Previously, the caller would continue along without knowing that the
function failed, resulting in potential mis-rendering. Right now vm_fault
just returns SIGBUS in that case, and we may need to disable signal handling
to avoid that happening.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We'd love to just be using PAT, but even on chips with PAT it gets disabled
sometimes due to an errata. It would probably be better to have pat_enabled
exported and only bother with this when !pat_enabled.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This saves startup time from probing SDVO, and saves setting up HDMI outputs
on G4X devices that don't have them.
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI PM: make the PM core more careful with drivers using the new PM framework
PCI PM: Read power state from device after trying to change it on resume
PCI PM: Do not disable and enable bridges during suspend-resume
PCI: PCIe portdrv: Simplify suspend and resume
PCI PM: Fix saving of device state in pci_legacy_suspend
PCI PM: Check if the state has been saved before trying to restore it
PCI PM: Fix handling of devices without drivers
PCI: return error on failure to read PCI ROMs
PCI: properly clean up ASPM link state on device remove
Unfortunately, the OF device tree nodes for SBUS and PCI
hme devices have the same device node name on some systems.
So if the name of the parent node isn't 'sbus', skip it.
Based upon an excellent report and detective work by
Meelis Roos and Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Meelis Roos <mroos@linux.ee>
From: Ondrej Zary <linux@rainbow-software.org>
last year, I posted a patch which fixed hibernation on 3c509
cards. That was back in 2.6.24. It worked fine in 2.6.25. But then I
stopped using hibernation (as it did not work with my new IT8212 RAID
controller).
Now I fixed it and noticed that 3c509 does not wake up properly
anymore (in 2.6.28) - neither in PnP nor in ISA modes. ifconfig
down/up makes the card work again in PnP mode. However, in ISA mode,
ifconfig up ends with "No such device" error.
Comparing the 3c509 driver between 2.6.25 and 2.6.28, there's only
some statistics-related change. So the cause of the problem must be
somewhere else.
This patch makes the resume work in PnP mode, but it's still not
enough for ISA mode.
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Ilkka Virta <itvirta@iki.fi>
In the lockup situation the driver seems to go off in an eternal storm
of interrupts right after calling request_irq(). It doesn't actually
do anything interesting in the interrupt handler. Since connecting the link
afterwards works, something later in initialization must fix this.
Looking at gem_do_start() and gem_open(), it seems that the only thing
done while opening the device after the request_irq(), is a call to
napi_enable().
I don't know what the ordering requirements are for the
initialization, but I boldly tried to move the napi_enable() call
inside gem_do_start() before the link state is checked and interrupts
subsequently enabled, and it seems to work for me. Doesn't even break
anything too obvious...
Signed-off-by: David S. Miller <davem@davemloft.net>
During early boot, ACPI RSDT/XSDT table entries are gathered into the
'initial_tables[]' array. This array is currently statically defined (see
./drivers/acpi/tables.c). When there are more table entries than can be
held in the 'initial_tables[]' array, the message "Truncating N table
entries!" is output. As currently implemented, this message will always
erroneously calculate N as 0.
This patch fixes the calculation that determines how many table entries
will be missing (truncated).
This modification may be used under either the GPL or the BSD-style
license used for Intel ACPI CA code.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Some Realtek chips (RTL8169sb/8110sb in my case) are unable to retrieve
ethtool statistics when the interface is down. The process stays in
endless loop in rtl8169_get_ethtool_stats. This is because these chips
need to have receiver enabled (CmdRxEnb bit in ChipCmd register) that is
cleared when the interface is going down. It's better to update statistics
only when the interface is up and otherwise return copy of statistics
grabbed when the interface was up (in rtl8169_close).
It is interesting that PCI-E NICs (like 8168b/8111b...) are not affected.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the acpi subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some devices trigger a DEVICE_CHECK on every evalutation of _STA. This
can also be seen in commit 8b59560a3b
(ACPI: dock: avoid check _STA method). If an undock is processed, the
dock driver sends a uevent and userspace might read the show_docked
property in sysfs. This causes an evaluation of _STA of the particular
device which causes the dock driver to immediately dock again.
