The variable tid is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200701135221.549700-1-colin.king@canonical.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was invoking PCI helper functions like pci_save/restore_state(),
pci_enable/disable_device() and pci_set_power_state(), which is not
recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629072525.156154-3-vaibhavgupta40@gmail.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was invoking PCI helper functions like pci_save/restore_state(),
pci_enable/disable_device() and pci_set_power_state(), which is not
recommended.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629072525.156154-2-vaibhavgupta40@gmail.com
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
In the case of adm8211, after removing PCI helper functions, .suspend()
and .resume() became empty-body functions. Hence, define them NULL and
use dev_pm_ops.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629035031.169670-1-vaibhavgupta40@gmail.com
With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves. The required operations are
done by PCI core.
PCI drivers are not expected to invoke PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
pci_set_power_state(), etc. Their tasks are completed by PCI core itself.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200624174048.64754-1-vaibhavgupta40@gmail.com
Earlier, drivers had to manage the device's power states, and related
operations, themselves. With the generic approach, these are done by PCI
core.
The only driver-specific jobs, .suspend() and .resume() doing were invoking
PCI helper functions pci_save/restore_state() and
pci_set_power_state(). This is not recommeneded as PCI core takes care of
that. Hence they became empty-body functions, thus define them NULL.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623094454.12427-1-vaibhavgupta40@gmail.com
In case of an error, no one will use the allocated structure. Call
ieee80211_free_hw, same as in rtl_usb_disconnect.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622132113.14508-4-code@reto-schneider.ch
Prevent code from calling itself indirectly, causing the driver to hang
and consume 100% CPU.
Without this fix, the following script can bring down a single CPU
system:
```
while true; do
rmmod rtl8192cu
modprobe rtl8192cu
done
```
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622132113.14508-2-code@reto-schneider.ch
Sparse reports the following issue:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: warning: incorrect type in initializer (different base types)
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: expected restricted __le32 [usertype] *pdesc
drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:500:26: got unsigned int [usertype] *
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604005733.7905-3-Larry.Finger@lwfinger.net
In some b43 files, the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-6-f.suligoi@asem.it
In at76c50x-usb.c the wiki url is still the old
"wireless.kernel.org" instead of the new
"wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-5-f.suligoi@asem.it
The wiki url is still the old "wireless.kernel.org"
instead of the new "wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605154112.16277-3-f.suligoi@asem.it
Add a set of logic with corresponding coexistence parameters to
handle the situation under BT inquiry/page.
We will set PSTDMA while WL-Busy + BT inquiry/page to separate
WL/BT slots. PSTDMA can protect WL data rate and BT performance.
If WL-Busy + BT inquiry/page and there was BT device paired,
We will set the mechanism to 4Slot PSTDMA.
In 4Slot PSTDMA, the paired devices can perform more smoothly
and prevent some issues trigger from insufficient data.
And to avoid A2DP glitch or disconnection, we will adjust ACL
data priority higher than inquiry/page.
In addition, we found sometimes BT inquiry/page still working
last for seconds after BT had notified inquiry/page finished.
It will lead to A2DP glitch cause of ACL data, inquiry/page
priority toggled. To fix the corner, we add a timer to remain
the inquiry/page status.
And we found WL busy/idle threshold is too sensitive,
it will keep switching in some weak network environment and
coexistence mechanism will switch between TDMA and PSTDMA.
The very frequently switching may destroyed not only the
handshake with AP, but BT performance. And it will trigger
some unexpected error.
To prevent the frequently switching, we add a timer to delay
the status change while WL busy switch to idle.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200715023324.8600-1-yhchuang@realtek.com
The length of the key comes from the network and it's a 16 bit number. It
needs to be capped to prevent a buffer overflow.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200708115857.GA13729@mwanda
ENOTSUPP (double PP) is internal linux kernel code 524 available only in
kernel include file linux/errno.h and not exported to userspace.
EOPNOTSUPP (OP; double PP) is standard code 95 for reporting 'operation not
supported' available via kernel include file uapi/asm-generic/errno.h.
ENOTSUP (single P) is alias for EOPNOTSUPP defined only in userspace
include file bits/errno.h and not available in kernel.
Because Linux kernel does not support ENOTSUP (single P) and because
userspace does not support ENOTSUPP (double PP), report error code for
'operation not supported' via EOPNOTSUPP macro.
This patch fixes problem that mwifiex kernel driver sends to userspace
unsupported error codes like: "failed: -524 (No error information)".
After applying this patch userspace see: "failed: -95 (Not supported)".
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200703112151.18917-1-pali@kernel.org
We currently have a collection of flags and locking between the
threaded irq and tx work:
- wl->flags bitops
- wl->mutex
- wl->wl_lock spinlock
The bitops flags do not need a spinlock around them, and we only need
the spinlock to see if we need to queue tx work or not. And wlcore_irq()
holds the mutex.
To simplify the locking, we can use spin_trylock and always queue tx
work unless we know there's nothing to do.
Let's also update the comment a bit while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-4-tony@atomide.com
We currently have a collection of flags and locking between the
threaded irq and tx work:
- wl->flags bitops
- wl->mutex
- wl->wl_lock spinlock
The bitops flags do not need a spinlock around them, and
wlcore_irq() already holds the mutex calling wlcore_irq_locked().
And we only need the spinlock to see if we need to run the queue
or not.
To simplify the locking, we can use spin_trylock and always run the
tx queue unless we know there's nothing to do.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-3-tony@atomide.com
We can simplify the runtime resume ELP path by always setting and
clearing the completion in runtime resume. This way we can test for
WL1271_FLAG_IRQ_RUNNING after the resume write to see if we need
completion at all.
