Device tree source file for the PPC405 Walnut evaluation board.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Commit 804ace8881 changed the behavior of how compatible nodes are found.
This highlighted a bug on the Bamboo board where it wasn't probing the bus
specified in the DTS file. We fix it by being explicit about which bus to
probe.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbvear.id.au>
The patch below removes the dtc incantation instructions from the
in-kernel DTS files. It's not needed, and is prone to being
out-of-date most of the time.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The names of STI and CLI macros were derived from i386 arch historically,
but their name are incomprehensible.
So, for easy to understand, rename these macros to ENABLE_INTERRUPTS
and DISABLE_INTERRUPTS, respectively.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Apparently XEN does not keep the contents of the 48-bit gdt_48 data
structure that is passed to lgdt in the XEN machine state. Instead it
appears to save the _address_ of the 48-bit descriptor
somewhere. Unfortunately this data happens to reside on the stack and
is probably no longer availiable at the time of the actual protected
mode jump.
This is Xen bug but given that there is a one-line patch to work
around this problem, the linux kernel should probably do this. My fix
is to make the gdt_48 description in setup_gdt static (in setup_idt
this is already the case). This allows the kernel to boot under
Xen HVM again.
Signed-off-by: Christian Ehrhardt <lk@c--e.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
- Separate sys_call_table from arch/m32r/kernel/entry.S and
move it to arch/m32r/kernel/system_call.S.
- Change sys_call_table section from .data to .rodata.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
If no IRQ request is found in the IRQ check of ei_handler,
we can exit directly by jumping "restore_all", instead of via
"ret_from_intr".
This modification is also likely effective for IPI operations,
because scheduler call never happen at the exit of IPIs.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Simplify and clean up messy ei_handler code in arch/m32r/kernel/entry.S.
- Remove ifdef's for CONFIG_CHIP_* configulations.
- Rearrange the M32700 workaround code.
- Remove the messy platform-dependent interrupt check routines and
consolidate them to common INT0/INT1/INT2 check routines for all
platforms with cascaded interrupt controllers.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
On some m32r platforms, cascaded ICUs are used.
This patch is required to simplify ei_handler and consolidate platform-
dependent ICU check routines.
platform ICU/INT1 ICU/INT0 ICU/INT2
-------------- -------- -------- --------
m32104ut o - -
m32700ut o o o
opsput o o o
usrv o - -
(others) - - -
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
After my last patch we have a new header file for HP simulator use.
Here's code to use it for stuff that used to have `extern' statements
inline in the code. Functionality should not change with this patch.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch cleans up the `enable early console for SKI' patch
(471e7a4484), and
1. potentially allows the gensparse_defconfig to work again.
(there are other problems running a generic kernel on Ski)
2. fixes the `console registered twice' problem.
3. Cleans up the code by moving the `extern hpsim_cons' declaration to
a new asm/hpsim.h file.
Thanks to Jes for comments.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When dumping memory via sysrq-m it is possible to take a bogus NMI watchdog
or softlockup watchdog because the dump can take a long time on big memory
systems.
Occasionally tickle the watchdog when doing the dump.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add additional support for CPU disable on SN platforms.
Correctly setup the smp_affinity mask for I/O error IRQs.
Restrict the use of the feature to Altix 4000 and 450 systems
running with a CPU disable capable PROM, and do not allow disabling
of CPU 0.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
vmalloc() returns a void pointer - no need to cast it.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
lguest didn't initialize the kernel stack the way a real i386 kernel
does, and ended up triggering a corner-case in the stack frame checking
that doesn't happen on naive i386, and that the stack dumping didn't
handle quite right.
This makes the frame handling more correct, and tries to clarify the
code at the same time so that it's a bit more obvious what is going on.
Thanks to Rusty Russell for debugging the lguest failure-
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The VESA BIOS is specified to be register-clean. However, we have now
found at least one system which violates that. Thus, be as paranoid
about VESA calls as about everything else.
Huge thanks to Will Simoneau for reporting, diagnosing, and testing
this out on Dell Inspiron 5150.
Cc: Will Simoneau <simoneau@ele.uri.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For hugepage mappings, the file offset, like the address and size, needs to
be aligned to the size of a hugepage.
In commit 68589bc353, the check for this was
moved into prepare_hugepage_range() along with the address and size checks.
But since BenH's rework of the get_unmapped_area() paths leading up to
commit 4b1d89290b, prepare_hugepage_range()
is only called for MAP_FIXED mappings, not for other mappings. This means
we're no longer ever checking for an aligned offset - I've confirmed that
mmap() will (apparently) succeed with a misaligned offset on both powerpc
and i386 at least.
This patch restores the check, removing it from prepare_hugepage_range()
and putting it back into hugetlbfs_file_mmap(). I'm putting it there,
rather than in the get_unmapped_area() path so it only needs to go in one
place, than separately in the half-dozen or so arch-specific
implementations of hugetlb_get_unmapped_area().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dependencies of CONFIG_SUSPEND and CONFIG_HIBERNATION introduced by commit
296699de6b "Introduce CONFIG_SUSPEND for
suspend-to-Ram and standby" are incorrect, as they don't cover the facts that
(1) not all architectures support suspend and (2) SMP hibernation is only
possible on X86 and PPC64 (if CONFIG_PPC64_SWSUSP is set).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the name of the spi_txx9 driver (and their in-tree user)
instead of MODULE_ALIAS workaround. This would be preferable in the
long term.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stop UML crashing when trying to dump a process core on x86_64. This is the
minimal fix to stop the crash - more things are broken here, and patches are
forthcoming.
