Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
- new driver: gpio-modepin (plus relevant change in zynqmp firmware)
- add interrupt support to gpio-virtio
- enable the 'gpio-line-names' property in the DT bindings for gpio-rockchip
- use the subsystem helpers where applicable in gpio-uniphier instead of
accessing IRQ structures directly
- code shrink in gpio-xilinx
- add interrupt to gpio-mlxbf2 (and include the removal of custom interrupt
code from the mellanox ethernet driver)
- support multiple interrupts per bank in gpio-tegra186 (and force one interrupt
per bank in older models)
- fix GPIO line IRQ offset calculation in gpio-realtek-otto
- drop unneeded MODULE_ALIAS expansions in multiple drivers
- code cleanup in gpio-aggregator
- minor improvements in gpio-max730x and gpio-mc33880
- Kconfig cleanups
-----BEGIN PGP SIGNATURE-----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=mKh0
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have a single new driver, new features in others and some cleanups
all over the place.
Nothing really stands out and it is all relatively small.
- new driver: gpio-modepin (plus relevant change in zynqmp firmware)
- add interrupt support to gpio-virtio
- enable the 'gpio-line-names' property in the DT bindings for
gpio-rockchip
- use the subsystem helpers where applicable in gpio-uniphier instead
of accessing IRQ structures directly
- code shrink in gpio-xilinx
- add interrupt to gpio-mlxbf2 (and include the removal of custom
interrupt code from the mellanox ethernet driver)
- support multiple interrupts per bank in gpio-tegra186 (and force
one interrupt per bank in older models)
- fix GPIO line IRQ offset calculation in gpio-realtek-otto
- drop unneeded MODULE_ALIAS expansions in multiple drivers
- code cleanup in gpio-aggregator
- minor improvements in gpio-max730x and gpio-mc33880
- Kconfig cleanups"
* tag 'gpio-updates-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
virtio_gpio: drop packed attribute
gpio: virtio: Add IRQ support
gpio: realtek-otto: fix GPIO line IRQ offset
gpio: clean up Kconfig file
net: mellanox: mlxbf_gige: Replace non-standard interrupt handling
gpio: mlxbf2: Introduce IRQ support
gpio: mc33880: Drop if with an always false condition
gpio: max730x: Make __max730x_remove() return void
gpio: aggregator: Wrap access to gpiochip_fwd.tmp[]
gpio: modepin: Add driver support for modepin GPIO controller
dt-bindings: gpio: zynqmp: Add binding documentation for modepin
firmware: zynqmp: Add MMIO read and write support for PS_MODE pin
gpio: tps65218: drop unneeded MODULE_ALIAS
gpio: max77620: drop unneeded MODULE_ALIAS
gpio: xilinx: simplify getting .driver_data
gpio: tegra186: Support multiple interrupts per bank
gpio: tegra186: Force one interrupt per bank
gpio: uniphier: Use helper functions to get private data from IRQ data
gpio: uniphier: Use helper function to get IRQ hardware number
dt-bindings: gpio: add gpio-line-names to rockchip,gpio-bank.yaml
Currently we have a global spi_add_lock which we take when adding new
devices so that we can check that we're not trying to reuse a chip
select that's already controlled. This means that if the SPI device is
itself a SPI controller and triggers the instantiation of further SPI
devices we trigger a deadlock as we try to register and instantiate
those devices while in the process of doing so for the parent controller
and hence already holding the global spi_add_lock. Since we only care
about concurrency within a single SPI bus move the lock to be per
controller, avoiding the deadlock.
This can be easily triggered in the case of spi-mux.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
An spi or i2c remove callback is only called for devices that probed
successfully. In this case this implies that __max730x_probe() set a
non-NULL driver data. So the check ts == NULL is never true. With this
check dropped, __max730x_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
All these functions have no callers apart from drivers/spi/spi.c. So
drop their declarations in include/linux/spi/spi.h and don't export
them.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211007121415.2401638-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The functions in the platform data struct to initialize, cleanup and
apply custom filters are not in use by any mainline board.
Remove support for them to pave the road for more cleanups to come.