In any case, evaluation of _STA (show_docked) does not necessarily mean
that we are docked, so check with the internal device structure.
http://bugzilla.kernel.org/show_bug.cgi?id=12360
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
When ACPI is disabled in the BIOS of this VIA C3 box,
it invalidates the RSDP, which Linux notices:
ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080926]
Bug Linux neglected to disable ACPI at that stage,
and later scribbled on smp_found_config:
ACPI: No APIC-table, disabling MPS
But this box doesn't run well in legacy PIC mode,
it needed IOAPIC mode to perform correctly:
http://lkml.org/lkml/2009/2/5/39
So exit ACPI mode cleanly when we first detect
that it is hopeless.
Signed-off-by: Len Brown <len.brown@intel.com>
CPU_IDLE=y has been default for ACPI=y since Nov-2007,
and has shipped in many distributions since then.
Here we delete the CPU_IDLE=n ACPI idle code, since
nobody should be using it, and we don't want to
maintain two versions.
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: dv1394: move deprecation message from module init to file open
firewire: core: Remove card from list of cards when enable fails
* 'for-linus' of git://neil.brown.name/md:
md: Ensure an md array never has too many devices.
md: Fix a bug in linear.c causing which_dev() to return the wrong device.
md: Allow read error in a single drive raid1 to be passed up.
On many Linux installations, the dv1394 driver will be auto-loaded
whenever an AV/C device (e.g. camcorder or audio device) is plugged in.
An irritating message would then appear in the kernel log.
Defer this message to until a dv1394 character device file is actually
used by a program. Also include the program name in the message and
update the message slightly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Each different metadata format supported by md supports a
different maximum number of devices.
We really should be enforcing this maximum in the kernel, but
we aren't quite doing that properly.
We currently only enforce it at the 'hot_add' point, which is an
older interface which is not used by current userspace.
We need to also enforce it at 'add_new_disk' time for active arrays
and at 'do_md_run' time when starting a new array.
So move the test from 'hot_add' into 'bind_rdev_to_array' which is
called from both 'hot_add' and 'add_new_disk, and add a new
test in 'analyse_sbs' which is called from 'do_md_run'.
This bug (or missing feature) has been around "forever" and so
the patch is suitable for any -stable that is currently maintained.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
ab5bd5cbc8 introduced the following
bug in linear software raid for large arrays on 32 bit machines:
which_dev() computes the device holding a given sector by shifting
down the sector number to a 32 bit range, dividing by the array
spacing and looking up the resulting index in the hash table of
the array.
Because the computed index might be slightly too small, a loop at
the end of which_dev() increases the index until the given sector
actually falls into the range of the device associated with that index.
The changes of the above mentioned commit caused this loop to check
whether the _index_ rather than the sector number is small enough,
effectively bypassing the loop and thus possibly returning the wrong
device.
As reported by Simon Kirby, this leads to errors such as
linear_make_request: Sector 2340486136 out of bounds on dev sdi: 156301312 sectors, offset 2109870464
Fix this bug by introducing a local variable for the index so that
the variable containing the passed sector is left unchanged.
Cc: stable@kernel.org
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
If a raid1 only has a single working device and gets a read error,
we choose to simply return that error up to the filesystem (or whatever)
rather than failing the whole array.
However the codes doesn't quite do that. We attempt a readbalance
which allocates the same drive, so we retry the read - indefinitely.
Instead: If read_balance in the error case chooses the same drive that just
failed, treat it as a failure and don't retry.
Signed-off-by: NeilBrown <neilb@suse.de>
A missing type cast results in writing way beyond the end of a kzalloc()'d
memory segment resulting in slab corruption. But it seems like the better
solution is to define ->recv_msg_slots as a 'void *' rather than a
'struct xpc_notify_mq_msg_uv *' and add the type cast.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we return directly with -EPERM then lock_kernel() is still held.
This was found with a code checker (http://repo.or.cz/w/smatch.git/).
[akpm@linux-foundation.org: fix another such path - missed func_exit()]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: <R.E.Wolff@BitWizard.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix namespace violations by changing non-kconfig CONFIG_ names to CNFG_*.
Fixes breakage in staging/, which adds a real CONFIG_PANEL.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently both da903x backlight and voltage reulator drivers have the
same name. Rename the backlight driver to allow use of both drivers as
modules.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ssc pointer is not valid when the id is not found in the list.
Convert the message from a debug one into an error message and avoid
dereferencing the bad pointer.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6710x for having correctly setup
axes.
Signed-off-by: Martin Kebert <gkmarty@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6730x for having correctly setup
axes.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6530x for having correctly setup
axes.
