Make use of struct gpio_desc which allows us to specify the active state
of the reset pin.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver was clearing the hold bit in the control register before
writing to the address register which resulted in a stop condition
being generated rather than a repeated start.
This issue was only observed when a system was running much
slower than a normal processor would execute. The IP data sheet
mentions a ordering of writing to the address register before
clearing the hold.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds i2c controller driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support for enforced STOPs will allow us to use SCCB compatible devices.
Based on a preliminary patch by Wolfram Sang.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added myself as maintainer of the Aspeed I2C driver and the associated
I2C interrupt controller and added Joel Stanley and Benjamin
Herrenschmidt as reviewers.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added slave support for Aspeed I2C controller. Supports fourteen busses
present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added initial master support for Aspeed I2C controller. Supports
fourteen busses present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add recent findings (IGNORE_NAK) and document in a bit more detail why
the feature is not possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Definitions were added to core library
- A example was added to designware-core.txt Documentation that shows
how the slave can be setup using DTS
SLAVE related definitions were added to the core of the controller.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- The functions related to I2C master mode of operation were transformed
in a single driver.
- Common definitions were moved to i2c-designware-core.h
- The i2c-designware-core is now only a library file, the functions
associated are in a source file called i2c-designware-common and
are used by both i2c-designware-master and i2c-designware-slave.
- To decrease noise in namespace common i2c_dw_*() functions are
now using ops to keep them private.
- Designware PCI driver had to be changed to match the previous ops
functions implementation.
Almost all of the "core" source is now part of the "master" source. The
difference is the functions used by both modes and they are in the
"common" source file.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Factor out all _master() part of code from i2c-designware-core
and i2c-designware-platdrv to separate functions.
- Standardize all code related with MASTER mode.
- I have to take off DW_IC_INTR_TX_EMPTY from DW_IC_INTR_DEFAULT_MASK
because it is master specific.
The purpose of this is to prepare the controller to have is I2C MASTER
flow in a separate driver. To do this first all the
functions/definitions related to the MASTER flow were identified.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The purpose of this commit is to fix some comments and styling in the
existing code due to the need of reuse this code. What is being made
here is:
- Sorted the headers files
- Corrected some comments style (capital letters, lowcase i2c)
- Reverse tree in the variables declaration
- Add/remove empty lines and tabs where needed
- Fix of misspelled word "endianness" and "transferred"
- Replaced the return variable "r" with the more standard "ret"
The value of this, besides the rules of coding style, is because I
will use this code after and it will make my future patch a lot bigger and
complicated to review. The work here won't bring any additional work to
backported fixes because is just style and reordering.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace '%d' by '%zu' to fix the following type of compilation warnings:
drivers/i2c/busses/i2c-at91.c:277:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 5 has type ‘size_t’ [-Wformat=]
dev_dbg(dev->dev, "wrote 0x%x, to go %d\n", *dev->buf, dev->buf_len);
^
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_prepare_enable() can fail here and we must check its return value.
Also, add a missing clk_disable_unprepare().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive text.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set I2C_CLASS_HWMON for xlp9xx to enable automatic probing of BMC
devices by the ipmi-ssif driver.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added SMBUS PCI Ids for SMBUS for Cannon Lake PCH.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig.
Cover Cannon Lake-H too]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The newly added support for the pcc mailbox fails to build
in some configurations:
drivers/i2c/busses/i2c-xgene-slimpro.c: In function 'xgene_slimpro_i2c_probe':
drivers/i2c/busses/i2c-xgene-slimpro.c:516:25: error: implicit declaration of function 'memremap'; did you mean 'memcmp'? [-Werror=implicit-function-declaration]
drivers/i2c/busses/i2c-xgene-slimpro.c:518:13: error: 'MEMREMAP_WB' undeclared (first use in this function)
drivers/i2c/busses/i2c-xgene-slimpro.c:518:13: note: each undeclared identifier is reported only once for each function it appears in
This includes the missing header file.
Fixes: df5da47fe7 ("i2c: xgene-slimpro: Add ACPI support by using PCC mailbox")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 6c42778780 ("i2c: stub: use pr_fmt") changed the DEBUG
handling and caused build warnings. Revert back to the original.