The immediate thing to do is define ELF_CORE_COPY_REGS and
ELF_CORE_COPY_FPREGS. Defining ELF_CORE_COPY_FPREGS allows dump_fpu to go
away. It is defined in terms of save_fp_registers, so that needs to be added.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a class of bugs in the UML linker scripts which caused section boundary
variables to sometimes not line up with their sections.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) sun4{u,v}_build_msi() have improper return value handling.
We should always return negative error codes, instead of
using the magic value "0" which could in fact be a valid
MSI number.
2) sun4{u,v}_build_msi() should return -ENOMEM instead of
calling prom_prom() halt with kzalloc() of the interrupt
data fails.
3) We 'remembered' the MSI number using a singleton in the
struct device archdata area, this doesn't work for MSI-X
which can cause multiple MSIs assosciated with one device.
Delete that archdata member, and instead store the MSI
number in the IRQ chip data area.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes we were using 32-bit values and the top bits were
getting inadvertantly chopped off. This will matter for the
forthcoming Fire controller MSI support.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] PS3: Fix bug where the major version part is not compared
[POWERPC] Update defconfigs
[POWERPC] spufs: Don't call spu_run_init from spu_reacquire_runnable
[POWERPC] spufs: Fix update of mailbox status register during backed wbox write
[POWERPC] spu_manage: fix spu_unit_number for celleb device tree
[POWERPC] Update defconfigs
[POWERPC] Flush registers to proper task context
Another fallout from the removal of #include <linux/fs.h> from mm.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the bug that the major version part of the firmware version number
is ignored in the comparison done by ps3_compare_firmware_version
because the difference of two 64-bit quantities is returned as an int.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During GPIO testing on PiMX1 board there has been revealed
problem with some pins input functions. The GIUS bit has
to be set for inputs to work reliably too. It is surprising
that input worked on some inputs with incorrect setup before.
DR is not mandatory, but it ensures stable constant level
on internal traces.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a major bug which was happening when a SPU thread advances
its execution right after being restored to a SPU. A potentially
outdated NPC value was being (re)written to the SPU.
So, spu_run_init, in this case, was either not doing anything relevant,
or breaking the execution of the SPU thread.
This fixes a common problem of losing a mailbox write when it was done
to a saved context.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a process writes into the inbound spu mailbox (wbox) while the
context is saved, we accidentally break the contents of the mb_stat_R
register by clearing other entries of the mailbox status register. This
can cause the user side to hang.
This change fixes the problem by only altering the appropriate bits
of the mailbox status register during a backing-store write.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a regression introduced with 2.6.23-rc4 after on some
confusion about the device tree interfaces.
IBM QS21 device trees provide "physical-id", so we changed the code to
run on that and remain compatible with all IBM machines.
However, the Toshiba Celleb device tree provides the "unit-id" property,
which was in the Linux code, but never used in this way on IBM hardware.
Legacy device tree used the reg property for the physical id of an spe.
This patch fixes find_spu_unit_number to look for the spu id in that order.
The length is checked to avoid misinterpretation in case the attributes
unit-id or reg do not contain the id.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
When we flush register state for FP, Altivec, or SPE in flush_*_to_thread
we need to respect the task_struct that the caller has passed to us.
Most cases we are called with current, however sometimes (ptrace) we may
be passed a different task_struct.
This showed up when using gdbserver debugging a simple program that used
floating point. When gdb tried to show the FP regs they all showed up as
0, because the child's FP registers were never properly flushed to memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The pending interrupts can be remaining at boot up time on some
platform. This will cause spurious interrupts when interrupt is
enabled for the first time. This patch clears IVR at the CPU
initialization to eliminate such spurious interrupts.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix handling for spurious interrupts not being mapped to any IRQs.
Currently, spurious interrupts that are not mapped to any IRQs are
handled as IRQ 15 (== IA64_SPURIOUS_VECTOR). But it is not proper
because vector != irq. We need special handlings for such spurious
interrupts not being mapped to any IRQs.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Make flush_tlb_kernel_range() an inline function.
[SERIAL]: Fix 32-bit warnings in sunzilog.c and sunsu.c
[SPARC32]: Kill unused vars and macros from prom/console.c
[SPARC32]: Add __cmpdi2() libcall implementation ala. MIPS.
[VIDEO]: Do not prom_halt() in cg3 and bw2 device probe.
[SUNVDC]: Use slice 0xff on VD_DISK_TYPE_DISK.
This patch removes one of the two linux/console.h included in
arch/xtensa/platform-iss/console.c
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
Add support for processors that have cache-aliasing issues, such as
the Stretch S5000 processor. Cache-aliasing means that the size of
the cache (for one way) is larger than the page size, thus, a page
can end up in several places in cache depending on the virtual to
physical translation. The method used here is to map a user page
temporarily through the auto-refill way 0 and of of the DTLB.
We probably will want to revisit this issue and use a better
approach with kmap/kunmap.
Signed-off-by: Chris Zankel <chris@zankel.net>
Newer processor versions starting with Xtensa6/LX2 support an 'executable'
bit for memory pages. This bit replaces the 'valid' bit, so it must be
always set to one for older processor versions. To mark a page invalid, we now
set the cache-attributes to b11, which is backward compatible.
Signed-off-by: Chris Zankel <chris@zankel.net>
Xtensa passes long long arguments in a even/odd register pair,
so we also need to shuffle the arguments when passed through the
system call to avoid an empty argument register.
