Currently, setting only legacy bitrates on 2.4GHz band
are supported. Mode 802.11b/g/bg is enabled based on
bitrates selection. If only CCK bitrates selected then
802.11b mode is enabled. If only OFDM bitrates are
selected then 802.11g mode is enabled. For both: CCK
and OFDM rates 802.11bg mixed mode is enabled.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using ieee80211_stop_queue, check the configured tx queue
limit before calling ieee80211_get_buffered_bc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While 32 KHz sleep clock might provide some power saving benefits,
it is also a major source of stability issues, on OpenWrt it produced
some reproducible data bus errors on register accesses on several
different MIPS platforms.
All the Atheros drivers that I can find do not enable this feature,
so it makes sense to leave it disabled in ath5k as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enabling the sleep clock alters the AR5K_USEC_32 field, but disabling
it didn't restore it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During scans the full calibration usually does not make much sense,
PAPD probing and IQ calibration should be deferred until there is
enough time to complete them. Adding 100 ms to the initial full
calibration delay should be enough to do this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a division by zero when setting distance before activating the
device for the first time.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Might fix some stability issues on newer chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfgain probe is only necessary for OFDM operation on AR5111 and AR5112.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Decryping frames on key_miss handling shouldn't be done for Michael
MIC failed frames as h/w would have already decrypted such frames
successfully anyway.
Also leaving CRC and PHY error(where the frame is going to be dropped
anyway), we are left to prcoess Decrypt error for which s/w decrypt is
selected anway and so having key_miss as a separate check doesn't serve
anything. So making key_miss handling mutually exlusive with other RX
status handling makes much more sense.
This patch addresses an issue with STA not reporting MIC failure events
resulting in STA being disconnected immediately.
Cc: stable@kernel.org
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple quoted strings are concatenated without comma separators.
Make the array const while there.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple quoted strings are concatenated without comma separators.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the compile warning cause by [IWL_TM_ATTR_MAX - 1]
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Belkin's Connect N150 Wireless USB Adapter, model F7D1101 version 2, uses ID 0x945b.
Chipset info: rt: 3390, rf: 000b, rev: 3213.
I have just bought one, which started to work perfectly after the ID was added through this patch.
Signed-off-by: Eduardo Bacchi Kienetz <eduardo@kienetz.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@kernel.org> [back to 2.6.39]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When commands time out, corruption ensues. As lbs_complete_command()
is called without locking, the command node is mistakenly freed twice.
Also fixed up locking here in a few other places.
The nature of command timeout may be that the card didn't even
acknowledge receipt of the request. Detect this case and reset dnld_sent
so that other commands don't hang forever.
When cmdnodes are moved between the free list and the pending list,
their list heads should be reinitialized. Fixed this.
Sometimes commands are completed without actually submitting them or
removing them from cmdpendingq. We must remember to remove them from
cmdpendingq in these cases, so handle this in lbs_complete_command().
Harmless signals generated during suspend/resume were interrupting
lbs_cmd. Convert to an uninterruptible sleep to avoid this.
lbs_thread must be woken up every time there is some new work to do.
I found that when 2 commands are queued, ther completion of the first
command would not wake up lbs_thread to submit the second. Poke lbs_thread
at the end of lbs_complete_command() to fix this.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't have multiple RX queues, so there's no use
in allocating multiple, use alloc_netdev_mqs() to
allocate multiple TX but only one RX queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I changed the TKIP key functions, but forgot to
update the documentation includes, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Looks like I forgot to document the "gfp" parameter
to cfg80211_gtk_rekey_notify, add it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SoCs like the bcm4716 do not have a sprom on the bcma bus like a
pcie device. It stores the values in some partition on flash memory.
For ssb this informations are read out in the bcm47xx arch code,
something like that should also be implemented for bcma. Without this
patch bcma panics on SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Problems located in the two functions lbs_set_reg() and lbs_get_reg():
- The offset field of struct cmd_ds_reg_access was not filled in
- The test on the return code of lbs_cmd_with_response() in function
lbs_get_reg() was inverted
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_AN_SYNTH9 is in the analog shift register range and thus needs to be
written using the ath9k_hw_analog_shift_rmw function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The radio needs twice / four times as much time to stabilize for half/quarter
channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the clock rate is initialized properly and SIFS, EIFS, USEC,
slot time and ACK timeout are properly calculated by the generic code,
the 'async FIFO' register hacks are no longer necessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize the the clock-to-TSF field of AR_USEC and the SIFS and EIFS time
registers based on the clock rate instead of relying on initvals.
With those changes, some of the hardcoded AR9287 1.3+ specific overrides
can be dropped.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This chip uses the async FIFO feature and runs the MAC at 117 MHz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling half/quarter rate makes the MAC run at half/quarter clock speed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All devices support this, but some disable it using an EEPROM flag
for some reason. Improves 5 GHz performance on those devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the proper masks for the register instead.
Fixes adding the (still unused) half/quarter PLL flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently device is not able to transmit in 40MHz in spite of
enabling 40MHz support in HTCapInfo IE in assoc req, because
11n specific FW capabilities for transmission are not initialized.
This patch adds code to initilize these capabilities.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not needed since the driver split. Move single use routines to
calling location and keep static where possible.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For testing purpose, we need better control of msc from user application.
Separate the fixed_rate between debugfs and testmode and enforce it.
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only host command allow to send to uCode is the one initiated from
testmode if testmode is the owner of uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we open the door to allow application control the device behavior through
testmode, add command to allow application request the ownership of the uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For all the hist command request from testmode, set the CMD_ON_DEMAND flag.
this flag will be used later to control the uCode behavior
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WiFi throughput drops drastically when BT is turned on, BT and WiFi
are simultaneously transmitting/receiving traffic. This is particularly true
when BT has higher priority over WiFi, and hence the device defers TX frames.
The AP assumes that the channel is bad and reduces the data rate, implying
longer airtime, which exacerbates the problem further, resulting ultimately
in what is popularly called the "death-spiral" phenomenon. The use of PS-poll
in such scenarios guarantees a low but consistent throughput.
Since the death-spiral phenomenon is observed only when the RSSI is low, use
PS-poll only when RSSI is low and disable when high, with a known hysterisis.
This feature specifies the high and low thresholds and implements the
callbacks registered with mac80211, which will be called when threshold events
occur.
iwlwifi: dynamic pspoll: optimize rssi monitor code
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 maintains a running average of the RSSI when a STA
is associated to an AP. Report threshold events to any driver
that has registered callbacks for getting RSSI measurements.
Implement callbacks in mac80211 so that driver can set thresholds.
Add callbacks in mac80211 which is invoked when an RSSI threshold
event occurs.
mac80211: add tracing to rssi_reports api and remove extraneous fn argument
mac80211: scale up rssi thresholds from driver by 16 before storing
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bt combo devices, need to use bt enabled handlers and functions
Reported-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to do double level indirect call after driver split
no functional changes
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not needed since the driver split. Eliminate redundant routine.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not needed since the driver split.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not needed since the driver split.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the for priv->trans.ops->...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar
Felix Fietkau
Senthil Balasubramanian
Joe Perches
Wey-Yi Guy
Mohammed Shafi Shajakhan
Eduardo Bacchi Kienetz
Larry Finger
Daniel Drake
Johannes Berg
Hauke Mehrtens
Olivier Sobrie
Pavel Roskin
Amitkumar Karwar
Don Fry
Meenakshi Venkataraman
Emmanuel Grumbach