The ATU Learn2All feature allows newly learnt addresses to be spanned on
ports marked as "Message Port", currently all DSA ports.
This commit enables this feature which is necessary and quite convenient
for multi-chip switch fabrics.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".
This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the configuration of the default ageing time in a new
mv88e6xxx_atu_setup function.
That function will be extended later to contain all ATU related
configuration bits.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the ATU ageing time setter code in a new global1_atu.c file, which
will be extended in future patches to contains all consequent Global (1)
ATU support code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6097 chip requires watchdog_ops to be set.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ops needed to support the watchdog for the MV88E6390
family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch contains a watchdog looking for issues with the internal
gubbins of the switch. Hook the interrupt the watchdog triggers and
log the value of the control register indicating why the watchdog
fired. The watchdog can only be cleared with a switch reset, which
will destroy the current configuration. Rather than doing this, just
disable the interrupt.
The mv88e6390 family has different watchdog registers. So use an ops
structure, so support for the mv88e6390 family can be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the remaining port configuration code which varies per device
into port.c, using ops were necessary. This makes
mv88e6xxx_6185_family() and mv88e6xxx_6095_family() unused, so remove
them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike most ports, ports 9 and 10 of the 6390X family have configurable
PHY modes. Set the mode as part of adjust_link().
Ordering is important, because the SERDES interfaces connected to
ports 9 and 10 can be split and assigned to other ports. The CMODE has
to be correctly set before the SERDES interface on another port can be
configured. Such configuration is likely to be performed in
port_enable() and port_disabled(), called on slave_open() and
slave_close().
The simple case is port 9 and 10 are used for 'CPU' or 'DSA'. In this
case, the CMODE is set via a phy-mode in dsa_cpu_dsa_setup(), which is
called early in the switch setup.
When ports 9 or 10 are used as user ports, and have a fixed-phy, when
the fixed fixed-phy is attached, dsa_slave_adjust_link() is called,
which results in the adjust_link function being called, setting the
cmode. The port_enable() will for other ports will be called much
later.
When ports 9 or 10 are used as user ports and have a real phy attached
which does not use all the available SERDES interface, e.g. a 1Gbps
SGMII, there is currently no mechanism in place to set the CMODE of
the port from software. It must be hoped the stripping resistors are
correct.
At the same time, add a function to get the cmode. This will be needed
when configuring the SERDES interfaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 family uses a different ATU age timer coefficient.
Fix the info structures.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHYs of the mv88e6390 do not have a model ID. Trap any
calls to the ID register, and if it is zero, return the ID for the
mv88e6390. The Marvell PHY driver can then bind to this ID.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces.
It belongs to the Topaz family and unlike the 88E6341 it does not have
a TCAM.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces. It is partially compatible with switches of family
88E6352 and switches of family 88E6390.
This commit adds an initial support for this switch by describing its
capabilities to the driver and introducing a new family.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell ethernet switches have internal ethernet transceivers with
hardcoded phy addresses. These addresses can be greater than the number
of ports or its value might be different than the associated port number.
This is for example the case for MV88E6341 that has 6 ports and internal
Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.
This commits fixes the issue by removing the condition in MDIO callbacks.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.
Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.
Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.
This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has multiple MDIO busses. Generalize the parsing of the
device tree to support multiple mdio nodes. The external mdio bus has
a compatible strings to indicate it is external.
Keep a linked list of busses, placing the external mdio bus at the
tail of the list. When within the driver an mdio bus is needed,
e.g. for EEE or SERDES, use the head of the list which should be the
internal bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have the MDIO bus driver code allocate a private structure and make
the chip a member of it. This will allow us to add further members in
the future.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple MDIO busses, pass the mii_bus
structure to all PHY operations. It will in future then be clear on
which MDIO bus the operation should be performed.
For reads/write from phylib, the mii_bus is readily available. However
some internal code also access the PHY, e.g. for EEE and SERDES. Make
this code use the one and only currently available MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family has the internal PHYs mapped directly onto the
SMI register space as the switch. So the registers can be read
directly. Put a wrapper around this, in preparation for changing the
signature in order to support the external MDIO bus of the 6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 6352 chip has a 8-bit address/16-bit data EEPROM access.