Reported-by: Jerome Poulin <jeromepoulin@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to dmesg my laptop model HP 6510b is not being recognized by this
driver. After I have modified "lis3lv02d.c" axes in Neverball are OK.
Signed-off-by: Jiri Tersel <tersel@mail.muni.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The error-path code can call rfkill_unregister() with a pointer which does
not contain the result of a call to rfkill_register(). It goes BUG().
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12560.
Cc: Frans Pop <elendil@planet.nl>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Matthew Garrett <mjg@redhat.com>
Reported-by: Helge Deller <deller@gmx.de>
Testted-by: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid calling copy_from/to_user() with fb_info->lock mutex held in fbmem
ioctl().
fb_mmap() is called under mm->mmap_sem (A) held, that also acquires
fb_info->lock (B); fb_ioctl() takes fb_info->lock (B) and does
copy_from/to_user() that might acquire mm->mmap_sem (A), causing a
deadlock.
NOTE: it doesn't push down the fb_info->lock in each own driver's
fb_ioctl(), so there are still potential deadlocks elsewhere.
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple RTC driver for the MSP430 firmware on the DM355 EVM board. Other
than not supporting atomic reads/writes of all four bytes, this is
reasonable as a basic no-alarm RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dell-laptop makes use of the power supply class information to choose
which backlight interface to change. Add a depends on it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The device can take a while to respond to an open/close request, so
increase the time kernel will wait for response (1 ms to 10ms).
Also, properly clean up a channel on a failed open, by calling the channel
close routine. Just freeing the memory isn't sufficient, the device needs
to be informed that the channel is no longer open, and the device memory
cleared of references to freed dma buffer.
Signed-off-by: David Altobelli <david.altobelli@hp.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ondemand micro-accounting of idle time changes broke ignore_nice_load
sysfs setting due to a thinko in the code.
The bug entry:
http://bugzilla.kernel.org/show_bug.cgi?id=12310
Reported-by: Jim Bray <jimsantelmo@gmail.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Currently, the PM core always attempts to manage devices with drivers
that use the new PM framework. In particular, it attempts to disable
the devices (which is unnecessary), to save their state (which may be
undesirable if the driver has done that already) and to put them into
low power states (again, this may be undesirable if the driver has
already put the device into a low power state). That need not be
the right thing to do, so make the core be more careful in this
respect.
Generally, there are the following categories of devices to consider:
* bridge devices without drivers
* non-bridge devices without drivers
* bridge devices with drivers
* non-bridge devices with drivers
and each of them should be handled differently.
For bridge devices without drivers the PCI PM core will save their
state on suspend and restore it (early) during resume, after putting
them into D0 if necessary. It will not attempt to do anything else
to these devices.
For non-bridge devices without drivers the PCI PM core will disable
them and save their state on suspend. During resume, it will put
them into D0, if necessary, restore their state (early) and reenable
them.
For bridge devices with drivers the PCI PM core will only save
their state on suspend if the driver hasn't done that already.
Still, the core will restore their state (early) during resume,
after putting them into D0, if necessary.
For non-bridge devices with drivers the PCI PM core will only save
their state on suspend if the driver hasn't done that already. Also,
if the state of the device hasn't been saved by the driver, the core
will attempt to put the device into a low power state. During
resume the core will restore the state of the device (early), after
putting it into D0, if necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_restore_standard_config() unconditionally changes current_state
to PCI_D0 after attempting to change the device's power state, but
it should rather read the actual current power state from the
device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It is a mistake to disable and enable PCI bridges and PCI Express
ports during suspend-resume, at least at the time when it is
currently done. Disabling them may lead to problems with accessing
devices behind them and they should be automatically enabled when
their standard config spaces are restored. Fix this by not attempting
to disable bridges during suspend and enable them during resume.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Simplify suspend and resume of the PCI Express port driver. It no
longer needs to save and restore the standard configuration space of the
device; this is now done by the PCI PM core layer.
This patch is reported to fix the regression tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12598
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Parag Warudkar <parag.lkml@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make pci_legacy_suspend() save the state of the device if it is
in PCI_UNKNOWN after its suspend callback has run and warn only if
the power state of the device has been changed by its suspend
callback.
Also, use WARN_ONCE(), which is more useful, in pci_legacy_suspend(),
so that the name of the offending function is printed.