The enum was moved as it has no users outside of the driver code
itself.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20210907200726.2034962-3-daniel@zonque.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- new driver: gpio-virtio allowing a guest VM running linux to access
GPIO lines provided by the host
- split the GPIO driver out of the rockchip pin control driver
- add support for a new model to gpio-aspeed-sgpio, refactor the driver
and use generic device property interfaces, improve property sanitization
- add ACPI support to gpio-tegra186
- improve the code setting the line names to support multiple GPIO banks
per device
- constify a bunch of OF functions in the core GPIO code and make the
declaration for one of the core OF functions we use consistent within its
header
- use software nodes in intel_quark_i2c_gpio
- add support for the gpio-line-names property in gpio-mt7621
- use the standard GPIO function for setting the GPIO names in gpio-brcmstb
- fix a bunch of leaks and other bugs in gpio-mpc8xxx
- use generic pm callbacks in gpio-ml-ioh
- improve resource management and PM handling in gpio-mlxbf2
- modernize and improve the gpio-dwapb driver
- coding style improvements in gpio-rcar
- documentation fixes and improvements
- update the MAINTAINERS entry for gpio-zynq
- minor tweaks in several drivers
-----BEGIN PGP SIGNATURE-----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=y/RY
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We mostly have various improvements and refactoring all over the place
but also some interesting new features - like the virtio GPIO driver
that allows guest VMs to use host's GPIOs. We also have a new/old GPIO
driver for rockchip - this one has been split out of the pinctrl
driver.
Summary:
- new driver: gpio-virtio allowing a guest VM running linux to access
GPIO lines provided by the host
- split the GPIO driver out of the rockchip pin control driver
- add support for a new model to gpio-aspeed-sgpio, refactor the
driver and use generic device property interfaces, improve property
sanitization
- add ACPI support to gpio-tegra186
- improve the code setting the line names to support multiple GPIO
banks per device
- constify a bunch of OF functions in the core GPIO code and make the
declaration for one of the core OF functions we use consistent
within its header
- use software nodes in intel_quark_i2c_gpio
- add support for the gpio-line-names property in gpio-mt7621
- use the standard GPIO function for setting the GPIO names in
gpio-brcmstb
- fix a bunch of leaks and other bugs in gpio-mpc8xxx
- use generic pm callbacks in gpio-ml-ioh
- improve resource management and PM handling in gpio-mlxbf2
- modernize and improve the gpio-dwapb driver
- coding style improvements in gpio-rcar
- documentation fixes and improvements
- update the MAINTAINERS entry for gpio-zynq
- minor tweaks in several drivers"
* tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (35 commits)
gpio: mpc8xxx: Use 'devm_gpiochip_add_data()' to simplify the code and avoid a leak
gpio: mpc8xxx: Fix a potential double iounmap call in 'mpc8xxx_probe()'
gpio: mpc8xxx: Fix a resources leak in the error handling path of 'mpc8xxx_probe()'
gpio: viperboard: remove platform_set_drvdata() call in probe
gpio: virtio: Add missing mailings lists in MAINTAINERS entry
gpio: virtio: Fix sparse warnings
gpio: remove the obsolete MX35 3DS BOARD MC9S08DZ60 GPIO functions
gpio: max730x: Use the right include
gpio: Add virtio-gpio driver
gpio: mlxbf2: Use DEFINE_RES_MEM_NAMED() helper macro
gpio: mlxbf2: Use devm_platform_ioremap_resource()
gpio: mlxbf2: Drop wrong use of ACPI_PTR()
gpio: mlxbf2: Convert to device PM ops
gpio: dwapb: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert GPIO to use software nodes
gpio: dwapb: Read GPIO base from gpio-base property
gpio: dwapb: Unify ACPI enumeration checks in get_irq() and configure_irqs()
gpiolib: Deduplicate forward declaration in the consumer.h header
MAINTAINERS: update gpio-zynq.yaml reference
gpio: tegra186: Add ACPI support
...
<linux/spi/max7301.h> despite the placement of the header, is
used by drivers/gpio/gpio-max730*.
The include needs struct gpio_chip and needs to include
<linux/gpio/driver.h> not the legacy <linux/gpio.h> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This patch modified set_cs_timing parameter, no need pass in spi_delay
to set_cs_timing callback.
By the way, we modified the mediatek and tegra114 spi driver to fix build err.
In mediatek spi driver, We have support set absolute time not clk_count,
and call this function in prepare_message not user's API.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210804133746.6742-1-Mason.Zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As we know, spi core layer has removed spi_set_cs_timing() API.