Signed-off-by: Chris Zankel <chris@zankel.net>
The string-io functions (outs{bwl}, ins{bwl}) are independent from
the PCI option and should be in a separate file.
Signed-off-by: Chris Zankel <chris@zankel.net>
A variable was defined with __init instead of __initdata and
the function accessing that variable wasn't initialized with
__init.
Signed-off-by: Chris Zankel <chris@zankel.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix SLB initialization at boot time
[POWERPC] Fix undefined reference to device_power_up/resume
[POWERPC] cell: Update cell_defconfig for 2.6.23
[POWERPC] axonram: Do not delete gendisks queue in error path
[POWERPC] axonram: Module modification for latest firmware API changes
[POWERPC] cell: Support pinhole-reset on IBM cell blades
[POWERPC] spu_manage: Use newer physical-id attribute
[POWERPC] pasemi: Another IOMMU bugfix for 64K PAGE_SIZE
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] Add NOTES section
[PARISC] Use compat_sys_getdents
[PARISC] Do not allow STI_CONSOLE to be modular
[PARISC] Clean up sti_flush
[PARISC] Add dummy isa_(bus|virt)_to_(virt|bus) inlines
[PARISC] Add empty <asm-parisc/vga.h>
Bisected bizarre kernel-space nullptr dereference in udev to commit
18991197b4, adding the NOTES section fixes
it.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
shutdown_bridge_irq disconnects the irq so we need to connect the irq or
requesting the same irq a send time will fail. This used to make
things like ifconfig eth0 down; ifconfig eth0 up fail on IP27.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Certain 32-bit kernel configurations seem to be able to cause references,
this was observed with gcc 4.1.2.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d several callers of
pcibios_resource_to_bus are no longer marked __devinit resulting in a
pile of modpost warnings if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x15dde8): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_map_rom' and 'pci_map_rom_copy')
WARNING: vmlinux.o(.text+0x15e140): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_update_resource' and 'pci_claim_resource')
WARNING: vmlinux.o(.text+0x15f0cc): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f0f0): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f114): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f138): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_setup_cardbus' and 'pci_bus_assign_resources')
WARNING: vmlinux.o(.text+0x15f438): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
WARNING: vmlinux.o(.text+0x15f4f4): Section mismatch: reference to .init.text:pcibios_resource_to_bus (between 'pci_bus_assign_resources' and 'pbus_size_mem')
Removing __devinit from pcibios_resource_to_bus make the same necessary
for pcibios_fixup_device_resources as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 96bde06a2d pcibios_fixup_bus's caller
pci_scan_child_bus is no longer marked __devinit resulting in this modpost
warning if PCI && !HOTPLUG:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x158b9c): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The appended patch adds code to update siginfo_t's si_code field. It
fixes e.g. a floating point overflow regression in the SBCL testsuite.
Signed-off-By: Thiemo Seufer <ths@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also removes the while(1); loop by propagating the ATTRIB_NORET of die()
to nmi_exception_handler.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The rtc-rs5c348 SPI driver name doesn't match its module name, which
prevents it from properly hotplugging. There is only one in-tree user
of its driver, which is fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/basler/excite/excite_prom.o
arch/mips/basler/excite/excite_prom.c:136:3: #error 64 bit support not implemented
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS doesn't do CPU hotplugging yet but since many of the functions don't
even have an __init let's fix this right.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leaving these sections is useful to some tools that look at the image, and
none of them are loaded into memory. The .mdebug.abi64 section, in
particular, lets GDB recognize vmlinux.32 as an N64 program instead of
guessing that it is O32.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is needed since the Sibyte serial driver was exchanged.
Issue report by Imre Kaloz <kaloz@openwrt.org>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (30 commits)
ACPI: work around duplicate name "VID" problem on T61
acpiphp_ibm: add missing '\n' to error message
ACPI: add dump_stack() to trace acpi_format_exception programming errors
make drivers/acpi/scan.c:create_modalias() static
ACPI: Fix a warning of discarding qualifiers from pointer target type
ACPI: "ACPI handle has no context!" should be KERN_DEBUG
ACPI video hotkey: export missing ACPI video hotkey events via input layer
ACPI: Validate XSDT, use RSDT if XSDT fails
ACPI: /proc/acpi/thermal_zone trip points are now read-only, mark them as such
ACPI: fix ia64 allnoconfig build
PNP: remove null pointer checks
PNP: remove MODULE infrastructure
ISAPNP: removed unused isapnp_detected and ISAPNP_DEBUG
PNPACPI: remove unnecessary casts of "void *"
PNPACPI: simplify irq_flags()
PNP: fix up after Lindent
ACPI: enable GPEs before calling _WAK on resume
asus-laptop: Fix rmmod of asus_laptop
sony-laptop: call sonypi_compat_init earlier
sony-laptop: enable Vaio FZ events
...
This partially reverts edd0622bd2.
It turns out that the part of that commit that aimed to ensure that we
created an SLB entry for the kernel stack on secondary CPUs when
starting the CPU didn't achieve its aim, and in fact caused a
regression, because get_paca()->kstack is not initialized at the point
where slb_initialize is called.
This therefore just reverts that part of that commit, while keeping
the change to slb_flush_and_rebolt, which is correct and necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
On exit do not delete gendisk's queue because this is already done by
del_gendisk(). Doing it twice may cause memory damage.
Signed-off-by: Maximilian <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Firmware would not deliver two interrupt numbers in device-tree any more
but only one, for correctable ECC, because uncorrectable ECC from now
is handled by firmware itself.
