes the export
of do_notify_spus_active, which is unnecessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
This reverts commit 553aa7659b at Ben H's
request, because it confused IORESOURCE_* flags with command register
bits.
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable MSI now that we have an implementation, and enable CONFIG_MD and
the raid options by default as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
By default the OpenPIC on PWRficient will bias to one core (since that
will improve changes of the other core being able to stay idle/powered
down). However, this conflicts with most irq load balancing schemes,
since setting an interrupt to be delivered to either core doesn't really
result in the load being shared. It also doesn't work well with the
soft irq disable feature of PPC, since EE will stay on until the first
interrupt is taken while soft disabled.
Set the gconf0 config bit that enables even distribution of interrupts
among the two cores.
Signed-off-by: Olof Johansson <olof@lixom.net>
Some PWRficient-based boards have a NMI button that's wired up to a GPIO
as interrupt source. By configuring the openpic accordingly, these get
delivered as a machine check with high priority, instead of as an external
interrupt.
The device tree contains a property "nmi-source" in the openpic node
for these systems, and it's the (hwirq) source for the input.
Also, for these interrupts, the IACK is read from another register than
the regular (MCACK instead), but they are EOI'd as usual. So implement
said function for the mpic driver.
Finally, move a couple of external function defines to include/ instead
of local under sysdev. Being able to mask/unmask and eoi directly saves
us from setting up a dummy irq handler that will never be called.
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix a bug in the printing of the os-area magic numbers which assumed
that magic numbers were zero terminated strings. The magic numbers
are represented in memory as integers. If the os-area sections are
not initialized correctly they could contained random data that would
be printed to the display. Also unify the handling of header and db
magic numbers and make both of type array of u8.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes an OProfile dependency on the spufs module. This
dependency was causing a problem for multiplatform systems that are
built with support for Oprofile on Cell but try to load the oprofile
module on a non-Cell system.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some machine_xx_initcall macros were recently added that check for the machine
type before calling the function. This converts the 4xx platforms to use those
for bus probing.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Remove the declarations for isa_io_base and isa_mem_base as they are declared
in pci-common.c now.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The e200 and e500 platforms are separated in various parts of the kernel with
ifdefs, most notably reg_booke.h and traps.c. The new machine_check rework
requires them to be similarly separated in cputable.c to avoid compile errors.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Enable PCI support for these eval boards among other things. Also selects
PCI for Rainier in the Kconfig file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds basic support for the AMCC Makalu board to arch/powerpc.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Currently we have some limitations in the 4xx PCIe driver and can't
support all possible PCIe busses. But the current limits in the
dts file are quite low (only 16 busses per RC). This patch increases
the number to 64 per RC.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Renaming the CPU nodes with generic names put the CPU model in
the "model" property and thus broke the PowerPC 440EP(x)/440GR(x)
identical PVR workaround. The updates it to use the new model property
for CPU identification.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Recent DTC versions disallow certain special characters in full paths without
being quoted with {}. That however breaks compatibility with older DTC
versions. Work around this by renaming the CPU nodes for the 4xx files to a
generic node name, and specify the processor type in the model property of the
CPU node.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch sets the ibpre flag (Inbound Presence) for the 405EX
in the 4xx PCIe driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The recent changes from Benjamin Herrenschmidt to the ibm_newemac now
make it possible to support other 4xx variants by just defining the
correct properties in the device tree. In this case of the 405EX we
need to define "has-mdio" in the RGMII node and "has-inverted-stacr-oc"
and "has-new-stacr-staopc" in the EMAC node same as on the 440EPx.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
For EMAC support, 405EX needs to be defined to enable the corresponding
EMAC features (IBM_NEW_EMAC_EMAC4, etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A small error caused a header file to be removed making sequoia support no
longer compile. Fix it.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The mechanism to do the setup for 440A cores changed recently. This fixes
the 440grx setup function to call __fixup_440A_mcheck.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is a UIC cascade handler rework to use set_irq_chained_handler() for
cascade, just like othe ppc platforms do. With current implementation we have
additional redirection for irq handler and we call generic_handle_irq twice
(once for the primary uic and the other time for handling cascade interrupt).
This causes Ingo's realtime support patch to stop working on 4xx.
Not sure of any other possible problems though, but with
set_irq_chained_handler() we can abolish "struct irqaction cascade" from the
chip descriptor and call generic_handle_irq() once, directly for cascade irq.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch makes PowerPC 4xx UIC use generic level irq handler instead
of a custom handle_uic_irq() function. We ack only edge irqs in mask_ack
callback, since acking a level irq on UIC has no effect if the interrupt
is still asserted by the device, even if the interrupt is already masked.
So, to really de-assert the interrupt we need to de-assert the external
source first *and* ack it on UIC then. The handle_level_irq() function
masks and ack's the interrupt with mask_ack callback prior to calling
the actual ISR and unmasks it at the end. So, to use it with UIC interrupts
we need to ack level irqs in the unmask callback instead, after the ISR
has de-asserted the external interrupt source. Even if we ack the interrupt
that we didn't handle (unmask/ack it at the end of the handler, while
next irq is already pending) it will not de-assert the irq, untill we
de-assert its exteral source.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds runtime detection of the 440SPe revision A chips. These
chips are equipped with a slighly different PCIe core and need special/
different initialization. The compatible node is changed to
"plb-pciex-440spe" ("A" and "B" dropped). This is needed for boards that
can be equipped with both PPC revisions like the AMCC Yucca.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This makes 4xx embedded platforms re-assign all PCI resources as we
pretty much never care about what the various firmwares have done on
these, it's generally not compatible with the way the kernel will map
the bridges.