So this patch moved spi_delay for cs_timing from spi_controller
to spi_device, because cs timing should be set by spi_device but
not controller.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210804133716.32040-1-Mason.Zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix kernel-doc warning in spi.h by adding the missing kernel-doc entry
and also correct the original comment so that they both indicate the
correct polarity of the flag.
../include/linux/spi/spi.h:673: warning: Function parameter or member 'devm_allocated' not described in 'spi_controller'
Fixes: 794aaf0144 ("spi: Fix use-after-free with devm_spi_alloc_*")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: William A. Kennington III <wak@google.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20210628210520.5712-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers like qcom geni need the parent device to be used for
dma mapping, so add a dma_map_dev field and let drivers fill this to be
used as mapping device
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210625052213.32260-4-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce support for ancillary devices, similar to existing
implementation for I2C. This is useful for devices having
multiple chip-selects, for example some microcontrollers
provide a normal SPI interface and a flashing SPI interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210621175359.126729-2-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No one seems to be using this global and exported function, so remove it
as it is no longer needed.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210609071918.2852069-1-gregkh@linuxfoundation.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series adds support for the spi_mem_poll_status() spinand
interface.
Some QSPI controllers allows to poll automatically memory
status during operations (erase, read or write). This allows to
offload the CPU for this task.
STM32 QSPI is supporting this feature, driver update are also
part of this series.
Changes in v5:
- Update spi_mem_read_status() description.
- Update poll_status() description API by indicating that data buffer is
filled with last status value.
- Update timeout parameter by timeout_ms in spi_mem_poll_status() prototype.
- Remove parenthesys arount -EINVAL in spi_mem_poll_status().
- Add missing spi_mem_supports_op() call in stm32_qspi_poll_status().
- Add Boris Reviewed-by for patch 1 and 2.
Changes in v4:
- Remove init_completion() from spi_mem_probe() added in v2.
- Add missing static for spi_mem_read_status().
- Check if operation in spi_mem_poll_status() is a READ.
- Update patch 2 commit message.
- Add comment which explains how delays has been calculated.
- Rename SPINAND_STATUS_TIMEOUT_MS to SPINAND_WAITRDY_TIMEOUT_MS.
Chnages in v3:
- Add spi_mem_read_status() which allows to read 8 or 16 bits status.
- Add initial_delay_us and polling_delay_us parameters to spi_mem_poll_status().
and also to poll_status() callback.
- Move spi_mem_supports_op() in SW-based polling case.
- Add delay before invoquing read_poll_timeout().
- Remove the reinit/wait_for_completion() added in v2.
- Add initial_delay_us and polling_delay_us parameters to spinand_wait().
- Add SPINAND_READ/WRITE/ERASE/RESET_INITIAL_DELAY_US and
SPINAND_READ/WRITE/ERASE/RESET_POLL_DELAY_US defines.
- Remove spi_mem_finalize_op() API added in v2.
Changes in v2:
- Indicates the spi_mem_poll_status() timeout unit
- Use 2-byte wide status register
- Add spi_mem_supports_op() call in spi_mem_poll_status()
- Add completion management in spi_mem_poll_status()
- Add offload/non-offload case management in spi_mem_poll_status()
- Optimize the non-offload case by using read_poll_timeout()
- mask and match stm32_qspi_poll_status()'s parameters are 2-byte wide
- Make usage of new spi_mem_finalize_op() API in
stm32_qspi_wait_poll_status()
Patrice Chotard (3):
spi: spi-mem: add automatic poll status functions
mtd: spinand: use the spi-mem poll status APIs
spi: stm32-qspi: add automatic poll status feature
drivers/mtd/nand/spi/core.c | 45 +++++++++++++------
drivers/spi/spi-mem.c | 86 ++++++++++++++++++++++++++++++++++++
drivers/spi/spi-stm32-qspi.c | 86 ++++++++++++++++++++++++++++++++----
include/linux/mtd/spinand.h | 22 +++++++++
include/linux/spi/spi-mem.h | 16 +++++++
5 files changed, 234 insertions(+), 21 deletions(-)
base-commit: 6efb943b86
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
With STM32 QSPI, it is possible to poll the status register of the device.
