When there is a ptype handler holding a clone of this skb, whose
destination MAC addresse is overwritten, the owner of this handler may
get a corrupted packet.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions are only used when net poll controller is enabled.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer requires multicast capability flag set during IFACE_CREATE
for adding multicast filters.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Lancer disable interrupts in close by disarming CQs and EQs.
Change the order of calls in be_close to achieve the correct result.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove TX Queue stop in close
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add error recovery during load for Lancer
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L4 checksum field is valid only for TCP/UDP packets in Lancer
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Workaround added for Lancer in handling RX ERR completion received
when no RX buffers are posted is not needed.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows "ethtool advertise" to control the speed and duplex
features the device offers the switch.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
MAINTAINERS: Add Andy Gospodarek as co-maintainer.
r8169: disable ASPM
RxRPC: Fix v1 keys
AF_RXRPC: Handle receiving ACKALL packets
cnic: Fix lost interrupt on bnx2x
cnic: Prevent status block race conditions with hardware
net: dcbnl: check correct ops in dcbnl_ieee_set()
e1000e: disable broken PHY wakeup for ICH10 LOMs, use MAC wakeup instead
igb: fix sparse warning
e1000: fix sparse warning
netfilter: nf_log: avoid oops in (un)bind with invalid nfproto values
dccp: fix oops on Reset after close
ipvs: fix dst_lock locking on dest update
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
bnx2x: update driver version to 1.62.00-6
bnx2x: properly calculate lro_mss
bnx2x: perform statistics "action" before state transition.
bnx2x: properly configure coefficients for MinBW algorithm (NPAR mode).
bnx2x: Fix ethtool -t link test for MF (non-pmf) devices.
bnx2x: Fix nvram test for single port devices.
...
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: kill loop_mutex
blktrace: Remove blk_fill_rwbs_rq.
block: blk-flush shouldn't call directly into q->request_fn() __blk_run_queue()
block: add @force_kblockd to __blk_run_queue()
block: fix kernel-doc format for blkdev_issue_zeroout
blk-throttle: Do not use kblockd workqueue for throtl work
Netlink message processing in the kernel is synchronous these days,
capabilities can be checked directly in security_netlink_recv() from
the current process.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Reviewed-by: James Morris <jmorris@namei.org>
[chrisw: update to include pohmelfs and uvesafb]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pr_fmt.
Removed trailing "\n" from version,
add back via pr_info("%s\n", version);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bit more data to the output.
Convert string speeds to integer.
Object size reduced a tiny bit.
$ size drivers/net/mii.o*
text data bss dec hex filename
4155 56 1000 5211 145b drivers/net/mii.o.new
4184 56 1000 5240 1478 drivers/net/mii.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current logging styles.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neatening and standardization to the current logging mechanisms.
Miscellaneous speen/speed typo correction.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it isn't necessary nor really useful any longer.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend be_alloc_pages() with a gfp parameter, so that we use GFP_KERNEL
allocations instead of GFP_ATOMIC when not running in softirq context.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current logging forms with pr_fmt.
Convert DBG macro to tun_debug, use netdev_printk as well.
Add printf verification when TUN_DEBUG not defined.
Miscellaneous comment typo fix.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FTMAC100 Ethernet Media Access Controller supports 10/100 Mbps and
MII. This driver has been working on some ARM/NDS32 SoC's including
Faraday A320 and Andes AG101.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some time is known that ASPM is causing troubles on r8169, i.e. make
device randomly stop working without any errors in dmesg.
Currently Tomi Leppikangas reports that system with r8169 device hangs
with MCE errors when ASPM is enabled:
https://bugzilla.redhat.com/show_bug.cgi?id=642861#c4
Lets disable ASPM for r8169 devices at all, to avoid problems with
r8169 PCIe devices at least for some users.
Reported-by: Tomi Leppikangas <tomi.leppikangas@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating the copyrights for 2011 as well as make the ixgbe_copyright string
a constant.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 devices grabs semaphores differently than 82599 and 82598
devices do. They do however also grab them in allot of the same
functions. So I'm adding a new MAC operation function pointer to
allow us to use the correct function based on our MAC type. I'm also
changing all the semaphore calls to use this new function pointer.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up commented out include file and use #define instead of hard coded
value for number of RAR entries.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I2C interface was not being correctly locked down per port. As such
this can lead to race conditions that can cause issues. This patch cleans
up the handling to make certain we are not experiencing racy I2C access.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were reading the address after it had been initialized and this results
in the permanent address on the system being changed. This change corrects
that by storing the address before we re-initialize it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains a number of whitespace and formatting cleanups.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch specifically checks for 100 Full link speed instead of
assuming we are linked at 100 if not linked at 10G and 1G.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes the unused code that was setting up the uc_addr_list.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change modifies the ixgbe drivers so that it will not drop the
multicast filters while updating them. Instead it uses an intermediate
table to store the filter and then writes that filter to the hardware.
Based on original patch from Dave Boutcher <daveboutcher@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Dave Boutcher <daveboutcher@gmail.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 PHY reset pointer isn't currently used which is a good thing as it
wouldn't work as implemented. On top of that the X540 firmware is written
with the assumption that is does not need to be reset for proper
initialization so it's not needed. I'm just assigning the pointer at NULL
as the current implementation is rather misleading.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that out of bounds requests to these calls will
now return IXGBE_ERR_INVALID_ARGUMENT instead of returning 0.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fills in the values for bus speed and width of the
ixgbe_bus_speed and ixgbe_bus_width enums.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some PHYs require that we poll the reset bit and wait for it to clear
before continuing initialization. As such we should add this check to the
end of the ixgbe_reset_phy_generic routine.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently check link reports the link state as down, if at any time
the link had previously gone down since the last time the LINKS
register was read. This does not accurately reflect the function of
the check link call, which should be to return the CURRENT link
state. Code now reads the LINKS registers twice, once to clear the
previous and again to get the current value.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up several issues in ixgbe_identify_sfp_module_generic
including whitespace, redundant code, I2C EEPROM reads without exception
handling, and an if/elseif/else without braces.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double resets are required for recovery from certain error conditions.
Between resets, it is necessary to stall to allow time for any pending HW
events to complete. We use 1usec since that is what is needed for
ixgbe_disable_pcie_master(). The second reset then clears out any effects
of those events.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The media type was not being set for the 82599 T3 LAN on motherboard. This
change corrects that.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incorrectly freeing IRQs that we had not requested. This change
corrects that by making certain we only free q_vectors that we have
requested IRQs for.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up much of the logic related to the hardware semaphores
on the adapters. There were a number of issues with timings that needed to
be addressed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change just cleans up a few defines in ixgbe_type.h related to wake on LAN.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changli Gao
David S. Miller
Padmanabh Ratnakar
Francois Romieu
Oliver Neukum
Hayes Wang
John W. Linville
Linus Torvalds
Patrick McHardy
Joe Perches
Eric Dumazet
Po-Yu Chuang
Stanislaw Gruszka
Petr Uzel
Don Skidmore
Greg Rose
Emil Tantilov
Alexander Duyck