Introduce support for Geneve flow specification and allow
the creation of rules that are matching on basic Geneve
protocol fields: VNI, OAM bit, protocol type, options length.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow table supports three types of miss action:
1. Default miss action - go to default miss table according to table.
2. Go to specific table.
3. Switch domain - go to the root table of an alternative steering
table domain.
New table miss action was added - switch_domain.
The next domain for RDMA_RX namespace is the NIC RX domain.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add new flow steering namespace - MLX5_FLOW_NAMESPACE_RDMA_RX.
Flow steering rules in this namespace are used to filter
RDMA traffic.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. To workaround that limitation untagged packets will be
tagged with VLAN ID 0x000 (priority tag) and pop/push actions will be
replaced by VLAN re-write actions (which are supported by the HW).
Introduce prio tag mode as a pre-step to controlling the workaround
behavior.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding the TIR ICM address to the create_tir command outbox
through which the device reports the ICM address of the newly
created TIR.
The TIR address can be used for direct attachment to a steering
rule in SW managed steering mode.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add SW ICM related fields to the device memory capabilities
structure and sw ownership capability in flow table properties.
The currently supported SW ICM types are steering and header modify
and the changes exposes the device memory capabilities for each
of these two types.
SW ICM memory can be allocated by SW and then be accessed by RDMA
operations for direct management of the HW packet handling tables.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlyOup0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGHKoIAIKVuBSyD+m65TaM
pjoAFa56weEc67Mmai2A84EOm0MVy9C6L7EOcOgVsJiLxDCYyWQ7xYwV2kceKJpW
H5xauhb3+TxpxYeaeKdPPPHmBdejRwOPYvGAfnDMCqCCWQTad52sQUPCLI+yhF1t
wgnuMi+SwNBWP9aYCXdFPK4fVhh27AcEAOEsRVCh4tIBH/wkf4GwrDr3IX1MFeMX
jE/R43la4hu1swcWBsjkErWUasVPCgJSSQTfKDo9PQTVnoh0PHFp4fkOInVKLymQ
7AGo+Knc+1he+sFsB2IbZwea0xqtJtjtr1oC+at8gNx66qVG+o7UZNi5LR1uPW4Z
4+dwGBk=
=pyXR
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into mlx5-next
Linux 5.1-rc1
We forgot to reset the branch last merge window thus mlx5-next is outdated
and still based on 5.0-rc2. This merge commit is needed to sync mlx5-next
branch with 5.1-rc1.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Maxim, Remove un-used macros and spinlock from mlx5 code.
2) From Aya, Expose Management PCIE info register layout and add rate limit
print macros.
3) From Tariq, Compilation warning fix in fs_core.c
4) From Vu, Huy and Saeed, Improve mlx5 initialization flow:
The goal is to provide a better logical separation of mlx5 core
device initialization flow and will help to seamlessly support
creating different mlx5 device types such as PF, VF and SF
mlx5 sub-function virtual devices.
Mlx5_core driver needs to separate HCA resources from pci resources.
Its initialize/load/unload will be broken into stages:
1. Initialize common data structures
2. Setup function which initializes pci resources (for PF/VF)
or some other specific resources for virtual device
3. Initialize software objects according to hardware capabilities
4. Load all mlx5_core components
It is also necessary to detach mlx5_core mdev name/message from pci
device mdev->pdev name/message for a clearer report/debug of
different mlx5 device types.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Expose PRM layout for handling MPEIN (Management PCIE Info). It will be
used in the downstream patch for querying MPEIN via the driver.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add VLAN ID rewrite fields as a pre-step to support this rewrite.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When using the device packet encapsulation offload, the device
calculates an entropy value, representing the inner packet headers. The
entropy field is placed inside the outer packet headers. For UDP-type
encapsulations, the entropy is placed in the source port field of the
UDP header. For GRE-type encapsulations, the entropy is placed in the 8
LSB of the key field in the GRE header. If the device does not recognize
the encapsulation type, the entropy is not placed in the packet.
Entropy setting can be controlled using PCMR register. if encapsulation
offload is not used force_entropy_cap should be set to 0x0. Entropy
setting is enabled/disabled using entropy_calc, and could be
additionally enabled/disabled for GRE encapsulation by entropy_gre_calc.
As a pre-step to automatically control the tunnel entropy, introduce
the entropy fields in the PCMR register with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
ECPF connects to the eswitch through vport 0xfffe. ECPF may or may
not be the eswitch manager depending on firmware configuration.
1. If ECPF is eswitch manager: ECPF will take over the eswitch manager
responsibility. A rep of the host PF shall be created at the ECPF
side for the eswitch manager to control.
2. If ECPF is not eswitch manager: host PF will be the eswitch manager,
ECPF acts similar as a VF to the host PF. Host PF will be aware
of the ECPF vport presence and control it's rep.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Register Port Type and Speed (PTYS) introduces three new fields
extending the speed/protocols the can be reported and configured.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The QUERY_HOST_PARAMS command is used by an Embedded CPU Physical
Function (ECPF) driver to identify and retrieve information about the
PF on the host side. E.g, number of virtual functions and PCI BDF.
The number of VFs can be changed on the fly, a function is added to
query current number of VFs and will be used in downstream patches.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With the introduction of ECPF, we require that the ECPF driver will
aways call enable/disable HCA for that PF in the same way a PF does
this for its VFs. The PF is still responsible for calling enable and
disable HCA for its VFs.
To distinguish between the ECPF executing enable/disable HCA for
itself or for the PF, it sets the embedded CPU function bit in the
input params struct of these commands. When the bit is cleared and
function ID is zero, it refers to the peer PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Mellanox's SmartNIC combines embedded CPU(e.g, ARM) processing power
with advanced network offloads to accelerate a multitude of security,
networking and storage applications.
With the introduction of the SmartNIC, there is a new PCI function
called Embedded CPU Physical Function(ECPF). And it's possible for a
PF to get its ICM pages from the ECPF PCI function. Driver shall
identify if it is running on such a function by reading a bit in
the initialization segment.
When firmware asks for pages, it would issue a page request event
specifying how many pages it requests and for which function. That
driver responds with a manage_pages command providing the requested
pages along with an indication for which function it is providing these
pages.
The encoding before this patch was as follows:
function_id == 0: pages are requested for the function receiving
the EQE.
function_id != 0: pages are requested for VF identified by the
function_id value
A new one bit field in the EQE identifies that pages are requested for
the ECPF.
The notion of page_supplier can be introduced here and to support that,
manage pages and query pages were modified so firmware can distinguish
the following cases:
1. Function provides pages for itself
2. PF provides pages for its VF
3. ECPF provides pages to itself
4. ECPF provides pages for another function
This distinction is possible through the introduction of the bit
"embedded_cpu_function" in query_pages, manage_pages and page request
EQE.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To avoid compatibility issue with older kernels the firmware doesn't
allow SRQ to work with ODP unless kernel asks for it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The device capabilities for ODP structure was missing the field for XRC
transport so add it here.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting to
get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4, mlx5,
qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use write()
for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into
a big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and sysfs
files
- First steps toward removing 'uobject' from the view of the drivers
-----BEGIN PGP SIGNATURE-----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=T0p1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting
to get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4,
mlx5, qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use
write() for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into a
big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page
tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and
sysfs files
- First steps toward removing 'uobject' from the view of the drivers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (193 commits)
RDMA/srpt: Use kmem_cache_free() instead of kfree()
RDMA/mlx5: Signedness bug in UVERBS_HANDLER()
IB/uverbs: Signedness bug in UVERBS_HANDLER()
IB/mlx5: Allocate the per-port Q counter shared when DEVX is supported
IB/umad: Start using dev_groups of class
IB/umad: Use class_groups and let core create class file
IB/umad: Refactor code to use cdev_device_add()
IB/umad: Avoid destroying device while it is accessed
IB/umad: Simplify and avoid dynamic allocation of class
IB/mlx5: Fix wrong error unwind
IB/mlx4: Remove set but not used variable 'pd'
RDMA/iwcm: Don't copy past the end of dev_name() string
IB/mlx5: Fix long EEH recover time with NVMe offloads
IB/mlx5: Simplify netdev unbinding
IB/core: Move query port to ioctl
RDMA/nldev: Expose port_cap_flags2
IB/core: uverbs copy to struct or zero helper
IB/rxe: Reuse code which sets port state
IB/rxe: Make counters thread safe
IB/mlx5: Use the correct commands for UMEM and UCTX allocation
...