The Marvell 6390 chip has a 16-bit address/8-bit data EEPROM access.
This patch implements the 8-bit data EEPROM access in the mv88e6xxx
driver and adds its support to chips of the 6390 family.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have properly encapsulated and made drivers utilize exported
functions, we can switch dsa_switch_ops to be a annotated with const.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for making struct dsa_switch_ops const, encapsulate it
within a dsa_switch_driver which has a list pointer and a pointer to
dsa_switch_ops. This allows us to take the list_head pointer out of
dsa_switch_ops, which is written to by {un,}register_switch_driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lookup in the ATU can be performed starting from a given MAC
address. This is faster than starting with the first possible MAC
address and iterating all entries.
Entries are returned in numeric order. So if the MAC address returned
is bigger than what we are searching for, we know it is not in the
ATU.
Using the benchmark provided by Volodymyr Bendiuga
<volodymyr.bendiuga@gmail.com>,
https://www.spinics.net/lists/netdev/msg411550.html
on an Marvell Armada 370 RD, the test to add a number of static fdb
entries went from 1.616531 seconds to 0.312052 seconds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices, such as the mv88e6097 do have ADDR[0] external and so it
is possible to configure the device to use SMI address 0x1. Remove the
restriction, as there are boards using this address.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@westermo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A port is not necessarily assigned to a netdev. And a port does not
need to be a member of a bridge. So when iterating over all ports,
check before using the netdev and bridge_dev for a port. Otherwise we
dereference a NULL pointer.
Fixes: da9c359e19 ("net: dsa: mv88e6xxx: check hardware VLAN in use")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell chips can enable/disable the PPU on demand. This is needed
to access the PHY registers when there is no indirection mechanism.
Add two new ppu_enable and ppu_disable ops to describe this and finally
get rid of the MV88E6XXX_FLAG_PPU* flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips have different way to issue a software reset.
Old chips (such as 88E6060) have a reset bit in an ATU control register.
Newer chips moved this bit in a Global control register. Chips with
controllable PPU should reset the PPU when resetting the switch.
Add a new reset operation to implement these differences and introduce a
mv88e6xxx_software_reset() helper to wrap it conveniently.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper to toggle the eventual GPIO connected to the reset pin.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before resetting a switch, the ports should be set to the Disabled state
and the transmit queues should be drained.
Add an helper to explicit that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DSA_TAG_PROTO_EDSA as tag_protocol for the mv88e6097. The
initialisation was missing before.
Fixes: a1f482aa8c33 ("net: dsa: mv88e6xxx: Move the tagging protocol into info")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a number flow control registers accessed via the
Flow Control register. Use these to set the pause control.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a different mechanism for configuring pause.
Refactor the code into an ops function, and for the moment, don't add
any mv88e6390 code yet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two different rate limiting configurations, depending on the
switch generation. Refactor this into ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches support jumbo frames. Refactor this code into operations
in the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older devices have a couple of registers in global2. The mv88e6390
family has a single register in global1 behind which hides similar
configuration. Implement and op for this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips only support DSA tagging. Newer chips have both DSA and
EDSA tagging. Refactor the code by adding port functions for setting the
frame mode, egress mode, and if to forward unknown frames.
This results in the helper mv88e6xxx_6065_family() becoming unused, so
remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port.
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips support a single tagging protocol, DSA. New chips support
both DSA and EDSA, an enhanced version. Having both as an option
changes the register layouts. Up until now, it has been assumed that
if EDSA is supported, it will be used. Hence the register layout has
been determined by which protocol should be used. However, mv88e6390
has a different implementation of EDSA, which requires we need to use
the DSA tagging. Hence separate the selection of the protocol from the
register layout.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 changes the monitor control register into the Monitor
and Management control, which is an indirection register to various
registers.