Changes in the axonram module are necessary because in the old version, if
it is not allowed to fetch the second interrupt number from device-tree,
it interpretes this as an error case and exits.
Signed-off-by: Maximilian <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell Broadband Engine has a method of injecting a
system-reset-exception from an external source into the
operating system, which should trigger the regular behaviour
of entering xmon or kdump.
Unfortunately, the exception handler cannot distinguish it from
other interrupt causes by the SRR1 register, which gets used
for this on Power 6 and others.
IBM Blade servers that want to support triggering the
system reset exception using a pinhole button in the front
panel therefore use an extra register to determine the
reset cause.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
Legacy device tree used the reg property for the physical id of an
spe. On newer device tree layouts the reg property contains the
"correct" value in the reg attribute. So there has been intoduced the
"physical-id" on newer devicetree layouts. The id is stored by
spu_manage into the spu struct as spe_id. cbe_thermal has been
changed to use the spu->spe_id. There's no need for the thermal code
to check devicetree attributes for itself.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More fallout from the switch from PAGE_SIZE based IOMMU to the native page
size for the driver. By pure luck it happened to work most of the time, since
we end up invalidating the wrong entries in the TLB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[x86 setup] Make sure AH=00h when setting a video mode
[x86 setup] Volatilize asm() statements
Include linux/fs.h to get the prototype for do_pipe().
Build fix.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include linux/fs.h to get the prototype for getname().
Build fix.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Passing a u8 into a register doesn't mean gcc will zero-extend it.
Also, don't depend on thhe register not to change.
Per bug report from Saul Tamari.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
asm() statements need to be volatile when:
a. They have side effects (other than value returned).
b. When the value returned can vary over time.
c. When they have ordering constraints that cannot be expressed to gcc.
In particular, the keyboard and timer reads were violating constraint (b),
which resulted in the keyboard/timeout poll getting
loop-invariant-removed when compiling with gcc 4.2.0.
Thanks to an anonymous bug reporter for pointing this out.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
construct a more or less wall-clock time out of sched_clock(), by
using ACPI-idle's existing knowledge about how much time we spent
idling. This allows the rq clock to work around TSC-stops-in-C2,
TSC-gets-corrupted-in-C3 type of problems.
( Besides the scheduler's statistics this also benefits blktrace and
printk-timestamps as well. )
Furthermore, the precise before-C2/C3-sleep and after-C2/C3-wakeup
callbacks allow the scheduler to get out the most of the period where
the CPU has a reliable TSC. This results in slightly more precise
task statistics.
the ACPI bits were acked by Len.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Len Brown <len.brown@intel.com>
The pins for GPIO should be provided as plain number
build as (GPIO_PORTx + pin_number). But to setup
the output GPIO_GIUS and GPIO_DR have to be specified
in mode to route right value to the pin.
This is a fix, it should go to 2.6.23
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We no longer have any dependancies on include/asm-ppc so we can get ride
of the makefile hacks to include it in the build process.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To build arch/powerpc without including asm-ppc/ we need these files
in asm-powerpc/
Moved some headers under arch/powerpc/platforms if they were only used by
platform or driver files and fixed up the source file includes to match
the new locations
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove includes of files that existed in arch/ppc that we dont need in
arch/powerpc anymore. The following includes were removed:
<asm/amigappc.h>
<asm/bootinfo.h>
<asm/ppcboot.h>
<asm/ppc_sys.h>
<asm/residual.h>
<asm/m8260_pci.h>
This also caused platforms/embedded6xx/mpc7448_hpc2.h to no longer be
needed and thus removed.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Xen i386 xen-head.S fix sections mixup
xen-head.S does not come back to the data section, leaving the text section
as current section. It causes problems with a slightly enhanced DEBUG_RODATA
that supports CONFIG_HOTPLUG and bringing a CPU up after the text has been
marked read-only: reference to early_gdt_descr causes a page fault.
Updates:
- It should be using pushsection/popsection.
- Actually, the push/popsections around the ELFNOTEs are redundant; ELFNOTE()
does its own push/popsection to put things into the appropriate .note* section
anyway.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch which limited the number of sectors in a single request
to a COWed device was correct in concept, but the limit was implemented in
the wrong place.
By putting it in ubd_add, it covered the cases where the COWing was
specified on the command line. However, when the command line only has the
COW file specified, the fact that it's a COW file isn't known until it's
opened, so the limit is missed in these cases.
This patch moves the sector limit from ubd_add to ubd_open_dev.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't include RODATA into text segment as it includes the kallsyms data and
can cause spurious link failures (layout differences can change the number of
symbols in kallsyms, i.e. when a symbol is equal to _etext it's not
included).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Revert f642b26380.
[SPARC64]: Need to clobber global reg vars in switch_to().
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Change atomic_read/set to inline functions with barrier semantics.
[S390] kprobes: fix instruction length calculation
[S390] hypfs: inode corruption due to missing locking
[S390] disassembler: fix b2 opcodes like srst, bsg, and others
[S390] vmur: fix reference counting for vmur device structure
[S390] vmur: fix diag14 exceptions with addresses > 2GB.
[S390] qdio: Refresh buffer states for IQDIO Asynchronous output queue
[S390] qdio: fix EQBS handling on CCQ96
[S390] cio: change confusing message in cmf.
[S390] cio: dont forget to set last slot to NULL in ccw_uevent().
Touching vmalloc memory in the middle of a lazy mode update can generate
a kernel PDE update, which must be flushed immediately. The fix is to
leave lazy mode when doing a vmalloc sync.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Placing a kprobe on "bc" instruction (s390/s390x) can cause an oops.