During testing the command format was changed to close a security
hole. Revise the driver to use the command format that will actually be
supported in GA firmware.
Both the UMEM and UCTX are intended only for use by the kernel and cannot
be executed using a general command.
Since the UMEM and CTX are not part of the general object the caps bits
were moved to be some log_xxx location in the general HCA caps.
The firmware code was adapted as well to match the above.
Fixes: a8b92ca1b0 ("IB/mlx5: Introduce DEVX")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates taken for dependencies on following patches.
* branche 'mlx5-next': (23 commits)
IB/mlx5: Introduce uid as part of alloc/dealloc transport domain
net/mlx5: Add shared Q counter bits
net/mlx5: Continue driver initialization despite debugfs failure
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
net/mlx5: Remove the get protocol device interface entry
net/mlx5: Support extended destination format in flow steering command
net/mlx5: E-Switch, Change vhca id valid bool field to bit flag
net/mlx5: Introduce extended destination fields
net/mlx5: Revise gre and nvgre key formats
net/mlx5: Add monitor commands layout and event data
net/mlx5: Add support for plugged-disabled cable status in PME
net/mlx5: Add support for PCIe power slot exceeded error in PME
net/mlx5: Rework handling of port module events
net/mlx5: Move flow counters data structures from flow steering header
...
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce uid as part of alloc/dealloc transport domain to match the
device specification.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Updated HW specification file with needed bits to allow
sharing of Q counters between DEVX contexts and kernel.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
mlx5-next shared branch with rdma subtree to avoid mlx5 rdma v.s. netdev
conflicts.
Highlights:
1) Lag refactroing and flow counter affinity bits.
2) mlx5 core cleanups
By Roi Dayan (2) and others
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This dictates the device affinity for eswitch flow counters, set by the FW
according to the HW device capabilities.
Under "source eswitch" affinity, the counter should be allocated on the
device related to the source vport in the match. This covers both non
merged e-switch mode as well as old FW that does not advertise this cap.
Under "flow eswitch" affinity, the counter should be allocated on the
device where the eswitch rule is set.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Apparently gcc is cool with upper case '0X' but it is not commonly used.
Replace '0X' with lowercase '0x' in mlx5_ifc.h file.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cap bits locations for the fdb caps of multi path to table (used for
local mirroring) and multi encap (used for prio/chains) were wrongly used
in swapped locations. This went unnoted so far b/c we tested the offending
patch with CX5 FW that supports both of them. On different environments where
not both caps are supported, we will be messed up, fix that.
Fixes: b9aa0ba17a ('net/mlx5: Add cap bits for multi fdb encap')
Signed-off-by: Vu Pham <vu@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PPCNT is not supported if PCAM access reg is supported and ppcnt bit is clear.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Extended destinations provide the ability to configure different
encapsulation properties per destination on a single FTE. This is
needed for use-cases such as remote mirroring over tunneled networks.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
GRE RFC defines a 32 bit key field. NVGRE RFC splits the 32 bit
key field to 24 bit VSID (gre_key_h) and 8 bit flow entropy (gre_key_l).
Define the two key parsing alternatives in a union, thus enabling both
access methods.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Will be used in downstream patch to monitor counter changes
by the HCA and report it to the driver by an event.
The driver will update its counters cached data accordingly.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Danit Goldberg says:
Packet based credit mode
Packet based credit mode is an alternative end-to-end credit mode for QPs
set during their creation. Credits are transported from the responder to
the requester to optimize the use of its receive resources. In
packet-based credit mode, credits are issued on a per packet basis.
The advantage of this feature comes while sending large RDMA messages
through switches that are short in memory.
The first commit exposes QP creation flag and the HCA capability. The
second commit adds support for a new DV QP creation flag. The last commit
report packet based credit mode capability via the MLX5DV device
capabilities.
* branch 'mlx5-packet-credit-fc':
IB/mlx5: Report packet based credit mode device capability
IB/mlx5: Add packet based credit mode support
net/mlx5: Expose packet based credit mode
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Packet based credit mode bit determines whether the credit mode
is done per message or packet. Expose the QP creation flag and
the HCA capability.
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Update the supported DEVX commands, it includes adding to the
query/modify command's list and to the encoding handling.
In addition, a valid range for general commands was added to be used for
future commands.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Expose device capabilities for DEVX user context, it includes which caps
the device is supported and a matching bit to set as part of user
context creation.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Fix wrong offsets of reserved fields in ifc file.
Issues found using pahole.
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adapt XRC SRQ to the latest HW specification with fixed definition
around umem valid bits. The previous definition relied on a bit which
was taken for other purposes in legacy FW.
Fixes: bd37197554 ("net/mlx5: Update mlx5_ifc with DEVX UID bits")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Added "Per lane raw errors" capability bit in
Ports Capabilities Mask (PCAM) enhanced features
layout.
This bit determines if the fields "phy_raw_errors_laneX"
in "Physical Layer statistical" counters group are supported.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added FEC related fields to PPLM layout.
These fields are needed to set and query FEC policy
for different link speeds.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If set, the firmware supports creating of flow tables with encap
enabled while VFs are configured, if we already created one
(restriction still applies on the first creation).
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 updates for both net-next and rdma-next
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux: (21 commits)
net/mlx5: Expose DC scatter to CQE capability bit
net/mlx5: Update mlx5_ifc with DEVX UID bits
net/mlx5: Set uid as part of DCT commands
net/mlx5: Set uid as part of SRQ commands
net/mlx5: Set uid as part of SQ commands
net/mlx5: Set uid as part of RQ commands
net/mlx5: Set uid as part of QP commands
net/mlx5: Set uid as part of CQ commands
net/mlx5: Rename incorrect naming in IFC file
net/mlx5: Export packet reformat alloc/dealloc functions
net/mlx5: Pass a namespace for packet reformat ID allocation
net/mlx5: Expose new packet reformat capabilities
{net, RDMA}/mlx5: Rename encap to reformat packet
net/mlx5: Move header encap type to IFC header file
net/mlx5: Break encap/decap into two separated flow table creation flags
net/mlx5: Add support for more namespaces when allocating modify header
net/mlx5: Export modify header alloc/dealloc functions
net/mlx5: Add proper NIC TX steering flow tables support
net/mlx5: Cleanup flow namespace getter switch logic
net/mlx5: Add memic command opcode to command checker
...
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
dc_req_scat_data_cqe capability bit determines
if requester scatter to cqe is available for 64 bytes CQE over
DC transport type.
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Reviewed-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Today mlx5 devices support two teardown modes:
1- Regular teardown
2- Force teardown
This change introduces the enhanced version of the "Force teardown" that
allows SW to perform teardown in a faster way without the need to reclaim
all the pages.
Fast teardown provides the following advantages:
1- Fix a FW race condition that could cause command timeout
2- Avoid moving to polling mode
3- Close the vport to prevent PCI ACK to be sent without been scatter
to memory
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add DEVX information to WQ, SRQ, CQ, TIR, TIS, QP,
RQ, XRCD, PD, MKEY and MCG.
