The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
Degrade the "Unsupported chip" message from info to debug level.
There's nothing wrong with this, so no need to bother the user.
Also make the message slightly more descriptive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The encoding of temperatures varies between chips and modes. So do not
use "temp1" or "temp2" in the names of the conversion functions, but
specify the encoding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Use static functions instead of the TEMPx_FROM_REG* and TEMPx_TO_REG*
macros. This will ensure type safety and eliminate any side effects
from arguments passed in since the macros referenced 'val' multiple
times. This change should not affect functionality.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim chips supported by the lm90 driver have 8-bit high and low
remote limit values, not 11-bit as the other chips have. So stop reading
from and writing to registers that do not exist on these chips. Also
round the limit values set by the user properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
Move the code which aggregates two 8-bit register values into a 16-bit
value to a separate function. We'll need to do it a second time soon and
I don't want to duplicate the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The new-style lm90 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Many I2C hwmon drivers define a driver ID but no other code references
these, meaning that they are useless. Discard them, along with a few
IDs which are defined but never used at all.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
As indirectly reported by Olof Johansson, the lm90 driver uses a
custom i2c read function even during detection, at which point we
don't know yet what device we're talking with. It would make more
sense to only use the generic i2c read function at this point, so
that we don't log irrelevant errors on misdetection.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Now that we have standard sysfs names to export temperature offset
values, add this feature to the lm90 driver. All supported chips
except the MAX6657, MAX6658 and MAX6659 support it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Convert from class_device to device for hwmon_device_register/unregister
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=32c82a934759b2c9939c9e25865c2d7d1204b9e8
broke lm90 for my (Asus V6VA) laptop.
Before 2.6.23-rc1 and with the following patch, I get:
[g ~]$ sensors
max6657-i2c-0-4c
Adapter: SMBus I801 adapter at 0400
M/B Temp: +64°C (low = +0°C, high = +127°C)
CPU Temp: +78.9°C (low = +73.2°C, high = +88.2°C)
M/B Crit: +105°C (hyst = +95°C)
CPU Crit: +105°C (hyst = +95°C)
Which regressed into:
[g ~]$ sensors
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
zsh: 2701 exit 1 sensors
and dmesg contains:
i2c-adapter i2c-0: Unsupported chip (man_id=0x4D, chip_id=0x4D).
It seems to be a typo, as address 0X4F is mentionned nowhere else in the file,
and my chip is actually at 0x4C.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
We have the following naming convention documented in
Documentation/hwmon/sysfs-interface for fault files:
in[0-*]_input_fault
fan[1-*]_input_fault
temp[1-*]_input_fault
Some drivers follow this convention (lm63, lm83, lm90, smsc47m192).
However some drivers omit the "input" part and create files named
fan1_fault (pc87427) or temp1_fault (dme1737). And the new "generic"
libsensors follows this second (non-standard) convention, so it fails
to report fault conditions for drivers which follow the standard.
We want a single naming scheme, and everyone seems to prefer the
shorter variant, so let's go for it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
hwmon: Fix unchecked return status, batch 4
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Note: f71805f actually checked the status from device_create_file
already. However it did not remove the files on device destruction.
It was also an opportunity to use sysfs_create/remove_group instead
of hand-made loops. This makes the changes much more important but
I think the result is worth it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Add individual alarm files to 4 drivers
Add individual sysfs files for all f71805f, lm63, lm83 and lm90 alarm
and fault conditions. This is a requirement for the planned
chip-independent libsensors. Almost all other hwmon drivers will need
the same improvement.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
convert drivers/hwmon/*.c semaphore use to mutexes.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
all affected hwmon drivers were build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the hwmon drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the I2C addresses for the ADM1032 and ADT7461 chips.
Also update the links to the Analog Devices web site.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PEC support to the lm90 driver. Only the ADM1032 chip supports it,
and in a rather tricky way, which is why this patch comes with
documentation reinforcements. At least, this demonstrates that the new
PEC support logic in i2c-core can properly deal with chips with partial
PEC support.
As enabling PEC causes a significant performance drop, it can be
disabled through a sysfs file (unsurprisingly named "pec").
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Preparatory patch to add PEC support to the lm90 driver. We need a
centralized function to read register values, where the PEC code will
be later inserted. A positive side effect is that read errors are now
handled properly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc instead of kmalloc+memset in all hardware monitoring
drivers.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe and i2c_detect now do the exact same thing and operate on
the same data structure, so we can have everyone call i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.
Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill normal_isa in header files, documentation and all chip drivers, as
it is no more used.
normal_i2c could be renamed to normal, but I decided not to do so at the
moment, so as to limit the number of changes. This might be done later
as part of the i2c_probe/i2c_detect merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies sensors chip drivers to make use of the new
sysfs class "hwmon".
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Part 2: Move the driver files themselves.
Note that the patch "adds trailing whitespace", because it does move the
files as-is, and some files happen to have trailing whitespace.
From: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare
Ben Hutchings
Nate Case
Mark M. Hoffman
Tony Jones
Guillaume Chazarain
Rainer Birkenmaier
Ingo Molnar
Greg Kroah-Hartman
Laurent Riffard
Deepak Saxena