Fixes: 6c42778780 ("i2c: stub: use pr_fmt")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of printing errors after mxs_i2c_pio_wait_xfer_end returns with
an error code just print a debug message.
NAKs and timeouts can occur in this situation normally, so do not treat
them as errors.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After removal of platform_data support, we can simplify OF handling.
of_match_device() evaluates to NULL if !CONFIG_OF or if there is no node
pointer for that device, so we can remove the check for the node ptr.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No platform currently upstream makes use of this platform_data anymore.
The ones that did are converted to DT meanwhile. So, remove it. The old
platforms likely don't have the 'clks_per_cnt' feature, otherwise it
would have been implemented by now. And in the unlikely case they need
to setup a different bus speed, we should rather go for a generic i2c
platform data just for that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of hard coding "i2c-stub:", let's use the pr_fmt mechanism to
achieve the same more easily. This makes it easier to stay consistent
when adding new messages. Also, remove an unneeded OOM message while we
are here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds ACPI support by using PCC mailbox communication
interface.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch refactors the code to use a single message function to
send command message.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Finally, apply modern comment rules to the file header. The old style
looked very non-Linuxish and challenged my eyes for some time now. I
also added my own copyright for the period of me being the maintainer.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
They seem like cruft to me. I couldn't find any evidence that something
included from there is actually used.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core files were renamed, adapt the textfile to it.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Removes some ifdeffery. Also add the new file to the relevant
MAINTAINERS section.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Break out the exported SMBus functions and the emulation layer into a
separate file. This also involved splitting up the tracing header into
an I2C and an SMBus part.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core became quite huge and its monolithic structure makes
maintenance hard. So, prepare to break out some functionality into
separate files by renaming the source file. Note that we keep the
resulting object name constant to avoid regressions.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull thermal SoC management fixes from Eduardo Valentin:
- fixes to TI SoC driver, Broadcom, qoriq
- small sparse warning fix on thermal core
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: broadcom: ns-thermal: default on iProc SoCs
ti-soc-thermal: Fix a typo in a comment line
ti-soc-thermal: Delete error messages for failed memory allocations in ti_bandgap_build()
ti-soc-thermal: Use devm_kcalloc() in ti_bandgap_build()
thermal: core: make thermal_emergency_poweroff static
thermal: qoriq: remove useless call for of_thermal_get_trip_points()
Here are some serial and tty fixes for 4.12-rc3. They are a bit
"bigger" than normal, which is why I had them "bake" in linux-next for a
few weeks and didn't send them to you for -rc2.
They revert a few of the serdev patches from 4.12-rc1, and bring things
back to how they were in 4.11, to try to make things a bit more stable
there. Rob and Johan both agree that this is the way forward, so this
isn't people squabbling over semantics. Other than that, just a few
minor serial driver fixes that people have had problems with.
All of these have been in linux-next for a few weeks with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWSlOHA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylDCACgn7RHT16JUASggJmRUBeadxQcFQAAnjtxX2kc
0AQLqXxqGyFxVZClAYMy
=Y6+X
-----END PGP SIGNATURE-----
Merge tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some serial and tty fixes for 4.12-rc3. They are a bit bigger
than normal, which is why I had them bake in linux-next for a few
weeks and didn't send them to you for -rc2.
They revert a few of the serdev patches from 4.12-rc1, and bring
things back to how they were in 4.11, to try to make things a bit more
stable there. Rob and Johan both agree that this is the way forward,
so this isn't people squabbling over semantics. Other than that, just
a few minor serial driver fixes that people have had problems with.
All of these have been in linux-next for a few weeks with no reported
issues"
* tag 'tty-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: altera_uart: call iounmap() at driver remove
serial: imx: ensure UCR3 and UFCR are setup correctly
MAINTAINERS/serial: Change maintainer of jsm driver
serial: enable serdev support
tty/serdev: add serdev registration interface
serdev: Restore serdev_device_write_buf for atomic context
serial: core: fix crash in uart_suspend_port
tty: fix port buffer locking
tty: ehv_bytechan: clean up init error handling
serial: ifx6x60: fix use-after-free on module unload
serial: altera_jtaguart: adding iounmap()
serial: exar: Fix stuck MSIs
serial: efm32: Fix parity management in 'efm32_uart_console_get_options()'
serdev: fix tty-port client deregistration
Revert "tty_port: register tty ports with serdev bus"
drivers/tty: 8250: only call fintek_8250_probe when doing port I/O
Fix running SPU programs on Cell, and a few other minor fixes.