Each object that is created/destroyed/modified via verbs will
be stamped with a UID based on its user context. This is already
done for DEVX objects commands.
This will enable the firmware to enforce the usage of kernel objects
from the DEVX flow by validating that the same UID is used and the
resources are really related to the same user.
The addition of *_valid fields are needed to distinguish
how various addresses are passed.
For non-DEVX callers, all those fields will be zero.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Set uid as part of DCT commands so that the firmware can manage the
DCT object in a secured way.
That will enable using a DCT that was created by verbs application
to be used by the DEVX flow in case the uid is equal.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Set uid as part of SRQ commands so that the firmware can manage the
SRQ object in a secured way.
That will enable using an SRQ that was created by verbs application
to be used by the DEVX flow in case the uid is equal.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Set uid as part of SQ commands so that the firmware can manage the
SQ object in a secured way.
That will enable using an SQ that was created by verbs application
to be used by the DEVX flow in case the uid is equal.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Set uid as part of RQ commands so that the firmware can manage the
RQ object in a secured way.
That will enable using an RQ that was created by verbs application
to be used by the DEVX flow in case the uid is equal.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Set uid as part of QP commands so that the firmware can manage the
QP object in a secured way.
That will enable using a QP that was created by verbs application to
be used by the DEVX flow in case the uid is equal.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Set uid as part of CQ commands so that the firmware can manage the CQ
object in a secured way.
The firmware should mark this CQ with the given uid so that it can
be used later on only by objects with the same uid.
Upon DEVX flows that use this CQ (e.g. create QP command), the
pointed CQ must have the same uid as of the issuer uid command.
When a command is issued with uid=0 it means that the issuer of the
command is trusted (i.e. kernel), in that case any pointed object
can be used regardless of its uid.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Remove a trailing underscore from the multicast/unicast names.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Expose new abilities when creating a packet reformat context.
The new types which can be created are:
MLX5_REFORMAT_TYPE_L2_TO_L2_TUNNEL: Ability to create generic encap
operation to be done by the HW.
MLX5_REFORMAT_TYPE_L3_TUNNEL_TO_L2: Ability to create generic decap
operation where the inner packet doesn't contain L2.
MLX5_REFORMAT_TYPE_L2_TO_L3_TUNNEL: Ability to create generic encap
operation to be done by the HW. The L2 of the original packet
is dropped.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Renames all encap mlx5_{core,ib} code to use the new naming of packet
reformat. This change doesn't introduce any function change and is
needed to properly reflect the operation being done by this action.
For example not only can we encapsulate a packet, but also decapsulate it.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Those bits are hardware specification and should be defined in the
IFC header file.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
rdma.git merge resolution for the 4.19 merge window
Conflicts:
drivers/infiniband/core/rdma_core.c
- Use the rdma code and revise with the new spelling for
atomic_fetch_add_unless
drivers/nvme/host/rdma.c
- Replace max_sge with max_send_sge in new blk code
drivers/nvme/target/rdma.c
- Use the blk code and revise to use NULL for ib_post_recv when
appropriate
- Replace max_sge with max_recv_sge in new blk code
net/rds/ib_send.c
- Use the net code and revise to use NULL for ib_post_recv when
appropriate
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltwm2geHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGITkH/iSzkVhT2OxHoir0
mLVzTi7/Z17L0e/ELl7TvAC0iLFlWZKdlGR0g3b4/QpXLPmNK4HxiDRTQuWn8ke0
qDZyDq89HqLt+mpeFZ43PCd9oqV8CH2xxK3iCWReqv6bNnowGnRpSStlks4rDqWn
zURC/5sUh7TzEG4s997RrrpnyPeQWUlf/Mhtzg2/WvK2btoLWgu5qzjX1uFh3s7u
vaF2NXVJ3X03gPktyxZzwtO1SwLFS1jhwUXWBZ5AnoJ99ywkghQnkqS/2YpekNTm
wFk80/78sU+d91aAqO8kkhHj8VRrd+9SGnZ4mB2aZHwjZjGcics4RRtxukSfOQ+6
L47IdXo=
=sJkt
-----END PGP SIGNATURE-----
Merge tag 'v4.18' into rdma.git for-next
Resolve merge conflicts from the -rc cycle against the rdma.git tree:
Conflicts:
drivers/infiniband/core/uverbs_cmd.c
- New ifs added to ib_uverbs_ex_create_flow in -rc and for-next
- Merge removal of file->ucontext in for-next with new code in -rc
drivers/infiniband/core/uverbs_main.c
- for-next removed code from ib_uverbs_write() that was modified
in for-rc
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Modify and query vport state commands share the same admin_state and
op_mod values, rename the enums to fit them both.
In addition, remove the esw prefix from the admin state enum as this
also applied for vnic.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware has defined new HCA capability field called "max_num_eqs",
that is the number of available EQs after subtracting reserved FW EQs.
Before this capability the FW reported the EQ number in "log_max_eqs",
the reported value also contained FW reserved EQs, but the driver might
be failing to load on 320 cpus systems due to the fact that FW
reserved EQs were not available to the driver.
Now the driver has to obtain max_num_eqs value from new FW to get real
number of EQs available.
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC has a limited number of offloaded VXLAN UDP ports (usually 4).
Instead of letting the firmware fail when trying to add more ports than
it can handle, let the driver check it on its own.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux.git
This is required to resolve dependencies of the next series of RDMA
patches.
* branch 'mellanox/mlx5-next':
net/mlx5: Add support for flow table destination number
net/mlx5: Add forward compatible support for the FTE match data
net/mlx5: Fix tristate and description for MLX5 module
net/mlx5: Better return types for CQE API
net/mlx5: Use ERR_CAST() instead of coding it
net/mlx5: Add missing SET_DRIVER_VERSION command translation
net/mlx5: Add XRQ commands definitions
net/mlx5: Add core support for double vlan push/pop steering action
net/mlx5: Expose MPEGC (Management PCIe General Configuration) structures
net/mlx5: FW tracer, add hardware structures
net/mlx5: fix uaccess beyond "count" in debugfs read/write handlers
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support to set a destination from a flow table number.
This functionality will be used in downstream patches from this
series by the DEVX stuff.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
mlx5 core infrastructure updates and fixes.
From Eran:
- Add MPEGC (Management PCIe General Configuration) registers and btis
- Fix tristate and description for MLX5 module
rom Feras:
- Add hardware structures for the firmware tracer
From Jainbo:
- Core support for double vlan push/pop steering action
From Max:
- Add XRQ commands definitions
From Noa:
- Add missing SET_DRIVER_VERSION command translation
From Roi:
- Use ERR_CAST() instead of coding it
From Tariq:
- Better return types for CQE API
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As newer firmware supports double push/pop in a single FTE, we add
core bits and extend vlan action logic for it.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch exposes PRM layout for handling MPEGC (Management PCIe
General Configuration).
This will be used in the downstream patch for configuring MPEGC via the
driver.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This change adds the infrastructure to mlx5 core fw tracer.
It introduces the following 4 new registers:
MLX5_REG_MTRC_CAP - Used to read tracer capabilities
MLX5_REG_MTRC_CONF - Used to set tracer configurations
MLX5_REG_MTRC_STDB - Used to query tracer strings database
MLX5_REG_MTRC_CTRL - Used to control the tracer
The capability of the tracing can be checked using mcam access
register, therefore, the mcam access register interface will expose
the tracer register.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For dependencies, branch based on 'mellanox/mlx5-next' of
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux.git
Pull Dump and fill MKEY from Leon Romanovsky:
====================
MLX5 IB HCA offers the memory key, dump_fill_mkey to increase performance,
when used in a send or receive operations.
It is used to force local HCA operations to skip the PCI bus access, while
keeping track of the processed length in the ibv_sge handling.