Additionally, remove the unnecessary line of code setting
pci_dev->state_saved.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Check if the standard configuration registers of a PCI device have
been saved during suspend before trying to restore them during
resume.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-By: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Suspend to RAM is reported to break on some machines as a result of
attempting to put one of driverless PCI devices into a low power
state. Avoid that by not attepmting to power manage driverless
devices during suspend.
Fix up pci_pm_poweroff() after a previous incomplete fix for the same
thing during hibernation.
This patch is reported to fix the regression from 2.6.28 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12605
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes the ROM reading code return an error to user space if
the size of the ROM read is equal to 0.
The patch also emits a warnings if the contents of the ROM are invalid,
and documents the effects of the "enable" file on ROM reading.
Signed-off-by: Timothy S. Nelson <wayland@wayland.id.au>
Acked-by: Alex Villacis-Lasso <a_villacis@palosanto.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We only want to disable ASPM when the last function is removed from
the parent's device list. We determine this by checking to see if
the parent's device list is completely empty.
Unfortunately, we never hit that code because the parent is considered
an upstream port, and never had an ASPM link_state associated with it.
The early check for !link_state causes us to return early, we never
discover that our device list is empty, and thus we never remove the
downstream ports' link_state nodes.
Instead of checking to see if the parent's device list is empty, we can
check to see if we are the last device on the list, and if so, then we
know that we can clean up properly.
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
SOFT_RESET must be asserted for at least 3 TX clocks in order for it to work
properly. The syncs in the gfar_write() commands have been hiding this, but
we need to guarantee it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BD_LENGTH_MASK is supposed to catch the low 16-bits of the status field, not
the low byte. The old way, we would never be able to clean up tx packets with
sizes divisible by 256.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LRO switch is always set to 1 in the rx processing loop.
It breaks the accelerated iSCSI receive traffic.
Fix its computation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.
Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MPC5200 PSC device is wired up to a dedicated interrupt line
which is never shared. This patch removes the IRQF_SHARED flag
from the request_irq() call which eliminates the "IRQF_DISABLED
is not guaranteed on shared IRQs" warning message from the console
output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
They were long enough set deprecated...
Update Documentation/cpu-freq/users-guide.txt:
The deprecated files listed there seen not to exist for some time anymore
already.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA exports acpi_os_validate_address() so the OS
can prevent BIOS AML from accessing specified addresses.
Start using this interface to prevent AML from accessing
some well known IO addresses that the OS "owns".
Signed-off-by: Len Brown <len.brown@intel.com>
The @fnac.net will be shut down within a couple of months, so fix my
email address.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On machine were no IO ports are assigned the call
to pci_enable_device() will fail, even if need_ioport
is false, we need to use pci_enable_device_mem() here.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch by Stephen Hemminger to convert XPNET to use net_device_ops and
internal net_device_stats failed to link the net_device_ops structure to the
net_device structure. See commit e8ac9c55f2
("xpnet: convert devices to new API").
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a few device ID's. It also removes an ID that was used
in an internal engineering version of a device and will never see
commercial light. Even if this ID will be 'recycled' in the future,
which is very unlikely, we don't know what kind of device will be
behind it. Therefore it's safer to remove it.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
on boot, print out the OSI strings the BIOS uses to query the OS.
To see this output...
build with CONFIG_ACPI_DEBUG
boot with
"acpi.debug_level=4" (ACPI_LV_INFO) (enabled by default)
and
"acpi.debug_level=1" (ACPI_UTILITIES) (default is 0)
example output:
ACPI: BIOS _OSI(Windows 2001) supported
ACPI: BIOS _OSI(Windows 2001 SP1) supported
ACPI: BIOS _OSI(Windows 2001 SP2) supported
ACPI: BIOS _OSI(Windows 2006) supported
ACPI: BIOS _OSI(Linux) not-supported
ACPI: BIOS _OSI(FreeBSD) not-supported
Signed-off-by: Len Brown <len.brown@intel.com>
There is no reason for the PSC UART driver or the Ethernet driver
to require a device_type property. The compatible value is sufficient
to uniquely identify the device. Remove it from the driver.