The instruction length is encoded into the first two bits of the s390
instruction. Kprobe is incorrectly computing the instruction length.
The instruction length is used for determining what type of "fix-up" is
needed for conditional branch instruction. The problem can bee seen by
placing a kprobe on a "bc" instruction that will not branch. The
results is that Kprobe incorrectly computes the new instruction
pointer (psw.addr) after single stepping the instruction. The problem
is corrected with this patch.
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
hypfs removes the whole hypfs directory tree and creates a new one, when a
process triggers an update by writing to the "update" attribute. When removing
and creating files, it is necessary to lock the inode of the parent directory
where the files live. Currently hypfs does not lock the parent inode, which
can lead to inode corruption. This patch:
* Introduces correct locking
* Fixes i_nlink reference counting for inodes, when creating directories
* Adds info printk, when hypfs filesystem has been mounted
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The instruction table for b2 opcodes was missing an opfrag value
for the cpya instruction. All instructions specified after cpya
were not considered by the disassembler. The fix is simple and
obvious - add the opfrag field to the cpya instruction.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The APLLs are most efficiently idled by hardware.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bugfixes for the OSK led support:
- Fix Kconfig merge glitches: Mistral handles idle and timer leds just fine
- Fix pm_suspend() runtime botch: can't sleep, so can't touch tps65010 leds
Improvements:
- Switch sense of Mistral idle led, so idle == off
Probably the TPS65010 leds should be handled only by the "new led" API.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning. It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
out of head_64.S and into platforms/iseries/exception.S
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It makes head_64.S a bit more readable and will allow us to move the
iSeries exceptions elsewhere.
This also removes the last line of the comment:
* The following macros define the code that appears as
* the prologue to each of the exception handlers. They
* are split into two parts to allow a single kernel binary
* to be used for pSeries and iSeries.
* LOL. One day... - paulus
Anything is possible. :-)
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework timebase handoff to play nice with configurations with more than
2 cores, as well as with CPU hotplug.
Previous scheme just pushed out the current timebase from the giving
core to all cores without caring if they wanted it or not, nor checking
if they'd taken it. The taking side didn't make sure the giving side
had provided a value yet either. In other words, it was completely broken.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows booting on legacy, non-device-tree aware versions of U-boot.
It also fixes up the hardware to match the PCI and chipselect information
in the device tree, as u-boot is inconsistent in setting these up
correctly (or at all).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows booting on legacy, non-device-tree aware versions of U-boot.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Most of these were previously used by numerous C files and
redeclared in each one.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This serial port is used on all 8xx, many 82xx, and some 85xx chips.
The driver requires that the port has already been set up by the firmware
and/or platform code.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
1. Search the entire compatible list for serial devices.
The serial code previously did a simple strcmp on the compatible
node; this fails when the match string is not the first compatible
listed. Use dt_is_compatible() instead.
2. Don't call serial_edit_cmdline if getc isn't defined.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
U-boots more recent than when ppcboot.h was forked allow the board config
file to enable additional ethernet ports explicitly, rather than
using a hardcoded list of targets. This allows bootwrapper platform
files to do the same.
Fortunately, nothing after the ethernet addresses is of interest to
cuboot platforms, so the inevitable mismatches won't be too catastrophic.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also, include types.h from io.h, so callers don't have to.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This can be used rather than doing a simple strcmp, which will fail to
handle multiple compatible entries.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
1. The check whether ranges fits in the buffer was using elements rather
than bytes.
2. Empty ranges were not properly treated as transparent, and missing
ranges were treated as transparent.
3. The loop terminated when translating from the root rather than to. Once
bug #2 was fixed, it failed due to a missing ranges in the root node.
4. In decoding the ranges property, the #size-cells used was that of
the parent, not the child.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This lets udelay() work properly on platforms which use dt_fixup_cpu_clocks.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
All cuImage types are ignored, as well as preprocessed .lds files,
and the forthcoming zImage.bin files and embedded planet board images.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to have xLparMap in head_64.S so that it is at a fixed address
(because the linker will not resolve (address & 0xffffffff) for us).
But the assembler miscalculates the KERNEL_VSID() expressions. So put
the confusing expressions into asm-offsets.c.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The built-in IDE controller is configured in legacy mode, but the PCI
registers advertise native mode. Force the PCI class into legacy
mode. This allows pata_via to access two drives.
The Pegasos specific irq enforcement in the via82cxxx driver must stay
because there is apparently no generic way to setup irq per channel.
Tested on Pegasos2 with firmware version 20040810, and two IDE disks.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a plat_irq_setup() symbol for sh4-202. Without
this fix it is impossible to build a working kernel using the
microdev_defconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The initial user manuals for MPC8544/8533 had some issues with properly
documenting the device IDs for MPC8544/8533. These processors are almost
identical and both show up on the reference boards.
Fix up the quirks for PCIe support to handle MPC8533/E.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I did some testing and found quite a lot of problems (doesn't
boot at all on non NUMA and misassigns cores on Opteron systems).
Mark it as experimental and warn against its use for now.
It's still default y for SUMMIT/NUMAQ because it'll presumably
work on these systems.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Older versions of binutils do not support -Wa,-isa= tuning, which is
something we rely on for enabling DSP opcode support on the newer
parts. SH3-DSP parts can still be handled with -Wa,-dsp even if the
newer parts require the newer versions of binutils for supporting the
new opcodes.
This was broken in -rc1 when the SH4AL-DSP support was being reworked,
and is needed to get SH3-DSP working with older toolchains again.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This causes boot failures for some people.