In this three patch series, we expose various bits in our HW spec
file (mlx5_ifc.h), move unneeded for mlx5_core FW command and export such
memory key to user space thought our mlx5-abi header file.
====================
Botched auto-merge in mlx5_ib_alloc_ucontext() resolved by hand.
* branch 'mlx5-dump-fill-mkey':
IB/mlx5: Expose dump and fill memory key
net/mlx5: Add hardware definitions for dump_fill_mkey
net/mlx5: Limit scope of dump_fill_mkey function
net/mlx5: Rate limit errors in command interface
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
MLX5 IB HCA offers the memory key, dump_fill_mkey to boost
performance by forcing local HCA operations to skip the PCI bus
access,
This patch adds needed hardware definitions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the FW will err on driver attempts to deal with
setting/unsetting the eswitch and as a result the overall setup
of sriov will fail.
Fix that by avoiding the operation if e-switch management is not
allowed for this driver instance. While here, move to use the
correct name for the esw manager capability name.
Fixes: 81848731ff ('net/mlx5: E-Switch, Add SR-IOV (FDB) support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Guy Kushnir <guyk@mellanox.com>
Reviewed-by: Eli Cohen <eli@melloanox.com>
Tested-by: Eli Cohen <eli@melloanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For dependencies, branch based on 'mellanox/mlx5-next' of
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux.git
Pull RoCE ICRC counters from Leon Romanovsky:
====================
This series exposes RoCE ICRC counter through existing RDMA hw_counters
sysfs interface.
The first patch has all HW definitions in mlx5_ifc.h file and second patch
is the actual counter implementation.
====================
* branch 'icrc-counter':
IB/mlx5: Support RoCE ICRC encapsulated error counter
net/mlx5: Add RoCE RX ICRC encapsulated counter
Add capability bit in PCAM register and RoCE ICRC error counter
to PPCNT register.
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Add support to register a memory with the firmware via the DEVX
interface.
The driver translates a given user address to ib_umem then it will
register the physical addresses with the firmware and get a unique id
for this registration to be used for this virtual address.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support in DEVX for modify and query commands, the required lock is
taken (i.e. READ/WRITE) by the KABI infrastructure accordingly.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch updates the mlx5_ifc structures and
command interface to support DEVX.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This has been a quiet cycle for RDMA, the big bulk is the usual smallish
driver updates and bug fixes. About four new uAPI related things. Not as much
Szykaller patches this time, the bugs it finds are getting harder to fix.
- More work cleaning up the RDMA CM code
- Usual driver bug fixes and cleanups for qedr, qib, hfi1, hns, i40iw, iw_cxgb4, mlx5, rxe
- Driver specific resource tracking and reporting via netlink
- Continued work for name space support from Parav
- MPLS support for the verbs flow steering uAPI
- A few tricky IPoIB fixes improving robustness
- HFI1 driver support for the '16B' management packet format
- Some auditing to not print kernel pointers via %llx or similar
- Mark the entire 'UCM' user-space interface as BROKEN with the intent to remove it
entirely. The user space side of this was long ago replaced with RDMA-CM and
syzkaller is finding bugs in the residual UCM interface nobody wishes to fix because
nobody uses it.
- Purge more bogus BUG_ON's from Leon
- 'flow counters' verbs uAPI
- T10 fixups for iser/isert, these are Acked by Martin but going through the RDMA
tree due to dependencies
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Mb8m
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a quiet cycle for RDMA, the big bulk is the usual
smallish driver updates and bug fixes. About four new uAPI related
things. Not as much Szykaller patches this time, the bugs it finds are
getting harder to fix.
Summary:
- More work cleaning up the RDMA CM code
- Usual driver bug fixes and cleanups for qedr, qib, hfi1, hns,
i40iw, iw_cxgb4, mlx5, rxe
- Driver specific resource tracking and reporting via netlink
- Continued work for name space support from Parav
- MPLS support for the verbs flow steering uAPI
- A few tricky IPoIB fixes improving robustness
- HFI1 driver support for the '16B' management packet format
- Some auditing to not print kernel pointers via %llx or similar
- Mark the entire 'UCM' user-space interface as BROKEN with the
intent to remove it entirely. The user space side of this was long
ago replaced with RDMA-CM and syzkaller is finding bugs in the
residual UCM interface nobody wishes to fix because nobody uses it.
- Purge more bogus BUG_ON's from Leon
- 'flow counters' verbs uAPI
- T10 fixups for iser/isert, these are Acked by Martin but going
through the RDMA tree due to dependencies"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (138 commits)
RDMA/mlx5: Update SPDX tags to show proper license
RDMA/restrack: Change SPDX tag to properly reflect license
IB/hfi1: Fix comment on default hdr entry size
IB/hfi1: Rename exp_lock to exp_mutex
IB/hfi1: Add bypass register defines and replace blind constants
IB/hfi1: Remove unused variable
IB/hfi1: Ensure VL index is within bounds
IB/hfi1: Fix user context tail allocation for DMA_RTAIL
IB/hns: Use zeroing memory allocator instead of allocator/memset
infiniband: fix a possible use-after-free bug
iw_cxgb4: add INFINIBAND_ADDR_TRANS dependency
IB/isert: use T10-PI check mask definitions from core layer
IB/iser: use T10-PI check mask definitions from core layer
RDMA/core: introduce check masks for T10-PI offload
IB/isert: fix T10-pi check mask setting
IB/mlx5: Add counters read support
IB/mlx5: Add flow counters read support
IB/mlx5: Add flow counters binding support
IB/mlx5: Add counters create and destroy support
IB/uverbs: Add support for flow counters
...
The FPGA queue pair (QP) event fires whenever a QP on the FPGA
transitions to the error state.
At this stage, this event is unrecoverable, it may become recoverable
in the future.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
Introduce new internal to mlx5 CQE format - mini-CQE. It is a CQE in
compressed form that holds data needed to extra a single full CQE.
It is a stride index, byte count and packet checksum.
====================
* mini_cqe:
IB/mlx5: Introduce a new mini-CQE format
IB/mlx5: Refactor CQE compression response
net/mlx5: Exposing a new mini-CQE format
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The new mini-CQE format includes byte-count, checksum
and stride index.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If set, the FDB table supports the forward action with a
destination list that includes a flow table.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add pbmc and pptb in the port_access_reg_cap_mask. These two
bits determine if device supports receive buffer configuration.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/fLEAAoJEEg/ir3gV/o+7jUH/3n5/Uw1LLt3TfeKArx6i0F1
3G4U5B0ha03qiDqXprwhyQ3I6lgYmRBmjcxnqmvcqOAqO4/hSsjtTR+A/mgbEDhJ
YtdekFNEX+72h/N2GIpZwChIWSE3EcMPaLYnV8TwLUgh9YSust2sCLSBbJCjxOKc
j78M8ept/bXZwTm/iJhEjtmqw0xl91rl011chCAua0iEpH3wxteDARmKABFHMQxl
I3N/x/e/astgcSCNgpO4uDf9zEIRkNdzcHPzSMJ6C2Oo5W9XiZEekfw7WKj9nXfa
G+eGckkAyCOQ/r2lZ9nA0ZUvQ2X6JISvxgohuaCNwTgsz3acTxbLnQK4YWHzQCQ=
=iHi6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux into for-next
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
* tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5e: Explicitly set source e-switch in offloaded TC rules
net/mlx5: Add source e-switch owner
net/mlx5e: Explicitly set destination e-switch in FDB rules
net/mlx5: Add destination e-switch owner
net/mlx5: Properly handle a vport destination when setting FTE
net/mlx5: Add merged e-switch cap
IB/mlx5: Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Eswitch, Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Vport, Use 'kvfree()' for memory allocated by 'kvzalloc()'
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/fLEAAoJEEg/ir3gV/o+7jUH/3n5/Uw1LLt3TfeKArx6i0F1
3G4U5B0ha03qiDqXprwhyQ3I6lgYmRBmjcxnqmvcqOAqO4/hSsjtTR+A/mgbEDhJ
YtdekFNEX+72h/N2GIpZwChIWSE3EcMPaLYnV8TwLUgh9YSust2sCLSBbJCjxOKc
j78M8ept/bXZwTm/iJhEjtmqw0xl91rl011chCAua0iEpH3wxteDARmKABFHMQxl
I3N/x/e/astgcSCNgpO4uDf9zEIRkNdzcHPzSMJ6C2Oo5W9XiZEekfw7WKj9nXfa
G+eGckkAyCOQ/r2lZ9nA0ZUvQ2X6JISvxgohuaCNwTgsz3acTxbLnQK4YWHzQCQ=
=iHi6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The source e-switch owner allows a vport on one e-switch port be associated
with a rule defined on the second port e-switch.