The whole 'port-number' scheme for assigning numbers to PSC uarts was
always rather half baked and just adds complexity. Remove it from the
driver. After this patch is applied, PSC UART numbers are simply
assigned from the order they are found in the device tree (just like
all the other devices). Userspace can query sysfs to determine what
ttyPSC number is assigned to each PSC instance.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement HORKAGE_1_5_GBPS and apply it to WD My Book
libata: add no penalty retry request for EH device handling routines
libata: improve probe failure handling
libata: add @spd_limit to sata_down_spd_limit()
libata: clear dev->ering in smarter way
libata: check onlineness before using SPD in sata_down_spd_limit()
libata: move ata_dev_disable() to libata-eh.c
libata: fix EH device failure handling
sata_nv: ck804 has borked hardreset too
ide/libata: fix ata_id_is_cfa() (take 4)
libata: fix kernel-doc warnings
ahci: add a module parameter to ignore the SSS flags for async scanning
sata_mv: Fix chip type for Hightpoint RocketRaid 1740/1742
[libata] sata_sil: Fix compilation error with libata debugging enabled
Change spin_locks to irqsave to prevent dead-locks.
Protect adding and deleting to/from dca_providers list.
Drop the lock during dca_sysfs_add_req() and dca_sysfs_remove_req() calls
as they might sleep (use GFP_KERNEL allocation).
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
while (limit--)
if (test())
break;
if (limit <= 0)
goto test_failed;
In the last iteration, limit is decremented after the test to 0.
If just thereafter test() succeeds and a break occurs, the goto
still occurs because limit is 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
while (timeout--) { ... }
timeout becomes -1 if the loop isn't ended otherwise, not 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3Gbps is often much more prone to transmission failures. It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them. Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.
This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.
Please take a look at the following bz for related reports.
http://bugzilla.kernel.org/show_bug.cgi?id=9913
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Let -EAGAIN from EH device handling routines trigger EH retry without
consuming its tries count. This will be used to implement link SPD
horkage which requires hardreset to adjust SPD without affecting other
EH decisions. As it bypasses the forward progress guarantee provided
by the tries count, the requester is responsible for ensuring forward
progress.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When link is flaky at high speed, it isn't uncommon for a device to
repeatedly fail probing sequence early after successfully negotiating
high link speed. This often leads to consecutive hotplug events
without successful probing.
This patch improves libata EH such that it remembers probing trials
and if there have been more than two unsuccessful trials in the past
60 seconds, slows down link speed to 1.5Gbps.
As link speed negotiation is the duty of the PHY layer proper, the
goal of this fallback mechanism is to provide the last resort when
everything else fails, which unfortunately happens not too
infrequently, so no fancy 6->3->1.5 speeding down or highest
successful transmission speed seen kind of logics (yet).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants. This parameter doesn't get in the way even
when it's too low. The closest possible limit is applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events. This patch
achieves this by doing the following.
* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
clear between BEGIN and END. ering is moved after END. The split
of persistent area is to allow hotter items remain at the head.
* ering is explicitly cleared on ata_dev_disable() and when device
attach succeeds. So, ering is persistent throug a device's life
time (unless explicitly cleared of course) and also through periods
inbetween disablement of an attached device and successful detection
of the next one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_down_spd_limit() should check whether the link is online before
using the SPD value to determine how to limit the link speed. Factor
out onlineness test and test it from sata_down_spd_limit().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_dev_disable() is about to be more tightly integrated into EH
logic. Move it to libata-eh.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dev->pio_mode > XFER_PIO_0 test is there to avoid unnecessary
speed down warning messages but it accidentally disabled SATA link spd
down during configuration phase after reset where PIO mode is always
zero.
This patch fixes the problem by moving the test where it belongs.
This makes libata probing sequence behave better when the connection
is flaky at higher link speeds which isn't too uncommon for eSATA
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While playing with nvraid, I found out that rmmoding and insmoding
often trigger hardreset failure on the first port (the second one was
always okay). Seriously, how diverse can you get with hardreset
behaviors? Anyways, make ck804 use noclassify variant too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata kernel-doc warnings:
Warning(linux-next-20090120//drivers/ata/libata-core.c:4720): Excess function parameter 'dev' description in 'ata_qc_new'
Warning(linux-next-20090120//drivers/ata/libata-scsi.c:428): No description found for parameter 'ap'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SSS flag, which directs the OS to spin up one disk at a time
to not have the PSU blow out, sometimes gets set even when not needed.
The effect of this is a longer-than-needed boot time.
This patch adds a module parameter that makes the driver ignore SSS
at least as far as the parallel scan during boot is concerned...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix chip type for the Highpoint RocketRAID 1740 and 1742 PCI cards.
