When sending a FLOGI LS_ACC, which we only do in point-to-multipoint
mode, the MAC descriptor should have the granted MAC set to
0x0efd00 || D_ID.
When sending an LS_RJT, there should be no MAC descriptor.
When sending either an LS_ACC or LS_RJT, the subcode should indicate
an reply, not a request.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FC-BB-6 committee is proposing a new FIP usage model called
VN_port to VN_port mode. It allows VN_ports to discover each other
over a loss-free L2 Ethernet without any FCF or Fibre-channel fabric
services. This is point-to-multipoint. There is also a variant
of this called point-to-point which provides for making sure there
is just one pair of ports operating over the Ethernet fabric.
We add these new states: VNMP_START, _PROBE1, _PROBE2, _CLAIM, and _UP.
These usually go quickly in that sequence. After waiting a random
amount of time up to 100 ms in START, we select a pseudo-random
proposed locally-unique port ID and send out probes in states PROBE1
and PROBE2, 100 ms apart. If no probe responses are heard, we
proceed to CLAIM state 400 ms later and send a claim notification.
We wait another 400 ms to receive claim responses, which give us
a list of the other nodes on the network, including their FC-4
capabilities. After another 400 ms we go to VNMP_UP state and
should start interoperating with any of the nodes for whic we
receivec claim responses. More details are in the spec.j
Add the new mode as FIP_MODE_VN2VN. The driver must specify
explicitly that it wants to operate in this mode. There is
no automatic detection between point-to-multipoint and fabric
mode, and the local port initialization is affected, so it isn't
anticipated that there will ever be any such automatic switchover.
It may eventually be possible to have both fabric and VN2VN
modes on the same L2 network, which may be done by two separate
local VN_ports (lports).
When in VN2VN mode, FIP replaces libfc's fabric-oriented discovery
module with its own simple code that adds remote ports as they
are discovered from incoming claim notifications and responses.
These hooks are placed by fcoe_disc_init().
A linear list of discovered vn_ports is maintained under the
fcoe_ctlr struct. It is expected to be short for now, and
accessed infrequently. It is kept under RCU for lock-ordering
reasons. The lport and/or rport mutexes may be held when we
need to lookup a fcoe_vnport during an ELS send.
Change fcoe_ctlr_encaps() to lookup the destination vn_port in
the list of peers for the destination MAC address of the
FIP-encapsulated frame.
Add a new function fcoe_disc_init() to initialize just the
discovery portion of libfcoe for VN2VN mode.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enhancement: add debug messages at all state transitions.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FC-BB-6 committee is proposing a new FIP usage model called
VN_port to VN_port mode. It allows VN_ports to discover each other
over a loss-free L2 Ethernet without any FCF or Fibre-channel fabric
services. This is point-to-multipoint. There is also a variant
of this called point-to-point which provides for making sure there
is just one pair of ports operating over the Ethernet fabric.
This patch defines the new message type and subtypes as well as
one new descriptor type used by VN2VN mode.
These are all still at the proposed stage and subject to change.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When an exchange is received with a FIP encapsulation, we need
to know that the response must be sent via FIP and what the original
ELS opcode was. This becomes important for VN2VN mode, where we may
receive FLOGI or LOGO from several peer VN_ports, and the LS_ACC or
LS_RJT must be sent FIP-encapsulated with the correct sub-type.
Add a field to the struct fc_frame, fr_encaps, to indicate the
encapsulation values. That term is chosen to be neutral and
LLD-agnostic in case non-FCoE/FIP LLDs might find it useful.
The frame fr_encaps is transferred from the ingress frame to the
exchange by fc_exch_recv_req(), and back to the outgoing frame
by fc_seq_send().
This is taking the last byte in the skb->cb array. If needed,
we could combine the info in sof, eof, flags, and encaps
together into one field, but it'd be better to do that if
and when its needed.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FIP proposal for VN_port to VN_port point-to-multipoint
operation requires a FLOGI be sent to each remote port.
The FLOGI is sent with the assigned S_ID and D_IDs of the
local and remote ports. This and the response get
FIP-encapsulated for Ethernet.
Add FLOGI state to the remote port state machine.
This will be skipped if not in point-to-multipoint mode.
To reduce a little duplication between PLOGI and FLOGI
response handling, added fc_rport_login_complete(), which
handles the parameters for the rdata struct.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For VN_port to VN_port mode, the transport sets the port_id and
there's no lport FLOGI. This is similar to FC loop mode.
Add a point_to_multipoint flag that indicates the local port is in
point-to-multipoint mode. This skips FLOGI and discovery.
It also skips resetting the port_id on resets other than link down.
