Lee Schermerhorn reported that he saw bad pointer dereference in
mem_cgroup_end_migration() when he disabled memcg by boot option.
memcg's page migration logic works as
mem_cgroup_prepare_migration(page, &ptr);
do page migration
mem_cgroup_end_migration(page, ptr);
Now, ptr is not initialized in prepare_migration when memcg is disabled
by boot option. This causes panic in end_migration. This patch fixes it.
Reported-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix wrong bit mask for blanking register. Due to the error a CRT monitor
blanks off due to wrong frequency (out of range) instead of PM signal
(vertical and horizontal frequencies cut off).
Just compare the mask with bits set in the switch(blank) clause below the
changed line.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove fb_save_state() and fb_restore_state operations from frame buffer layer.
They are used only in two drivers:
1. savagefb - and cause bug #11248
2. uvesafb
Usage of these operations is misunderstood in both drivers so kill these
operations, fix the bug #11248 and avoid confusion in the future.
Tested on Savage 3D/MV card and the patch fixes the bug #11248.
The frame buffer layer uses these funtions during switch between graphics
and text mode of the console, but these drivers saves state before
switching of the frame buffer (in the fb_open) and after releasing it (in
the fb_release). This defeats the purpose of these operations.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11248
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Jochen Hein <jochen@jochen.org>
Tested-by: Jochen Hein <jochen@jochen.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 341ce06f69 ("page allocator:
calculate the alloc_flags for allocation only once") altered watermark
logic slightly by allowing rt_tasks that are handling an interrupt to set
ALLOC_HARDER. This patch brings the watermark logic more in line with
2.6.30.
This change results in a reduction of the number high-order GFP_ATOMIC
allocation failures reported. See
http://www.gossamer-threads.com/lists/linux/kernel/1144153
[rientjes@google.com: Spotted the problem]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a direct reclaim makes no forward progress, it considers whether it
should go OOM or not. Whether OOM is triggered or not, it may retry the
allocation afterwards. In times past, this would always wake kswapd as
well but currently, kswapd is not woken up after direct reclaim fails.
For order-0 allocations, this makes little difference but if there is a
heavy mix of higher-order allocations that direct reclaim is failing for,
it might mean that kswapd is not rewoken for higher orders as much as it
did previously.
This patch wakes up kswapd when an allocation is being retried after a
direct reclaim failure. It would be expected that kswapd is already
awake, but this has the effect of telling kswapd to reclaim at the higher
order as well.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
openipmi list is moderated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the `s' it just won't work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Names with periods or commas need to be quoted
Use tab not spaces
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Integrate P:/M: lines to single M:
Use tabs not spaces
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Integrate P:/M: to single M:
Use tab for spacing
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jing Huang <huangj@brocade.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oops. How did that get there?
(Don't look, it's my original pattern commit...)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BugLink: https://bugs.launchpad.net/bugs/462098
Until we can look closer at the verbs, let's use ALC885_MB5 for
codec SSID 0x106b4600 to enable playback and capture for MacBookPro
5,2s.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Export is needed for modular builds, and a static inline stub is needed
for non-MPC83xx builds.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add power management controller nodes and sleep properties.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds needed nodes and properties to support suspend/resume
on the MPC8610HPCD boards.
There is a dedicated switch (SW9) that is used to wake up the boards.
By default the SW9 button is routed to IRQ8, but could be re-routed
(via PIXIS) to sreset.
With 'no_console_suspend' kernel command line argument specified, the
board is also able to wakeup upon serial port input.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com> [dts]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add power management controller nodes;
- Add interrupts for RTC nodes, the RTC interrupt may be used as a
wakeup source;
- Add sleep properties (DEVDISR bit mask) and sleep-nexus nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds suspend/resume support for MPC8540 and MPC8641D-
compatible CPUs. To reach sleep state, we just write the SLP bit
into the PM control and status register.
So far we don't support Deep Sleep mode as found in newer MPC85xx
CPUs (i.e. MPC8536). It can be relatively easy implemented though,
and for it we reserve 'mem' suspend type.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
So far the driver is used to reset QE upon resume, which is needed on
85xx. Later we can move some QE initialization steps into probe().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds QE buffer descriptors mode support for the
spi_mpc8xxx driver, and as a side effect we now support CPM1
and CPM2 SPI controllers.
That means that today we support almost all MPC SPI controllers:
- MPC834x-style controllers (support PIO mode only);
- CPM1 and CPM2 controllers (support DMA mode only);
- QE SPI controllers in CPU mode (PIO mode with shift quirks);
- QE SPI controllers in buffer descriptors (DMA) mode;
The only controller we don't currently support is a newer eSPI
(with a dedicated chip selects and a bit different registers map).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Soon there will be more flags introduced in subsequent patches, so
let's turn qe_mode into flags.