It looks like in fact that some SILO provided
ramdisk images should not be KERNBASE normalized.
Signed-off-by: David S. Miller <davem@davemloft.net>
In MPS mode, "nosmp" and "maxcpus=0" boot a UP kernel with IOAPIC disabled.
However, in ACPI mode, these parameters didn't completely disable
the IO APIC initialization code and boot failed.
init/main.c:
Disable the IO_APIC if "nosmp" or "maxcpus=0"
undefine disable_ioapic_setup() when it doesn't apply.
i386:
delete ioapic_setup(), it was a duplicate of parse_noapic()
delete undefinition of disable_ioapic_setup()
x86_64:
rename disable_ioapic_setup() to parse_noapic() to match i386
define disable_ioapic_setup() in header to match i386
http://bugzilla.kernel.org/show_bug.cgi?id=1641
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some host drivers depend on CONFIG_IDE_GENERIC to do the probing but their
config options lack explicit dependencies on IDE_GENERIC. In the long-term
these host drivers should be fixed to do the probing themselves but for now
fix them by making their config options select CONFIG_IDE_GENERIC.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add a bootwrapper for the AMCC 440EP Bamboo Eval board. This also adds a
common fixup_clock function for all 440EP(x) chips.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Remove inclusion of __res on 40x. We don't need it in arch/powerpc
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Allow generic_calibrate_decr to work for 40x platforms. Given that the hardware
behavior is identical, this also changes the set_dec function to reload the PIT
on 40x to match the behavior 44x currently has.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add MMU definitions for 40x platforms. Also fixes two warnings in 40x_mmu.c.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Make the fixup_memsize function common for all of 4xx as several chips share
the same SDRAM controller. Also add functions to reset 40x chips and quiesce
the ethernet.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Rename the 44x.c wrapper file to 4xx.c. This will allow us to add common
functions in a single file that can be shared across all of 4xx.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Remove some leftover cruft in the 40x Kconfig file. Also make sure we
select WANT_DEVICE_TREE for 40x.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
4xx is a bit of a misnomer for certain things, as they really apply to PowerPC
40x only. Rename some of the files to clean this up.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
With commit ab144f5ec6 the patching code
now collects the complete new instruction stream into a temp buffer
before finally patching in the new insns. In some cases the paravirt
patchers will choose to leave the patch site unpatched (length mismatch,
clobbers mismatch, etc).
This causes the new patching code to copy an uninitialized temp buffer,
i.e. garbage, to the callsite. Simply make sure to always initialize
the buffer with the original instruction stream. A better fix is to
audit all the patchers and return proper length so that apply_paravirt()
can skip copies when we leave the patch site untouched.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Very old 64bit binutils have .cfi_startproc/endproc, but
no .cfi_rel_offset. Check for .cfi_rel_offset too.
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Very old binutils (2.12.90...) seem to have trouble with newlines
in assembler macro invocation. They put them into the resulting
argument expansion. In this case this lead to a parse error because
a .rept expression ended up spread over multiple lines. Change the PMDS()
invocation to a single line.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed wrong expression which enabled watchdogs even if nmi_watchdog kernel
parameter wasn't set. This regression got slightly introduced with commit
b7471c6da9.
Introduced NMI_DISABLED (-1) which allows to switch the value of NMI_DEFAULT
without breaking the APIC NMI watchdog code (again).
Fixes:
https://bugzilla.novell.com/show_bug.cgi?id=298084http://bugzilla.kernel.org/show_bug.cgi?id=7839
And likely some more nmi_watchdog=0 related issues.
Signed-off-by: Daniel Gollub <dgollub@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This should fix an oops with PCMCIA PATA devices
http://bugzilla.kernel.org/show_bug.cgi?id=8424
This is not a full fix for the problem, but probably
still the right thing to do.
[ I'm almost certain it's *not* the right thing to do, but it avoids an
oops, and I want comments from others on what the right thing would
actually be.. I suspect we should just remove the use of dma_mask
entirely in this function, and just use coherent_dma_mask. - Linus ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
Cross-compilation between e.g. i386 -> 64bit could break -> work around it
[IA64] Enable early console for Ski simulator
[IA64] forbid ptrace changes psr.ri to 3
[IA64] Failure to grow RBS
[IA64] Fix processor_get_freq
[IA64] SGI Altix : fix a force_interrupt bug on altix
[IA64] Update arch/ia64/configs/* s/SLAB/SLUB/
[IA64] get back PT_IA_64_UNWIND program header
[IA64] need NOTES in vmlinux.lds.S
[IA64] make unwinder stop at last frame of the bootloader
[IA64] Clean up CPE handler registration
[IA64] Include Kconfig.preempt
[IA64] SN2 needs platform specific irq_to_vector() function.
[IA64] Use atomic64_read to read an atomic64_t.
[IA64] disable irq's and check need_resched before safe_halt
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[MATH-EMU]: Fix underflow exception reporting.
[SPARC64]: Create a HWCAP_SPARC_N2 and report it to userspace on Niagara-2.
[SPARC64]: SMP trampoline needs to avoid %tick_cmpr on sun4v too.
[SPARC64]: Do not touch %tick_cmpr on sun4v cpus.
[SPARC64]: Niagara-2 optimized copies.
[SPARC64]: Allow userspace to get at the machine description.
[SPARC32]: Remove superfluous 'kernel_end' alignment on sun4c.
[SPARC32]: Fix bogus ramdisk image location check.
