The SH2 version of entry.S uses global variables, which need to be
cpu-local in order to work with SMP. For ease of access from asm,
simply use arrays indexed by cpu number, and require the availability
of an address (mmio register or properly setup per-cpu memory) from
which the current cpu's index can be read.
Signed-off-by: Rich Felker <dalias@libc.org>
The version of futex.h in asm-generic should really be adapted to do
the same thing so that this hideous code does not have to be
duplicated per-arch.
Signed-off-by: Rich Felker <dalias@libc.org>
The J-Core cpu has, as an ISA extension, an atomic compare-and-swap
instruction cas.l which applications need to use (instead the imask or
gusa atomic models, which are fundamentally limited to UP) for
synchronization in order to be compatible with SMP systems. Provide a
hwcap flag so that it's possible to do runtime selection and support
both.
Signed-off-by: Rich Felker <dalias@libc.org>
At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.
Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.
No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.
Signed-off-by: Rich Felker <dalias@libc.org>
Such a configuration could only be selected by manually selecting
CONFIG_OF; SH_DEVICE_TREE selects both. The affected code is using the
flat DTB at boot time and thus rightfully should depend on
OF_FLATTREE, not just OF.
Signed-off-by: Rich Felker <dalias@libc.org>
There is no arch-specific sched_clock implementation for sh, resulting
in use of the old default jiffies-based implementation. Instead, use
the modern generic sched_clock framework so that drivers can register
better backends.
Signed-off-by: Rich Felker <dalias@libc.org>
The Kconfig for this driver is currently:
config HEARTBEAT
bool "Heartbeat LED"
....meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The Kconfig currently controlling compilation of this code is:
config SH_SECUREEDGE5410
bool "SecureEdge5410"
....meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The Makefile/Kconfig currently controlling compilation of this code is:
obj-$(CONFIG_DEBUG_FS) += $(debugfs-y)
debugfs-y := asids-debugfs.o
lib/Kconfig.debug:config DEBUG_FS
lib/Kconfig.debug: bool "Debug Filesystem"
....meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular code, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The Makefile currently controlling compilation of this code is:
obj-y := debugtraps.o dma-nommu.o dumpstack.o \
[...]
syscalls_$(BITS).o time.o topology.o traps.o \
traps_$(BITS).o unwinder.o
....meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular code, so that when reading
the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The futex cmpxchg runtime testing in kernel/futex.c depends on
accesses to address 0 producing EFAULT, which obviously does not work
on nommu. Since SH always has cmpxchg, disable the broken runtime
detection.
At some point this should be fixed at the kernel/futex.c level. UP
machines can always provide a working cmpxchg with interrupt masking,
and SMP cannot function without a working cmpxchg anyway.
Signed-off-by: Rich Felker <dalias@libc.org>
SH3/4 (with MMU) have a virtually indexed cache, requiring explicit
work to avoid consistency problems arising from having the same
physical address range cached in multiple cache lines. This is
unneeded for the NOMMU case, and some of the resulting code paths
(kmap_coherent) don't work. SH2 only avoided this problem by having a
4-way associative cache with way size equal to the page size (4k),
yielding no cache index bits outside of the page offset and thus no
aliases.
Signed-off-by: Rich Felker <dalias@libc.org>
Up until now, the SH version of the sigcontext structure, and thus
mcontext_t/ucontext_t, varied depending on the cpu model the kernel
was built to run on. SH-4 (including SH-4A) and SH-2A used the form
with space for FPU registers, and everything else used a form that
omitted them.
From a userspace perspective, however, the structure layout must be
fixed for a given ABI. Traditionally glibc and uClibc used the form
with space for FPU registers only when __SH4__ (which implies FPU;
__SH4_NOFPU__ is the predefined macro for SH-4 but with no-FPU ABI)
was defined. As a result:
- SH-4 no-FPU programs never matched kernel sigcontext.
- SH-3 programs did not match kernel sigcontext if run on SH-4,
despite an apparent intent that they be compatible.
- SH-2 and SH-2A programs (using uClibc) did not match kernel
sigcontext if run on SH-2A.