We still need to also enable bus renumbering on some of them, but I
will do that from a separate patch after I've fixed 4xx PCIe to handle
all bus numbers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This improves the way the 4xx PCI-E code handles checking for a link
and adds explicit testing of CRS result codes on config space accesses.
This should make it more reliable.
Also, bridges with no link are now still created, though config space
accesses beyond the root complex are filtered. This is one step toward
eventually supporting hotplug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This removes a bogus empty "ranges" property in the EBC device node
of the Bamboo board device-tree.
The "ranges" property should be created by the wrapper code when it is
implemented. Until then, remove the empty property since it incorrectly
implies that there is a 1:1 address mapping between the EBC and the OPB.
This also fixes a warning from newer DTCs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This reworks the boot wrapper library function that probes
the chip clocks. Better separate the base function that is
used on 440GX,SPe,EP,... from the uart fixups as those need
different device-tree path on different processors.
Also, rework the function itself based on the arch/ppc code
from Eugene Surovegin which I find more readable, and which
handles one more bypass case. Also handle the subtle difference
between 440EP/EPx and 440SPe/GX, on the former, PerClk is derived
from the PLB clock while on the later, it's derived from the OPB.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds macros to the boot wrapper to access the CPR
registers from the boot wrappers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 4xx bootwrapper occasionally needs to access SPR registers,
this adds mfspr/mtspr wrappers to it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a function to the bootwrapper 4xx library to decode memory
size on 440SPE processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the definition of the on-chip OHCI controller to the
Bamboo board's device-tree. This is enough to get it probed and
working, though a separate patch fixing a bug in the OHCI driver
is needed to make it reliable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the device-tree bits & call to ppc4xx_pci_find_bridges()
to make PCI work on the Bamboo board
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds base support for the AMCC Taishan 440GX evaluation
board.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device-tree bits for the
405GP based Walnut platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Brings EP405 support to arch/powerpc. The IRQ routing for the CPLD
comes from a device-tree property, PCI is working to the point where
I can see the video card, USB device, and south bridge.
This should work with both EP405 and EP405PC.
I've not totally figured out how IRQs are wired on this hardware
though, thus at this stage, expect only USB interrupts working,
pretty much the same as what arch/ppc did.
Also, the flash, nvram, rtc and temp control still have to be wired.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds some basic real mode based early udbg support for 40x
in order to debug things more easily
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device tree bits for
440GP based Ebony platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the previous 2 patches the support for the 4xx PCI Express
cells as found in the 440SPe revA, revB and 405EX.
Unfortunately, due to significant differences between these, and other
interesting "features" of those pieces of HW, the code isn't as simple
as it is for PCI and PCI-X and some of the functions differ significantly
between the 3 implementations. Thus, not only this code can only support
those 3 implementations for now and will refuse to operate on any other,
but there are added ifdef's to avoid the bloat of building a fairly large
amount of code on platforms that don't need it.
Also, this code currently only supports fully initializing root complex
nodes, not endpoint. Some more code will have to be lifted from the
arch/ppc implementation to add the endpoint support, though it's mostly
differences in memory mapping, and the question on how to represent
endpoint mode PCI in the device-tree is thus open.
Many thanks to Stefan Roese for testing & fixing up the 405EX bits !
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the previous patch the support for the 4xx PCI 2.x
bridges.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support code for the 4xx PCI-X bridge. It also provides
placeholders for the PCI and PCI-E version but they aren't supported
with this patch.
The bridges are configured based on device-tree properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cputable function pointer for the CPU-side machine
check handling. The semantic is still the same as the old one,
the one in ppc_md. overrides the one in cputable, though
ultimately we'll want to change that so the CPU gets first.
This removes CONFIG_440A which was a problem for multiplatform
kernels and instead fixes up the IVOR at runtime from a setup_cpu
function. The "A" version of the machine check also tweaks the
regs->trap value to differenciate the 2 versions at the C level.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Maple and pasemi both require PCI as does CONFIG_OF_PLATFORM_PCI.
The default setting of CONFIG_ISA_DMA_API is set to match the protection
around the relevant routines in asm/dma.h.
I also had to remove the PMAC platform from the combined build. The
precis is that to build a 64 bit kernel with no PCI, you can only include
pSeries and iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This will allow us to declare const all the statically declared arrrays
of these.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit PCI code tests if "bus" is non-NULL after calling
pci_scan_bus_parented() in one place but not another before
dereferencing it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These hooks ensure that a decrementer interrupt is not pending when
suspending; otherwise, problems may occur on 6xx/7xx/7xxx-based
systems (except for powermacs, which use a separate suspend path).
For example, with deep sleep on the 831x, a pending decrementer will
cause a system freeze because the SoC thinks the decrementer interrupt
would have woken the system, but the core must have interrupts
disabled due to the setup required for deep sleep.
Changed via-pmu.c to use the new ppc_md hooks, and made the arch_*
functions call the generic_* functions unconditionally. -- paulus
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based on an original patch from Arnd Bergmann
<arnd.bergmann@de.ibm.com>
If there's no entry in the mailbox, then a read on the _info file will
return data from an uninitialised variable.
This change returns EOF if there's no mailbox info available instead.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the behavior of spufs when a spu tries a DMA operation
based on a wrong / unavailable address.
Instead of just generating a SIGBUS signal, spufs now
generates a SIGSEGV signal and restarts the problematic DMA operation
after the execution of the application's signal handler. This allows
applications to employ user-level paging systems.
Although the restart_dma function is called before the application's
signal handler, the operation is not actually performed at this time,
since the spu context is already stopped. The operation only takes
place when spu_run is restarted (which happens automatically).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The original spusched_timer was designed to take effect only when
a context is waiting in the runqueue.