Add function fc_lport_set_local_id() that sets the local port_id.
This is called by libfcoe on behalf of the low-level driver
to set the port_id when the link comes up.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There are three modes that libfcoe currently supports, and a new one
is coming. Change the fcoe_ctlr_init() interface to add the mode
desired. This should not change any functionality.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For VN_port to VN_port mode, FIP will do discovery and needs a
way to find its state from the local port or discovery structure.
It seems that any other LLD that implements its own discovery
would also need something like this.
Replace disc->lport with disc->priv, and use container_of to
find the lport. We could use disc->priv for that, but
container_of is smaller and faster.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It turns out most of the FIP work is now done from worker threads
or process context now, so there's no need to use a spin lock.
Change to use mutex instead of spin lock and delayed_work instead
of a timer.
This will make it nicer for the VN_port to VN_port feature that
will interact more with the libfc layers requiring that
spinlocks not be held.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add pre-zeroed space after the allocation for fc_rport_priv
for use by the lower-level driver.
This is primarily for VN2VN FIP mode, but could be used in
other ways someday.
The space required is specified in lport->rport_priv_size.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To allow LLD to do lookups on rports without grabbing a mutex,
make them RCU-safe. The caller of lport->tt.rport_lookup will
have the choice of holding disc_mutex or the rcu_read_lock().
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is per FC-BB-5 Annex-D recommendation and per that
if address checking fails then drop the frame.
FIP code paths are already doing this so only needed for fcoe
frames.
The src address checking is limited to only fip mode since
this might break non-fip mode used in p2p due to used OUI
based addressing in some p2p code paths, going forward FIP
will be the only mode, therefore limited this to only FIP
mode so that it won't break non-fip p2p mode for now.
-v2
Removes FCOE packet type checking since fcoe_rcv is
registered to receive only FCoE type packets from netdev
and it is already checked by netdev.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fc_fabric_logoff and fc_fabric_login are redundant
here after recently added fcoe_ctlr_link_down/up to
these functions, therefore this patch removes logoff
and login to only use link down and up here. This works
best for their current usages with fcoe DCB link down or up.
This also works well to avoid EIO errors when fcoe DCB link
goes down as lport state moves out of ready quickly from
fcoe_ctlr_link_down and that allows re-queuing timed out IOs
for this case also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In this case, sync IO fails with EIO(5) errors as:-
"Thread:1 System call error:5 - Input/output error (::pwrite() failed)".
This is due to IO time out while libfc doing link down processing
to block all rports and if timed out IO was at last retry
attempt then it fails to user with EIO error followed by
these log messages.
[77848.612169] host2: rport bf0015: Delete port
[77848.612221] host2: rport e10aef: work delete
[77848.612232] host2: rport e10002: work event 3
[77848.612422] sd 2:0:1:1: [sdi] Unhandled error code
[77848.612426] sd 2:0:1:1: [sdi] Result: hostbyte=DID_ERROR
driverbyte=DRIVER_OK
[77848.612431] sd 2:0:1:1: [sdi] CDB: Write(10): 2a 00 00 00 11 20 00 00 20 00
[77848.612445] end_request: I/O error, dev sdi, sector 4384
[77848.612553] sd 2:0:1:2: [sdj] Unhandled error code
To fix these EIO errors, such timed out incomplete IOs needs
to be re-queued without counting retry attempt and this patch
does that using DID_REQUEUE scsi code.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Analyzing fcoe with sparse currently fails. This is because struct
fcoe_rcv_info contains two enum members that have been declared with
__attribute__((packed)). Apparently gcc honors this attribute while sparse
ignores it. The result is that sizeof(struct fcoe_rcv_info)
== sizeof(struct sk_buff::cb) == 48 on a 64-bit system according to gcc, but
not according to sparse. The patch below modifies the definition of
struct fcoe_rcv_info such that gcc and sparse interpret this structure
definition in the same way. The current sparse output is as follows:
$ cd linux-2.6.34
$ make C=2 M=drivers/scsi/fcoe modules
CHECK drivers/scsi/fcoe/fcoe.c
include/scsi/fc_frame.h:81:9: error: invalid bitfield width, -1.
CC [M] drivers/scsi/fcoe/fcoe.o
CHECK drivers/scsi/fcoe/libfcoe.c
include/scsi/fc_frame.h:81:9: error: invalid bitfield width, -1.
drivers/scsi/fcoe/libfcoe.c:56:37: error: invalid initializer
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Cc: jeykholt@cisco.com
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is exposed by a mpio test using EMC CLARiiON targets when LUN
tresspassing happens, the burst length from the XFER_READY for the
MODE SELECT(10) is 19 bytes, much smaller than FC_MIN_MAX_PAYLOAD as
256 bytes. This patch removes the related two WARN_ON()s.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch is to add next generation of Dell iSCSI PowerVault
controller MD36xxi into RDAC device list.