The mismatch might seem inconsequential because it occurs at the end
of the sigcontext structure, but sigcontext is embedded as uc_mcontext
in ucontext_t, where it is followed by uc_sigmask, an important member
for signal handlers to have access to. In particular, access to
uc_sigmask is necessary for a correct implementation of thread
cancellation.
It would be possible to retain support for both sigcontext ABIs via a
personality mechanism, but since many configurations were already
broken and nobody noticed, and since there are very few if any users
of legacy no-FPU models anymore, I have opted to just remove the
variation and always include space for the FPU registers in
sigcontext. This was proposed and discussed on a thread "SH sigcontext
ABI is broken" cross-posted to linux-sh, libc-alpha, and musl libc
lists in June 2015, and no objections were raised.
Signed-off-by: Rich Felker <dalias@libc.org>
Correct bitoff in big endian OS.
Current code works correctly for 1 byte but not for 2 bytes.
Fixes: 3226aad81a ("sh: support 1 and 2 byte xchg")
Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Highlights include:
Stable bugfixes:
- nfs: don't create zero-length requests
- Several LAYOUTGET bugfixes
Features:
- Several performance related features
- More aggressive caching when we can rely on close-to-open cache
consistency
- Remove serialisation of O_DIRECT reads and writes
- Optimise several code paths to not flush to disk unnecessarily. However
allow for the idiosyncracies of pNFS for those layout types that need
to issue a LAYOUTCOMMIT before the metadata can be updated on the server.
- SUNRPC updates to the client data receive path
- pNFS/SCSI support RH/Fedora dm-mpath device nodes
- pNFS files/flexfiles can now use unprivileged ports when the generic NFS
mount options allow it.
Bugfixes:
- Don't use RDMA direct data placement together with data integrity or
privacy security flavours
- Remove the RDMA ALLPHYSICAL memory registration mode as it has potential
security holes.
- Several layout recall fixes to improve NFSv4.1 protocol compliance.
- Fix an Oops in the pNFS files and flexfiles connection setup to the DS
- Allow retry of operations that used a returned delegation stateid
- Don't mark the inode as revalidated if a LAYOUTCOMMIT is outstanding
- Fix writeback races in nfs4_copy_range() and nfs42_proc_deallocate()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WNyE
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.8-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable bugfixes:
- nfs: don't create zero-length requests
- several LAYOUTGET bugfixes
Features:
- several performance related features
- more aggressive caching when we can rely on close-to-open
cache consistency
- remove serialisation of O_DIRECT reads and writes
- optimise several code paths to not flush to disk unnecessarily.
However allow for the idiosyncracies of pNFS for those layout
types that need to issue a LAYOUTCOMMIT before the metadata can
be updated on the server.
- SUNRPC updates to the client data receive path
- pNFS/SCSI support RH/Fedora dm-mpath device nodes
- pNFS files/flexfiles can now use unprivileged ports when
the generic NFS mount options allow it.
Bugfixes:
- Don't use RDMA direct data placement together with data
integrity or privacy security flavours
- Remove the RDMA ALLPHYSICAL memory registration mode as
it has potential security holes.
- Several layout recall fixes to improve NFSv4.1 protocol
compliance.
- Fix an Oops in the pNFS files and flexfiles connection
setup to the DS
- Allow retry of operations that used a returned delegation
stateid
- Don't mark the inode as revalidated if a LAYOUTCOMMIT is
outstanding
- Fix writeback races in nfs4_copy_range() and
nfs42_proc_deallocate()"
* tag 'nfs-for-4.8-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (104 commits)
pNFS: Actively set attributes as invalid if LAYOUTCOMMIT is outstanding
NFSv4: Clean up lookup of SECINFO_NO_NAME
NFSv4.2: Fix warning "variable ‘stateids’ set but not used"
NFSv4: Fix warning "no previous prototype for ‘nfs4_listxattr’"
SUNRPC: Fix a compiler warning in fs/nfs/clnt.c
pNFS: Remove redundant smp_mb() from pnfs_init_lseg()
pNFS: Cleanup - do layout segment initialisation in one place
pNFS: Remove redundant stateid invalidation
pNFS: Remove redundant pnfs_mark_layout_returned_if_empty()
pNFS: Clear the layout metadata if the server changed the layout stateid
pNFS: Cleanup - don't open code pnfs_mark_layout_stateid_invalid()
NFS: pnfs_mark_matching_lsegs_return() should match the layout sequence id
pNFS: Do not set plh_return_seq for non-callback related layoutreturns
pNFS: Ensure layoutreturn acts as a completion for layout callbacks
pNFS: Fix CB_LAYOUTRECALL stateid verification
pNFS: Always update the layout barrier seqid on LAYOUTGET
pNFS: Always update the layout stateid if NFS_LAYOUT_INVALID_STID is set
pNFS: Clear the layout return tracking on layout reinitialisation
pNFS: LAYOUTRETURN should only update the stateid if the layout is valid
nfs: don't create zero-length requests
...