This change adds an additional lower-freq timer has been added to
purely handle the spu_load updates. The new timer will be triggered
per LOAD_FREQ ticks.
Signed-off-by: Aegis Lin <aegislin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make most places that use spu_acquire/spu_acquire_saved interruptible,
this allows getting out of the spufs code when e.g. pressing ctrl+c.
There are a few places where we get called e.g. from spufs teardown
routines were we can't simply err out so these are left with a comment.
For now I've also not touched the poll routines because it's open what
libspe would expect in terms of interrupted system calls.
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The simple attr macros currently used by spufs can't deal with the
handlers returning errors, which is required to make the state_mutex
interruptible. This adds a local copy that allows for an error
return from the get/set handlers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change spufs_spu_run so that the context is queued directly to the
scheduler and the controlling thread advances directly to spufs_wait()
for spe errors and exceptions.
nosched contexts are treated the same as before.
Fixes from Christoph Hellwig <hch@lst.de>
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the spu context switch code to not write to reserved bits
of spu interrupt status register.
The architecture book says the reserved fields should be set to zero.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Need to re-check priority after dropping lock. Otherwise, a
more favored context may be preempted.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up spu_run_init so that it does all of the spu
initialization for spufs_run_spu. It initializes the spu context as
much as possible before it activates the spu and writes the runcntl
register.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based on original patches from
Arnd Bergmann <arnd.bergman@de.ibm.com>; and
Luke Browning <lukebr@linux.vnet.ibm.com>
Currently, spu contexts need to be loaded to the SPU in order to take
class 0 and class 1 exceptions.
This change makes the actual interrupt-handlers much simpler (ie,
set the exception information in the context save area), and defers the
handling code to the spufs_handle_class[01] functions, called from
spufs_run_spu.
This should improve the concurrency of the spu scheduling leading to
greater SPU utilization when SPUs are overcommited.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a few #defines for the class 0, 1 and 2 interrupt status bits, and
use them instead of magic numbers when we're setting or checking for
these interrupts.
Also, add a #define for the class 2 mailbox threshold interrupt mask.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When doing a poll on the mbox stat file of a swapped-out context, we
clear the class 0 interrupt status, rather than the class 2 interrupt
status.
This change corrects the poll operation to clear the correct interrupt.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This change encapsulates the spu_privcntl_RW register so that it can
be written through backing ops. This is necessary so that spu contexts
can be initialized and queued to the scheduler in spufs_run_spu.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This change disables the logic that faults-in spu contexts under the
covers from the page fault handler. When a fault requires a runnable
context, the handler will block until the context is scheduled by
other means.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, part of the spufs code (switch.o, lscsa_alloc.o and fault.o)
is compiled directly into the kernel.
This change moves these components of spufs into the kernel.
The lscsa and switch objects are fairly straightforward to move in.
For the fault.o module, we split the fault-handling code into two
parts: a/p/p/c/spu_fault.c and a/p/p/c/spufs/fault.c. The former is for
the in-kernel spu_handle_mm_fault function, and we move the rest of the
fault-handling code into spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a few typos in the spufs scheduler comments
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add platform specific SPU run control routines to the spufs. The current
spufs implementation uses the SPU master run control bit (MFC_SR1[S]) to
control SPE execution, but the PS3 hypervisor does not support the use of
this feature.
This change adds the run control wrapper routies spu_enable_spu() and
spu_disable_spu(). The bare metal routines use the master run control
bit, and the PS3 specific routines use the priv2 run control register.
An outstanding enhancement for the PS3 would be to add a guard to check
for incorrect access to the spu problem state when the spu context is
disabled. This check could be implemented with a flag added to the spu
context that would inhibit mapping problem state pages, and a routine
to unmap spu problem state pages. When the spu is enabled with
ps3_enable_spu() the flag would be set allowing pages to be mapped,
and when the spu is disabled with ps3_disable_spu() the flag would be
cleared and mapped problem state pages would be unmapped.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a module has relocation sections with tens of thousands of
entries, counting the distinct/unique entries only (i.e. no
duplicates) at load time can take tens of seconds and up to minutes.
The sore point is the count_relocs() function which is called as part
of the architecture specific module loading processing path:
-> load_module() generic
-> module_frob_arch_sections() arch specific
-> get_plt_size() 32-bit
-> get_stubs_size() 64-bit
-> count_relocs()
Here count_relocs is being called to find out how many distinct
targets of R_PPC_REL24 relocations there are, since each distinct
target needs a PLT entry or a stub created for it.
The previous counting algorithm has O(n^2) complexity. Basically two
solutions were proposed on the e-mail list: a hash based approach and
a sort based approach.
The hash based approach is the fastest (O(n)) but the has it needs
additional memory and for certain corner cases it could take lots of
memory due to the degeneration of the hash. One such proposal was
submitted here:
http://ozlabs.org/pipermail/linuxppc-dev/2007-June/037641.html
The sort based approach is slower (O(n * log n + n)) but if the
sorting is done "in place" it doesn't need additional memory.
This has O(n + n * log n) complexity with no additional memory
requirements.
This commit implements the in-place sort option.
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There should be an of_node_put when breaking out of a loop that iterates
using for_each_node_by_type.
This was detected and fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_node_by_type;
@@
T *d;
...
for_each_node_by_type(d,...)
