gdbserver inserting a breakpoint ends up calling copy_user_page() for a
code page. The generic version of which (non-aliasing config) didn't set
the PG_arch_1 bit hence update_mmu_cache() didn't sync dcache/icache for
corresponding dynamic loader code page - causing garbade to be executed.
So now aliasing versions of copy_user_highpage()/clear_page() are made
default. There is no significant overhead since all of special alias
handling code is compiled out for non-aliasing build
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The VM_EXEC check in update_mmu_cache() was getting optimized away
because of a stupid error in definition of macro addr_not_cache_congruent()
The intention was to have the equivalent of following:
if (a || (1 ? b : 0))
but we ended up with following:
if (a || 1 ? b : 0)
And because precedence of '||' is more that that of '?', gcc was optimizing
away evaluation of <a>
Nasty Repercussions:
1. For non-aliasing configs it would mean some extraneous dcache flushes
for non-code pages if U/K mappings were not congruent.
2. For aliasing config, some needed dcache flush for code pages might
be missed if U/K mappings were congruent.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This manifested as grep failing psuedo-randomly:
-------------->8---------------------
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$
[ARCLinux]$ ip address show lo | grep inet
inet 127.0.0.1/8 scope host lo
-------------->8---------------------
ARC700 MMU provides fully orthogonal permission bits per page:
Ur, Uw, Ux, Kr, Kw, Kx
The user mode page permission templates used to have all Kernel mode
access bits enabled.
This caused a tricky race condition observed with uClibc buffered file
read and UNIX pipes.
1. Read access to an anon mapped page in libc .bss: write-protected
zero_page mapped: TLB Entry installed with Ur + K[rwx]
2. grep calls libc:getc() -> buffered read layer calls read(2) with the
internal read buffer in same .bss page.
The read() call is on STDIN which has been redirected to a pipe.
read(2) => sys_read() => pipe_read() => copy_to_user()
3. Since page has Kernel-write permission (despite being user-mode
write-protected), copy_to_user() suceeds w/o taking a MMU TLB-Miss
Exception (page-fault for ARC). core-MM is unaware that kernel
erroneously wrote to the reserved read-only zero-page (BUG #1)
4. Control returns to userspace which now does a write to same .bss page
Since Linux MM is not aware that page has been modified by kernel, it
simply reassigns a new writable zero-init page to mapping, loosing the
prior write by kernel - effectively zero'ing out the libc read buffer
under the hood - hence grep doesn't see right data (BUG #2)
The fix is to make all kernel-mode access permissions mirror the
user-mode ones. Note that the kernel still has full access to pages,
when accessed directly (w/o MMU) - this fix ensures that kernel-mode
access in copy_to_from() path uses the same faulting access model as for
pure user accesses to keep MM fully aware of page state.
The issue is peudo-random because it only shows up if the TLB entry
installed in #1 is present at the time of #3. If it is evicted out, due
to TLB pressure or some-such, then copy_to_user() does take a TLB Miss
Exception, with a routine write-to-anon COW processing installing a
fresh page for kernel writes and also usable as it is in userspace.
Further the issue was dormant for so long as it depends on where the
libc internal read buffer (in .bss) is mapped at runtime.
If it happens to reside in file-backed data mapping of libc (in the
page-aligned slack space trailing the file backed data), loader zero
padding the slack space, does the early cow page replacement, setting
things up at the very beginning itself.
With gcc 4.8 based builds, the libc buffer got pushed out to a real
anon mapping which triggers the issue.
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Flush and INVALIDATE the dcache page.
This helper is only used for writeback of CODE pages to memory. So
there's no value in keeping the dcache lines around. Infact it is risky
as a writeback on natural eviction under pressure can cause un-needed
writeback with weird issues on aliasing dcache configurations.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
I'm satisified with testing, specially with fuse which has historically given
grief to VIPT arches (ARM/PARISC...)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=r4lw
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull second set of arc arch updates from Vineet Gupta:
"Aliasing VIPT dcache support for ARC
I'm satisified with testing, specially with fuse which has
historically given grief to VIPT arches (ARM/PARISC...)"
