The Spreadtrum Audio compress offload mode will use 2-stage DMA transfer
to save power. That means we can request 2 dma channels, one for source
channel, and another one for destination channel. Once the source channel's
transaction is done, it will trigger the destination channel's transaction
automatically by hardware signal.
In this case, the source channel will transfer data from IRAM buffer to
the DSP fifo to decoding/encoding, once IRAM buffer is empty by transferring
done, the destination channel will start to transfer data from DDR buffer
to IRAM buffer. Since the destination channel will use link-list mode to
fill the IRAM data, and IRAM buffer is allocated by 32K, and DDR buffer
is larger to 2M, that means we need lots of link-list nodes to do a cyclic
transfer, instead wasting lots of link-list memory, we can use wrap address
support to reduce link-list node number, which means when the transfer
address reaches the wrap address, the transfer address will jump to the
wrap_to address specified by wrap_to register, and only 2 link-list nodes
can do a cyclic transfer to transfer data from DDR to IRAM.
Thus this patch adds wrap address to support this case.
[Baolin Wang changes the commit message]
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/85a5484bc1f3dd53ce6f92700ad8b35f30a0b096.1571812029.git.baolin.wang@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If we terminate the channel to free all descriptors associated with this
channel, we will leak the memory of current descriptor if the current
descriptor is not completed, since it had been deteled from the desc_issued
list and have not been added into the desc_completed list.
Thus we should check if current descriptor is completed or not, when freeing
the descriptors associated with one channel, if not, we should free it to
avoid this issue.
Fixes: 9b3b8171f7 ("dmaengine: sprd: Add Spreadtrum DMA driver")
Reported-by: Zhenfang Wang <zhenfang.wang@unisoc.com>
Tested-by: Zhenfang Wang <zhenfang.wang@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/170dbbc6d5366b6fa974ce2d366652e23a334251.1570609788.git.baolin.wang@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We will set the link-list pointer register point to next link-list
configuration's physical address, which can load DMA configuration
from the link-list node automatically.
But the link-list node's physical address can be larger than 32bits,
and now Spreadtrum DMA driver only supports 32bits physical address,
which may cause loading a incorrect DMA configuration when starting
the link-list transfer mode. According to the DMA datasheet, we can
use SRC_BLK_STEP register (bit28 - bit31) to save the high bits of the
link-list node's physical address to fix this issue.
Fixes: 4ac6954647 ("dmaengine: sprd: Support DMA link-list mode")
Signed-off-by: Zhenfang Wang <zhenfang.wang@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/eadfe9295499efa003e1c344e67e2890f9d1d780.1568267061.git.baolin.wang@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For the Spreadtrum DMA link-list mode, when the DMA engine got a slave
hardware request, which will trigger the DMA engine to load the DMA
configuration from the link-list memory automatically. But before the
slave hardware request, the slave will get an incorrect residue due
to the first node used to trigger the link-list was configured as the
last source address and destination address.
Thus we should make sure the first node was configured the start source
address and destination address, which can fix this issue.
Fixes: 4ac6954647 ("dmaengine: sprd: Support DMA link-list mode")
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/77868edb7aff9d5cb12ac3af8827ef2e244441a6.1567150471.git.baolin.wang@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For 2-stage transfer, some users like Audio still need transaction interrupt
to notify when the 2-stage transfer is completed. Thus we should enable
2-stage transfer interrupt to support this feature.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move the 2-stage configuration before configuring the link-list mode,
since we will use some 2-stage configuration to fill the link-list
configuration.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The maximum value of block length is 0xffff, so if the configured transfer length
is more than 0xffff, that will cause block length overflow to lead a configuration
error.
Thus we can set block length as the maximum burst length to avoid this issue, since
the maximum burst length will not be a big value which is more than 0xffff.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 2-stage destination channel will be triggered by source channel
automatically, which means we should not trigger it by software request.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When user terminates one DMA channel to free all its descriptors, but
at the same time one transaction interrupt was triggered possibly, now
we should not handle this interrupt by validating if the 'schan->cur_desc'
was set as NULL to avoid crashing the kernel.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We will get a NULL virtual descriptor by vchan_find_desc() when the descriptor
has been submitted, that will crash the kernel when getting the descriptor
status.
In this case, since the descriptor has been submitted to process, but it
is not completed now, which means the descriptor is listed into the
'vc->desc_submitted' list now. So we can not get current processing descriptor
by vchan_find_desc(), but the pointer 'schan->cur_desc' will point to the
current processing descriptor, then we can use 'schan->cur_desc' to get
current processing descriptor's status to avoid this issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We will describe the slave id in DMA cell specifier instead of DMA channel
id, thus we should save the slave id from DMA engine translation function,
and remove the channel id validation.