The role of the source eswitch owner valid bit in the flow group is to
allow the firmware fail driver attempts to wild card the source eswitch
match field. If this bit is not set, the firmware ignores the source
eswitch owner field totally.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The destination e-switch owner allows a rule in namespace of one e-switch
owner to point to a vport that is natively associated with another
e-switch owner.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
Under merged eswitch, both the matching on source vport and setting
destination vport can have a 2nd attribute which is the vhca id of the
eswitch owner.
For example:
esw0: {match: <src vport=1 owner=0> action: fwd to <dst vport=7, owner=1>}
is a flow set on eswitch0 matching on source vport=1 from his eswitch
and the action being fwd to dest vport=7 of eswitch1.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz Klein <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch reports the device's capbilities to offload
encapsulated MPLS tunnel protocols to user-space:
- Capability to offload MPLS over GRE.
- Capability to offload MPLS over UDP.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch introduces support for the MPLS flow spec and
allows the creation of rules that are matching on the
MPLS label.
Applying the rule matching depends on the flow specs order and
the location of the MPLS in the spec list as there are different
configurations to be made in the device in the cases of MPLSoGRE
and MPLSoUDP vs. non-encapsulated MPLS.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add routines for manipulating TLS TX offload contexts.
In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Add implementation for Innova TLS (FPGA-based) hardware.
These routines will be used by the TLS offload support in a later patch
mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.
In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix RDMA uapi headers to actually compile in userspace and be more
complete
- Three shared with netdev pull requests from Mellanox:
* 7 patches, mostly to net with 1 IB related one at the back). This
series addresses an IRQ performance issue (patch 1), cleanups related to
the fix for the IRQ performance problem (patches 2-6), and then extends
the fragmented completion queue support that already exists in the net
side of the driver to the ib side of the driver (patch 7).
* Mostly IB, with 5 patches to net that are needed to support the remaining
10 patches to the IB subsystem. This series extends the current
'representor' framework when the mlx5 driver is in switchdev mode from
being a netdev only construct to being a netdev/IB dev construct. The IB
dev is limited to raw Eth queue pairs only, but by having an IB dev of
this type attached to the representor for a switchdev port, it enables
DPDK to work on the switchdev device.
* All net related, but needed as infrastructure for the rdma driver
- Updates for the hns, i40iw, bnxt_re, cxgb3, cxgb4, hns drivers
- SRP performance updates
- IB uverbs write path cleanup patch series from Leon
- Add RDMA_CM support to ib_srpt. This is disabled by default. Users need to
set the port for ib_srpt to listen on in configfs in order for it to be
enabled (/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port)
- TSO and Scatter FCS support in mlx4
- Refactor of modify_qp routine to resolve problems seen while working on new
code that is forthcoming
- More refactoring and updates of RDMA CM for containers support from Parav
- mlx5 'fine grained packet pacing', 'ipsec offload' and 'device memory'
user API features
- Infrastructure updates for the new IOCTL interface, based on increased usage
- ABI compatibility bug fixes to fully support 32 bit userspace on 64 bit
kernel as was originally intended. See the commit messages for
extensive details
- Syzkaller bugs and code cleanups motivated by them
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ku8g
-----END PGP SIGNATURE-----
Merge tag 'for-linus-unmerged' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Doug and I are at a conference next week so if another PR is sent I
expect it to only be bug fixes. Parav noted yesterday that there are
some fringe case behavior changes in his work that he would like to
fix, and I see that Intel has a number of rc looking patches for HFI1
they posted yesterday.
Parav is again the biggest contributor by patch count with his ongoing
work to enable container support in the RDMA stack, followed by Leon
doing syzkaller inspired cleanups, though most of the actual fixing
went to RC.
There is one uncomfortable series here fixing the user ABI to actually
work as intended in 32 bit mode. There are lots of notes in the commit
messages, but the basic summary is we don't think there is an actual
32 bit kernel user of drivers/infiniband for several good reasons.
However we are seeing people want to use a 32 bit user space with 64
bit kernel, which didn't completely work today. So in fixing it we
required a 32 bit rxe user to upgrade their userspace. rxe users are
still already quite rare and we think a 32 bit one is non-existing.
- Fix RDMA uapi headers to actually compile in userspace and be more
complete
- Three shared with netdev pull requests from Mellanox:
* 7 patches, mostly to net with 1 IB related one at the back).
This series addresses an IRQ performance issue (patch 1),
cleanups related to the fix for the IRQ performance problem
(patches 2-6), and then extends the fragmented completion queue
support that already exists in the net side of the driver to the
ib side of the driver (patch 7).
* Mostly IB, with 5 patches to net that are needed to support the
remaining 10 patches to the IB subsystem. This series extends
the current 'representor' framework when the mlx5 driver is in
switchdev mode from being a netdev only construct to being a
netdev/IB dev construct. The IB dev is limited to raw Eth queue
pairs only, but by having an IB dev of this type attached to the
representor for a switchdev port, it enables DPDK to work on the
switchdev device.
* All net related, but needed as infrastructure for the rdma
driver
- Updates for the hns, i40iw, bnxt_re, cxgb3, cxgb4, hns drivers
- SRP performance updates
- IB uverbs write path cleanup patch series from Leon
- Add RDMA_CM support to ib_srpt. This is disabled by default. Users
need to set the port for ib_srpt to listen on in configfs in order
for it to be enabled
(/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port)
- TSO and Scatter FCS support in mlx4
- Refactor of modify_qp routine to resolve problems seen while
working on new code that is forthcoming
- More refactoring and updates of RDMA CM for containers support from
Parav
- mlx5 'fine grained packet pacing', 'ipsec offload' and 'device
memory' user API features
- Infrastructure updates for the new IOCTL interface, based on
increased usage
- ABI compatibility bug fixes to fully support 32 bit userspace on 64
bit kernel as was originally intended. See the commit messages for
extensive details
- Syzkaller bugs and code cleanups motivated by them"
* tag 'for-linus-unmerged' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (199 commits)
IB/rxe: Fix for oops in rxe_register_device on ppc64le arch
IB/mlx5: Device memory mr registration support
net/mlx5: Mkey creation command adjustments
IB/mlx5: Device memory support in mlx5_ib
net/mlx5: Query device memory capabilities
IB/uverbs: Add device memory registration ioctl support
IB/uverbs: Add alloc/free dm uverbs ioctl support
IB/uverbs: Add device memory capabilities reporting
IB/uverbs: Expose device memory capabilities to user
RDMA/qedr: Fix wmb usage in qedr
IB/rxe: Removed GID add/del dummy routines
RDMA/qedr: Zero stack memory before copying to user space
IB/mlx5: Add ability to hash by IPSEC_SPI when creating a TIR
IB/mlx5: Add information for querying IPsec capabilities
IB/mlx5: Add IPsec support for egress and ingress
{net,IB}/mlx5: Add ipsec helper
IB/mlx5: Add modify_flow_action_esp verb
IB/mlx5: Add implementation for create and destroy action_xfrm
IB/uverbs: Introduce ESP steering match filter
IB/uverbs: Add modify ESP flow_action
...