Thanks to:
Alistair Popple, Jeremy Kerr, Michael Neuling, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EM32
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix running SPU programs on Cell, and a few other minor fixes.
Thanks to Alistair Popple, Jeremy Kerr, Michael Neuling, Nicholas
Piggin"
* tag 'powerpc-4.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Add PPC_FEATURE userspace bits for SCV and DARN instructions
powerpc/spufs: Fix hash faults for kernel regions
powerpc: Fix booting P9 hash with CONFIG_PPC_RADIX_MMU=N
powerpc/powernv/npu-dma.c: Fix opal_npu_destroy_context() call
selftests/powerpc: Fix TM resched DSCR test with some compilers
Pull x86 fixes from Thomas Gleixner:
"A series of fixes for X86:
- The final fix for the end-of-stack issue in the unwinder
- Handle non PAT systems gracefully
- Prevent access to uninitiliazed memory
- Move early delay calaibration after basic init
- Fix Kconfig help text
- Fix a cross compile issue
- Unbreak older make versions"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
x86/alternatives: Prevent uninitialized stack byte read in apply_alternatives()
x86/PAT: Fix Xorg regression on CPUs that don't support PAT
x86/watchdog: Fix Kconfig help text file path reference to lockup watchdog documentation
x86/build: Permit building with old make versions
x86/unwind: Add end-of-stack check for ftrace handlers
Revert "x86/entry: Fix the end of the stack for newly forked tasks"
x86/boot: Use CROSS_COMPILE prefix for readelf
Pull timer fixlet from Thomas Gleixner:
"Silence dmesg spam by making the posix cpu timer printks depend on
print_fatal_signals"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Make signal printks conditional
Pull RAS fixes from Thomas Gleixner:
"Two fixlets for RAS:
- Export memory_error() so the NFIT module can utilize it
- Handle memory errors in NFIT correctly"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
acpi, nfit: Fix the memory error check in nfit_handle_mce()
x86/MCE: Export memory_error()
Pull perf tooling fixes from Thomas Gleixner:
- Synchronization of tools and kernel headers
- A series of fixes for perf report addressing various failures:
* Handle invalid maps proper
* Plug a memory leak
* Handle frames and callchain order correctly
- Fixes for handling inlines and children mode
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/include: Sync kernel ABI headers with tooling headers
perf tools: Put caller above callee in --children mode
perf report: Do not drop last inlined frame
perf report: Always honor callchain order for inlined nodes
perf script: Add --inline option for debugging
perf report: Fix off-by-one for non-activation frames
perf report: Fix memory leak in addr2line when called by addr2inlines
perf report: Don't crash on invalid maps in `-g srcline` mode
Pull locking fix from Thomas Gleixner:
"A fix for a state leak which was introduced in the recent rework of
futex/rtmutex interaction"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex,rt_mutex: Fix rt_mutex_cleanup_proxy_lock()
Pull kthread fix from Thomas Gleixner:
"A single fix which prevents a use after free when kthread fork fails"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kthread: Fix use-after-free if kthread fork fails
One was simply a memory leak where not all was being freed that should
have been in releasing a file pointer on set_graph_function.
Then Thomas found that the ftrace trampolines were marked for read/write
as well as execute. To shrink the possible attack surface, he added
calls to set them to ro. Which also uncovered some other issues with
freeing module allocated memory that had its permissions changed.