Meanwhile we do not need set default slave id in sprd_dma_alloc_chan_resources(),
remove it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add me as one of the module authors.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Spreadtrum DMA controller supports channel 2-stage tansfer mode,
that means we can request 2 dma channels, one for source channel, and
another one for destination channel. Once the source channel's transaction
is done, it will trigger the destination channel's transaction automatically
by hardware signal.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Spreadtrum DMA link-list mode is always one cyclic transfer,
so we should clear the SPRD_DMA_LLIST_END flag for the link-list
configuration. Moreover add cyclic callback support for the cyclic
transfer.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It will be failed to start one new transfer if the channel started one
none interrupt transfer before, since we will only set the schan->cur_desc
as NULL depending on the transfer interrupt now. Thus we should set
schan->cur_desc as NULL when free or terminate one dma channel to
avoid this issue.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We will pass sglen as 0 configure the last link-list configuration
when filling the descriptor, which will cause the incorrect link-list
configuration. Thus we should check if the sglen is 0 to configure
the correct link-list configuration.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add one field to save the transfer direction for struct sprd_dma_desc,
which is used to get correct transfer residue depending on the transfer
direction.
[Baolin Wang adds one field to present the transfer direction]
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The direction field of struct dma_slave_config was marked deprecated,
thus remove the usage.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Spreadtrum DMA can support the link-list transaction mode, which means
DMA controller can do transaction one by one automatically once we linked
these transaction by link-list register.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Updates to sprd, bam_dma, stm drivers.
- removal of VLAs in dmatest.
- Move TI drivers its own subdir.
- Switch to SPDX tags for ima/mxs dma drivers.
- Simplify getting .drvdata on bunch of drivers by Wolfram Sang.
-----BEGIN PGP SIGNATURE-----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=8mGV
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- updates to sprd, bam_dma, stm drivers
- remove VLAs in dmatest
- move TI drivers to their own subdir
- switch to SPDX tags for ima/mxs dma drivers
- simplify getting .drvdata on bunch of drivers by Wolfram Sang
* tag 'dmaengine-4.18-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (32 commits)
dmaengine: sprd: Add Spreadtrum DMA configuration
dmaengine: sprd: Optimize the sprd_dma_prep_dma_memcpy()
dmaengine: imx-dma: Switch to SPDX identifier
dmaengine: mxs-dma: Switch to SPDX identifier
dmaengine: imx-sdma: Switch to SPDX identifier
dmaengine: usb-dmac: Document R8A7799{0,5} bindings
dmaengine: qcom: bam_dma: fix some doc warnings.
dmaengine: qcom: bam_dma: fix invalid assignment warning
dmaengine: sprd: fix an NULL vs IS_ERR() bug
dmaengine: sprd: Use devm_ioremap_resource() to map memory
dmaengine: sprd: Fix potential NULL dereference in sprd_dma_probe()
dmaengine: pl330: flush before wait, and add dev burst support.
dmaengine: axi-dmac: Request IRQ with IRQF_SHARED
dmaengine: stm32-mdma: fix spelling mistake: "avalaible" -> "available"
dmaengine: rcar-dmac: Document R-Car D3 bindings
dmaengine: sprd: Move DMA request mode and interrupt type into head file
dmaengine: sprd: Define the DMA data width type
dmaengine: sprd: Define the DMA transfer step type
dmaengine: ti: New directory for Texas Instruments DMA drivers
dmaengine: shdmac: Change platform check to CONFIG_ARCH_RENESAS
...
This patch adds the 'device_config' and 'device_prep_slave_sg' interfaces
for users to configure DMA, as well as adding one 'struct sprd_dma_config'
structure to save Spreadtrum DMA configuration for each DMA channel.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is one preparation patch, we can use default DMA configuration to
implement the device_prep_dma_memcpy() interface instead of issuing
sprd_dma_config().
We will implement one new sprd_dma_config() function with introducing
device_prep_slave_sg() interface in following patch. So we can remove
the obsolete sprd_dma_config() firstly.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We recently cleaned this code up but we need to update the error
handling as well. The devm_ioremap_resource() returns error pointers on
error, never NULL.
Fixes: e7f063ae1a ("dmaengine: sprd: Use devm_ioremap_resource() to map memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of checking the return value of platform_get_resource(), we can
use devm_ioremap_resource() which has the NULL pointer check and the
memory region requesting.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Fixes: 9b3b8171f7 ("dmaengine: sprd: Add Spreadtrum DMA driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch will move the Spreadtrum DMA request mode and interrupt type
into one head file for user to configure.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Define the DMA data width type to make code more readable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Define the DMA transfer step type to make code more readable.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Sparse warns that 'sprd_dma_prep_dma_memcpy' should be static so make it
static.
drivers/dma/sprd-dma.c:713:32: warning:
symbol'sprd_dma_prep_dma_memcpy' was not declared. Should it be static?
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the DMA controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Eric Long
Vinod Koul
Baolin Wang
Zhenfang Wang
Eric Long
Linus Torvalds
Kees Cook
Dan Carpenter
Wei Yongjun
Vinod Koul
Baolin Wang