{... when != of_node_put(d)
when != e = d
(
return d;
|
+ of_node_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Christian Krafft <krafft@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Erb <djerb@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There should be an of_node_put when breaking out of a loop that iterates
over calls to of_find_all_nodes, as this function does an of_node_get on
the value it returns.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier d;
expression e;
@@
T *d;
...
for (d = NULL; (d = of_find_all_nodes(d)) != NULL; )
{... when != of_node_put(d)
when != e = d
(
return d;
|
+ of_node_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Lucas Woods <woodzy@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a possible NULL pointer dereference inside of strncmp() if
of_get_property() fails.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were using -mno-minimal-toc on everything in arch/powerpc/kernel,
which means that all the functions in there were putting all their
TOC entries in the top-level TOC, and it was overflowing on an
allyesconfig build. For various reasons, prom_init.c does need
-mno-minimal-toc, but the other .c files in there can use sub-TOCs
quite happily. This change is sufficient for now to stop the TOC
overflowing; other directories under arch/powerpc also use
-mno-minimal-toc and could also be changed later if necessary.
Lmbench runs with and without this patch showed no significant speed
differences.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PCI IRQ code has a fallback when the device-tree parsing fails, that
tries to map the interrupt indicated by PCI_INTERRUPT_LINE if the firmware
set something in there. This is a bit fragile but has proven useful in some
cases so far. However, it's causing us to incorrectly try to map interrupt 0
on various setups, so let's prevent that case, as none of the cases where
the fallback is legit should have an IRQ 0.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the PowerPC PCI code to disable IO and/or Memory
decoding on a PCI device when a resource of that type failed to be
allocated. This is done to avoid having unallocated dangling BARs
enabled that might try to decode on top of other devices.
If a proper resource is assigned later on, then pci_enable_device()
will take care of re-enabling decoding.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apple firmware has a strange way to "close" bridge resources by setting
them to some bogus values that overlap RAM (strangely, I haven't seen it
conflicting with DMA so far...). This explicitely closes them to avoid
problems. Previously, they would be closed as a consequence of failing
to be allocated, but this makes it more explicit, and thus the log
message is more explicit too.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The device node for the HT bridge on G5s doesn't contain useful ranges.
We used to give it a bunch of the known PCI space and then punch a "hole"
in it based on where the AGP or PCIe region was. This reworks it to
use the actual register in the bridge that controls the decoding instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This enables the PCI code to see the device that represents the
HT host bridge on the PowerMac G5.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our implementation of pcibios_enable_device() has a couple of problems.
One is that it should not check IORESOURCE_UNSET, as this might be
left dangling after resource assignment (shouldn't but there are
bugs), but instead, we make it check resource->parent which should
be a reliable indication that the resource has been successfully
claimed (it's in the resource tree).
Then, we also need to skip ROM resources that haven't been enabled
as x86 does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It should now be safe to re-assign unassigned resources on 64 bits PowerMac
machines (G5s). This clears pci_probe_only on those.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powermac's use of the pcibios_enable_device_hook() got slightly
broken by the recent PCI merge in that it won't be called for
the "initial" case of assigning resources to a previously
unassigned device. This was an abuse of that hook anyway, so
instead we now use a header quirk.
While at it, we move a #ifdef CONFIG_PPC32 to enclose more code
that is only ever used on 32 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merge the two implementations, based on the previously
fixed up 32 bits one. The pcibios_enable_device_hook in ppc_md
is now available for ppc64 use. Also remove the new unused
"initial" parameter from it and fixup users.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our implementation of pcibios_enable_device() incorrectly ignores
the mask argument and always checks that all resources have been
allocated, which isn't the right thing to do anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The way iSeries manages PCI IO and Memory resources is a bit strange
and is based on overriding the content of those resources with home
cooked ones afterward.
This changes it a bit to better integrate with the new resource handling
so that the "virtual" tokens that iSeries replaces resources with are
done from the proper per-device fixup hook, and bridge resources are
set to enclose that token space. This fixes various things such as
the output of /proc/iomem & ioports, among others. This also fixes up
various boot messages as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code now uses the generic code for assigning unassigned
resources and an algorithm similar to x86 for claiming existing ones.
This works far better than the 64 bits code which basically can only
claim existing ones (pci_probe_only=1) or would fall apart completely.
This merges them so that the new 32 bits implementation is used for both.
64 bits now gets the new PCI flags for controlling the behaviour, though
the old pci_probe_only global is still there for now to be cleared if you
want to.
I kept a pcibios_claim_one_bus() function mostly based on the old 64
bits code for use by the DLPAR hotplug. This will have to be cleaned
up, thought I hope it will work in the meantime.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PCI code in 32 and 64 bits fixes up resources differently.
32 bits uses a header quirk plus handles bridges in pcibios_fixup_bus()
while 64 bits does things in various places depending on whether you
are using OF probing, using PCI hotplug, etc...
This merges those by basically using the 32 bits approach for both,
with various tweaks to make 64 bits work with the new approach.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges the PowerPC 32 and 64 bits version of pcibios_resource_to_bus
and pcibios_bus_to_resource().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds flags the platforms can use to enable domain numbers
in /proc/bus/pci.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code carries an old hack that was only useful for G5
machines. Nowdays, the 32 bits kernel doesn't support any of those
machines anymore so the hack is basically never used, so remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds to the 32 bits PCI code some flags, replacing the old
pci_assign_all_busses global, that allow us to control various
aspects of the PCI probing, such as whether to re-assign all
resources or not, or to not try to assign anything at all.
This also adds the flag x86 already has to avoid ISA alignment
on bridges that don't have ISA forwarding enabled (no legacy
devices on the top level bus) and sets it for PowerMacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PowerPC PCI code has a hack for use by some PowerMacs
to try to re-open PCI<->PCI bridge IO resources that were closed
by the firmware. This is no longer necessary as the generic code
will now do that for us.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the 32 bits PowerPC PCI code use the generic code to assign
resources to devices that had unassigned or conflicting resources.