Signed-off-by: Yanqing Liu <Yanqing_Liu@Dell.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The check to test that "bus_no" was valid came after we had already used
it as an array offset. This patch moves it forward.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FCoE Related Fixes
- Correct find-next-FCF routine so that it searches at next FCF rather
than current one.
- Enhanced round-robin FCF failover algorithm to re-start on "New FCF"
async event
- Update the manner in which we look at FCFs while they may be in
their discovery state.
- Use LPFC_FCOE_NULL_VID macro when checkinf for valid vlan_id for FCF
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- BSG interface related:
- Fix node reference count if node is active
- Warn if we're overwriting an active CT context
- Discovery related:
- Clear "Ignore Reg Login" flag when purging mailbox queue
- Pay attention to return code for fc_block_scsi_eh()
- Stall device loss code if we're almost done when it fires
(we're logged in, but PRLI is outstanding)
- Bugs
- Correct DIF code for endianness issues
- Correct where we had missed points to check txq on i/o
completion/cleanup
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Setting the resource type in the ipr_update_res_entry function was incorrect in
that the top 4 bits were masked off. The assignment has been updated to no
longer mask those bits.
Then, two new attributes were added to allow the user space utilities to more
easily get information. The resource_type sdev attribute is set for all devices
in the adapter's configuration table and indicates the type of device. The
fw_type shost attribute indicates the firmware type supported by the adapter.
Finally, the resource_path attribute was changed to be mode S_IRUGO.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The method of transitioning to operational for new adapters includes using
initialization stages. The current stage is indicated via a register read.
The final good stage in the sequence is "operational" but does not necessarily
indicate that the driver can proceed. There is another bit that gets set in the
adapter->host interrupt register when the adapter has completed enough of its
bringup such that it can accept commands. The driver was not checking that
bit before proceeding which led to intermittent errors and adapter resets.
The fix is to check the "transition to operational" bit in the interrupt
register after detecting that the initialization stage is "operational" and
only proceed if both are set.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
be2iscsi driver should #include linux/if_ether.h since it uses
sysfs_format_mac().
It should also depend on NET since it selects SCSI_ISCSI_ATTRS,
which depends on NET.
These changes fix a build error when CONFIG_NET is not enabled:
ERROR: "sysfs_format_mac" [drivers/scsi/be2iscsi/be2iscsi.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes a bug where the buffer was being freed as soon as
submission to HW is done.
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes a Debug Print in the IO path
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch limits max_xmit_length to 64K incase older
utilities are used
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch ensures that the same ITT is maintained across
all login pdu's
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
These changes allow the driver to support crashdump. We need to reset the
chip incase of a crashdump
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch frees tags that are already allocated in case of
failure
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch handles request_irq failures by properly cleaning up
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
hwi_enable_intr need not return any value. This patch fixes the
that and removes code designed to handle a failure return value
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch frees up the allocated cid and returns error if allocation
of tag fails.
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch passes on the value returned by
beiscsi_open_conn
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixing some functions return values that did not match with
the possible return values
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes the return values as per comment from Mike Christie
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The latest checkpatch.pl throws some new warnings. Fixing it
to get rid of a bunch of warnings
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commit
commit 2c3c8bea60
Author: Chris Wright <chrisw@sous-sol.org>
Date: Wed May 12 18:28:57 2010 -0700
sysfs: add struct file* to bin_attr callbacks
Added an extra struct file * parameter at the beginning, which the
arcmsr binary attribute additions didn't have. Fix this to prevent
nasty crashes.
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes malloc(), free(), and printf() wrappers from the aic7xxx
SCSI driver. I didn't use pr_debug for printf because of some 'clever' uses of
printf don't compile with the pr_debug. I didn't fix the overeager uses of
GFP_ATOMIC either because I wanted to keep this patch as simple as possible.
[jejb:fixed up checkpatch errors and fixed up missed conversion]
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Handle one H/W Interrupt at a time to prevent holding off H/W lock
for longer period of time.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed the DMA allocated memory freeing which wasn't taken care
in many cases.
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Joe Eykholt
Vasu Dev
Bart Van Assche
Yi Zou
Yanqing_Liu@Dell.com
Dan Carpenter
James Smart
Wayne Boyer
Randy Dunlap
Jayamohan Kallickal
James Bottomley
Pekka Enberg
Cyril Jayaprakash
Vikas Chaudhary
Karen Higgins
Ravi Anand
Prasanna Mumbai