Pull x86 microcode updates from Thomas Gleixner:
- more work to make the microcode loader robust
- a fix for the micro code load precedence
- fixes for initrd loading with randomized memory
- less printk noise on SMP machines
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm, x86/microcode: Add __PAGE_OFFSET_BASE define on 32-bit
x86/microcode/intel: Fix initrd loading with CONFIG_RANDOMIZE_MEMORY=y
x86/microcode: Remove unused symbol exports
x86/microcode/intel: Do not issue microcode updates messages on each CPU
Documentation/microcode: Document some aspects for more clarity
x86/microcode/AMD: Make amd_ucode_patch[] static
x86/microcode/intel: Unexport save_mc_for_early()
x86/microcode/intel: Rename load_microcode_early() to find_microcode_patch()
x86/microcode: Propagate save_microcode_in_initrd() retval
x86/microcode: Get rid of find_cpio_data()'s dummy offset arg
lib/cpio: Make find_cpio_data()'s offset arg optional
x86/microcode: Fix suspend to RAM with builtin microcode
x86/microcode: Fix loading precedence
Pull x86 cpufeature updates from Thomas Gleixner:
- a workaround for the MONITOR instruction erratum of Goldmont CPUs
- small fixes and cleanups here and there
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add workaround for MONITOR instruction erratum on Goldmont based CPUs
x86/cpu: Rename "WESTMERE2" family to "NEHALEM_G"
x86/amd_nb: Clean up init path
x86/cpufeature: Add helper macro for mask check macros
x86/cpufeature: Make sure DISABLED/REQUIRED macros are updated
x86/cpufeature: Update cpufeaure macros
Pull perf fixes from Thomas Gleixner:
"This update contains:
- a fix for the bpf tools to use the new EM_BPF code
- a fix for the module parser of perf to retrieve the
proper text start address
- add str_error_c to libapi to avoid linking against
tools/lib/str_error_r.o"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib api: Add str_error_c to libapi
perf s390: Fix 'start' address of module's map
tools lib bpf: Use official ELF e_machine value
Pull misc fixes from Thomas Gleixner:
"This update contains:
- a fix for stomp-machine so the nmi_watchdog wont trigger on the cpu
waiting for the others to execute the callback
- various fixes and updates to objtool including an resync of the
instruction decoder to match the kernel's decoder"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Un-capitalize "Warning" for out-of-sync instruction decoder
objtool: Resync x86 instruction decoder with the kernel's
objtool: Support new GCC 6 switch jump table pattern
stop_machine: Touch_nmi_watchdog() after MULTI_STOP_PREPARE
objtool: Add 'fixdep' to objtool/.gitignore
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
* Removed CLK_IS_ROOT flag
New clk provider drivers:
* Renesas r8a7796 Clock Pulse Generator / Module Standby and Software
Reset
* Allwinner sun8i H3 Clock Controller Unit
* AmLogic meson8b clock controller (rewritten)
* AmLogic gxbb clock controller
* Support for some new ICs was added by simple changes to static data
tables for chips sharing the same family
Driver updates of note:
* the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with the
DT ABI
-----BEGIN PGP SIGNATURE-----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=1dpY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The bulk of the changes are updates and fixes to existing clk provider
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
- removed CLK_IS_ROOT flag
New clk provider drivers:
- Renesas r8a7796 clock pulse generator / module standby and
software reset
- Allwinner sun8i H3 clock controller unit
- AmLogic meson8b clock controller (rewritten)
- AmLogic gxbb clock controller
- support for some new ICs was added by simple changes to static
data tables for chips sharing the same family
Driver updates of note:
- the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with
the DT ABI"
* tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: Makefile: re-sort and clean up
Revert "clk: gxbb: expose CLKID_MMC_PCLK"
clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver
clk: samsung: make clk-s5pv210-audss explicitly non-modular
clk: exynos5433: remove CLK_IGNORE_UNUSED flag from SPI clocks
clk: oxnas: Add hardware dependencies
clk: imx7d: do not set parent of ethernet time/ref clocks
ARM: dt: sun8i: switch the H3 to the new CCU driver
clk: sunxi-ng: h3: Fix Kconfig symbol typo
clk: sunxi-ng: h3: Fix audio clock divider offset
clk: sunxi-ng: Add H3 clocks
clk: sunxi-ng: Add N-K-M-P factor clock
clk: sunxi-ng: Add N-K-M Factor clock
clk: sunxi-ng: Add N-M-factor clock support
clk: sunxi-ng: Add N-K-factor clock support
clk: sunxi-ng: Add M-P factor clock support
clk: sunxi-ng: Add divider
clk: sunxi-ng: Add phase clock support
clk: sunxi-ng: Add mux clock support
clk: sunxi-ng: Add gate clock support
...