And in wlcore_irq(), we need to take spinlock for running the
completion and for the pm_wakeup_event(). Spinlock is not needed
around the bitops flags check for WL1271_FLAG_SUSPENDED so the
spinlocked sections get shorter.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200702162951.45392-2-tony@atomide.com
This macro is already used in mwifiex driver for specifying upper limit and
is defined to value 3. So use it also in struct ieee80211_iface_limit.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200626152938.12737-1-pali@kernel.org
New device ID 0xc82f found on Lenovo ThinkCenter.
Tested it with c822 driver, works good.
PCI id:
03:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd.
Device [10ec:c82f]
Subsystem: Lenovo Device [17aa:c02f]
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200612082745.204400-1-aaron.ma@canonical.com
Some platforms cannot read the DBI register successfully for the
ASPM settings. After the read failed, the bus could be unstable,
and the device just became unavailable [1]. For those platforms,
the ASPM should be disabled. But as the ASPM can help the driver
to save the power consumption in power save mode, the ASPM is still
needed. So, add a module parameter for them to disable it, then
the device can still work, while others can benefit from the less
power consumption that brings by ASPM enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411
[2] Note that my lenovo T430 is the same.
Fixes: 3dff7c6e37 ("rtw88: allows to enable/disable HCI link PS mechanism")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605074703.32726-1-yhchuang@realtek.com
Since single rf path chips don't support TX SPBC, tell mac80211
to not advertise it.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-5-yhchuang@realtek.com
Beamforming is used for directional signal transmission/reception.
Beamformee plays the role for signal reception, and makes the RX
performance better in middle distance range.
Implement beamformee related callbacks for 8821c.
Since 8821c only support 1ss rate, nc_index in beamformee setting
needs to be adjusted based on the capability.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-4-yhchuang@realtek.com
The TX power requires to be adjusted based on the thermal value.
The actual power will decrease if the thermal value raised, and
will increase if the thermal value lowered. Driver comapres the
thermal value, as moving averages. If it changes over a limit,
driver will modify the TX power index to compensate.
Implement rtw_chip_ops::pwr_track() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-3-yhchuang@realtek.com
CCK PD can reduce the number of false alarm of the CCK rates.
It dynamically adjusts the power threshold and CS ratio.
The values are compared to the values of the previous level, if
the level is changed, set new values of power threshold and CS
ratio.
Implement rtw_chip_ops::cck_pd_set() for 8821c.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603094218.19942-2-yhchuang@realtek.com
In order to get a better TX EVM, do calibration after association.
The calibration needed for 8821c is the IQK, which is done in the
firmware. Implement the rtw_chip_ops::phy_calibration() to trigger
firmware to calibrate.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-8-yhchuang@realtek.com
False alarm statistics can be used to adjust the RX gain. This
helps the driver to adapt to different circumstances.
Implement rtw_chip_ops::false_alarm_statistics() for 8821c.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-7-yhchuang@realtek.com
Some RX packets contain also information about environment status.
Implement rtw_chip_ops::query_rx_desc() for 8821c. Parse the RX
descriptor which describes the current condition of the received
packet.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-6-yhchuang@realtek.com
8821c is capable of 2.4G and 5G.
Implement rtw_chip_ops::set_channel() to set 2G and 5G channels.
This includes MAC, BB and RF related settings.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-5-yhchuang@realtek.com
To improve user experience in field, we need DIG to adjust RX initial
gain depends on field situation.
Define the register addresses for 8821c.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-4-yhchuang@realtek.com
To configure the transmit power of 8821c implement trasmit
power index setting callback function for 8821c. This is very
similar to the callback function of 8822b.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-3-yhchuang@realtek.com
RTL8821CE chipsets are 802.11ac dual-band WiFi + BT combo chips.
This patch adds the basic functions such as parameter tables, chip
information, power on flow.
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616091625.26489-2-yhchuang@realtek.com
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type defining 'NETDEV_TX_OK' but this
driver returns '0' instead of 'NETDEV_TX_OK'.
Fix this by returning 'NETDEV_TX_OK' instead of '0'.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200629104009.84077-1-luc.vanoostenryck@gmail.com
Added version number info along with firmware name so driver can pick
the correct revision of FW file. Moved FW filename macro as part of
driver code & added MODULE_FIRMWARE to specify FW needed by module.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-6-ajay.kathat@microchip.com
Modify WILC1000 binary filename to use single unified wilc1000 FW.
A single wilc1000 binary is used for different wilc1000 revisions.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-5-ajay.kathat@microchip.com
Avoid below reported warning found when 'CONFIG_PM' config is
undefined.
'warning: unused variable 'wowlan_support' [-Wunused-const-variable]'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-4-ajay.kathat@microchip.com
Make use 'strlcpy' instead of 'strncpy' to overcome 'stringop-truncation'
compiler warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-3-ajay.kathat@microchip.com
As Adham's email address is bouncing, remove him from wilc1000 entry and
add Claudiu as a new co-maintainer. Claudiu follows wilc1000 driver
development for a long time and contributed to it already.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200710051826.3267-2-ajay.kathat@microchip.com
Xu Wang
Ping-Ke Shih
Joe Perches
Colin Ian King
Vaibhav Gupta
Reto Schneider
Kees Cook
Flavio Suligoi
Larry Finger
Zong-Zhe Yang
Dan Carpenter
Pali Rohár
Tony Lindgren
Yan-Hsuan Chuang
Aaron Ma
Tzu-En Huang
Luc Van Oostenryck
Ajay Singh
Nicolas Ferre