This could be done to offload the CPU during an operation (erase or
program a SPI NAND for example).
spi_mem_poll_status API has been added to handle this feature.
This new function take care of the offload/non-offload cases.
For the non-offload case, use read_poll_timeout() to poll the status in
order to release CPU during this phase.
For example, previously, when erasing large area, in non-offload case,
CPU load can reach ~50%, now it decrease to ~35%.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/r/20210518162754.15940-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
While fixing undefined behaviour the commit f60d7270c8 ("spi: Avoid
undefined behaviour when counting unused native CSs") missed the case
when all CSs are GPIOs and thus unused_native_cs will be evaluated to
-1 in unsigned representation. This will falsely trigger a condition
in the spi_get_gpio_descs().
Switch to signed types for *_native_cs SPI controller fields to fix above.
Fixes: f60d7270c8 ("spi: Avoid undefined behaviour when counting unused native CSs")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510131242.49455-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The two headers have quite different ifdeffery to prevent multiple inclusion.
Unify them with the pattern that in particular reflects their location.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the data structure is only referred by pointer, compiler may not need
to see the contents of the data type. Thus, we may replace header inclusions
by respective forward declarations. Due to above add missed headers as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups.
-----BEGIN PGP SIGNATURE-----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=WL87
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups"
* tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (79 commits)
mmc: block: Issue a cache flush only when it's enabled
memstick: r592: ignore kfifo_out() return code again
mmc: block: Update ext_csd.cache_ctrl if it was written
mmc: mmc_spi: Make of_mmc_spi.c resource provider agnostic
mmc: mmc_spi: Use already parsed IRQ
mmc: mmc_spi: Drop unused NO_IRQ definition
mmc: mmc_spi: Set up polling even if voltage-ranges is not present
mmc: core: Convert mmc_of_parse_voltage() to use device property API
mmc: core: Correct descriptions in mmc_of_parse()
mmc: dw_mmc-rockchip: Just set default sample value for legacy mode
mmc: sdhci-s3c: constify uses of driver/match data
mmc: sdhci-s3c: correct kerneldoc of sdhci_s3c_drv_data
mmc: sdhci-s3c: simplify getting of_device_id match data
mmc: tmio: always restore irq register
mmc: sdhci-pci-gli: Enlarge ASPM L1 entry delay of GL975x
mmc: core: Let eMMC sanitize not retry in case of timeout/failure
mmc: core: Add a retries parameter to __mmc_switch function
memstick: r592: remove unused variable
mmc: sdhci-st: Remove unnecessary error log
mmc: sdhci-msm: Remove unnecessary error log
...
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
struct spi_transfer is declared twice. One is declared at 24th line.
The blew one is not needed though. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20210401065904.994121-1-wanjiabing@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
The older API used to supply additional device properties for the
devices - so mainly the function device_add_properties() - is going to
be removed. The reason why the API will be removed is because it gives
false impression that the properties are assigned directly to the
devices, which has actually never been the case - the properties have
always been assigned to a software fwnode which was then just directly
linked with the device when the old API was used. By only accepting
device properties instead of complete software nodes, the subsystems
remove any change of taking advantage of the other features the
software nodes have.
The change that is required from the spi subsystem and the drivers is
trivial. Basically only the "properties" member in struct
spi_board_info, which was a pointer to struct property_entry, is
replaced with a pointer to a complete software node.