These really do have Marvell 6042 chips on them, rather than the 5081 chip.
Confirmed by multiple (two) users (for the 1740), and by examining
the product photographs from Highpoint's web site.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I tried compiling 2.6.29-rc1 and 2.6.29-rc3 with libata debugging enabled
and got the following error:
CC [M] drivers/ata/sata_sil.o
drivers/ata/sata_sil.c: In function 'sil_fill_sg':
drivers/ata/sata_sil.c:327: error: 'pi' undeclared (first use in this function)
drivers/ata/sata_sil.c:327: error: (Each undeclared identifier is reported only once
drivers/ata/sata_sil.c:327: error: for each function it appears in.)
make[2]: *** [drivers/ata/sata_sil.o] Error 1
make[1]: *** [drivers/ata] Error 2
make: *** [drivers] Error 2
include/linux/libata.h has the following enabled:
#define ATA_DEBUG
#define ATA_VERBOSE_DEBUG
#define ATA_IRQ_TRAP
This fixes the compilation.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to the Spec the first two elements in the _BCL package won't be
regarded as the available brightness level. The first is the brightness when
full power is connected to the box(It means that the AC adapter is plugged).
The second is the brightness level when the box is on battery.
If the first two elements are still used while finding the next brightness
level, it will fall back to the lowest level when keeping on pressing
hotkey. (On some boxes the brightness will be changed twice when hotkey is
pressed once. One is in the ACPI video driver. The other is changed by sys I/F.
In the ACPI video driver the first two elements will be used while changing
the brightness. But the first two elements is skipped while using sys I/F.
In such case there exists the inconsistency).
So he first two elements had better be skipped while showing the available
brightness or finding the next brightness level.
http://bugzilla.kernel.org/show_bug.cgi?id=12450
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: enable DMA for write ops after CMD/RESP
pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
ricoh_mmc: Use suspend_late/resume_early
mmci: Add support for ST Micro derivate
mmc: Add a MX2/MX3 specific SDHC driver
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
icside: fix PCB version 6 support (v2)
tx4939ide: typo fix and minor cleanup
ide: add CS5536 host driver (v3)
ide: Force VIA IDE legacy interrupts for AmigaOne boards
IDE: Unregister and disable devices if initialization fails.
ide: fix ide_register_port() failure handling
ide: struct device - replace bus_id with dev_name(), dev_set_name()
ide-cd: fix DMA for non bio-backed requests
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: lock rc->rsvs_lock with spin_lock_bh()
wusb: timeout when waiting for ASL/PZL updates in whci-hcd
uwb: remove unused #include <version.h>'s
wusb: return -ENOTCONN when resetting a port with no connected device
uwb: safely remove all reservations
The host really shouldn't be notifying us of config changes
before the device status is VIRTIO_CONFIG_S_DRIVER or
VIRTIO_CONFIG_S_DRIVER_OK.
However, if we do happen to be interrupted while we're not
attached to a driver, we really shouldn't oops. Prevent
this simply by checking that device->driver is non-NULL
before trying to notify the driver of config changes.
Problem observed by doing a "set_link virtio.0 down" with
QEMU before the net driver had been loaded.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this the 2nd port gets first ports MAC addr.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Anholt
Dave Airlie
Linus Torvalds
David S. Miller
Len Brown
Thierry Vignaud
Ondrej Zary
Darren Salt
Ilkka Virta
Myron Stowe
Ivan Vecera
Kay Sievers
Frank Seidel
Holger Macht
Stefan Richter
NeilBrown
Andre Noll
Dean Nelson
Dan Carpenter
Randy Dunlap
Manish Katiyar
Mike Rapoport
Hans-Christian Egtvedt
Martin Kebert
Pavel Herrmann
Eric Piel
Jiri Tersel
Andrew Morton
Andrea Righi
David Brownell
Matthew Garrett
David Altobelli
Venkatesh Pallipadi
Rafael J. Wysocki
Timothy S. Nelson
Alex Chiang
Andy Fleming
Divy Le Ray
Reinette Chatre
Grant Likely
Thomas Renninger
Samuel Thibault
Karsten Keil
Cord Walter
Filip Aben
Dave Airlie
Maciej Sosnowski
Roel Kluin
Tejun Heo
Zhao Yakui
Arjan van de Ven
Mark Lord
Pasi Kärkkäinen
Mark McLoughlin
Ron Mercer