The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Preparation for IPv4 router
Ido says:
This series prepares the driver for IPv4 router support. The router follow-up
patches are available at: https://github.com/jpirko/linux_mlxsw/tree/net-next_queue
Patches 1-9 simplify the netdevice notification block and also add several
checks during PRECHANGEUPPER events against topologies that aren't supported by
the device. This will ensure L3 interfaces are only configured on top of
valid netdevs.
Patches 10-13 contain trivial changes required for the introduction of a generic
FID struct - currently only used for vFIDs - in patch 14. Making the FID
struct generic will allow us to easily associate the underlying FIDs with
their L3-counterparts - Router interfaces (RIFs):
FID Type | Used by | RIF Type
--------------------------------------------------------
FID | The VLAN-aware bridge | VLAN
vFID | VLAN-unaware bridges | FID
rFID | non-bridged netdevs (follow-up) | Sub-port
Obligatory ASCII art to visualize the above:
A.B.C.D
+
| FID RIF
+
br0 E.F.G.H
+ +
| | VLAN RIF
+---------+---------+ +
| | br1.W
| vFID | +
| | |
vPort +-+-+ +-+-+ +
swXpY.Z | | | | br1
+-+-+ +-+-+ +
| | FID=W |
| | +------------+------------+
| | | |
+---+---+ +---+-+-+ +---+---+
| | | | | |
| | | | | |
| | | | | |
+-------+ +-------+ +-------+
swXpY
Patches 15-16 further generalize the struct by exploiting the fact that the
FID is a shared resource among ports. Each FID type is assigned a 'leave'
function that is invoked based on CHANGEUPPER events and takes care of the
necessary clean-up.
Patches 17-22 build upon the previous patches and use the FID struct for the
VLAN-aware bridge and take care of cleaning up FID resources in the 'leave'
functions. For now, these are only FDB records, but later on we'll have to
remove the RIFs associated with these FIDs, which will in turn take care of
routes and neighbours clean-up.
The last patch adds debug prints that proved very useful during the
development of this series.
Tested with the existing L2 recipes:
https://github.com/jpirko/lnst/tree/master/recipes/switchdev
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug purposes, it's useful to know the order in which the driver
responds to changes in the topology of its upper devices.
Add debug prints to signal these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.
Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).
However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.
The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.
Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.
When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).
This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When L3 interfaces will be introduced a vPort won't necessarily have a
FID assigned to it. This can happen if it's not member in a bridge (in
which case it's assigned a vFID) or doesn't have an IP address (in which
case it's assigned an rFID).
Therefore, instead check the VID parameter to test whether a port is a
vPort or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.
Upon first use of the FID by any of the ports do the following:
1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID
Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.
When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.
The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vPort is created or when it joins a bridge we always do the same
set of operations:
1) Create the vFID, if not already created
2) Setup flooding for the vFID
3) Map the {Port, VID} to the vFID
When a vPort is destroyed or when it leaves a bridge the reverse is
performed.
Encapsulate the above in join / leave functions and simplify the code.
FIDs and rFIDs will use a similar set of functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:
1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.
The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.
Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.
Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a FID index instead of vFID and ease the transition towards a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FID used by a vPort (vFID, but also rFID later in the series) is
always mapped using {Port, VID} and not only VID as with the 4K FIDs of
the VLAN-aware bridge.
Instead of specifying all the arguments each time, just wrap this
operation using a dedicated function and simplify the code.
As before, the function takes FID as its argument in preparation for a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and use only one function for vFID creation /
destruction.
Unlike before, the function receives a FID index as its argument and not
a vFID index. Instead of passing 0, now one would need to pass 4K, which
is the first vFID.
This is the first step in creating a generic FID struct that will be
used for all three types of FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all call sites 'only_uc' is set to false, so strip it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a macro to do this kind of declarations, so use it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hold a reference count on the number of ports member in the
VLAN-aware bridge, as we only support one.
Instead of always incrementing / decrementing the reference count after
joining / leaving the bridge, simply do this accounting in the join /
leave functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'br_dev' is never used, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When responding to unlinking CHANGEUPPER notifications we shouldn't
return any value, as it's not checked by upper layers.
In addition, there's nothing the driver can do in case of failure, so it
should simply continue and try to free as much resources as possible and
not stop on first error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking for a condition and then issue the warning, just do
it in one go and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When upper device of a VLAN device changes we already made sure it's
a bridge device in PRECHANGEUPPER, so no need to check it's a master
device in CHANGEUPPER.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port netdev is put under LAG it cannot have VLAN upper devices,
so forbid that. The LAG device itself can have VLAN upper devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only support the following upper devices for port netdevs:
1) Bridge
2) LAG (bond / team)
3) VLAN
Any other device is forbidden, so return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking the error value and returning NOTIFY_BAD, just use
notifier_from_errno() and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yisen Zhuang says:
====================
net: hns: fix some bugs in hns driver
This series includes some bugs fixed. All these patches needs to be
applied after the patchset about ACPI support, so this series is
floated to net-next list.
The patches are:
> from Daode, fixes about pfc pause frame, getting coaslesce, led
control logic, TSO on|off and tcam table configuration.
> from Jun He, fix the potential leak to port unavailable
> from Kejian, fix bug of loopback and failing to test ping6
> from Qianqian, fix the several typo in hns driver
For more details, please see individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable/disable tso, the driver tries to access the hardware register,
but this operation will cause the port unavalible when there is traffic.