thanks,
Heikki Krogerus (4):
spi: Add support for software nodes
ARM: pxa: icontrol: Constify the software node
ARM: pxa: zeus: Constify the software node
spi: Remove support for dangling device properties
arch/arm/mach-pxa/icontrol.c | 12 ++++++++----
arch/arm/mach-pxa/zeus.c | 6 +++++-
drivers/spi/spi.c | 21 ++++++---------------
include/linux/spi/spi.h | 7 +++----
4 files changed, 22 insertions(+), 24 deletions(-)
--
2.30.1
base-commit: a38fd87484
Making it possible for the drivers to assign complete
software fwnodes to the devices instead of only the device
properties in those nodes.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210303152814.35070-2-heikki.krogerus@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'delay' field in the spi_transfer struct is meant to replace the
'delay_usecs' field. However some cleanup was required to remove the
uses of 'delay_usecs'. Now that it's been cleaned up, we can remove it
from the kernel tree.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210308145502.1075689-10-aardelean@deviqon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Convert to GPIO descriptors
- Fix-ups
- Trivial: Fix coding style: sky81452-backlight
- Ensure backlight state is known on bring-up; ktd253-backlight
- Use common Platform API; qcom-wled, fbdev
-----BEGIN PGP SIGNATURE-----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=GPmS
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Functionality:
- Convert to GPIO descriptors
Fix-ups:
- Trivial: fix coding style in sky81452-backlight
- Ensure backlight state is known on bring-up in ktd253
- Use common platform API in qcom-wled and fbdev"
* tag 'backlight-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight/video: Use Platform getter/setter functions
backlight: ktd253: Bring up in a known state
backlight: sky81452-backlight: Convert comma to semicolon
backlight: lms283gf05: Convert to GPIO descriptors
The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware. Otherwise mostly
thanks to Arnd's cleanup efforts on old platforms we've removed several
obsolete drivers which just about balance out the newer drivers we've
added this cycle.
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolute EFM32, Txx9 and SIRF Prima and Atlas drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAq3M0ACgkQJNaLcl1U
h9Aq3gf6AuboDwFguKZAmXp27zjYsv5o5KtPyycTltIIfjGuA58+fN2zQT+puoGI
wzafjk9R73Foa67YKUwClaBGZNZbYOkB2iOk9a+/sku6k3jO14moybpMuL32dCVe
lutKd9D4n8/J5UHX3SHKHAZ9r2vp28rlaZa4wd79Ww5r+BLajUcrkjtr4GVT5k1k
WzzC0nUjE/zg1oV+PlakMolwK+iBCQYTT7S4r/OQAABQIkXXdtwmGvFUUXpGVF19
GUs52XI8QzK5504Xl+F7NF1+2zHovO11PTHnd+rAe6AfA/NGggtk6O1Y9R4tQHF9
TN6PHukNxUdTFfe6RTbSzPagpFydvQ==
=/4Ve
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware.
Otherwise mostly thanks to Arnd's cleanup efforts on old platforms
we've removed several obsolete drivers which just about balance out
the newer drivers we've added this cycle.
Summary:
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in
spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolete EFM32, Txx9 and SIRF Prima and Atlas drivers"
* tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (76 commits)
spi: Skip zero-length transfers in spi_transfer_one_message()
spi: dw: Avoid stack content exposure
spi: cadence-quadspi: Use spi_mem_dtr_supports_op()
spi: spi-mem: add spi_mem_dtr_supports_op()
spi: atmel-quadspi: Disable the QSPI IP at suspend()
spi: pxa2xx: Add IDs for the controllers found on Intel Lynxpoint
spi: pxa2xx: Fix the controller numbering for Wildcat Point
spi: Change provied to provided in the file spi.h
spi: mediatek: add set_cs_timing support
spi: support CS timing for HW & SW mode
spi: add power control when set_cs_timing
spi: stm32: make spurious and overrun interrupts visible
spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC
spi: stm32: defer probe for reset
spi: stm32: driver uses reset controller only at init
spi: stm32h7: ensure message are smaller than max size
spi: stm32: use bitfield macros
spi: stm32: do not mandate cs_gpio
spi: stm32: properly handle 0 byte transfer
spi: clps711xx: remove redundant white-space
...
spi_mem_default_supports_op() rejects DTR ops by default to ensure that
the controller drivers that haven't been updated with DTR support
continue to reject them. It also makes sure that controllers that don't
support DTR mode at all (which is most of them at the moment) also
reject them.
This means that controller drivers that want to support DTR mode can't
use spi_mem_default_supports_op(). Driver authors have to roll their own
supports_op() function and mimic the buswidth checks. See
spi-cadence-quadspi.c for example. Or even worse, driver authors might
skip it completely or get it wrong.
Add spi_mem_dtr_supports_op(). It provides a basic sanity check for DTR
ops and performs the buswidth requirement check. Move the logic for
checking buswidth in spi_mem_default_supports_op() to a separate
function so the logic is not repeated twice.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210204141218.32229-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210125150238.16980-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the lms283gf05 backlight driver to use GPIO
descriptors and switches the single PXA Palm Z2 device
over to defining these.