* tag 'arc-v3.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [TB10x] Remove GENERIC_GPIO
ARC: [mm] Aliasing VIPT dcache support 4/4
ARC: [mm] Aliasing VIPT dcache support 3/4
ARC: [mm] Aliasing VIPT dcache support 2/4
ARC: [mm] Aliasing VIPT dcache support 1/4
ARC: [mm] refactor the core (i|d)cache line ops loops
ARC: [mm] serious bug in vaddr based icache flush
* Support for two new platforms based on ARC700
- Abilis TB10x SoC [Chritisian/Pierrick]
- Simulator only System-C Model [Mischa]
* ARC specific MM improvements
- Avoid full TLB flush (ASID increment) on munmap (even single page)
- VIPT Cache Flushing improvements
+ Delayed dcache flush for non-aliasing dcache (big performance boost)
+ icache flush aliasing agnostic (no need to kill all possible aliases)
* Others
- Avoid needless rebuild of DTB files for every kernel build
- Remove builtin cmdline as that is already provided by DeviceTree/bootargs
- Fixing unaligned access emulation corner case
- checkpatch fixes [Sachin]
- Various fixlets [Noam]
- Minor build failures/cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDp
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC port updates from Vineet Gupta:
"Support for two new platforms based on ARC700:
- Abilis TB10x SoC [Chritisian/Pierrick]
- Simulator only System-C Model [Mischa]
ARC specific MM improvements:
- Avoid full TLB flush (ASID increment) on munmap (even single page)
- VIPT Cache Flushing improvements
+ Delayed dcache flush for non-aliasing dcache (big performance boost)
+ icache flush aliasing agnostic (no need to kill all possible aliases)
Others:
- Avoid needless rebuild of DTB files for every kernel build
- Remove builtin cmdline as that is already provided by DeviceTree/bootargs
- Fixing unaligned access emulation corner case
- checkpatch fixes [Sachin]
- Various fixlets [Noam]
- Minor build failures/cleanups"
* tag 'arc-v3.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (35 commits)
ARC: [mm] Lazy D-cache flush (non aliasing VIPT)
ARC: [mm] micro-optimize page size icache invalidate
ARC: [mm] remove the pessimistic all-alias-invalidate icache helpers
ARC: [mm] consolidate icache/dcache sync code
ARC: [mm] optimise icache flush for kernel mappings
ARC: [mm] optimise icache flush for user mappings
ARC: [mm] optimize needless full mm TLB flush on munmap
ARC: Add support for nSIM OSCI System C model
ARC: [TB10x] Adapt device tree to new compatible string
ARC: [TB10x] Add support for TB10x platform
ARC: [TB10x] Device tree of TB100 and TB101 Development Kits
ARC: Prepare interrupt code for external controllers
ARC: Allow embedded arc-intc to be properly placed in DT intc hierarchy
ARC: [cmdline] Don't overwrite u-boot provided bootargs
ARC: [cmdline] Remove CONFIG_CMDLINE
ARC: [plat-arcfpga] defconfig update
ARC: unaligned access emulation broken if callee-reg dest of LD/ST
ARC: unaligned access emulation error handling consolidation
ARC: Debug/crash-printing Improvements
ARC: fix typo with clock speed
...
This is the meat of the series which prevents any dcache alias creation
by always keeping the U and K mapping of a page congruent.
If a mapping already exists, and other tries to access the page, prev
one is flushed to physical page (wback+inv)
Essentially flush_dcache_page()/copy_user_highpage() create K-mapping
of a page, but try to defer flushing, unless U-mapping exist.
When page is actually mapped to userspace, update_mmu_cache() flushes
the K-mapping (in certain cases this can be optimised out)
Additonally flush_cache_mm(), flush_cache_range(), flush_cache_page()
handle the puring of stale userspace mappings on exit/munmap...
flush_anon_page() handles the existing U-mapping for anon page before
kernel reads it via the GUP path.
Note that while not complete, this is enough to boot a simple
dynamically linked Busybox based rootfs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This preps the low level dcache flush helpers to take vaddr argument in
addition to the existing paddr to properly flush the VIPT dcache
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Nothing semantical
* simplify the alignement code by using & operation only
* rename variables clearly as paddr
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
vaddr used to index the cache was clipped from the wrong end, and thus
would potentially fail to flush the correct lines.
The problem was dorment for so long because up until the recent
optimizations it was only used for ptrace break-point only flushes.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
flush_dcache_page( ) is MM hook to ensure that a page has consistent
views between kernel and userspace. Thus it is called when
* kernel writes to a page which at some later point could get mapped to
userspace (so kernel mapping needs to be flushed-n-inv)
* kernel is about to read from a page with possible userspace mappings
(so userspace mappings needs to be made coherent with kernel ones)
However for Non aliasing VIPT dcache, any userspace mapping will always
be congruent to kernel mapping. Thus d-cache need need not be flushed at
all (or delayed indefinitely).