This allow us to remove the local implementation that was incomplete and
could not assign for example a PCI<->PCI bridge from scratch, which is
needed on various embedded platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a stale & bogus piece of code in 32 bits PCI code that
complains about ISA related alignment issues. Just remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch alters the kernel makefiles to build dtc from the sources
embedded in the previous patch. It also changes the
arch/powerpc/boot/wrapper script to use the embedded dtc, rather than
expecting a copy of dtc already installed on the system.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates a copy of dtc into the kernel source, in
arch/powerpc/boot/dtc-src. This commit only imports the upstream
sources verbatim, a later commit will actually link it into the kernel
Makefiles and use the embedded code during the kernel build.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's nothing in holly.c that needs linux/ide.h, just remove it from
the list of includes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerPC currently doesn't implement pci_set_dma_mask(), which means drivers
calling it will get the generic version in drivers/pci/pci.c.
The powerpc dma mapping ops include a dma_set_mask() hook, which luckily is
not implemented by anyone - so there is no bug in the fact that the hook
is currently never called.
However in future we'll add implementation(s) of dma_set_mask(), and so we
need pci_set_dma_mask() to call the hook.
To save adding a hook to the dma mapping ops, pci-set_consistent_dma_mask()
simply calls the dma_set_mask() hook and then copies the new mask into
dev.coherenet_dma_mask.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have multiple calls to has_feature being inlined, but gcc can't
be sure that the store via get_paca() doesn't alias the path to
cur_cpu_spec->feature.
Reorder to put the calls to read_purr and read_spurr adjacent to each
other. To add a sense of consistency, reorder the remaining lines to
perform parallel steps on purr and scaled purr of each line instead of
calculating and then using one value before going on to the next.
In addition, we can tell gcc that no SPURR means no PURR. The test is
completely hidden in the PURR case, and in the !PURR case the second test
is eliminated resulting in the simple register copy in the out-of-line
branch.
Further, gcc sees get_paca()->system_time referenced several times and
allocates a register to address it (shadowing r13) instead of caching its
value. Reading into a local varable saves the shadow of r13 and removes
a potentially duplicate load (between the nested if and its parent).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If CPU_FTR_PURR is not set, we will never set cpu_purr_data->initialized.
Checking via __get_cpu_var on 64 bit avoids one dependent load compared
to cpu_has_feature in the not-present case, and is always required when
it is present. The code is under CONFIG_VIRT_CPU_ACCOUNTING so 32 bit
will not be affected.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
timer_interrupt() was calculating per_cpu_offset several times, having to
start from the toc because of potential aliasing issues.
Placing both decrementer per_cpu varables in a struct and calculating
the address once with __get_cpu_var results in better code on both 32
and 64 bit.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use __get_cpu_var(x) instead of per_cpu(x, smp_processor_id()), as it
is optimized on ppc64 to access the current cpu's per-cpu offset directly;
it's local_paca.offset instead of TOC->paca[local_paca->processor_id].offset.
This is the trivial portion, two functions with one use each.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
as its only called from time_init, which is __init.
Also remove unneeded forward declaration.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The per-processor interrupt request register and current processor
priority register are only accessed on the current cpu. In fact the
hypervisor doesn't even let us choose which cpu's registers to access.
The only function to use cpu twice is xics_migrate_irqs_away, not a fast
path. But we can cache the result of get_hard_processor_id() instead of
calling get_hard_smp_processor_id(cpu) in a loop across the call to rtas.
Years ago the irq code passed smp_processor_id into get_irq, I thought
we might initialize the CPPR third party at boot as an extra measure of
saftey, and it made the code symmetric with the qirr (queued interrupt
for software generated interrupts), but now it is just extra and
sometimes unneeded work to pass it down.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits the machine definition for celleb into two definitions,
one for celleb_beat, and the other for celleb_native. Though this
looks complex because of sorting some functions, there are no
more semantic changes than that for the splitting.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes mmio_nvram_init() callable unconditionally by providing
a dummy definition when CONFIG_MMIO_NVRAM is not defined.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement MSI support for PA Semi PWRficient platforms. MSI is done
through a special range of sources on the openpic controller, and they're
unfortunately breaking the usual concepts of how sources are programmed:
* The source is calculated as 512 + the value written into the MSI
register
* The vector for this source is added to the source and reported
through IACK
This means that for simplicity, it makes much more sense to just set the
vector to 0 for the source, since that's really the vector we expect to
see from IACK.
Also, the affinity/priority registers will affect 16 sources at a
time. To avoid most (simple) users from being limited by this, allocate
16 sources per device but use only one. This means that there's a total
of 32 sources.
If we get usage scenarions that need more sources, the allocator should
probably be revised to take an alignment argument and size, not just do
natural alignment.
Finally, since I'm already touching the MPIC names on pasemi, rename
the base one from the somewhat odd " PAS-OPIC " to "PASEMI-OPIC".
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit fbd568a3e6 ("Change
synchronize_kernel to _rcu and _sched") changed the deprecated
synchronize_kernel() in HvLpEvent_unregisterHandler() to
synchronize_rcu(). It turns out that it should have been
synchronize_sched().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many operations, as currently used in the wrapper, assume they can
pass NULL and have it be treated as the root node. However, libfdt-wrapper
converts NULL to -1, which is only appropriate when searching for nodes,
and will cause an error otherwise.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
fdt_wrapper_create_node passes a variable called offset to offset_devp(),
which uses said parameter to initialize a local variable called offset.
Due to one of the odder aspects of the C language, the result is an
undefined variable, with no error or warning.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's a dumb simple implementation of fake NUMA nodes for PowerPC.