Add ops to set the CPU port and the ingress/egress port for both
register layouts, to global1
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 does not have the two registers to set the frame
priority map. Instead it has an indirection registers for setting a
number of different priority maps. Refactor the old code into an
function, implement the mv88e6390 version, and use an op to call the
right one.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings,
so free the same amount. This will be 8 or 9 in practice, less than 16.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing comment for the MV88E6097 because of unification.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing definition of g1_irqs for MV88E6097.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename functions to avoid _ prefix.
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename to mv88e6390_g1_stats_set_histogram
Move into global1.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
_mv88e6xxx_stats_wait() did not check the return value from
mv88e6xxx_g1_read(), so the compiler complained about set but unused
err.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing interrupts requires switch register access to mask the
interrupts. Hence we must hold the register mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error, remask the interrupts, release all maps, and remove the
domain. This cannot be done using the mv88e6xxx_g1_irq_free() because
some of these actions are not idempotent.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the g1 interrupt free code such that is masks any further
interrupts, and then releases the interrupt.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to remove an IRQ domain that was not created results in an
Opps. Add the necessary checks that the irqs were created before
freeing them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent refactoring of setting the MAC configuration broke setting
of RGMII delays, via the phy-mode, on the 6351 family. Add the missing
ops to the structure.
Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have setters to configure the port's MAC, use them to
refactor the port setup and adjust_link code.
Note that port's MAC speed, duplex or RGMII delay must not be changed
unless the port's link is forced down. So wrap all that in a
mv88e6xxx_port_setup_mac function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the two bits for link, duplex or RGMII delays are used the same
way on chips supporting the said feature, the two bits for speed have
different meaning for most of the chips out there.
Speed value is stored in bits 1:0, 0x3 means unforce (normal detection).
Some chips reuse values for alternative speeds when bit 12 is set.
Newer chips with speed > 1Gbps reuse value 0x3 thus need a new bit 13.
Here are the values to write in register 0x1 to (un)force speed:
| Speed | 88E6065 | 88E6185 | 88E6352 | 88E6390 | 88E6390X |
| ------- | ------- | ------- | ------- | ------- | -------- |
| 10 | 0x0000 | 0x0000 | 0x0000 | 0x2000 | 0x2000 |
| 100 | 0x0001 | 0x0001 | 0x0001 | 0x2001 | 0x2001 |
| 200 | 0x0002 | NA | 0x1001 | 0x3001 | 0x3001 |
| 1000 | NA | 0x0002 | 0x0002 | 0x2002 | 0x2002 |
| 2500 | NA | NA | NA | 0x3003 | 0x3003 |
| 10000 | NA | NA | NA | NA | 0x2003 |
| unforce | 0x0003 | 0x0003 | 0x0003 | 0x0000 | 0x0000 |
This patch implements a generic mv88e6xxx_port_set_speed() function used
by chip-specific wrappers to filter supported ports and speeds.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips such as 88E6352 and 88E6390 can be programmed to add delays
to RXCLK for IND inputs or to GTXCLK for OUTD outputs when port is in
RGMII mode.
Add a port function to program such delays according to the provided PHY
interface mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to port's link, add setter to force port's half duplex, full
duplex or let normal duplex detection occurs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the chips will have a port register control bits to force the
port's link up, down, or let normal link detection occurs.
Implement such operation to use it later when setting duplex, etc.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to set the port 802.1Q mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to access the ports default VID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to port files to access the ports default FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a port function to access the Port Based VLAN Map register.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the port STP state setter to the port files.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switches contains one internal SMI device per port, called
"Port Registers". Depending on the model, the addresses of these devices
start from 0x0, 0x8 or 0x10.
Start moving Port Registers specific code to their own files.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the function
and data fields.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/dsa/mv88e6xxx/chip.c:2866:5: warning:
symbol 'mv88e6xxx_g1_set_switch_mac' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch can have up to two interrupt controllers. One of these
contains the interrupts from the integrated PHYs, so is useful to
export. The Marvell PHY driver can then be used in interrupt mode,
rather than polling, speeding up PHY handling and reducing load on the
MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove EEPROM flags in favor of new {get,set}_eeprom chip-wide
functions in the mv88e6xxx_ops structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a set_switch_mac chip-wide function to mv88e6xxx_ops and remove
MV88E6XXX_FLAG_G2_SWITCH_MAC flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a mv88e6xxx_ops structure to describe supported chip-wide
functions and assign the correct variant to the chip models.
