Based almost entirely upon a patch by Eric Dumazet.
The common case is to have num-tx-queues <= num_rx_queues
and even if num_tx_queues is larger it will not be significantly
larger.
Therefore, a subtraction loop is always going to be faster than
modulus.
Signed-off-by: David S. Miller <davem@davemloft.net>
Spotted a tiny ugliness in a recently posted patch. This patch cuts it out.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/ne2k-pci.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing it in reverse order causes uevent to be sent before
we have a MAC address, which confuses udev.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ba25ff4c6 ("br2684: convert to
net_device_ops") inadvertently deleted the initialization of the net_dev
pointer in the br2684_dev structure, leading to crashes. This patch
adds it back.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel should only be using the high 16 bits of a kernel
generated priority. Filter priorities in all other cases only
use the upper 16 bits of the u32 'prio' field of 'struct tcf_proto',
but when the kernel generates the priority of a filter is saves all
32 bits which can result in incorrect lookup failures when a filter
needs to be deleted or modified.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were avoiding calling sg_init* on scatterlists passed
into virtnet_send_command to prevent extraneous end markers.
This caused build warnings for uninitialized variables.
Cleanup the code to create proper scatterlists.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c589_cs,3c574_cs,serial_cs:
(1)add cis(firmware) of 3Com lan&modem mulitifunction pcmcia card.
(2)load correct configuration register for 3Com card
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the cleanup in bond_create nicer :) Also now the forgotten
free_netdev is called.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio_net.h uses the macro ETH_ALEN which is defined in linux/if_ether.h.
Discovered when hacking on virtio-over-pci patches.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new logic to support a clock gating feature found on the
latest set of chipsets. The clock gating is performed on the tx/rx
engines when the link is disconnected. Clock gating helps in reducing
power consumption.
* modified based on comments from netdev
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAN9512 and LAN9514 are USB hubs with an integrated 10/100 ethernet
controller. Logically this looks like an ethernet controller (similar
to LAN9500) permanently attached to one of the hub's downstream ports.
This patch adds the usb device id of the new ethernet controller to the
smsc95xx driver. This id is the same in both new devices.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMSC LAN9500 has dual purpose GPIO/LED pins, and by default at power-on
these are configured as GPIOs. This means that if LEDs are fitted they
won't ever light.
This patch sets them to be LED outputs for speed, duplex and
link/activity.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netconsole is loaded and a network interface fades away (e.g. on
rmmod $interface_driver_module) the rmmod remains stuck and some locks
are taken that prevent any additional module loading/unloading as well
as interface up/down changes.
In addition kernel logs (and console) get flooded at 10s interval with
[ 122.464065] unregister_netdevice: waiting for eth0 to become free. Usage count = 1
[ 132.704059] unregister_netdevice: waiting for eth0 to become free. Usage count = 1
This patch lets netconsole take NETDEV_UNREGISTER event into account
and release the affected interface if it was in use.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_socket can use connection tracking, and checks whether it is a module.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_slave_info_query() should keep a read lock while accessing slave info,
or risk accessing stale data and corruption.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial: fixing gcc 4.4 compiler warning:
drivers/net/cxgb3/t3_hw.c: In function ‘t3_prep_adapter’:
drivers/net/cxgb3/t3_hw.c:3782: warning: suggest parentheses around operand of ‘!’ or change ‘|’ to ‘||’ or ‘!’ to ‘~’
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb_rx_queue_recorded() is true, we dont want to use jash distribution
as the device driver exactly told us which queue was selected at RX time.
jhash makes a statistical shuffle, but this wont work with 8 static inputs.
Later improvements would be to compute reciprocal value of real_num_tx_queues
to avoid a divide here. But this computation should be done once,
when real_num_tx_queues is set. This needs a separate patch, and a new
field in struct net_device.
Reported-by: Andrew Dickinson <andrew@whydna.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek wrote:
> Since 4fb6699481 ("net: Optimize memory
> usage when splicing from sockets.") I'm seeing this oops (e.g. in
> 2.6.30-rc3) when splicing from a TCP socket to /dev/null on a driver
> (mv643xx_eth) that uses LRO in the skb mode (lro_receive_skb) rather
> than the frag mode:
My patch incorrectly assumed skb->sk was always valid, but for
"frag_listed" skbs we can only use skb->sk of their parent.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Debugged-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 011983048a.