Since the platform data was only used to convey GPIO
information we can delete the platform data header.
Notice that we define the proper active low semantics in
the board file GPIO descriptor table (active low) and
assert the reset line by bringing it to "1" (asserted).
Cc: Marek Vasut <marex@denx.de>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch marks dummy transfer by setting dummy_data bit to 1.
Controllers supporting dummy transfer by hardware use this bit field
to skip software transfer of dummy bytes and use hardware dummy bytes
transfer.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1608585459-17250-6-git-send-email-skomatineni@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Transmit/receive only is a valid SPI mode. For example, the MOSI/TX line
might be missing from an ADC while for a DAC the MISO/RX line may be
optional. This patch adds these two new modes: SPI_NO_TX and
SPI_NO_RX. This way, the drivers will be able to identify if any of
these two lines is missing and to adjust the transfers accordingly.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-2-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change moves all the SPI mode bits into a separate 'spi.h' header in
uAPI. This is meant to re-use these definitions inside the kernel as well
as export them to userspace (via uAPI).
The SPI mode definitions have usually been duplicated between between
'include/linux/spi/spi.h' and 'include/uapi/linux/spi/spidev.h', so
whenever adding a new entry, this would need to be put in both headers.
They've been moved from 'include/linux/spi/spi.h', since that seems a bit
more complete; the bits have descriptions and there is the SPI_MODE_X_MASK.
This change also does a conversion of these bitfields to _BITUL() macro.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_controller()
spi_unregister_controller()
That's because spi_unregister_controller() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_controller which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_controller struct. Thus, once spi_unregister_controller()
has been called, the private data is inaccessible. But some drivers
need to access it after spi_unregister_controller() to perform further
teardown steps.
Introduce devm_spi_alloc_master() and devm_spi_alloc_slave(), which
release a reference on the spi_controller struct only after the driver
has unbound, thereby keeping the memory allocation accessible. Change
spi_unregister_controller() to not release a reference if the
spi_controller was allocated by one of these new devm functions.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_controller in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm functions
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the controller.
That commit shall amend spi_unregister_controller() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/272bae2ef08abd21388c98e23729886663d19192.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a macro to filter all SPI_MODE_0,1,2,3 mode in one run.
The latest SPI framework will parse the devicetree in following call
sequence: of_register_spi_device() -> of_spi_parse_dt()
So, driver do not need to pars the devicetree and will get prepared
flags in the probe.
On one hand it is good far most drivers. On other hand some drivers need to
filter flags provide by SPI framework and apply know to work flags. This drivers
may use SPI_MODE_X_MASK to filter MODE flags and set own, known flags:
spi->flags &= ~SPI_MODE_X_MASK;
spi->flags |= SPI_MODE_0;
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201027095724.18654-2-o.rempel@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Storage technologies like FRAM have no "write pages", the whole chip can
be written within one SPI transfer. For these chips, the page size can
be set equal to the device size. Currently available devices are already
bigger than 64 kiB.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Link: https://lore.kernel.org/r/20200727111218.26926-1-ceggers@arri.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ_EINT0 constant is a platform detail that is
defined in mach/irqs.h and not visible to drivers once
that header is made private.
Since the same calculation already happens in s3c24xx_set_fiq,
just return the value from there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-31-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The fiq handler needs access to some register definitions that
should not be used directly by device drivers.
Since this is closely related to the irqchip driver anyway,
move it into the same place.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[krzk: Add a header guard in include/linux/spi/s3c24xx-fiq.h, fix
SPDX comment style, update maintainer's entry]
Co-developed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-23-krzk%40kernel.org
Acked-by: Mark Brown <broonie@kernel.org>
Linus Torvalds
Mark Brown
Uwe Kleine-König
Daniel Mack
Linus Walleij
Mason Zhang
Randy Dunlap
Vinod Koul
Sebastian Reichel
Greg Kroah-Hartman
Patrice Chotard
Andy Shevchenko
Matthew Gerlach
William A. Kennington III
Wan Jiabing
Heikki Krogerus
Alexandru Ardelean
Pratyush Yadav
Bhaskar Chowdhury
Sowjanya Komatineni
Dragos Bogdan
Alexandru Ardelean
Lukas Wunner
Oleksij Rempel
Christian Eggers
Arnd Bergmann