Pull audit updates from Paul Moore:
"Six audit patches for 4.8.
There are a couple of style and minor whitespace tweaks for the logs,
as well as a minor fixup to catch errors on user filter rules, however
the major improvements are a fix to the s390 syscall argument masking
code (reviewed by the nice s390 folks), some consolidation around the
exclude filtering (less code, always a win), and a double-fetch fix
for recording the execve arguments"
* 'stable-4.8' of git://git.infradead.org/users/pcmoore/audit:
audit: fix a double fetch in audit_log_single_execve_arg()
audit: fix whitespace in CWD record
audit: add fields to exclude filter by reusing user filter
s390: ensure that syscall arguments are properly masked on s390
audit: fix some horrible switch statement style crimes
audit: fixup: log on errors from filter user rules
Pull security subsystem updates from James Morris:
"Highlights:
- TPM core and driver updates/fixes
- IPv6 security labeling (CALIPSO)
- Lots of Apparmor fixes
- Seccomp: remove 2-phase API, close hole where ptrace can change
syscall #"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (156 commits)
apparmor: fix SECURITY_APPARMOR_HASH_DEFAULT parameter handling
tpm: Add TPM 2.0 support to the Nuvoton i2c driver (NPCT6xx family)
tpm: Factor out common startup code
tpm: use devm_add_action_or_reset
tpm2_i2c_nuvoton: add irq validity check
tpm: read burstcount from TPM_STS in one 32-bit transaction
tpm: fix byte-order for the value read by tpm2_get_tpm_pt
tpm_tis_core: convert max timeouts from msec to jiffies
apparmor: fix arg_size computation for when setprocattr is null terminated
apparmor: fix oops, validate buffer size in apparmor_setprocattr()
apparmor: do not expose kernel stack
apparmor: fix module parameters can be changed after policy is locked
apparmor: fix oops in profile_unpack() when policy_db is not present
apparmor: don't check for vmalloc_addr if kvzalloc() failed
apparmor: add missing id bounds check on dfa verification
apparmor: allow SYS_CAP_RESOURCE to be sufficient to prlimit another task
apparmor: use list_next_entry instead of list_entry_next
apparmor: fix refcount race when finding a child profile
apparmor: fix ref count leak when profile sha1 hash is read
apparmor: check that xindex is in trans_table bounds
...
Pull userns vfs updates from Eric Biederman:
"This tree contains some very long awaited work on generalizing the
user namespace support for mounting filesystems to include filesystems
with a backing store. The real world target is fuse but the goal is
to update the vfs to allow any filesystem to be supported. This
patchset is based on a lot of code review and testing to approach that
goal.
While looking at what is needed to support the fuse filesystem it
became clear that there were things like xattrs for security modules
that needed special treatment. That the resolution of those concerns
would not be fuse specific. That sorting out these general issues
made most sense at the generic level, where the right people could be
drawn into the conversation, and the issues could be solved for
everyone.
At a high level what this patchset does a couple of simple things:
- Add a user namespace owner (s_user_ns) to struct super_block.
