Use signal resampling tuning for the UHS and HS200 modes.
Instead of trying to get the *best* resampling setting with complex
window calculation, we just stop on the first working setting.
If the tuning setting later proves unstable, we will just continue the
tuning where we left it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This remove all the code related to phase settings. Using the Rx phase
for tuning has not been reliable. We had several issues over the past
months, on both v2 and v3 mmc chips After discussing the issue matter
with Amlogic, They suggested to set a phase shift of 180 between Core and
Tx and use signal resampling for the tuning.
Since we won't be playing with the phase anymore, let's remove all the
clock code related to it and set the appropriate value on init.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Activating DDR in the Amlogic mmc controller, among other things, will
divide the output clock by 2. So by activating it with clock on, we are
creating a glitch on the output.
Instead, let's deal with DDR when the clock output is off, when setting
the clock.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At the moment, all our attempts to enable HS400 on Amlogic chipsets have
been unsuccessful or unreliable. Until we can figure out how to enable this
mode safely and reliably, let's force it off.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason for another device to request the MMC irq. It should
only be used the MMC device, so remove IRQ_SHARED and replace by
IRQ_ONESHOT as we don't the irq to fire again until the irq thread is
done
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is merely a clean up. It makes sense to only ack raised irqs
instead of acking everything all the time.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is already a function available to poll a register until a
condition is met. Let's use it instead of open coding it.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bb36489032 ("mmc: meson-gx: Free irq in release() callback")
changed the _probe code to use request_threaded_irq() instead of
devm_request_threaded_irq().
Unfortunately this removes a fallback for the interrupt name:
devm_request_threaded_irq() uses the device name as fallback if the
given IRQ name is NULL. request_threaded_irq() has no such fallback,
thus /proc/interrupts shows "(null)" instead.
Explicitly pass the dev_name() so we get the IRQ name shown in
/proc/interrupts again.
While here, also fix the indentation of the request_threaded_irq()
parameter list.
Fixes: bb36489032 ("mmc: meson-gx: Free irq in release() callback")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because the irq was requested through device managed resources API
(devm_request_threaded_irq()) it was freed after meson_mmc_remove()
completion, thus after mmc_free_host() has reclaimed meson_host memory.
As this irq is IRQF_SHARED, while using CONFIG_DEBUG_SHIRQ, its handler
get called by free_irq(). So meson_mmc_irq() was called after the
meson_host memory reclamation and was using invalid memory.
We ended up with the following scenario:
device_release_driver()
meson_mmc_remove()
mmc_free_host() /* Freeing host memory */
...
devres_release_all()
devm_irq_release()
__free_irq()
meson_mmc_irq() /* Uses freed memory */
To avoid this, the irq is released in meson_mmc_remove() and in
mseon_mmc_probe() error path before mmc_free_host() gets called.
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With some eMMC devices, there is still issues with the new phase
settings. Enabling signal resampling seems to solve the problem
for these.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Align the default Core and Tx phase with the SoC vendor tree.
Even if the Tx phase is different from what the documentation
recommends, it seems to provide better results.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The spinlock is only used within the irq handler so it does not
seem very useful.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On errors, if we don't stop the descriptor chain, it may continue to
run and raise IRQ after we have called mmc_request_done(). This is bad
because we won't be able to get cmd anymore and properly deal with the
IRQ.
This patch makes sure the descriptor chain is stopped before
calling mmc_request_done()
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trigger the reset line of the mmc controller while probing, if available.
The reset should be optional for now, at least until all related DT nodes
have the reset property.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Explicitly update the docomentation to support the Meson-AXG platform.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Introduce the compatible data to cover the register offset & mask
change of the eMMC controller in Amlogic's Meson-AXG SoC.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
This reverts commit 0a44697627.
This commit was initially intended to fix problems with hs200 and hs400
on some boards, mainly the odroid-c2. The OC2 (Rev 0.2) I have performs
well in this modes, so I could not confirm these issues.
We've had several reports about the issues being still present on (some)
OC2, so apparently, this change does not do what it was supposed to do.
Maybe the eMMC signal quality is on the edge on the board. This may
explain the variability we see in term of stability, but this is just a
guess. Lowering the max_frequency to 100Mhz seems to do trick for those
affected by the issue
Worse, the commit created new issues (CRC errors and hangs) on other
boards, such as the kvim 1 and 2, the p200 or the libretech-cc.
According to amlogic, the Tx phase should not be tuned and left in its
default configuration, so it is best to just revert the commit.
Fixes: 0a44697627 ("mmc: meson-gx: include tx phase in the tuning process")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Meson GX MMC driver fails to build after commit 23c35f48f5
("pinctrl: remove include file from <linux/device.h>") because it relies
on the pinctrl/consumer.h being pulled in by the device.h header
implicitly.
Include the header explicitly to avoid the build failure.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has been reported that some platforms (odroid-c2) may require
a different tx phase setting to operate at high speed (hs200 and hs400)
To improve the situation, this patch includes tx phase in the tuning
process.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resetting the phase when POWER_ON is set the set_ios() call means that the
phase is reset almost every time the set_ios() is called, while the
expected behavior was to reset the phase on a power cycle.
This had gone unnoticed until now because in all mode (except hs400) the
tuning is done after the last to set_ios(). In such case, the tuning
result is used anyway. In HS400, there are a few calls to set_ios() after
the tuning is done, overwriting the tuning result.
Resetting the phase on POWER_UP instead of POWER_ON solve the problem.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using CLK_DIVIDER_ROUND_CLOSEST is unsafe as the mmc clock could be
rounded to a rate higher the specified rate. Removing this flag ensure
that, if the rate needs to be rounded, it will be rounded down.
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using __bf_shf does not compile on arm 32 architecture.