Also introduce mpc8xxx_spi_strmode() and print current SPI mode.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We'll add more steps soon, so get rid of the duplication.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes the following warning:
CC drivers/spi/spi_mpc8xxx.o
spi_mpc8xxx.c: In function 'of_mpc8xxx_spi_probe':
spi_mpc8xxx.c:681: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to avoid ugly #ifdefs in drivers. Also update fsl_qe_udc
driver so that now it doesn't define its own versions that cause build
breakage when the generic stubs are used.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The bits are generic to CPM devices, so let's move them to the
common header file, so drivers won't need to privately reintroduce
another bunch of the same bits (as we can't include cpm2.h header
together with cpm1.h).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
struct mcc defined in both immap_qe.h and immap_cpm2.h, so they will
conflic when included in a single file. The mcc struct is easy to deal
with, since it isn't used in any driver (yet), so let's just rename QE
version to qe_mcc.
The ucb_ctlr is a bit trickier, since it is used by fsl_qe_udc driver,
and the driver supports both CPM and QE UDCs, plus the QE version is
used to form a bigger immap struct.
I don't want to touch too much of USB code in this series, so for now
let's just copy most generic version into the common cpm.h header,
later we'll create cpm_usb.h where we'll place common USB structs that
are used by QE/CPM UDC and QE Host drivers (FHCI).
And as for the structs in qe.h and cpm2.h, just prefix them with qe_
and cpm_.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When cpm2.h included into spi_mpc8xxx driver, the SPI defines
in the header conflict with defines in the driver.
We don't need them in the header file, so remove them. Plus
remove "struct spi", we'll use a better version in the driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020 is another member of Freescale QorIQ series of processors.
It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences from P2020:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities(new controller).
From board perspective P1020RDB is same as P2020RDB.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It appears that QE shuts down on all MPC85xx CPUs (i.e. MPC8568 and
MPC8569) and thus needs reset upon resume.
So modify qe_alive_during_sleep() to account that.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For MPC8569 CPUs we'll need to reset QE after each suspend, so make
qe_reset() code path suitable for repeated invocation, that is:
- Don't initialize rheap structures if already initialized;
- Don't allocate muram for SDMA if already allocated, just reinitialize
registers with previously allocated muram offset;
- Remove __init attributes from qe_reset() and cpm_muram_init();
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch creates the dts files for each core and splits the devices
between the two cores for P2020RDB.
core0 has memory, L2, i2c, spi, dma1, usb, eth0, eth1, crypto,
global-util, pci0,
core1 has L2, dma2, eth0, pci1, msi.
MPIC is shared between two cores but each core will protect its
interrupts from other core by using "protected-sources" of mpic.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to avoid #ifdefs in MPC85xx suspend/resume code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8569 CPUs have four QE RISCs, so we need to increase MAX_QE_RISC
constant, otherwise qe_upload_firmware() fails at sanity checking.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To support PCIe hot plug in IOMMU, we register a notifier to respond to device
change action.
When the notifier gets BUS_NOTIFY_UNBOUND_DRIVER, it removes the device
from its DMAR domain.
A hot added device will be added into an IOMMU domain when it first does IOMMU
op. So there is no need to add more code for hot add.
Without the patch, after a hot-remove, a hot-added device on the same
slot will not work.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The model for IOMMU passthrough is that decent devices that can cope
with DMA to all of memory get passthrough; crappy devices with a limited
dma_mask don't -- they get to use the IOMMU anyway.
This is done on the basis that IOMMU passthrough is usually wanted for
performance reasons, and it's only the decent PCI devices that you
really care about performance for, while the crappy 32-bit ones like
your USB controller can just use the IOMMU and you won't really care.
Unfortunately, the check for this was only looking at dev->dma_mask, not
at dev->coherent_dma_mask. And some devices have a 32-bit
coherent_dma_mask even though they have a full 64-bit dma_mask.
Even more unfortunately, fixing that simple oversight would upset
certain broken HP devices. Not only do they have a 32-bit
coherent_dma_mask, but they also have a tendency to do stray DMA to
unmapped addresses. And then they die when they take the DMA fault they
so richly deserve.
So if we do the 'correct' fix, it'll mean that affected users have to
disable IOMMU support completely on "a large percentage of servers from
a major vendor."
Personally, I have little sympathy -- given that this is the _same_
'major vendor' who is shipping machines which claim to have IOMMU
support but have obviously never _once_ booted a VT-d capable OS to do
any form of QA. But strictly speaking, it _would_ be a regression even
though it only ever worked by fluke.
For 2.6.33, we'll come up with a quirk which gives swiotlb support
for this particular device, and other devices with an inadequate
coherent_dma_mask will just get normal IOMMU mapping.
The simplest fix for 2.6.32, though, is just to jump through some hoops
to try to allocate coherent DMA memory for such devices in a place that
they can reach. We'd use dma_generic_alloc_coherent() for this if it
existed on IA64.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Each device has its own 'recovery_offset' showing how far
recovery has progressed on the device.
As the only real significance of this is that fact that it can
be stored in the metadata and recovered at restart, and as
only 1.x metadata can do this, we were only updating
'recovery_offset' to 'curr_resync_completed' when updating
v1.x metadata.