- Teach the vfs to handle filesystem uids and gids not mapping into
to kuids and kgids and being reported as INVALID_UID and
INVALID_GID in vfs data structures.
By assigning a user namespace owner filesystems that are mounted with
only user namespace privilege can be detected. This allows security
modules and the like to know which mounts may not be trusted. This
also allows the set of uids and gids that are communicated to the
filesystem to be capped at the set of kuids and kgids that are in the
owning user namespace of the filesystem.
One of the crazier corner casees this handles is the case of inodes
whose i_uid or i_gid are not mapped into the vfs. Most of the code
simply doesn't care but it is easy to confuse the inode writeback path
so no operation that could cause an inode write-back is permitted for
such inodes (aka only reads are allowed).
This set of changes starts out by cleaning up the code paths involved
in user namespace permirted mounts. Then when things are clean enough
adds code that cleanly sets s_user_ns. Then additional restrictions
are added that are possible now that the filesystem superblock
contains owner information.
These changes should not affect anyone in practice, but there are some
parts of these restrictions that are changes in behavior.
- Andy's restriction on suid executables that does not honor the
suid bit when the path is from another mount namespace (think
/proc/[pid]/fd/) or when the filesystem was mounted by a less
privileged user.
- The replacement of the user namespace implicit setting of MNT_NODEV
with implicitly setting SB_I_NODEV on the filesystem superblock
instead.
Using SB_I_NODEV is a stronger form that happens to make this state
user invisible. The user visibility can be managed but it caused
problems when it was introduced from applications reasonably
expecting mount flags to be what they were set to.
There is a little bit of work remaining before it is safe to support
mounting filesystems with backing store in user namespaces, beyond
what is in this set of changes.
- Verifying the mounter has permission to read/write the block device
during mount.
- Teaching the integrity modules IMA and EVM to handle filesystems
mounted with only user namespace root and to reduce trust in their
security xattrs accordingly.
- Capturing the mounters credentials and using that for permission
checks in d_automount and the like. (Given that overlayfs already
does this, and we need the work in d_automount it make sense to
generalize this case).
Furthermore there are a few changes that are on the wishlist:
- Get all filesystems supporting posix acls using the generic posix
acls so that posix_acl_fix_xattr_from_user and
posix_acl_fix_xattr_to_user may be removed. [Maintainability]
- Reducing the permission checks in places such as remount to allow
the superblock owner to perform them.
- Allowing the superblock owner to chown files with unmapped uids and
gids to something that is mapped so the files may be treated
normally.
I am not considering even obvious relaxations of permission checks
until it is clear there are no more corner cases that need to be
locked down and handled generically.
Many thanks to Seth Forshee who kept this code alive, and putting up
with me rewriting substantial portions of what he did to handle more
corner cases, and for his diligent testing and reviewing of my
changes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (30 commits)
fs: Call d_automount with the filesystems creds
fs: Update i_[ug]id_(read|write) to translate relative to s_user_ns
evm: Translate user/group ids relative to s_user_ns when computing HMAC
dquot: For now explicitly don't support filesystems outside of init_user_ns
quota: Handle quota data stored in s_user_ns in quota_setxquota
quota: Ensure qids map to the filesystem
vfs: Don't create inodes with a uid or gid unknown to the vfs
vfs: Don't modify inodes with a uid or gid unknown to the vfs
cred: Reject inodes with invalid ids in set_create_file_as()
fs: Check for invalid i_uid in may_follow_link()
vfs: Verify acls are valid within superblock's s_user_ns.
userns: Handle -1 in k[ug]id_has_mapping when !CONFIG_USER_NS
fs: Refuse uid/gid changes which don't map into s_user_ns
selinux: Add support for unprivileged mounts from user namespaces
Smack: Handle labels consistently in untrusted mounts
Smack: Add support for unprivileged mounts from user namespaces
fs: Treat foreign mounts as nosuid
fs: Limit file caps to the user namespace of the super block
userns: Remove the now unnecessary FS_USERNS_DEV_MOUNT flag
userns: Remove implicit MNT_NODEV fragility.
...
Buck and LDO binding name changes.
The binding names for the regulators have been changed to match the current
expectation from existing device tree source files.