The only reason it does need to be flushed is when mapping code pages.
Since icache doesn't snoop dcache, those dirty dcache lines need to be
written back to memory and icache line invalidated so that icache lines
fetch will get the right data.
Decent gains on LMBench fork/exec/sh and File I/O micro-benchmarks.
(1) FPGA @ 80 MHZ
Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
3.9-rc6-a Linux 3.9.0-r 80 4.79 8.72 66.7 116. 239. 8.39 30.4 4798 14.K 34.K
3.9-rc6-b Linux 3.9.0-r 80 4.79 8.62 65.4 111. 239. 8.35 29.0 3995 12.K 30.K
3.9-rc7-c Linux 3.9.0-r 80 4.79 9.00 66.1 106. 239. 8.61 30.4 2858 10.K 24.K
^^^^ ^^^^ ^^^
File & VM system latencies in microseconds - smaller is better
-------------------------------------------------------------------------------
Host OS 0K File 10K File Mmap Prot Page 100fd
Create Delete Create Delete Latency Fault Fault selct
--------- ------------- ------ ------ ------ ------ ------- ----- ------- -----
3.9-rc6-a Linux 3.9.0-r 317.8 204.2 1122.3 375.1 3522.0 4.288 20.7 126.8
3.9-rc6-b Linux 3.9.0-r 298.7 223.0 1141.6 367.8 3531.0 4.866 20.9 126.4
3.9-rc7-c Linux 3.9.0-r 278.4 179.2 862.1 339.3 3705.0 3.223 20.3 126.6
^^^^^ ^^^^^ ^^^^^ ^^^^
(2) Customer Silicon @ 500 MHz (166 MHz mem)
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
abilis-ba Linux 3.9.0-r 497 0.71 1.38 4.58 12.0 35.5 1.40 3.89 2070 5525 13.K
abilis-ca Linux 3.9.0-r 497 0.71 1.40 4.61 11.8 35.6 1.37 3.92 1411 4317 10.K
^^^^ ^^^^ ^^^
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
start address is already page aligned and size is const PAGE_SIZE,
thus fixups for alignment not needed in generated code.
bloat-o-meter vmlinux-mm5 vmlinux
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-32 (-32)
function old new delta
__inv_icache_page 82 50 -32
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that we have same helper used for all icache invalidates (i.e.
vaddr+paddr based exact line invalidate), consolidate the open coded
calls into one place.
Also rename flush_icache_range_vaddr => __sync_icache_dcache
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This change continues the theme from prev commit - this time icache
handling for kernel's own code modification (vmalloc: loadable modules,
breakpoints for kprobes/kgdb...)
flush_icache_range() calls the CDU icache helper with vaddr to enable
exact line invalidate.
For a true kernel-virtual mapping, the vaddr is actually virtual hence
valid as index into cache. For kprobes breakpoint however, the vaddr arg
is actually paddr - since that's how normal kernel is mapped in ARC
memory map. This implies that CDU will use the same addr for
indexing as for tag match - which is fine since kernel code would only
have that "implicit" mapping and none other.
This should speed up module loading significantly - specially on default
ARC700 icache configurations (32k) which alias.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC icache doesn't snoop dcache thus executable pages need to be made
coherent before mapping into userspace in flush_icache_page().
However ARC700 CDU (hardware cache flush module) requires both vaddr
(index in cache) as well as paddr (tag match) to correctly identify a
line in the VIPT cache. A typical ARC700 SoC has aliasing icache, thus
the paddr only based flush_icache_page() API couldn't be implemented
efficiently. It had to loop thru all possible alias indexes and perform
the invalidate operation (ofcourse the cache op would only succeed at
the index(es) where tag matches - typically only 1, but the cost of
visiting all the cache-bins needs to paid nevertheless).
Turns out however that the vaddr (along with paddr) is available in
update_mmu_cache() hence better suits ARC icache flush semantics.