For the moment, add only PHY access routines. This allows to get rid of
the PHY ops structures and the usage of PHY flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_ops is used to describe how to access the chip registers.
It can be through SMI (via an MDIO bus), or via another interface such
as crafted remote management frames.
The correct BUS operations structure is chosen at runtime, depending on
the chip address and connectivity.
We will need the mv88e6xxx_ops name for future chip-wide operation
structure, thus rename mv88e6xxx_ops to more explicit mv88e6xxx_bus_ops.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The STU (if the switch has one) is abstracted and accessed through the
VTU operations and data registers.
Thus rename the mv88e6xxx_vtu_stu_entry struct to mv88e6xxx_vtu_entry.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an mv88e6xxx_num_ports helper instead of digging in the chip info
structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_num_databases will be used by shared code, so move it
inline to the header file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of Global 1 ATU FID register (0x01)
and VTU FID register (0x02), instead of checking families.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Global (1) internal SMI device is an extended set of registers
containing ATU, PPU, VTU, STU, etc.
It is present on every switches, usually at SMI address 0x1B. But old
models such as 88E6060 access it at address 0xF, thus using REG_GLOBAL
is erroneous.
Add a global1_addr info member used by mv88e6xxx_g1_{read,write} and
mv88e6xxx_g1_wait helpers in a new global1.c file.
This patch finally removes _mv88e6xxx_reg_{read,write}, in favor on the
appropriate helpers. No functional changes here.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/dsa/mv88e6xxx/chip.c:219:5: warning:
symbol 'mv88e6xxx_port_read' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx/chip.c:227:5: warning:
symbol 'mv88e6xxx_port_write' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA layer handles port fast ageing on correct STP change,
simplify _mv88e6xxx_port_state and implement mv88e6xxx_port_fast_age.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a device coming soon which places its port registers
somewhere different to all other Marvell switches supported so far.
Add helper functions for reading/writing port registers, making it
easier to handle this new device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An address can be loaded in the ATU with multiple ports, for instance
when adding multiple ports to a Multicast group with "bridge mdb".
The current code doesn't allow that. Add an helper to get a single entry
from the ATU, then set or clear the requested port, before loading the
entry back in the ATU.
Note that the required _mv88e6xxx_atu_getnext function is defined below
mv88e6xxx_port_db_load_purge, so forward-declare it for the moment. The
ATU code will be isolated in future patches.
Fixes: 83dabd1fa8 ("net: dsa: mv88e6xxx: make switchdev DB ops generic")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since not every chip has a Global2 set of registers, make its support
optional, in which case the related functions will return -EOPNOTSUPP.
This also allows to reduce the size of the mv88e6xxx driver for devices
such as home routers embedding Ethernet chips without Global2 support.
It is present on most recent chips, thus enable its support by default.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips are composed of multiple SMI devices. One of them at
address 0x1C is called Global2. It provides an extended set of
registers, used for interrupt control, EEPROM access, indirect PHY
access (to bypass the PHY Polling Unit) and cross-chip related setup.
Most chips have it, but some others don't (older ones such as 6060).
Now that its related code is isolated in mv88e6xxx_g2_* functions, move
it to its own global2.c file, making most of its setup code static.
Document each registers in the meantime.
Its compilation can be later avoided for chips without such registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access the priv member of the dsa_switch structure directly, instead of
having an unnecessary helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the MDB operations. This consists of
loading/purging/dumping multicast addresses for a given port in the ATU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDB support for the mv88e6xxx driver will be very similar to the FDB
support, since it consists of loading/purging/dumping address to/from
the Address Translation Unit (ATU).