This change updates the mlx5 interface to create mkey
on the device.
The updates in the command mailbox include increasing the
access mode type field to 5 bits in order to support additional
types such as MLX5_MKC_ACCESS_MODE_MEMIC which represents device
memory access type and will be used when registering MR on allocated
device memory.
All the places that use the old access mode format are adjusted as
well.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch adds the mlx5_ib driver implementation for the device
memory allocation API.
It implements the ib_device callbacks for allocation and deallocation
operations as well as a new mmap command support which allows mapping
an allocated device memory to a VMA.
The change also adds reporting of device memory maximum size and
alignment parameters reported in device capabilities.
The allocation/deallocation operations are using new firmware
commands to allocate MEMIC memory on the device.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch adds querying of device memory capabilities by the mlx5_core
driver during initialization.
Device memory capabilities is a new capability type and structure
which contains the necessary data that is needed for future device
memory allocation.
The presence of this new capabilities struct is indicated in the
general capabilities struct which is queried first by the driver.
If the presence bit is set, the driver will also query the new
capabilities struct and save it in the device context.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Current Striding RQ HW feature utilizes the RX buffers so that
there is no wasted room between the strides. This maximises
the memory utilization.
This prevents the use of build_skb() (which requires headroom
and tailroom), and demands to memcpy the packets headers into
the skb linear part.
In this patch, whenever a set of conditions holds, we apply
an RQ configuration that allows combining the use of linear SKB
on top of a Striding RQ.
To use build_skb() with Striding RQ, the following must hold:
1. packet does not cross a page boundary.
2. there is enough headroom and tailroom surrounding the packet.
We can satisfy 1 and 2 by configuring:
stride size = MTU + headroom + tailoom.
This is possible only when:
a. (MTU - headroom - tailoom) does not exceed PAGE_SIZE.
b. HW LRO is turned off.
Using linear SKB has many advantages:
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
Some implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
UDP packet rate, early drop in TC layer:
--------------------------------------------
| pkt size | before | after | ratio |
--------------------------------------------
| 1500byte | 4.65 Mpps | 5.96 Mpps | 1.28x |
| 500byte | 5.23 Mpps | 5.97 Mpps | 1.14x |
| 64byte | 5.94 Mpps | 5.96 Mpps | 1.00x |
--------------------------------------------
TCP streams: ~20% gain
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In some firmware configuration, UMR usage from Virtual Functions is restricted.
This information is published to the driver using new capability bits.
Avoid using UMRs in these cases and use the Firmware slow-path flow to create
mkeys and populate them with Virtual to Physical address translation.
Older drivers that do not have this patch, will end up using memory keys that
aren't populated with Virtual to Physical address translation that is done
part of the UMR work.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Newer NICs (ConnectX-5 and onward) can apply vlan pop or push as an
action taking place during flow steering. Add the core bits for that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets dropped while vport down statistics:
Rx dropped while vport down - counts packets which were steered by
e-switch to a vport, but dropped since the vport was down. This counter
will be shown on ip link tool as part of the vport rx_dropped counter.
Tx dropped while vport down - counts packets which were transmitted by
a vport, but dropped due to vport logical link down. This counter
will be shown on ip link tool as part of the vport tx_dropped counter.
The counters are read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets drop counter:
Rx steering missed dropped packets - counts packets which were dropped
due to miss on NIC rx steering rules.
This counter will be shown on ethtool as a new counter called
rx_steer_missed_packets.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for new FW command QUERY_VNIC_ENV.
The command is used by the driver to query vnic diagnostic statistics
from FW.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement set/get functions to configure PFC stall prevention
timeout by tunables api through ethtool.
By default the stall prevention timeout is configured to 8 sec.
Timeout range is: 80-8000 msec.
Enabling stall prevention with the auto timeout will set
the timeout to 100 msec.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the needed capability bit and counters to device spec description.
Expose the following two counters in ethtool:
tx_pause_storm_warning_events: when the device is stalled for a period
longer than a pre-configured watermark, the counter increase, allowing
the debug utility an insight into current device status.
tx_pause_storm_error_events: when the device is stalled for a period
longer than a pre-configured timeout, the pause transmission is disabled,
and the counter increase.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add two new parameters: max_burst_sz and typical_pkt_size (both
in bytes) to rate limit configurations.
max_burst_sz: The device will schedule bursts of packets for an
SQ connected to this rate, smaller than or equal to this value.
Value 0x0 indicates packet bursts will be limited to the device
defaults. This field should be used if bursts of packets must be
strictly kept under a certain value.
typical_pkt_size: When the rate limit is intended for a stream of
similar packets, stating the typical packet size can improve the
accuracy of the rate limiter. The expected packet size will be
the same for all SQs associated with the same rate limit index.
Ethernet driver is updated according to this change, but these two
parameters will be kept as 0 due to lacking of proper way to get the
configurations from user space which requires to change
ndo_set_tx_maxrate interface.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add helper functions that check if a protocol is
part of a flow steering match criteria.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we don't support egress flow steering namespace in mlx5
flow steering core implementation. However, when we want to encrypt
a packet, we model it as a flow steering rule in the egress path.
To overcome this, we add an empty egress namespace to flow steering.
This namespace is initialized only when ipsec support exists.
In the future, this will grow to a full blown full steering
implementation, resembling the ingress path.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJabj6pAAoJEHm+PkMAQRiGs8cIAJQFkCWnbz86e3vG4DuWhyA8
CMGHCQdUOxxFGa/ixhIiuetbC0x+JVHAjV2FwVYbAQfaZB3pfw2iR1ncQxpAP1AI
oLU9vBEqTmwKMPc9CM5rRfnLFWpGcGwUNzgPdxD5yYqGDtcM8K840mF6NdkYe5AN
xU8rv1wlcFPF4A5pvHCH0pvVmK4VxlVFk/2H67TFdxBs4PyJOnSBnf+bcGWgsKO6
hC8XIVtcKCH2GfFxt5d0Vgc5QXJEpX1zn2mtCa1MwYRjN2plgYfD84ha0xE7J0B0
oqV/wnjKXDsmrgVpncr3txd4+zKJFNkdNRE4eLAIupHo2XHTG4HvDJ5dBY2NhGU=
=sOml
-----END PGP SIGNATURE-----
Merge tag v4.15 of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
To resolve conflicts in:
drivers/infiniband/hw/mlx5/main.c
drivers/infiniband/hw/mlx5/qp.c
From patches merged into the -rc cycle. The conflict resolution matches
what linux-next has been carrying.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Allow to specify the size of the hairpin queues along with the
packet buffer data size from the core setup code.
If the driver doesn't provide this, the FW applies proper value that
matches the provided data size and a FW chosen RQ stride size.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The latest merge between net and net-next introduced a complier assert in
mlx5 driver. In hca_cap_bits older fields are kept along with newer
fields that should have replaced them.
Fixes: c02b3741eb ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are systems platform information management interfaces (such as
HOST2BMC) for which we cannot disable local loopback multicast traffic.
Separate disable_local_lb_mc and disable_local_lb_uc capability bits so
driver will not disable multicast loopback traffic if not supported.
(It is expected that Firmware will not set disable_local_lb_mc if
HOST2BMC is running for example.)
Function mlx5_nic_vport_update_local_lb will do best effort to
disable/enable UC/MC loopback traffic and return success only in case it
succeeded to changed all allowed by Firmware.