Fake NUMA nodes can be specified using the following command line option
numa=fake=<node range>
node range is of the format <range1>,<range2>,...<rangeN>
Each of the rangeX parameters is passed using memparse(). I find this
useful for fake NUMA emulation on my simple PowerPC machine. I've
tested it on a non-numa box with the following arguments:
numa=fake=1G
numa=fake=1G,2G
name=fake=1G,512M,2G
numa=fake=1500M,2800M mem=3500M
numa=fake=1G mem=512M
numa=fake=1G mem=1G
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Optimize MPIC IPIs, by passing in the IPI number as the argument to the
handler, since all we did was translate it back based on which mpic
the interrupt came though on (and that was always the primary mpic).
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We're currently getting a warning from not checking the result of
sysfs_create_group, which is declared as __must_check.
This change introduces appropriate error-handling for
spu_add_sysdev_attr_group()
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, we have a possibilty that the SLBs setup during context
switch don't cover the entirety of the necessary lscsa and code
regions, if these regions cross a segment boundary.
This change checks the start and end of each region, and inserts a SLB
entry for each, if unique. We also remove the assumption that the
spu_save_code and spu_restore_code reside in the same segment, by using
the specific code array for save and restore.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a function spu_64k_pages_available(), so that we can abstract the
explicity use of mmu_psize_defs() in lssca_alloc.c
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that we have a helper function to setup a SPU SLB, use it for
__spu_trap_data_seq.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, the SPU context switch code (spufs/switch.c) sets up the
SPU's SLBs directly, which requires some low-level mm stuff.
This change moves the kernel SLB setup to spu_base.c, by exposing
a function spu_setup_kernel_slbs() to do this setup. This allows us
to remove the low-level mm code from switch.c, making it possible
to later move switch.c to the spufs module.
Also, add a struct spu_slb for the cases where we need to deal with
SLB entries.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch changes the way we check for the existence of
vicinity property in spe device nodes.
The new implementation does not depend on having an initialized
cbe_spu_info[0].spus, and checks for presence of vicinity in all
nodes, not only in the first one.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Export force_sig_info to allow signals to be sent from a modular spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix debug_bus_control and group_control PMU register values set up in
set_pm_event(). Initialize variables before calling set_pm_event().
Delete unused static array and code that initialized it.
Rename constant to better reflect usage.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The pm_interval register in the Cell PMU is read/write, but was implemented in
the kernel as write-only. Previously, the written value was saved in a "shadow"
copy so calls to cbe_read_pm() could return the value.
Perfmon2 needs to be able to read the current values of pm_interval, so change
cbe_read_pm() to read the actual register instead of the "shadow" copy. There
is currently no code in the kernel that tries to read the pm_interval register
with cbe_read_pm() (expecting to receive the "shadow" value), so this should
not break any existing code.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Updates the ucc_geth device driver to check the new rx-clock-name and
tx-clock-name properties first. If present, it uses the new function
qe_clock_source() to obtain the clock source. Otherwise, it checks the
deprecated rx-clock and tx-clock properties.
Update the device trees for 832x, 836x, and 8568 to contain the new property
names only.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it's impossible to build a ps3_defconfig which will reboot
without modules installed. This makes it all too easy to find yourself
with a PS3 that won't reboot.
This is because the system manager driver, which provides the reboot
mechanism, is only selectable if PS3_ADVANCED is set, else it defaults
to m. In ps3_defconfig PS3_ADVANCED is not set, therefore the system
manager is built as a module.
It would be desirable IMHO for the defconfig to produce a kernel that
boots and reboots, without needing modules to be installed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add function qe_clock_source() which takes a string containing the name of a
QE clock source (as is typically found in device trees) and returns the
matching enum qe_clock value.
Update booting-without-of.txt to indicate that the UCC properties rx-clock
and tx-clock are deprecated and replaced with rx-clock-name and tx-clock-name,
which use strings instead of numbers to indicate QE clock sources.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes rounding bug in emulation for double float operating on PowerPC platform.
When pack double float operand, it need to truncate the tail due to the limited precision.
If the truncated part is not zero, the last bit of work bit (totally 3 bits) need to '|' 1.
This patch is completed in _FP_FRAC_SRS_2(X,N,sz) (arch/powerpc/math-emu/op-2.h).
Originally the code leftwards rotates the operand to just keep the truncated part,
then check whether it is zero. However, the number it rotates is not correct when
N is not smaller than _FP_W_TYPE_SIZE, and it will cause the work bit '|' 1 in the improper case.
This patch fixes this issue.
Signed-off-by: Liu Yu <b13201@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Printk was observed to hang during module unload due to a limited
window of characters that may be sent to the hypervisor. The window
only reexpands when we receive an ack from the HV and the spinlock here
prevents us from ever processing that ack. This fixes it by dropping
the lock before doing the printk, then looping back to the top to
reacquire the lock.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch moves the CPM command handling into commproc.c
for CPM1 and cpm2_common.c. This is yet another preparation
to get rid of drivers accessing the CPM via the global cpmp.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
PORTA and PORTB have odr registers, as well. However, the PORTB odr
register is only 16bit.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Verified on mpc866ads. This version has muram and brg nodes added to dts
to get the things work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
This was recently made configurable, and needs to be set for these boards.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove exports of __res and cpm_install_handler/cpm_free_handler. Remove
cpm_install_handler/cpm_free_handler from the commproc.h as well. Both
were used for ARCH=ppc and aren't defined for ARCH=powerpc.
CC arch/powerpc/kernel/ppc_ksyms.o
arch/powerpc/kernel/ppc_ksyms.c:180: error: '__res' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:180: warning: type defaults to 'int' in declaration of '__res'
make[1]: *** [arch/powerpc/kernel/ppc_ksyms.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
LD .tmp_vmlinux1
arch/powerpc/kernel/built-in.o:(__ksymtab+0x198): undefined reference to `cpm_free_handler'
arch/powerpc/kernel/built-in.o:(__ksymtab+0x1a0): undefined reference to `cpm_install_handler'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Only external interrupts in edge detect mode support ack operation.