Prepare the support for MDB by making the FDB code accessing the ATU
generic. The FDB operations now provide access to the unicast addresses
while the MDB operations will provide access to the multicast addresses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PORT_RATE_CONTROL register works differently on 88e6095/6095f/6131
in comparison to 6123/61/65, and 0x0 disables. The distinction was lost
Linux 4.1 --> 4.2
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without it, a mv88e6131 switch will not forward incoming unicast
packets to the CPU port.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPU method of accessing PHYs makes use of a timer. Make sure this
timer is deleted before unloading the driver.
Reported-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips only support DSA tagging on the CPU port. New devices
support both DSA and EDSA. The driver needs to tell the core the tag
protocol to use, and configure the switch for what is available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mv88e6xxx_wait() returns a timeout, something bad has
happened. Make sure it is noticed by logging an error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mv88e6xx_wait() iterated on a counter than a fixed time
interval, it implements the same mechanism as mv88e6xxx_update() uses.
So use it in mv88e6xx_wait().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx driver times out operations on the switch based on
looping until an elapsed wall clock time is reached. However, if
usleep_range() sleeps much longer than expected, it could timeout with
an error without actually checking to see if the devices has completed
the operation. So replace the elapsed time with a fixed upper bound on
the number of loops.
Testing on various switches has shown that switches takes either 0 or
1 iteration, so a maximum of 16 iterations is a safe limit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces every MDIO direct or indirect access with the new
generic mv88e6xxx_phy_* routines.
This allows us to get rid of the mv88e6xxx_mdio_{read,write}_{,in}direct
and {_,}mv88e6xxx_mdio_page_{read,write} functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mv88e6xxx_phy_page_{read,write} routines and use them to access the
SerDes PHY device registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old chips use a direct access to the PHY devices registers. Next chips
have a PHY Polling Unit (PPU) which needs to be disabled before
accessing PHY registers. Newer chips have an indirect access to the PHY
devices so that disabling the PPU is not necessary.
Introduce a new phy_ops structure in the chip to describe the required
PHY access routines.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe the presence of the Global2 SMI PHY registers, used to
indirectly access the internal SMI devices registers on some chips.
Also temporarily forward declare mv88e6xxx_g2_smi_phy_{read,write} to
use them in mv88e6xxx_mdio_{read,write}_indirect, before getting rid of
the later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of SMI Command and Data registers
used to indirectly access internal SMI devices registers when the switch
SMI address is not zero.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is no locked version of the wait routine anymore, rename
the _ prefixed version and make it use the new read API.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_DSA_HWMON is disabled, we get warnings about two unused
functions whose only callers are all inside of an #ifdef:
drivers/net/dsa/mv88e6xxx.c:3257:12: 'mv88e6xxx_mdio_page_write' defined but not used [-Werror=unused-function]
drivers/net/dsa/mv88e6xxx.c:3244:12: 'mv88e6xxx_mdio_page_read' defined but not used [-Werror=unused-function]
This adds another ifdef around the function definitions. The warnings
appeared after the functions were marked 'static', but the problem
was already there before that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 57d3231057 ("net: dsa: mv88e6xxx: fix style issues")
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the last usage of the locked mv88e6xxx_reg_read function with
a new mv88e6xxx_port_read helper, useful later for chips with different
port registers base address.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6352 family of switches and compatibles provide a 8-bit address and
16-bit data access to an optional EEPROM.
Newer chip such as the 6390 family slightly changed the access to 16-bit
address and 8-bit data.
This commit cleans up the EEPROM access code for 16-bit access and makes
it easy to eventually introduce future support for 8-bit access.
Here's a list of notable changes brought by this patch:
- provide Global2 unlocked helpers for EEPROM commands
- remove eeprom_mutex, only reg_lock is necessary for driver functions
- eeprom_len is 0 for chip without EEPROM, so return it directly
- the Running bit must be 0 before r/w, so wait for Busy *and* Running
- remove now unused mv88e6xxx_wait and mv88e6xxx_reg_write
- other than that, the logic (in _{get,set}_eeprom16) didn't change
Chips with an 8-bit EEPROM access will require to implement the
8-suffixed variant of G2 helpers and the related flag:
#define MV88E6XXX_FLAGS_EEPROM8 \
(MV88E6XXX_FLAG_G2_EEPROM_CMD | \
MV88E6XXX_FLAG_G2_EEPROM_ADDR)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the DSA driver function to configure the bridge ageing time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch chips from (88E6060 to 88E6390) have a ATU Control
register containing bits 11:4 to configure an ATU Age Time quotient.