[SPARC32]: Remove iommu from struct sbus_bus and use archdata like sparc64.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix invalid semicolon after if statement
[POWERPC] ps3: Fix no storage devices found
[POWERPC] Fix for assembler -g
[POWERPC] Fix small race in 44x tlbie function
[POWERPC] Remove unused code causing a compile warning
[POWERPC] cell: Fix errno for modular spufs_create with invalid neighbour
When using Ski to debug early startup, it's a bit of a pain not to
have printk.
This patch enables the simulated console very early.
It may be worth conditionalising on the command line... but this is
enough for now.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The "ri" field in the processor status register only has defined
values of 0, 1, 2. Do not let ptrace set this to 3. As with
other reserved fields in registers we silently discard the value.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
CC arch/powerpc/sysdev/commproc.o
arch/powerpc/sysdev/fsl_soc.c: In function fsl_pcmcia_of_init:
arch/powerpc/sysdev/fsl_soc.c:1109: error: implicit declaration of function of_platform_device_create
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reserved MCSR bits on FSL BookE parts may have spurious values
when mcheck occurs. Mask these off when printing the MCSR to
avoid confusion. Also, get rid of the MCSR_GL_CI bit defined
for e500 - this bit doesn't actually have any meaning.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupt routing in the device trees for the ULI M1575 was
inproperly using the interrupt line field as pci function. Fixed
up the device tree's to actual conform for to specification and
changed the interrupt mapping code so it just uses a static mapping
setup as follows:
PIRQA - IRQ9
PIRQB - IRQ10
PIRQC - IRQ11
PIRQD - IRQ12
USB 1.1 OCHI (1c.0) - IRQ12
USB 1.1 OCHI (1c.1) - IRQ9
USB 1.1 OCHI (1c.2) - IRQ10
USB 1.1 ECHI (1c.3) - IRQ11
LAN (1b.0) - IRQ6
AC97 (1d.0) - IRQ6
Modem (1d.1) - IRQ6
HD Audio (1d.2) - IRQ6
SATA (1f.1) - IRQ5
SMB (1e.1) - IRQ7
PMU (1e.2) - IRQ7
PATA (1f.0) - IRQ14/15
Took the oppurtunity to refactor the code into a single file so we
don't have to duplicate these fixes on the two current boards in the
tree and several forth coming boards that will also need the code.
Fixed RTC support that requires a dummy memory read on the P2P bridge
to unlock the RTC and setup the default of the RTC alarm registers to
match with a basic x86 style CMOS RTC.
Moved code that poked ISA registers to a FIXUP_FINAL quirk to ensure
the PCI IO space has been setup properly before we start poking ISA
registers at random locations.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RTC CMOS driver expects the interrupt to be a resource of the platform
device. Use a fixed interrupt value of 8 since on PPC if we are using this
its off an i8259 which we ensure has interrupt numbers 0..15.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use strlcpy() to guarantee strings in i2c device type and driver_name
fields are 0-terminated.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These functions are only called by __init functions.
WARNING: vmlinux.o(.text+0x56aa0): Section mismatch: reference to .init.text:.lmb_alloc (between '.iob_init' and '.iommu_init_early_pasemi')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The functions are only called from __init functions.
WARNING: vmlinux.o(.text+0x45ed0): Section mismatch: reference to .init.text:.btext_find_display (between '.udbg_adb_init_early' and '.udbg_adb_init')
WARNING: vmlinux.o(.text+0x45f9c): Section mismatch: reference to .init.text:.btext_find_display (between '.udbg_adb_init' and '.udbg_adb_getc_poll')
WARNING: vmlinux.o(.text+0x46000): Section mismatch: reference to .init.text:.find_via_pmu (between '.udbg_adb_init' and '.udbg_adb_getc_poll')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These functions are only called from __init functions.
WARNING: vmlinux.o(.text+0x398f4): Section mismatch: reference to .init.text:.lmb_alloc (between '.iommu_init_early_dart' and '.pci_dma_bus_setup_dart')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x23258): Section mismatch: reference to .init.text:.lmb_reserve (between '.reserve_kdump_trampoline' and '.restore_processor_state')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present the cascade interrupt handler for the UIC (interrupt
controller on 4xx embedded chips) will misbehave badly if it is called
spuriously - that is if the handler is invoked when no interrupts are
asserted in the child UIC.
Although spurious interrupts shouldn't happen, it's good to behave
robustly if they do. This patch does so by checking for and ignoring
spurious interrupts.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present the driver for the UIC (the embedded interrupt controller
in 4xx chips) uses the handle_level_irq() flow handler. It turns out
this does not correctly handle level triggered interrupts on the UIC.
Specifically, acknowledging an irq on the UIC (i.e. clearing the
relevant bit in UIC_SR) will have no effect for a level interrupt
which is still asserted by the external device, even if the irq is
already masked. Therefore, unlike handle_level_irq() we must ack the
interrupt after invoking the ISR (which should cause the device to
stop asserting the irq) instead of acking it when we mask it, before
the ISR.
This patch implements this change, in a new handle_uic_irq(), a
customised irq flow handler for the UIC. For edge triggered
interrupts, handle_uic_irq() still uses the old flow - we must ack
edge triggered interrupt before the ISR not after, or we could miss a
second event which occurred between invoking the ISR and acking the
irq.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The UIC (interrupt controller in 4xx embedded CPUs) driver currently
missets the IRQ_lEVEL flag in desc->status, due to a thinko. This
patch fixes the bug.