Therefore, in most cases ack is not needed. The patch makes ipic
ack only when it's needed. This could boost over all system performance.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added aliases nodes for kurobox, 83xx, 85xx, and 86xx platforms.
This included added labels and cell-index properties for serial and
pci nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Removed address fields in ethernet nodes
* Removed #address-cells, #size-cells from gianfar nodes
* Added cell-index to gianfar and ucc ethernet nodes
* Added enet[0..3] labels
* Renamed compatible node for gianfar mdio to "fsl,gianfar-mdio"
* Removed device_type = "mdio"
The matching for gianfar mdio still supports the old "mdio"/"gianfar" combo
but it is now considered deprecated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The addition of the aliases node is needed for U-Boot
and, eventually, cuImage, to help locate the proper
nodes reliably when using the libfdt approach.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
qe_setbrg() currently takes an integer to indicate the BRG number. Change that
to take an enum qe_clock instead, since this enum is intended to represent
clock sources.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC837x MDS is a new member of Freescale MDS reference system.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These interrupts are introduced by the latest Freescale SoC
such as MPC837x.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
isel (Integer Select) is a new user space instruction in the
PowerISA 2.04 spec. Not all processors implement it so lets emulate
to ensure code built with isel will run everywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This makes the early debug option force the console loglevel
to the max. The early debug option is meant to catch messages very
early in the kernel boot process, in many cases, before the kernel
has a chance to parse the "debug" command line argument. Thus it
makes sense when CONFIG_PPC_EARLY_DEBUG is set, to force the console
log level to the max at boot time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a variant of of_translate_address that uses the dma-ranges
property instead of "ranges", it's to be used by PCI code in parsing
the dma-ranges property.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes "volatile" from the MMIO pointer udbg_comport
in udbg_16550.c driver, it's useless and makes checkpatch.pl
complain when adding things to this file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code will display a rather scary error message
PCI: Cannot allocate resource region N of device XXX
at boot when the existing setup of a device as left by the
firmware doesn't match the kernel needs and the device needs
to be moved. This is often not an error at all, as the kernel
will generally easily reallocate the device elsewhere.
This changes the message to something less scary and lowers
its level from error to warning.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit powerpc resource fixup code uses unsigned longs to do the
offsetting of resources which overflows on platforms such as 4xx where
resources can be 64 bits.
This fixes it by using resource_size_t instead.
However, the IO stuff does rely on some 32 bits arithmetic, so we hack
by cropping the result of the fixups for IO resources with a 32 bits
mask.
This isn't the prettiest but should work for now until we change the
32 bits PCI code to do IO mappings like 64 bits does, within a reserved
are of the kernel address space.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges the 32-bit and 64-bit implementations of
pci_process_bridge_OF_ranges(). The new function is cleaner than both
the old ones, and supports 64 bits ranges on ppc32 which is necessary
for the 4xx port.
It also adds some better (hopefully) output to the kernel log which
should help diagnose problems and makes better use of existing OF
parsing helpers (avoiding a few bugs of both implementations along
the way).
There are still a few unfortunate ifdef's but there is no way around
these for now at least not until some other bits of the PCI code are
made common.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This defines isa_mem_base on both 32 and 64 bits (it used to be 32 bits
only). This avoids a few ifdef's in later patches and potentially can
allow support for VGA text mode on 64 bits powerpc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that earlier patches have switched the bootwrapper to using libfdt
for device tree manipulation, this patch removes the now unused
flatdevtree.c and related files.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates libfdt (from the source embedded in an earlier
commit) into the wrapper.a library used by the bootwrapper. This
includes adding a libfdt_env.h file, which the libfdt sources need in
order to integrate into the bootwrapper environment, and a
libfdt-wrapper.c which provides glue to connect the bootwrapper's
abstract device tree callbacks to the libfdt functions.
In addition, this changes the various wrapper and platform files to
use libfdt functions instead of the older flatdevtree.c library.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates a copy of dtc libfdt into the kernel source, in
arch/powerpc/boot/libfdt. This only imports the upstream sources
verbatim, later patches are needed to actually link it into the kernel
Makefiles.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There was only one global function in vpdinfo.c and it was only called
from pci.c, so merge them and make the function static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we hardwire the number of SLBs to 64, but PAPR says we
should use the ibm,slb-size property to obtain the number of SLB
entries. This uses this property instead of assuming 64. If no
property is found, we assume 64 entries as before.
This soft patches the SLB handler, so it shouldn't change performance
at all.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and it becomes clear that we should use zalloc_maybe_bootmem.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also remove another unnecessary forward declaration.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It only needs the iommu_table address. It also makes use of the node
name to print error messages. So just pass it the things it needs.
This reduces the places that know about the pci_dn by one.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 'data' member of proc_ppc64_lparcfg is unused, but the lparcfg
module's init routine allocates 4K for it.
Remove the code which allocates and frees this buffer.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for native CBE on Celleb, that is, without the BEAT
hypervisor. Many codes in platforms/cell/ are used in native CBE
environment.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following link error with CONFIG_PPC_CELL_NATIVE=y and
CONFIG_PPC_CELL_BLADE=n:
arch/powerpc/platforms/built-in.o: In function `.cell_setup_arch':
setup.c:(.init.text+0xe80): undefined reference to `.mmio_nvram_init'
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also use of_unregister_driver to implement of_unregister_platform_driver.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerMac and CHRP/BriQ platforms have quirks to switch some IDE
controllers from legacy mode to fully native mode. Those quirks
however will not work properly anymore due to a change to the
generic code to better handle legacy IDE resources.