Causes warnings in the build as reported by Stephen Rothwell.
So this change is worse than what it's curing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignore link partner advertising flags while AN is not complete.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mdio_support and lp_advertising fields to ethtool_cmd. Set these
in mdio45_ethtool_gset{,_npage}().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the ETHTOOL_SPAUSEPARAM operation for MDIO (clause 45)
PHYs with auto-negotiation MMDs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts flow control capabilites to an advertising mask and can
be useful in combination with mii_resolve_flowctrl_fdx().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a shorter and more comprehensible formulation of the
conditions for each flow control mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.
Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These roughly mirror many of the MII library functions and are based
on code from the sfc driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3 clause 45 specifies the MDIO interface and registers for
use in 10G and other PHYs, similar to the MII management interface.
PHYs may have up to 32 MMDs corresponding to different sub-layers and
functions, each with up to 65536 registers. These are addressed by
PRTAD (similar to the MII PHY address) and DEVAD. Define a mapping
for specifying PRTAD and DEVAD through the existing MII ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PORT_OTHER to represent all other physical port types. Current
NICs generally do not allow switching between multiple port types in
software so specific types should not be needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On several mv643xx_eth hardware versions, the two 64bit mib counters
for 'good octets received' and 'good octets sent' are actually 32bit
counters, and reading from the upper half of the register has the same
effect as reading from the lower half of the register: an atomic
read-and-clear of the entire 32bit counter value. This can under heavy
traffic occasionally lead to small numbers being added to the upper
half of the 64bit mib counter even though no 32bit wrap has occured.
Since we poll the mib counters at least every 30 seconds anyway, we
might as well just skip the reads of the upper halves of the hardware
counters without breaking the stats, which this patch does.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when OOM occurs during rx ring refill, mv643xx_eth will get
into an infinite loop, due to the refill function setting the OOM bit
but not clearing the 'rx refill needed' bit for this queue, while the
calling function (the NAPI poll handler) will call the refill function
in a loop until the 'rx refill needed' bit goes off, without checking
the OOM bit.
This patch fixes this by checking the OOM bit in the NAPI poll handler
before attempting to do rx refill. This means that once OOM occurs,
we won't try to do any memory allocations again until the next invocation
of the poll handler.
While we're at it, change the OOM flag to be a single bit instead of
one bit per receive queue since OOM is a system state rather than a
per-queue state, and cancel the OOM timer on entry to the NAPI poll
handler if it's running to prevent it from firing when we've already
come out of OOM.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
These two memory barriers in performance-critical paths are not needed
on x86. Even if some other architecture does buffer PCI I/O space
writes, the existing memory-mapped I/O barriers are unlikely to be what
is needed.
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In "mac80211: correct wext transmit power handler"
I fixed the wext handler, but forgot to make the default of the
user_power_level -1 (aka "auto"), so that now the transmit power
is always set to 0, causing associations to time out and similar
problems since we're transmitting with very little power. Correct
this by correcting the default user_power_level to -1.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Bisected-by: Niel Lambrechts <niel.lambrechts@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- ieee80211_wep_init(), which is called with rtnl_lock held, blocks in
request_module() [waiting for modprobe to load a crypto module].
- modprobe blocks in a call to flush_workqueue(), when it closes a TTY
[presumably when it exits].
- The workqueue item linkwatch_event() blocks on rtnl_lock.
There's no reason for wep_init() to be called with rtnl_lock held, so
just move it outside the critical section.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were calling pci_enable_wake() twice in a row for both D3_hot
and D3_cold. This replaces those calls with a call to pci_wake_from_d3()
to avoid issues with PCI PM vs ordering constraints.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o hold the firmware in memory across suspend, since filesystem
may not be up after resuming.
o reset the chip after requesting firmware, to minimize downtime
for NC-SI.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Rami Rosen
Jiri Pirko
Lubomir Rintel
Rabin Vincent
Robert Love
Alex Williamson
Ken Kawasaki
Grant Likely
Ayaz Abdulla
Steve Glendinning
Bruno Prémont
Laszlo Attila Toth
Greg Kroah-Hartman
Eric Dumazet
Sergey Senozhatsky
Jarek Poplawski
Ben Hutchings
Lennert Buytenhek
John Dykstra
Johannes Berg
Alan Jenkins
Don Skidmore
Dhananjay Phadke