Adapt mlx5_ib and mlx5e to support the new cap bits.
Fixes: 2c43c5a036 ("net/mlx5e: Enable local loopback in loopback selftest")
Fixes: c85023e153 ("IB/mlx5: Add raw ethernet local loopback support")
Fixes: bded747bb4 ("net/mlx5: Add raw ethernet local loopback firmware command")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add hairpin definitions to the IFC file.
This includes the HCA ID, few HCA hairpin capabilities, new
fields in RQ/SQ used later for the pairing and the WQ hairpin
data size attribute.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When mlx5_ib_add is called determine if the mlx5 core device being
added is capable of dual port RoCE operation. If it is, determine
whether it is a master device or a slave device using the
num_vhca_ports and affiliate_nic_vport_criteria capabilities.
If the device is a slave, attempt to find a master device to affiliate it
with. Devices that can be affiliated will share a system image guid. If
none are found place it on a list of unaffiliated ports. If a master is
found bind the port to it by configuring the port affiliation in the NIC
vport context.
Similarly when mlx5_ib_remove is called determine the port type. If it's
a slave port, unaffiliate it from the master device, otherwise just
remove it from the unaffiliated port list.
The IB device is registered as a multiport device, even if a 2nd port is
not available for affiliation. When the 2nd port is affiliated later the
GID cache must be refreshed in order to get the default GIDs for the 2nd
port in the cache. Export roce_rescan_device to provide a mechanism to
refresh the cache after a new port is bound.
In a multiport configuration all IB object (QP, MR, PD, etc) related
commands should flow through the master mlx5_core_dev, other commands
must be sent to the slave port mlx5_core_mdev, an interface is provide
to get the correct mdev for non IB object commands.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Generate a unique 128bit identifier for each host and pass that value to
firmware in the INIT_HCA command if it reports the sw_owner_id
capability. Each device bound to the mlx5_core driver will have the same
software owner ID.
In subsequent patches mlx5_core devices will be bound via a new VPort
command so that they can operate together under a single InfiniBand
device. Only devices that have the same software owner ID can be bound,
to prevent traffic intended for one host arriving at another.
The INIT_HCA command length was expanded by 128 bits. The command
length is provided as an input FW commands. Older FW does not have a
problem receiving this command in the new longer form.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In mlx5_ifc, struct size was not complete, and thus driver was sending
garbage after the last defined field. Fixed it by adding reserved field
to complete the struct size.
In addition, rename all set_rate_limit to set_pp_rate_limit to be
compliant with the Firmware <-> Driver definition.
Fixes: 7486216b3a ("{net,IB}/mlx5: mlx5_ifc updates")
Fixes: 1466cc5b23 ("net/mlx5: Rate limit tables support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma
-----BEGIN PGP SIGNATURE-----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=A1oL
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a fairly plain pull request. Lots of driver updates across the
stack, a huge number of static analysis cleanups including a close to
50 patch series from Bart Van Assche, and a number of new features
inside the stack such as general CQ moderation support.
Nothing really stands out, but there might be a few conflicts as you
take things in. In particular, the cleanups touched some of the same
lines as the new timer_setup changes.
Everything in this pull request has been through 0day and at least two
days of linux-next (since Stephen doesn't necessarily flag new
errors/warnings until day2). A few more items (about 30 patches) from
Intel and Mellanox showed up on the list on Tuesday. I've excluded
those from this pull request, and I'm sure some of them qualify as
fixes suitable to send any time, but I still have to review them
fully. If they contain mostly fixes and little or no new development,
then I will probably send them through by the end of the week just to
get them out of the way.
There was a break in my acceptance of patches which coincides with the
computer problems I had, and then when I got things mostly back under
control I had a backlog of patches to process, which I did mostly last
Friday and Monday. So there is a larger number of patches processed in
that timeframe than I was striving for.
Summary:
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (296 commits)
RDMA/core: Rename kernel modify_cq to better describe its usage
IB/mlx5: Add CQ moderation capability to query_device
IB/mlx4: Add CQ moderation capability to query_device
IB/uverbs: Add CQ moderation capability to query_device
IB/mlx5: Exposing modify CQ callback to uverbs layer
IB/mlx4: Exposing modify CQ callback to uverbs layer
IB/uverbs: Allow CQ moderation with modify CQ
iw_cxgb4: atomically flush the qp
iw_cxgb4: only call the cq comp_handler when the cq is armed
iw_cxgb4: Fix possible circular dependency locking warning
RDMA/bnxt_re: report vlan_id and sl in qp1 recv completion
IB/core: Only maintain real QPs in the security lists
IB/ocrdma_hw: remove unnecessary code in ocrdma_mbx_dealloc_lkey
RDMA/core: Make function rdma_copy_addr return void
RDMA/vmw_pvrdma: Add shared receive queue support
RDMA/core: avoid uninitialized variable warning in create_udata
RDMA/bnxt_re: synchronize poll_cq and req_notify_cq verbs
RDMA/bnxt_re: Flush CQ notification Work Queue before destroying QP
RDMA/bnxt_re: Set QP state in case of response completion errors
RDMA/bnxt_re: Add memory barriers when processing CQ/EQ entries
...
The QPTS register allows changing the priority trust state between pcp and
dscp. Add support to get/set trust state from device. When the port is
in pcp/dscp trust state, packet is routed by hardware to matching priority
based on its pcp/dscp value respectively.
The QPDPM register allow channing the dscp to priority mapping. Add support
to get/set dscp to priority mapping from device.
Note that to change a dscp mapping, the "e" bit of this dscp structure
must be set in the QPDPM firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The QCAM register provides capability bit for all the QoS registers
using ACCESS_REG command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch updates the mlx5_ifc with the following:
- Fix tunnel_stateless_gre typo.
- max_geneve_opt_len - Maximum geneve options length.
- tunnel_stateless_geneve_rx - If set, receive Stateless
Offloads for Geneve tunneled (inner) packets are supported.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Adding new bits in mlx5_ifc_cmd_hca_cap to get the hardware capabilities
for:
- compression_128: Support 128B CQE compression
- cqe_128_always: Support 128B CQE padding
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow creation of a multi-packet receive queue.
In order to create a multi-packet RQ, the following fields in
the mlx5_ib_rwq should be set:
- log_num_strides: Log of number of strides per WQE
- single_stride_log_num_of_bytes: Log of a single stride size
- two_byte_shift_en: When enabled, hardware pads 2 bytes of zeros
before writing the message to memory (e.g. for the IP alignment).
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Added check for the maximal number of flow counters attached
to rule (FTE).
Fixes: bd5251dbf1 ('net/mlx5_core: Introduce flow steering destination of type counter')
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
- Lots of hfi1 driver updates (mixed with a few qib and core updates as
well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so we
can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@
-----BEGIN PGP SIGNATURE-----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=2ntC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
Add TX offloads support for GRE tunneled packets by reporting the needed
netdev features.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Expose enhanced multi packet WQE capability to user space through
query_device by uhw.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the field to allow posting multi packet send WQEs if hardware
supports this feature. This doesn't mean the send WQEs will be for
multi packet unless the send WQE was prepared according to multi
packet send WQE format.
User space shall use flag MLX5_IB_ALLOW_MPW to check if hardware
supports MPW and allows MPW in SQ context.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set underlay QPN as part of flow rule when it's applicable.
There is one root flow table in the NIC RX namespace and all the
underlay QPs steer the traffic to this flow table.
In order to prevent QP to get traffic which is not target to its
underlay QP, we need to set the underlay QP number as part of
the steering matching.
Note:
When multicast traffic is sent the QPN filtering is done by the firmware
as some early step. Adding the QPN match on the flow table entry is
wrong as by that time the target QPN holds the multicast address (e.g.