Currently this is only a cosmetic problem (affects the output in
/proc/interrupts), however subsequent patches will use the IRQ_LEVEL
flag to affect flow handling.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes some of the #ifdefs from .c files.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/mm/mmu_context_64.c: In function 'init_new_context':
arch/powerpc/mm/mmu_context_64.c:31: warning: unused variable 'new_context'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to handle alignment traps generated by the following
new floating-point load/store instructions, by emulating the
instruction in the kernel (as is done for other instructions that
generate alignment traps):
lfiwax load floating-point as integer word algebraic indexed
stfiwx store floating-point as integer word indexed
lfdp load floating-point double pair
lfdpx load floating-point double pair indexed
stfdp store floating-point double pair
stfdpx store floating-point double pair indexed
All these except stfiwx are new in POWER6.
lfdp/lfdpx/stfdp/stfdpx load and store 16 bytes of memory into an
even/odd FP register pair. In little-endian mode each 8-byte value is
byte-reversed separately (i.e. not as a 16-byte unit). lfiwax/stfiwx
load or store the lower 4 bytes of a floating-point register from/to
memory; lfiwax sets the upper 4 bytes of the FP register to the sign
extension of the value loaded.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove dead code, and a misleading comment about EEH checking
for video devices. The removed code is a left-over from the
olden days where there was concern over how video devices
worked in Linux. We are never going to go that way again,
so kill this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 17 -----------------
1 file changed, 17 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powermac pci configuration space write methods read the written
location immediately after the write is performed, presumably in order
to flush the write. However, configuration space writes are not
allowed to be posted, making these reads gratuitous. Furthermore,
this behavior potentially causes us to violate the PCI PM spec when
changing between e.g. D0 and D3 states, because a delay of up to 10ms
may be required before the OS accesses configuration space after the
write which initiates the transition.
Remove the unnecessary reads from macrisc_write_config,
u3_ht_write_config, and u4_pcie_write_config.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pasemi pci configuration space write method reads the written
location immediately after the write is performed, presumably in order
to flush the write. However, configuration space writes are not
allowed to be posted, making these reads gratuitous. Furthermore,
this behavior potentially causes us to violate the PCI PM spec when
changing between e.g. D0 and D3 states, because a delay of up to 10ms
may be required before the OS accesses configuration space after the
write which initiates the transition.
Remove the unnecessary reads from pa_pxp_write_config.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The maple PCI configuration space write methods read the written
location immediately after the write is performed, presumably in order
to flush the write. However, configuration space writes are not
allowed to be posted, making these reads gratuitous. Furthermore,
this behavior potentially causes us to violate the PCI PM spec when
changing between e.g. D0 and D3 states, because a delay of up to 10ms
may be required before the OS accesses configuration space after the
write which initiates the transition. It definitely causes a system
hang for me with a Broadcom 5721 PCIE network adapter, which is fixed
by this change.
Therefore this removes the gratuitous reads from u3_agp_write_config,
u3_ht_write_config, and u4_pcie_write_config.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order to compile drivers as modules that uses some of the
DCR functions, we need to export the symbols. Example, EMAC
driver and other drivers that are under development use these
functions.
Signed-off-by: Murali Iyer <mniyer@us.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Eliminate the use of error_log_cnt as a global var shared across
different directories. Pass it as a parameter instead.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
Respin of earlier patch, with the CONFIG_PSERIES junk removed from the
header file.
arch/powerpc/kernel/nvram_64.c | 10 +++++-----
arch/powerpc/platforms/pseries/rtasd.c | 7 ++++---
include/asm-powerpc/nvram.h | 6 ++++--
3 files changed, 13 insertions(+), 10 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Get rid of the jumbled usage of the no_logging flag. Its use
spans several directories, and is incorrectly/misleadingly
documented. Instead, two changes:
1) nvram will accept error log as soon as its ready.
2) logging to nvram stops on the first fatal error reported.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/kernel/nvram_64.c | 8 --------
arch/powerpc/platforms/pseries/rtasd.c | 14 ++++++--------
2 files changed, 6 insertions(+), 16 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Josh Boyer
Valentine Barshak
Hirokazu Takata
Christian Ehrhardt
Linus Torvalds
Peter Chubb
Peter Chubb
Prarit Bhargava
John Keller
Jesper Juhl
Linus Torvalds
H. Peter Anvin
David Gibson
Rafael J. Wysocki
Atsushi Nemoto
Jeff Dike
David S. Miller
Adrian Bunk
Masakazu Mokuno
Pavel Pisa
Paul Mackerras
Andre Detsch
Arnd Bergmann
Christian Krafft
Kumar Gala
Kenji Kaneshige
Samuel
Frederik Deweerdt
Chris Zankel
Kyle McMartin
Ralf Baechle
Thiemo Seufer
Nicolas Schichan
Ilpo Järvinen
Yoichi Yuasa
Ralf Baechle
Daniel Jacobowitz
Russell King
Arnd Bergmann
Maxim Shchetynin
Olof Johansson
Len Brown
Greg Ungerer
Ingo Molnar
Mathieu Desnoyers
Roman Zippel
Geert Uytterhoeven
Yoshinori Sato
Zachary Amsden
David Wilder
Michael Holzheu
Christian Borntraeger
Juha Yrjola
Dirk Behme
David Brownell
Kevin Hilman
Stephen Rothwell
Scott Wood
Olaf Hering
Magnus Damm
Andi Kleen
Paul Mundt
Bartlomiej Zolnierkiewicz
Chris Wright
Daniel Gollub
Jan Engelhardt
Shaohua Li
Becky Bruce
Guennadi Liakhovetski
Linas Vepstas
Nathan Lynch
Murali Iyer