But this is wrong, and we will shortly make limited use of this
field in v0.90 metadata.
So move the update into common code.
Signed-off-by: NeilBrown <neilb@suse.de>
Adjust OMAP3 frequency transition latency from 10,000,000uS to a more
reasonable 300,000uS. This causes ondemand and conservative governors to
sample CPU load more often resulting in more responsive behavior.
Tested on Android 2.6.29; using this value and conservative governor, CORE
power consumption on Zoom2 was comparable to the old and unresponsive
10,000,000uS value while UI responsiveness was greatly improved.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix panic when trying to destroy a newly allocated
Btrfs: allow more metadata chunk preallocation
Btrfs: fallback on uncompressed io if compressed io fails
Btrfs: find ideal block group for caching
Btrfs: avoid null deref in unpin_extent_cache()
Btrfs: skip btrfs_release_path in btrfs_update_root and btrfs_del_root
Btrfs: fix some metadata enospc issues
Btrfs: fix how we set max_size for free space clusters
Btrfs: cleanup transaction starting and fix journal_info usage
Btrfs: fix data allocation hint start
Rafael debugged a resume-time hang (with oopses in workqueue handling)
on his laptop that was due to the 'waker' workqueue entry being
disconnected and then released without the workqueue entry having been
synchronized.
Several people were involved, with Oleg Nesterov doing a debugging patch
showing what workqueue entry was corrupt etc.
This was a regression introduced by commit 7bee549e19 ("Bluetooth: Add
USB autosuspend support to btusb driver") as Rafael points out (not
actually bisected, but it became clear once the bug was found).
Tested-and-reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a problem where iget5_locked will look for an inode, not find it, and
then subsequently try to allocate it. Another CPU will have raced in and
allocated the inode instead, so when iget5_locked gets the inode spin lock again
and does a search, it finds the new inode. So it goes ahead and calls
destroy_inode on the inode it just allocated. The problem is we don't set
BTRFS_I(inode)->root until the new inode is completely initialized. This patch
makes us set root to NULL when alloc'ing a new inode, so when we get to
btrfs_destroy_inode and we see that root is NULL we can just free up the memory
and continue on. This fixes the panic
http://www.kerneloops.org/submitresult.php?number=812690
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
JBD/JBD2: free j_wbuf if journal init fails.
ext3: Wait for proper transaction commit on fsync
ext3: retry failed direct IO allocations
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: Adjust GFP mask handling for coherent allocations
PCI ASPM: fix oops on root port removal
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: pasemi_defconfig update
powerpc: 2.6.32 update of defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx
powerpc/8xxx: enable IPsec ESP by default on mpc83xx/mpc85xx
powerpc/83xx: Fix u-boot partion size for MPC8377E-WLAN boards
powerpc/85xx: Fix USB GPIOs for MPC8569E-MDS boards
powerpc/82xx: kmalloc failure ignored in ep8248e_mdio_probe()
powerpc/85xx: sbc8548 - fixup of PCI-e related DTS fields
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (52 commits)
drm/kms: Init the CRTC info fields for modes forced from the command line.
drm/radeon/r600: CS parser updates
drm/radeon/kms: add debugfs for power management for AtomBIOS devices
drm/radeon/kms: initial mode validation support
drm/radeon/kms/atom/dce3: call transmitter init on mode set
drm/radeon/kms: store detailed connector info
drm/radeon/kms/atom/dce3: fix up usPixelClock calculation for Transmitter tables
drm/radeon/kms/r600: fix rs880 support v2
drm/radeon/kms/r700: fix some typos in chip init
drm/radeon/kms: remove some misleading debugging output
drm/radeon/kms: stop putting VRAM at 0 in MC space on r600s.
drm/radeon/kms: disable D1VGA and D2VGA if enabled
drm/radeon/kms: Don't RMW CP_RB_CNTL
drm/radeon/kms: fix coherency issues on AGP cards.
drm/radeon/kms: fix rc410 suspend/resume.
drm/radeon/kms: add quirk for hp dc5750
drm/radeon/kms/atom: fix potential oops in spread spectrum code
drm/kms: typo fix
drm/radeon/kms/atom: Make card_info per device
drm/radeon/kms/atom: Fix DVO support
...
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
highmem: Fix debug_kmap_atomic() to also handle KM_IRQ_PTE, KM_NMI, and KM_NMI_PTE
highmem: Fix race in debug_kmap_atomic() which could cause warn_count to underflow
rcu: Fix long-grace-period race between forcing and initialization
uids: Prevent tear down race
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix permission checks
perf_events: Fix some typo in the perf events config description
KAMEZAWA Hiroyuki
Krzysztof Helt
Mel Gorman
Randy Dunlap
Roel Kluin
Joe Perches
Stefan Schmidt
Daniel T Chen
Anton Vorontsov
Poonam Aggrwal
Fenghua Yu
Alex Williamson
NeilBrown
Benjamin Herrenschmidt
Mike Turquette
Linus Torvalds
Josef Bacik