This patch tries to enable TSO when initialize, then control tso through
TSE bit in transmit descriptor.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default coalesce timeout is 3us, which is will cause CPU
usage is too high. This patch change it to 50us in order to reduce
CPU usage and the value makes sure network latency also meets requirement.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default sbm config parameter leaves little buffer when there is heavy
traffic, which will cause packets drop. This patch changes them to make
enough buffers for handling packets.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns_nic_poll_rx_skb alloc skb fail, it will break receive cycle and
read new fbd_num to start new receive cycle. It recomputes cycle num is
fbd_num minus clean_count, actually this cycle num is too big because
it drop out receive cycle. It brings about the port unavailable.
So we will goto out when alloc skb fail to fix this bug.
Signed-off-by: Jun He <hjat2005@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default driver sets anchor led bit to 0 when link down,
actually, the anchor bit should be set to 1, so fixes it when
link status is down.
Secondly, change the return value of cpld_set_led_id to 0, which
means leave the cpld to control led blink frequece other than the
driver itself.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When network interface is enabled, the ring enable operation is
conducted twice. This patch deletes the redundancy code of ring enable,
and integrates hnae_ae_ops.toggle_queue_status other functions to
hns_ae_start.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds get_coalesce_range api for hns, it shows
range of coalesce usecs and frames that can be set on
this interface.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver stores the high bit value of tcam data register
to the tcam data low element, stores the low bit value of tcam data
register to tcam data high element, this patch fixes this bug.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds spin lock for tcam table operation,
there maybe a race condition happens when more than
one thread try to change the tcam talbe entries.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SoC hip06, PFC pause handled in dsaf, while hip05 in XGMAC,
so change the statistics of pfc pause in dsaf and remove the old
pfc pause frame statistics.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug-ports,there are two non-synchronized processes:
Speed-Auto-Negotiation and Link-Update-Status. The two
processes are towed by two different state machines.
Bond reads the speed when link up, but the speed maybe
not update the right value at that time.That make for bond's
wrong speed. Thus only one state machine should be used and
if phy_state_machine is used, it does not need to do
hns_nic_update_link_status().
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When run ethtool cmd(ethtool -t ethx) again and again for a long
time, it will be probabilistically fail. The PHYs' registers may
be on different pages, so it must be switch to the right page
before setting PHYs' registers.
And __lb_up() calls phy_start() to startup the PHYs device, but
this function may change Copper Control Register(Page 0, Register 0)
to an other value. It would cause phy loopback test fail. if we
remove phy_start(), we have to remove the relative phy_stop(),
phy_disconnect() when doing phy loopback to keep the phy stay in
right status.
Reported-by: hejun <hjat2005@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Hilink3 and Hilink4 use the same xge training and xge u adaptor for
HNSv2, it needs to select which Hilink to be set before relative serdes
being configed. The hilink_access_sel is the register to do that.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error info should be printed as "set mask to 64bit fail!" instead of
"set mask to 32bit fail!" in dma_set_mask_and_coherent().
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource, it will unmap the map
automatically, remove the unnecessary the resource free.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The annotation info for hns_nic_reset_subtask() should be
"for resetting subtask" instead of "for resetting suntask".
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS receives a packet without doing anything, but it should call
skb_reset_mac_header() to initialize the header before using
eth_hdr().
Fixes: 0d6b425a37
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For service port, hns dsaf v1 support to close tx_pause.
However, the port will be invalid when it run command
ethtool to close tx_pause. This patch will fix it.
Signed-off-by: Qianqian Xie <xieqiaqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit fileds of PPE reset register are different between HNS v1 and
HNS v2, but the current procedure just only match HNS v1. Here is a
patch to fix it.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: probe compatible
This patchset factorizes the legacy and new SMI probing and abstracts
the switch register accesses. This simplifies adding support for new
chips or alternative register accesses.
This will allow us to use a compatible chip info to describe how to
access the SMI device and its switch ID register at probe time.
For the legacy probe, we fix the compatible info to 88E6085. For the
MDIO probe, we will use the compatible info from the device node data.
All patches are reviewed.
Changes since v4:
- fix debug printing (was 'val' instead of '*val')
Changes since v3 [3]:
- better register access abstraction using the chip structure
Changes since v2 [2]:
- do not guess compatible model in legacy probe
- add low level SMI API using a chip structure
- allocate before probe and detection
- add 3 cosmetic patches
Changes since v1 [1]:
- merge style fix from Ben Dooks
- add Acked-by/Reviewed-by tags
- drop one compatible string per model
- detect the SMI device based on the compatible info
- add an SMI ops structure
[1] https://lkml.org/lkml/2016/6/8/1201
[2] https://lkml.org/lkml/2016/6/14/671
[3] https://lkml.org/lkml/2016/6/17/995
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the SMI address of the switch chip is zero, the chip assumes to be
the only one on the SMI master bus and thus responds to all its known
SMI devices addresses (port registers, Global2, etc.)
When its SMI address is not zero, some chips (e.g. 88E6352) use an
indirect access through two SMI Command and Data registers.
Other models (e.g. 88E6060) using less than 16 internal SMI addresses
always use a direct access.
Add a capability flag to describe chips supporting the (indirect)
Multi-chip Addressing Mode, and a low-level API to access the registers
via SMI.
Other accesses (like Ethernet management frames) may be added later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch ID is located at address 0x3 of every Port Registers bank.
But not all Marvell switches have their Port Registers SMI Addresses
starting at 0x10. 88E6060 starts at 0x8 and 88E6390 starts at 0x0.
Add this data in the info structure and use it in the detection code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After allocating the chip structure, pass it a compatible info pointer.
The compatible info structure will be used later to describe how to
access the switch registers and where to read the switch ID.
For the standard MDIO probe, get it from the device node data. For the
legacy DSA driver probing, pass it the 88E6085 info.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the common detection code which assigns the info structure to
the chip given the read switch ID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes
David S. Miller
Ido Schimmel
Daode Huang
Jun He
Qianqian Xie
Kejian Yan
Qianqian Xie
Vivien Didelot