This has gone unnoticed till now cause the driver is only used on arm64.
In addition, __bf_shf was already used in the driver without any issue.
It was used on a constant value, so the call was probably optimized
away.
Replace __bf_shf by __ffs fixes the problem
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rework tuning function of the rx phase. Now that the phase can be
more precisely set using CCF, test more phase setting and find the
largest working window. Then the tuning selected is the one at the
center of the window.
This rework allows to use new modes, such as UHS SDR50
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initial default tx phase was set to 0 while the datasheet recommends 270.
Some cards fails to initialize with this setting and eMMC mode DDR52 does
not work.
Changing this setting to 270 fixes these issues, without any regression
so far
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement voltage switch callback (shamelessly copied from sunxi mmc
driver). This allow, with the appropriate tuning function, to use
SD ultra high speed modes.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Several phases can be controlled on the meson-gx controller, the core, tx
and rx clock phase. The tx and rx uses delays to allow more fine grained
setting of the phase. To properly compute the phase using delays,
accessing the clock rate is necessary.
Instead of ad-hoc functions, use the common clock framework to set the
clock phases (and access the clock rate while doing it).
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the card_busy callback to be able to verify that the
card is done dealing with voltage switch, when the support is
added later on.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It seems that the mmc clock is also used and required, somehow, by
the controller itself.
It is shown during init, when writing to CFG while the divider is set
to 0 will crash the SoC. During a voltage switch, the controller may
crash and the card may then fail to exit busy state if the clock is
stopped.
To avoid this, it is best to keep the clock running for the controller,
except during rate change. However, we still need to be able to gate
the clock out of the SoC. Let's use the pinmux for this, and fallback
to gpio mode (pulled-down) when we need to gate the clock
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In DDR modes, meson mmc controller requires an input rate twice as fast
as the output rate
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Thanks to devm, carrying the clock structure around after init is not
necessary. Rework the function to remove these from the controller host
data.
Finally, set initial mmc clock rate before enabling it, simplifying the
exit condition.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clean-up clk_set function to prepare the next changes (DDR and clk-stop)
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove conditional write of cfg register. Warn if set_clk fails for some
reason. Consistently use host->dev instead of mixing with mmc_dev(mmc)
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cfg init function overwrite values set in the clk init function
Remove the cfg pokes from the clk init. Actually, trying to use
the CLK_AUTO, like initially tried in clk_init, would break
the card initialization
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On boot, the clock divider value is 0 which is a weird unsupported value.
For example, accessing the cfg register with this value set would crash
the SoC.
Previous change removed 0 as possible value for CCF but forgot to properly
initialize the register before registering the clock. This leads to the
CCF finding an illegal value, which it complains about.
Initialize the register properly in a standalone patch so the fix can be
picked up if necessary. The change this fixed is: "mmc: meson-gx: remove
CLK_DIVIDER_ALLOW_ZERO clock flag".
Reported-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove unused clock rate defines. These should not be defined but
requested from the clock framework.
Also correct typo on the DELAY register
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove CLK_DIVIDER_ALLOW_ZERO. This flag means that a 1 based divider
with a 0 value will behave as a bypass clock
The mmc divider does not behave like this, a 0 value disables the clock
Remove this flag so CCF never allows a 0 value on this clock
Fixes: 51c5d8447b ("MMC: meson: initial support for GX platforms")
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CCF generic mux will shift the mask using the value defined in shift
Define the mask accordingly
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There have been reports about SDIO failing with certain WiFi chips in
descriptor chain mode. SD / eMMC are working fine.
So let's fall back to bounce buffer mode for command SD_IO_RW_EXTENDED.
This was reported to fix the error.
Fixes: 79ed05e329 "mmc: meson-gx: add support for descriptor chain mode"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far a bounce buffer is used to serialize the scatterlist(s).
This overhead can be avoided by switching to descriptor chain mode.
As result the performance is drastically improved. On a Odroid-C2 with
a 128 GB eMMC module raw reads reach 140 MB/s.
Prerequisite for descriptor chain mode is that all scatterlist buffers
are 8 byte aligned for 64-bit DMA. That's not always the case, at least
the brcmfmac SDIO WiFi driver is known to cause problems.
Therefore, for each request, check upfront whether all scatterlist
buffers are 8 byte aligned and fall back to bounce buffer mode if
that's not the case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds basic tuning which changes the rx clock phase only
until a working setting is found.
On a Odroid C2 with 128GB eMMC card and 200 MHz MMC clock only
180° rx clock phase make the system boot w/o CRC errors.
With other MMC devices / clock speeds this might be different,
therefore don't change the driver config in general.
When retuning skip the currently active parameter set. This avoids
the current problematic config to be chosen again if it causes CRC
errors just occasionally.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce struct meson_tuning_params for storing the clock phase
configurations. There's no functional change because tx and rx
clock phase were implicitely set to CLK_PHASE_0 before.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out setting the response configuration bits thus further reducing
complexity of function meson_mmc_start_cmd.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out setting the block size. This also contributes to reducing
complexity of function meson_mmc_start_cmd.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD23 mode (use "set block count" command before transferring multiple
data blocks) typically is more performant as host / card know upfront
how many data blocks to expect. Therefore add support for this mode to
the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we use a fixed timeout of 4s for all data transfers. Switch
to dynamic timeout values by making use of data->timeout_ns.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far the driver name is used as interrupt description, therefore in
/proc/interrupts it's not possible to tell which interrupt belongs to
which port. Change this by switching to NULL what causes the default
(device name) to be used. In our case that's the DT node name.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jerome Brunet
Martin Blumenstingl
Andreas Fenkart
Remi Pommarel
Nan Li
Thierry Reding
Arvind Yadav
Wolfram Sang
Heiner Kallweit