With both vaddr+paddr, exactly one flush operation per line is done.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Use common help functions to free reserved pages.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no (Kconfig) macro CONFIG_BLOCK_DEV_RAM. (CONFIG_BLK_DEV_RAM
does exist though.) But linux/blk.h got killed in 2005 anyway (in a
patch titled "kill blk.h"), so these three lines can be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Fixes the following coding style issues as detected by checkpatch:
ERROR: space required before the open parenthesis '('
ERROR: "foo * bar" should be "foo *bar"
WARNING: space prohibited between function name and open parenthesis '('
WARNING: please, no spaces at the start of a line
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Silences the following checkpatch warnings:
WARNING: Use #include <linux/ptrace.h> instead of <asm/ptrace.h>
WARNING: Use #include <linux/kprobes.h> instead of <asm/kprobes.h>
WARNING: Use #include <linux/kgdb.h> instead of <asm/kgdb.h>
WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
WARNING: Use #include <linux/cache.h> instead of <asm/cache.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
version.h header file inclusion is not necessary as detected by
versioncheck script.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
!CONFIG_ARC_HAS_(I|D)CACHE makes Linux disable caches (assuming they
exist in hardware) - mostly for debugging issues with new peripherals.
However, independent of CONFIG_ARC_HAS_(I|D)CACHE, Linux also needs to
handle, non-existant caches, using the information in Cache BCRs (Build
Configuration Reg)
Reported-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Implement ioremap_prot() to allow mapping IO memory with variable
protection
via TLB.
Implementing this allows the /dev/mem driver to use its generic access()
VMA callback, which in turn allows ptrace to examine data in memory
mapped regions mapped via /dev/mem, such as Arc DCCM.
The end result is that it is possible to examine values of variables
placed into DCCM in user space programs via GDB.
CC: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
CC: Noam Camus <noamc@ezchip.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Includes mapping of CCMs in address space
* Annotations to move arbitrary code/data into CCM
* Moving some of the critical code/data into CCM
* Runtime detection/reporting
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC common code to enable a SMP system + ISS provided SMP extensions.
ARC700 natively lacks SMP support, hence some of the core features are
are only enabled if SoCs have the necessary h/w pixie-dust. This
includes:
-Inter Processor Interrupts (IPI)
-Cache coherency
-load-locked/store-conditional
...
The low level exception handling would be completely broken in SMP
because we don't have hardware assisted stack switching. Thus a fair bit
of this code is repurposing the MMU_SCRATCH reg for event handler
prologues to keep them re-entrant.
Many thanks to Rajeshwar Ranga for his initial "major" contributions to
SMP Port (back in 2008), and to Noam Camus and Gilad Ben-Yossef for help
with resurrecting that in 3.2 kernel (2012).
Note that this platform code is again singleton design pattern - so
multiple SMP platforms won't build at the moment - this deficiency is
addressed in subsequent patches within this series.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rajeshwar Ranga <rajeshwar.ranga@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
This is minimal infrastructure needed for devicetree work.
It uses an a sample "skeleton" devicetree - embedded in kernel image -
to print the board, manufacturer by parsing the top-level "compatible"
string.
As of now we don't need any additional "board" specific "machine_desc".
TODO: support interpreting the command line as boot-loader passed dtb
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
This includes recent changes to make handler "retry" and/or "killable"
The killable (early exit) logic is loosely based on how SH implements it
return if SIGKILL + either of VM_FAULT_OOM or VM_FAULT_RETRY
which is different from Hexagon implementation which would NOT early
exit for
SIGKILL + VM_FAULT_OOM + !VM_FAULT_RETRY
credits: Non executable stack support from Simon Spooner
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC700 MMU provides for tagging TLB entries with a 8-bit ASID to avoid
having to flush the TLB every task switch.
It also allows for a quick way to invalidate all the TLB entries for
task useful for:
* COW sementics during fork()
* task exit()ing
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* ARC700 has VIPT L1 Caches
* Caches don't snoop and are not coherent
* Given the PAGE_SIZE and Cache associativity, we don't support aliasing
D$ configurations (yet), but do allow aliasing I$ configs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Arnd in his review pointed out that arch Kconfig organisation has several
deficiencies:
* Build time entries for things which can be runtime extracted from DT
(e.g. SDRAM size, core clk frequency..)
* Not multi-platform-image-build friendly (choice .. endchoice constructs)
* cpu variants support (750/770) is exclusive.
The first 2 have been fixed in subsequent patches.
Due to the nature of the 750 and 770, it is not possible to build for
both together, w/o special runtime glue code which would hurt
performance.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Vineet Gupta
Linus Torvalds
Noam Camus
Jiang Liu
Paul Bolle
Sachin Kamat
Gilad Ben-Yossef