However the coefficient used to calculate the ATU Age Time vary with the
models. E.g. 88E6060, 88E6352 and 88E6390 use respectively 16, 15 and
3.75 seconds.
Add a age_time_coeff to the info structure to handle this and a Global 1
helper to set the default age time of 5 minutes in the setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add capability flags to describe the presence of Ingress Rate Limit unit
registers and an helper function to clear it.
In the meantime, fix a few harmless issues:
- 6185 and 6095 don't have such registers (reserved)
- the previous code didn't wait for the IRL operation to complete
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags and helpers to describe the presence of Priority Override
Table (POT) related registers and simplify the setup of Global 2.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of Cross-chip Port VLAN Table (PVT)
related registers and simplify the setup of Global 2.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches such as 88E6185 as 3 Switch MAC registers in Global 1. Newer
chips such as 88E6352 have freed these registers in favor of an indirect
access in a Switch MAC/WoL/WoF register in Global 2.
Explicit this difference with G1 and G2 helpers and flags.
Also, note that this indirect access is a single-register which doesn't
require to wait for the operation to complete (like Switch MAC, Trunk
Mapping, etc.), in contrary to multi-registers indirect accesses with
several operations and a busy bit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches provide a Rsvd2CPU mechanism used to choose which of the
16 reserved multicast destination addresses matching 01:80:c2:00:00:0x
should be considered as MGMT and thus forwarded to the CPU port.
Other switches extend this mechanism to also configure as MGMT the
additional 16 reserved multicast addresses matching 01:80:c2:00:00:2x.
This mechanism is exposed via two registers in Global 2, and an Rsvd2CPU
enable bit in the management register.
Newer chip (such as 88E6390) has replaced these registers with a new
indirect MGMT mechanism in Global 1.
The patch adds two MV88E6XXX_FLAG_G2_MGMT_EN_{0,2}X flags to describe
the presence of these Global 2 registers. If 88E6390 support is added, a
MV88E6XXX_FLAG_G1_MGMT_CTRL flag will be needed to setup Rsvd2CPU.
Note: all switches still support in parallel the ATU Load operation with
an MGMT Entry State to forward such frames in a less convenient way.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Trunk Mask and Trunk Mapping registers are two Global 2 indirect
accesses to trunking configuration.
Add helpers for these tables and simplify the Global 2 setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Device Mapping register is an indirect table access.
Provide helpers to access this table and explicit the checking of the
new DSA_RTABLE_NONE routing table value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the setup of Global 1 and Global 2 internal SMI devices and add
a flag to describe the presence of this second registers set.
Also rearrange the G1 setup in the registers order.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 88E6xxx Marvell switches (even the old not supported yet 88E6060)
have at least an ATU, per-port STP states and VLAN map, to run basic
switch functions such as Spanning Tree and port based VLANs.
Get rid of the related MV88E6XXX_FLAG_{ATU,PORTSTATE,VLANTABLE} flags,
as they are defaults to every chip.
This enables STP on 6185 and removes many inconsistencies on others.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming support for cross-chip operations, it will be hard to
distinguish portions of code supporting a single-chip or a switch fabric
of interconnected chips.
Make the code clearer now, by renaming the mv88e6xxx_priv_state chip
structure to mv88e6xxx_chip. This patch brings no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot
Volodymyr Bendiuga
Andrew Lunn
Gregory CLEMENT
Romain Perier
Florian Fainelli
Volodymyr Bendiuga
Stefan Eichenberger
Andreas Färber
Wei Yongjun
David S. Miller
Jamie Lentin
Arnd Bergmann