This fixes it by moving those quirk to "early" quirks (so they
run before resources are probed for the devices) and clearing
all BARs after the conversion to force a reallocation of sane
values.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More than just "AXON" version of EMAC RGMII supports MDIO, so replace
the current test with a generic property in the device-tree that
indicates such support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The size of swapper_pg_dir is 8k instead of 4k when using 64-bit PTEs
(CONFIG_PTE_64BIT).
This was reported by Cedric Hombourger <chombourger@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This updates all the defconfigs in arch/powerpc/configs except iseries
and ps3, which were updated by the preceding commits.
This mostly takes the defaults, except that I turned on tickless idle
and high-resolution timers for everything, and turned off instrumentation
support and "Fair group CPU scheduler" for the smaller/embedded platforms.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The notable changes here are the enabling of NO_HZ and HIGH_RES_TIMERS.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The commit fa13a5a1f2 (sched: restore
deterministic CPU accounting on powerpc), unconditionally calls
update_process_tick() in system context. In the deterministic
accounting case this is the correct thing to do. However, in the
non-deterministic accounting case we need to not do this, since doing
this results in the time accounted as hardware irq time being
artificially elevated.
Also this collapses 2 consecutive '#ifdef CONFIG_VIRT_CPU_ACCOUNTING'
checks in time.h into one for neatness.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a 'bootwrapper_install' make target for the powerpc
architecture, which installs the wrapper script, intermediate object
files and device-tree sources for later use.
This will then allow bootable zImages to be created other than in the
context of a kernel build.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's possible that the executables which are built as helpers for the
bootwrapper stuff might end up in a different place to the intermediate
object files. Handle that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If a .dts file is given to the bootwrapper script without a full path
name, look in a sensible place for it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper script currently generates an 'otheros.bld' file in
addition to the file specified by the -o option, when asked to build a
wrapper for PS3.
It should do that in the same directory as the output, not the directory
where the wrapper objects are kept (which might potentially not be
writable when the script runs).
Arguably, the 'otheros.bld' ought to be created with the filename
specified as the -o argument. But that's a more intrusive change.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds checking for NULL returned value from of_get_property to
prevent possible NULL pointer dereference in the case when expected
properties are not present.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert #include of asm/of_{platform, device}.h into
linux/of_{platform,device}.h for remaining arch/powerpc files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert #include of asm/of_{platform, device}.h into
linux/of_{platform,device}.h for a few scattered platforms.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix up the module information for gpio-mdio, it wouldn't load
because of lacking license, and wouldn't auto-load because of missing
MODULE_DEVICE_TABLE.
Signed-off-by: Olof Johansson <olof@lixom.net>
It is already declared in ppc-pci.h which is included.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/iseries/setup.c:111:27: warning: constant 0x100000000 is so big it is long
arch/powerpc/platforms/iseries/setup.c:113:23: warning: constant 0x100000000 is so big it is long
arch/powerpc/platforms/iseries/setup.c:117:27: warning: constant 0x000fffffffffffff is so big it is long
arch/powerpc/platforms/iseries/setup.c:127:28: warning: constant 0x100000000 is so big it is long
arch/powerpc/platforms/iseries/setup.c:129:24: warning: constant 0x100000000 is so big it is long
arch/powerpc/platforms/iseries/setup.c:233:5: warning: constant 0x000fffffffffffff is so big it is long
arch/powerpc/platforms/iseries/setup.c:235:5: warning: constant 0x000fffffffffffff is so big it is long
arch/powerpc/platforms/iseries/setup.c:319:6: warning: symbol 'mschunks_alloc' was not declared. Should it be static?
arch/powerpc/platforms/iseries/setup.c:661:6: warning: symbol 'iSeries_early_setup' was not declared. Should it be static?
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes sparse warning:
arch/powerpc/platforms/iseries/pci.c:169:13: warning: symbol 'iSeries_pci_final_fixup' was not declared. Should it be static?
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
since it's not used outside of arch/powerpc/kernel/pci-common.c.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a function to xmon to dump the content of the 44x processor
TLB with a little bit of decoding (but not much).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do not wait for the pci slot status before reporting an error
to the device driver. Some systems may take many seconds to
report the slot status, and this can confuse unsuspecting
device drivers.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an "empty" slot is failing, make sure its a permanent failure;
else process the error normally.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Perform all error checking at the "partitonable endpoint"
of the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/powermac/time.c:88: warning: 'to_rtc_time' defined but not used
This fixes the warning by making the relevant code depend on the
users.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
prod_processor() is unused, and that's a good thing, since it does not
supply the required proc id parameter to H_PROD.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up the SMT thread handling, removing some hard coded
assumptions and providing a set of helpers to convert between linux
cpu numbers, thread numbers and cores.
This implementation requires the number of threads per core to be a
power of 2 and identical on all cores in the system, but it's an
implementation detail, not an API requirement and so this limitation
can be lifted in the future if anybody ever needs it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit a2b51812a4.
It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines. The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called. Until that is clarified I'm reverting this commit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use smp_send_stop() to move all cpus besides the one executing reboot
into a hold loop, to keep them from being in powersavings mode at the
time of reboot.
Signed-off-by: Olof Johansson <olof@lixom.net>
When the PWRficient cpus are entered into powersavings states, the
astate is automatically dropped down to 0. While we still restore it
when we come out of idle, it can still cause some weird effects with
respect to performance (especially since it takes a while to ramp up to
higher astates).
So, to avoid this, don't enter power savings when the cpufreq driver
(or user) has set higher astates than 0.
The restore is still required, since there's a chance the astate has
been raised from the other cpu while the idling one was asleep.
Signed-off-by: Olof Johansson <olof@lixom.net>