This fix rectifies the disparity between what currently exists in some
.dts[i] board files and what is listed in this binding document. This
change re-aligns those differences and also brings the binding document
in-line with the expectations of the product datasheet from Dialog
Semiconductor.
Bucks and LDOs now follow the expected notation:
{ buck1, buck2, buck3, buck4 }
{ ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8, ldo9, ldo10 }
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Fix a nasty (and really hard to debug) memory corruption during
resume from hibernation on x86-64 (that leads to a kernel panic
most of the time) due to the use of a stale stack pointer value
in FRAME_BEGIN (Josh Poimboeuf).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=O25M
-----END PGP SIGNATURE-----
Merge tag 'pm-urgent-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a nasty (and really hard to debug) memory corruption during resume
from hibernation on x86-64 (that leads to a kernel panic most of the
time) due to the use of a stale stack pointer value in FRAME_BEGIN
(Josh Poimboeuf)"
* tag 'pm-urgent-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Fix hibernation return address corruption
Pull more cgroup updates from Tejun Heo:
"I forgot to include the patches which got applied to for-4.7-fixes
late during last cycle.
Eric's three patches fix bugs introduced with the namespace support"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroupns: Only allow creation of hierarchies in the initial cgroup namespace
cgroupns: Close race between cgroup_post_fork and copy_cgroup_ns
cgroupns: Fix the locking in copy_cgroup_ns
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
Pull IDE updates from David Miller:
"Just a couple small bug fixes, nothing overly exciting in here"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: missing break statement in set_timings_mdma()
ide: hpt366: fix incorrect mask when checking at cmd_high_time
ide-tape: fix misprint in failure handling in idetape_init()
cmd640: add __init attribute
Pull sparc updates from David Miller:
1) Double spin lock bug in sunhv serial driver, from Dan Carpenter.
2) Use correct RSS estimate when determining whether to grow the huge
TSB or not, from Mike Kravetz.
3) Don't use full three level page tables for hugepages, PMD level is
sufficient. From Nitin Gupta.
4) Mask out extraneous bits from TSB_TAG_ACCESS register, we only want
the address bits.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Trim page tables for 8M hugepages
sparc64 mm: Fix base TSB sizing when hugetlb pages are used
sparc: serial: sunhv: fix a double lock bug
sparc32: off by ones in BUG_ON()
sparc: Don't leak context bits into thread->fault_address
Things have been calm here - nothing much except for a few fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/rhI
-----END PGP SIGNATURE-----
Merge tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"Things have been calm here - nothing much except for a few fixes"
* tag 'arc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: don't loose PTE_SPECIAL in pte_modify()
ARC: dma: fix address translation in arc_dma_free
ARC: typo fix in mm/ioremap.c
ARC: fix linux-next build breakage
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: off by one in at32_init_pio()
avr32: fixup code style in unistd.h and syscall_table.S
avr32: wire up preadv2 and pwritev2 syscalls
Pull ARM updates from Russell King:
"Included in this update are:
- Patches from Gregory Clement to fix the coherent DMA cases in our
dma-mapping code.
- A number of CPU errata updates and fixes.
- ARM cpuidle improvements from Jisheng Zhang.
- Fix from Kees for the location of _etext.
- Cleanups from Masahiro Yamada to avoid duplicated messages during
the kernel build, and remove CONFIG_ARCH_HAS_BARRIERS.
- Remove a udelay loop limitation, allowing for faster CPUs to
calibrate the delay correctly.
- Cleanup some left-overs from the SW PAN implementation.