FF(s)) and it won't match.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add outbound_pci_buffer_overflow to ethtool output for monitoring the
number of packets that were dropped due to lack of PCIe buffers on
receive path from NIC port toward the host(s).
This counter is valid only in case that tx_overflow_buffer_pkt is
supported in MCAM enhanced features.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add capability bit in PCAM register and counters to PPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add capability bit in MCAM register and counters to MPCNT register.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Read new NIC capability field which represnts 16 MSBs of the max flow
counters number supported (max_flow_counter_31_16).
Backward compatibility with older firmware is preserved, the modified
driver reads max_flow_counter_31_16 as 0 from the older firmware and
uses up to 64K counters.
Changed flow counter id from 16 bits to 32 bits. Backward compatibility
with older firmware is preserved as we kept the 16 LSBs of the counter
id in place and added 16 MSBs from reserved field.
Changed the background bulk reading of flow counters to work in chunks
of at most 32K counters, to make sure we don't attempt to allocate very
large buffers.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The counter list hardware structure doesn't contain a clear and
num_of_counters fields, remove them.
These wrong fields were never used by the driver hence no other driver
changes.
Fixes: a351a1b03b ("net/mlx5: Introduce bulk reading of flow counters")
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to mark relevant fields while setting the MTPPS register
add field select. Otherwise it can cause a misconfiguration in
firmware.
Fixes: ee7f12205a ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds below requester and responder side error counters,
which will be exposed by hardware counters interface and are supported
as part of query Q counters command extension.
+---------------------------+-------------------------------------+
| Name | Description |
|---------------------------+-------------------------------------|
|resp_local_length_error | Number of times responder detected |
| | local length errors |
|---------------------------+-------------------------------------|
|resp_cqe_error | Number of CQEs completed with error |
| | at responder |
|---------------------------+-------------------------------------|
|req_cqe_error | Number of CQEs completed with error |
| | at requester |
|---------------------------+-------------------------------------|
|req_remote_invalid_request | Number of times requester detected |
| | remote invalid request error |
|---------------------------+-------------------------------------|
|req_remote_access_error | Number of times requester detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_remote_access_error | Number of times responder detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at responder |
|---------------------------+-------------------------------------|
|req_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at requester |
+---------------------------+-------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RQs that were configured for "delay drop" will prevent packet drops
when their WQEs are depleted.
Marking an RQ to be drop-less is done by setting delay_drop_en in RQ
context using CREATE_RQ command.
Since this feature is globally activated/deactivated by using the
SET_DELAY_DROP command on all the marked RQs, we activated/deactivated
it according to the number of RQs with 'delay_drop' enabled.
When timeout is expired, then the feature is deactivated. Therefore
the driver handles the delay drop timeout event and reactivate it.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When delay drop timeout is expired, the firmware raises
general notification event of DELAY_DROP_TIMEOUT subtype.
In addition the feature is disable so the driver have to
reactivate the timeout.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support to SET_DELAY_DROP command.
This command will be used in downstream patches for delay packet drop.
The timeout value should be indicated by delay_drop_timeout field.
Packet processing will be delayed till timeout value passed or until
more WQEs are posted.
Setting this value to 0 disables the feature.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds debug control parameters for congestion control which
can be read or written through debugfs. They are for reaction point and
notification point nodes.
These control parameters are as below:
+------------------------------+-----------------------------------------+
| Name | Description |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate | When set target rate is updated to |
| | current rate |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate_ati | When set update target rate based on |
| | timer as well |
|------------------------------+-----------------------------------------|
|rp_time_reset | time between rate increase if no |
| | CNP is received unit in usec |
|------------------------------+-----------------------------------------|
|rp_byte_reset | Number of bytes between rate inease if |
| | no CNP is received |
|------------------------------+-----------------------------------------|
|rp_threshold | Threshold for reaction point rate |
| | control |
|------------------------------+-----------------------------------------|
|rp_ai_rate | Rate for target rate, unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_hai_rate | Rate for hyper increase state |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_min_dec_fac | Minimum factor by which the current |
| | transmit rate can be changed when |
| | processing a CNP, unit is percerntage |
|------------------------------+-----------------------------------------|
|rp_min_rate | Minimum value for rate limit, |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_rate_to_set_on_first_cnp | Rate that is set when first CNP is |
| | received, unit is Mbps |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_g | Used to calculate alpha |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_rtt | Time between updates of alpha value, |
| | unit is usec |
|------------------------------+-----------------------------------------|
|rp_rate_reduce_monitor_period | Minimum time between consecutive rate |
| | reductions |
|------------------------------+-----------------------------------------|
|rp_initial_alpha_value | Initial value of alpha |
|------------------------------+-----------------------------------------|
|rp_gd | When CNP is received, flow rate is |
| | reduced based on gd, rp_gd is given as |
| | log2(rp_gd) |
|------------------------------+-----------------------------------------|
|np_cnp_dscp | dscp code point for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio_mode | 802.1p priority for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio | cnp priority mode |
+------------------------------+-----------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support for raw ethernet local loopback firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add Innova IPSec ESP crypto offload configuration paths.
Detect Innova IPSec device and set the NETIF_F_HW_ESP flag.
Configure Security Associations using the API introduced in a previous
patch.
Add Software-parser hardware descriptor layout
Software-Parser (swp) is a hardware feature in ConnectX which allows the
host software to specify protocol header offsets in the TX path, thus
overriding the hardware parser.
This is useful for protocols that the ASIC may not be able to parse on
its own.
Note that due to inline metadata, XDP is not supported in Innova IPSec.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.
A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.
Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.
At high level, the FPGA configuration space is divided such:
0x00000000 - 0x007fffff is reserved for the SBU
0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ... is DDR memory
A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The FPGA QP is a high-bandwidth communication channel between the host
CPU and the FPGA device. It allows performing DMA operations between
host memory and the FPGA logic via the ConnectX chip.
Add ConnectX FW commands which create and manipulate FPGA QPs.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The offending commit pushed fwd the field by two bits but
didn't increment the offset, fix that. Currently, no damage
was done b/c this is just a field name, but lets have it right.
Fixes: f32f5bd2eb ('net/mlx5: Configure cache line size for start and end padding')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enhance MCAM to allow the driver to query which access regs are
supported. For now, expose the regs needed for FW flashing.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MCC (Management Component Control) allows to control a firmware
component update.
MCDA (Management Component Data Access) allows to read and write
a firmware component.
MCQI (Management Component Query Information) allows to query
information about firmware components.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For environments where flow-based ipv6 router is offloaded.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Enable offloading of TC matching on ip ttl / hop-limit
As matching on ttl is supported only by newer HW brands (ConnectX-5),
we should do capability check before attempting to offload that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Yevgeny Kliteynik
Maor Gottlieb
Eli Britstein
Ariel Levkovich
Saeed Mahameed
Aya Levin
Bodong Wang
Moni Shoua
Linus Torvalds
Yishai Hadas
Jason Gunthorpe
David S. Miller
Leon Romanovsky
Shahar Klein
Vu Pham
Eyal Davidovich
Oz Shlomo
Danit Goldberg
Gal Pressman
Shay Agroskin
Paul Blakey
Yonatan Cohen
Feras Daoud
Mark Bloch
Eran Ben Elisha
Denis Drozdov
Gal Pressman
Jianbo Liu
Or Gerlitz
Talat Batheesh
Ilan Tayari
Chris Mi
Huy Nguyen
Roi Dayan
Ilya Lesokhin
Tariq Toukan
Majd Dibbiny
Moshe Shemesh
Inbar Karmy
Boris Pismenny
Aviad Yehezkel
Daniel Jurgens
Guy Levi
Noa Osherovich
Raed Salem
Artemy Kovalyov
Rabie Loulou
Eugenia Emantayev
Parav Pandit