Kprobes had a similar issue which is fixed and a selftest was added
to trigger that issue again.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJZKOiVFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
vBoH/jxVozuAEVCv+Nbj6fhRxe4emjo0lZZb32EbEaSV/nUQGqHIZFdDQtbt+ld+
sn06/BSMBI+L4BqLj1BCAW0e/zIn/4birIg53SX5jQwc3AlhUG7HS2d+RJZZCrp9
Zofq9L6xZ4Hl2XjkPXqwEgtrwxQtkIPLlJqeYDJ6BVrlPfOPEwB7bfR7B684wiYT
6h2Qo7f/ZQzgJ1sK8N2IjHEnAgE08KCYcj4IB4WHJk6SqQz3bv1Y00WBg2UQihVT
TPPSVhYLnrSw53fxyALqZbHo2DvnQf1TnNadWxvSIpbvgm/T5GG60FDtvHgNfbwz
yKuKAog+P9xBLkoAcfvODLY9O5s=
=75TZ
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fixes from Steven Rostedt:
"There's been a few memory issues found with ftrace.
One was simply a memory leak where not all was being freed that should
have been in releasing a file pointer on set_graph_function.
Then Thomas found that the ftrace trampolines were marked for
read/write as well as execute. To shrink the possible attack surface,
he added calls to set them to ro. Which also uncovered some other
issues with freeing module allocated memory that had its permissions
changed.
Kprobes had a similar issue which is fixed and a selftest was added to
trigger that issue again"
* tag 'trace-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
ftrace use module_alloc() to allocate trampoline pages. The mapping of
module_alloc() is RWX, which makes sense as the memory is written to right
after allocation. But nothing makes these pages RO after writing to them.
Add proper set_memory_rw/ro() calls to protect the trampolines after
modification.
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1705251056410.1862@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
With function tracing starting in early bootup and having its trampoline
pages being read only, a bug triggered with the following:
kernel BUG at arch/x86/mm/pageattr.c:189!
invalid opcode: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 4.12.0-rc2-test+ #3
Hardware name: MSI MS-7823/CSM-H87M-G43 (MS-7823), BIOS V1.6 02/22/2014
task: ffffffffb4222500 task.stack: ffffffffb4200000
RIP: 0010:change_page_attr_set_clr+0x269/0x302
RSP: 0000:ffffffffb4203c88 EFLAGS: 00010046
RAX: 0000000000000046 RBX: 0000000000000000 RCX: 00000001b6000000
RDX: ffffffffb4203d40 RSI: 0000000000000000 RDI: ffffffffb4240d60
RBP: ffffffffb4203d18 R08: 00000001b6000000 R09: 0000000000000001
R10: ffffffffb4203aa8 R11: 0000000000000003 R12: ffffffffc029b000
R13: ffffffffb4203d40 R14: 0000000000000001 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff9a639ea00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff9a636b384000 CR3: 00000001ea21d000 CR4: 00000000000406b0
Call Trace:
change_page_attr_clear+0x1f/0x21
set_memory_ro+0x1e/0x20
arch_ftrace_update_trampoline+0x207/0x21c
? ftrace_caller+0x64/0x64
? 0xffffffffc029b000
ftrace_startup+0xf4/0x198
register_ftrace_function+0x26/0x3c
function_trace_init+0x5e/0x73
tracer_init+0x1e/0x23
tracing_set_tracer+0x127/0x15a
register_tracer+0x19b/0x1bc
init_function_trace+0x90/0x92
early_trace_init+0x236/0x2b3
start_kernel+0x200/0x3f5
x86_64_start_reservations+0x29/0x2b
x86_64_start_kernel+0x17c/0x18f
secondary_startup_64+0x9f/0x9f
? secondary_startup_64+0x9f/0x9f
Interrupts should not be enabled at this early in the boot process. It is
also fine to leave interrupts enabled during this time as there's only one
CPU running, and on_each_cpu() means to only run on the current CPU.
If early_boot_irqs_disabled is set, it is safe to run cpu_flush_range() with
interrupts disabled. Don't trigger a BUG_ON() in that case.
Link: http://lkml.kernel.org/r/20170526093717.0be3b849@gandalf.local.home
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Chris Packham
Matt Weber
Baoyou Xie
Jean Delvare
Brendan Higgins
Wolfram Sang
Arvind Yadav
Luis Oliveira
George Cherian
Srinivas Pandruvada
Arnd Bergmann
Wolfram Sang
Michael Thalmeier
Hoan Tran
Linus Torvalds
Thomas Gleixner
Steven Rostedt (VMware)