- Ensure that a modified address limit is not visible to exception
handlers"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (21 commits)
ARM: 8586/1: cpuidle: make arm_cpuidle_suspend() a bit more efficient
ARM: 8585/1: cpuidle: fix !cpuidle_ops[cpu].init case during init
ARM: 8561/4: dma-mapping: Fix the coherent case when iommu is used
ARM: 8561/3: dma-mapping: Don't use outer_flush_range when the L2C is coherent
ARM: 8560/1: errata: Workaround errata A12 825619 / A17 852421
ARM: 8559/1: errata: Workaround erratum A12 821420
ARM: 8558/1: errata: Workaround errata A12 818325/852422 A17 852423
ARM: save and reset the address limit when entering an exception
ARM: 8577/1: Fix Cortex-A15 798181 errata initialization
ARM: 8584/1: floppy: avoid gcc-6 warning
ARM: 8583/1: mm: fix location of _etext
ARM: 8582/1: remove unused CONFIG_ARCH_HAS_BARRIERS
ARM: 8306/1: loop_udelay: remove bogomips value limitation
ARM: 8581/1: add missing <asm/prom.h> to arch/arm/kernel/devtree.c
ARM: 8576/1: avoid duplicating "Kernel: arch/arm/boot/*Image is ready"
ARM: 8556/1: on a generic DT system: do not touch l2x0
ARM: uaccess: remove put_user() code duplication
ARM: 8580/1: Remove orphaned __addr_ok() definition
ARM: get rid of horrible *(unsigned int *)(regs + 1)
ARM: introduce svc_pt_regs structure
...
Pull fuse updates from Miklos Szeredi:
"This fixes error propagation from writeback to fsync/close for
writeback cache mode as well as adding a missing capability flag to
the INIT message. The rest are cleanups.
(The commits are recent but all the code actually sat in -next for a
while now. The recommits are due to conflict avoidance and the
addition of Cc: stable@...)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use filemap_check_errors()
mm: export filemap_check_errors() to modules
fuse: fix wrong assignment of ->flags in fuse_send_init()
fuse: fuse_flush must check mapping->flags for errors
fuse: fsync() did not return IO errors
fuse: don't mess with blocking signals
new helper: wait_event_killable_exclusive()
fuse: improve aio directIO write performance for size extending writes
This reverts commit 3c9fe8cdff.
As Miklos points out in commit c1b2cc1a76, the "lookup_hash()" helper
is now unused, and in fact, with the hash salting changes, since the
hash of a dentry name now depends on the directory dentry it is in, the
helper function isn't even really likely to be useful.
So rather than keep it around in case somebody else might end up finding
a use for it, let's just remove the helper and not trick people into
thinking it might be a useful thing.
For example, I had obviously completely missed how the helper didn't
follow the normal dentry hashing patterns, and how the hash salting
patch broke overlayfs. Things would quietly build and look sane, but
not work.
Suggested-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull overlayfs update from Miklos Szeredi:
"First of all, this fixes a regression in overlayfs introduced by the
dentry hash salting. I've moved the patch fixing this to the front of
the queue, so if (god forbid) something needs to be bisected in
overlayfs this regression won't interfere with that.
The biggest part is preparation for selinux support, done by Vivek
Goyal. Essentially this makes all operations on underlying
filesystems be done with credentials of mounter. This makes
everything nicely consistent.
There are also fixes for a number of known and recently discovered
non-standard behavior (thanks to Eryu Guan for testing and improving
the test suites)"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: (23 commits)
ovl: simplify empty checking
qstr: constify instances in overlayfs
ovl: clear nlink on rmdir
ovl: disallow overlayfs as upperdir
ovl: fix warning
ovl: remove duplicated include from super.c
ovl: append MAY_READ when diluting write checks
ovl: dilute permission checks on lower only if not special file
ovl: fix POSIX ACL setting
ovl: share inode for hard link
ovl: store real inode pointer in ->i_private
ovl: permission: return ECHILD instead of ENOENT
ovl: update atime on upper
ovl: fix sgid on directory
ovl: simplify permission checking
ovl: do not require mounter to have MAY_WRITE on lower
ovl: do operations on underlying file system in mounter's context
ovl: modify ovl_permission() to do checks on two inodes
ovl: define ->get_acl() for overlay inodes
ovl: move some common code in a function
...
- support for foreign endianess and HP-UP superblocks from
Krzysztof Błaszkowski
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+CpR
-----END PGP SIGNATURE-----
Merge tag 'freevxfs-for-4.8' of git://git.infradead.org/users/hch/freevxfs
Pull freevxfs updates from Christoph Hellwig:
"Support for foreign endianess and HP-UP superblocks from
Krzysztof Błaszkowski"
* tag 'freevxfs-for-4.8' of git://git.infradead.org/users/hch/freevxfs:
freevxfs: update Kconfig information
freevxfs: refactor readdir and lookup code
freevxfs: fix lack of inode initialization
freevxfs: fix memory leak in vxfs_read_fshead()
freevxfs: update documentation and cresdits for HP-UX support
freevxfs: implement ->alloc_inode and ->destroy_inode
freevxfs: avoid the need for forward declaring the super operations
freevxfs: move VFS inode allocation into vxfs_blkiget and vxfs_stiget
freevxfs: remove vxfs_put_fake_inode
freevxfs: handle big endian HP-UX file systems
- a simple error handling fix from Tal Shorer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y8eQ
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.8' of git://git.infradead.org/users/hch/configfs
Pull configfs update from Christoph Hellwig:
"A simple error handling fix from Tal Shorer"
* tag 'configfs-for-4.8' of git://git.infradead.org/users/hch/configfs:
configfs: don't set buffer_needs_fill to zero if show() returns error
Pull CIFS/SMB3 fixes from Steve French:
"Various CIFS/SMB3 fixes, most for stable"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix a possible invalid memory access in smb2_query_symlink()
fs/cifs: make share unaccessible at root level mountable
cifs: fix crash due to race in hmac(md5) handling
cifs: unbreak TCP session reuse
cifs: Check for existing directory when opening file with O_CREAT
Add MF-Symlinks support for SMB 2.0
For PMD aligned (8M) hugepages, we currently allocate
all four page table levels which is wasteful. We now
allocate till PMD level only which saves memory usage
from page tables.
Also, when freeing page table for 8M hugepage backed region,
make sure we don't try to access non-existent PTE level.
Orabug: 22630259
Signed-off-by: Nitin Gupta <nitin.m.gupta@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "Warning" to "warning" to make it look more like a GCC warning.
Hopefully that will be enough to help the 0-day bot or other automated
tools catch this warning earlier before it ends up in Linus's tree.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/b1669f391a5db91040427fd9f8e1e79db18f9709.1469751119.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This fixes the following warning:
Warning: objtool: x86 instruction decoder differs from kernel
Unfortunately we have three identical copies of the x86 instruction
decoder in the kernel tree that have to be manually kept in sync.
It's on my TODO list to at least library-ize the ones in the tools
subdir so we'd only have two of them instead of three. In the meantime,
here's another manual sync.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: c61f4d5eba ("perf tools: Add AVX-512 support to the instruction decoder used by Intel PT")
Link: http://lkml.kernel.org/r/d7f74b4d91fed25b0be33cd5c86f5131fa1a7529.1469751119.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This fixes some false positive objtool warnings seen with gcc 6.1.1:
kernel/trace/ring_buffer.o: warning: objtool: ring_buffer_read_page()+0x36c: sibling call from callable instruction with changed frame pointer
arch/x86/kernel/reboot.o: warning: objtool: native_machine_emergency_restart()+0x139: sibling call from callable instruction with changed frame pointer
lib/xz/xz_dec_stream.o: warning: objtool: xz_dec_run()+0xc2: sibling call from callable instruction with changed frame pointer
With GCC 6, a new code pattern is sometimes used to access a switch
statement jump table in .rodata, which objtool doesn't yet recognize:
mov [rodata addr],%reg1
... some instructions ...
jmpq *(%reg1,%reg2,8)
Add support for detecting that pattern. The detection code is rather
crude, but it's still effective at weeding out false positives and
catching real warnings. It can be refined later once objtool starts
reading DWARF CFI.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/b8c9503b4ad8c8a827cc5400db4c1b40a3ea07bc.1469751119.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Fix the tools/vm/ build by making libapi provide the str_error_c function,
that libapi uses but wasn't part of the list of objects linked with
tools/vm/ programs. (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=eaLq
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-20160728' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fix from Arnaldo Carvalho de Melo:
- Fix the tools/vm/ build by making libapi provide the str_error_c function,
that libapi uses but wasn't part of the list of objects linked with
tools/vm/ programs. (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
FUSE_HAS_IOCTL_DIR should be assigned to ->flags, it may be a typo.
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 69fe05c90e ("fuse: add missing INIT flags")
Cc: <stable@vger.kernel.org>
Rich Felker
Paul Gortmaker
Pan Xinhui
Linus Torvalds
Steve Twiss
Rafael J. Wysocki
Nitin Gupta
Josh Poimboeuf
Ingo Molnar
Miklos Szeredi
Wei Fang