Граф коммитов

164 Коммитов

Автор SHA1 Сообщение Дата
Roel Kluin 6f17c65240 regulator: wm831x_reg_read() failure unnoticed in wm831x_aldo_get_mode()
ret should be signed to notice a failure in wm831x_reg_read().

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:30 +00:00
Juha Keski-Saari cf9836f4dd twl-regulator: Fix reg_disable functionality for 4030 and 6030
This change makes sure all regulator group assignments are cleared on
disable call

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:29 +00:00
Juha Keski-Saari 53b8a9d92a twl-regulator: Add turnon delay to reg_enable
This change implements a basic turnon delay in the regulator enable function
to make it less probable that reg_enable returns before the regulator
output is at target level

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:29 +00:00
Juha Keski-Saari 30010fa52c twl-regulator: Restore REMAP configuration in regulator probe
This change ensures the regulator REMAP register configuration is in a known
state so state transitions will function as intended regardless of
possible bootloader effects on it

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:29 +00:00
Juha Keski-Saari 045f972f2c twl-regulator: Add turnon-delay and REMAP config to twlreg_info struct
This change includes regulator turnon delay values and the REMAP reset
configuration to the twlreg_info struct, since they are basic attributes
of every TWL regulator

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:29 +00:00
Juha Keski-Saari 205e5cd3d9 twl-regulator: Define critical regulators as always_on
Defines VIO, VDD1, VDD2, VPLL1 and VINT* regulators as always_on by default
since they are critical to TWL and its master's functionality and should
be on in all cases where RegFW is used

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:28 +00:00
Juha Keski-Saari 07fc493f03 twl-regulator: Add all twl4030 regulators to twlreg_info
Define all twl4030 regulators in the twlreg_info table, along with
appropriate VSEL tables for adjustable regulators

Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:28 +00:00
Alberto Panizzo 735eb93ae2 regulator: mc13783-regulator: correct the probing time.
When the mc13783-regulator driver is built in kernel, probing it during
the regulator subsystem initialisation result in a fault.

That is because regulator subsystem is planned to be initialised very early
in the boot process, before the mfd subsystem initialisation.

The mc12783-regulator probing process need to access to the mc13783-core
functionality to read/write mc13783 registers and so must be called after
the mc13783-core driver initialisation.

The way to do this is to let the kernel probe the mc13783-regulator driver when
mc13783-core register his regulator subdevice.

Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:28 +00:00
Lars-Peter Clausen eb143ac1b9 regulator: Fix unbalanced disables/enables in regulator_bulk_{enable,disable} error path
Currently it is possible for regulator_bulk_{enable,disable} operations to
generate unbalanced regulator_{disable,enable} calls in its error path.
In case of an error only those regulators of the bulk operation which actually
had been enabled/disabled should get their original state restored.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:28 +00:00
Stefan Roese fa2984d469 regulator: core.c: Small coding style cleanup (indentation fixup)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:27 +00:00
Julia Lawall d662fc82dc drivers/regulator: use PTR_ERR to get error code
IS_ERR returns only 1 or 0.  The callsite of setup_regulators expects a
negative integer in an error case.  Thus, PTR_ERR has to be used to extract
it.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression E,E1;
@@

*E = IS_ERR(...)
 ... when != E = E1
*return E;
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:27 +00:00
Uwe Kleine-König a10099bc88 regulator/mc13783: various cleanups
- define needed registers and bits in the driver
- properly namespace functions and structs
- fix locking as required by patch
  "mfd/mc13783: near complete rewrite"
- use platform_data as provided by "mfd/mc13783: near complete rewrite"
  instead of accessing struct mc13783
- struct mc13783_regulator_priv.desc is (and was) unused and so can go
  away
- use cpp magic to initialize mc13783_regulators
- bring MODULE_LICENSE in sync with actual copyright
- minor style fixes

This allows not including mc13783-private.h which I intend to remove
soon.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:26 +00:00
Uwe Kleine-König b4b90c659d regulator/mc13783: rename source file to match other drivers
One annoying thing about the old name was that the module was just
called mc13783 which caused wrong expectations (at least for me).

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:26 +00:00
Linus Walleij 176f45b9c9 Fix some AB3100 regulator issues
This patch will remove surplus register writes on shut down of
LDO D (this magic was not needed), remove an unnecessary (!) error
check and really unregister the regulators when the module is
unloaded.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:25 +00:00
Roel Kluin 495353a3f7 regulator: keep index within bounds in da9034_get_ldo12_voltage()
If selector equals ARRAY_SIZE(da9034_ldo12_data), that is one too
large already.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:25 +00:00
Mark Brown ddec68107a regulator: Ensure val is initialised in 88pm8607 choose_voltage()
If we fall through it means that we hit an unknown regulator/chip
combination so set -ENOENT as an explicit flag (the return code
is only used internally).

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:25 +00:00
Mark Brown 9992ef40ff regulator: Remove duplicate consts from ab3100
'static const int const' means the same thing as 'static const int'
and sparse complains about this.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:25 +00:00
Mark Brown 638f85c54f regulator: Handle regulators without suspend mode configuration
Since some regulators in the system may not support suspend mode
configuration we need to allow some regulators to have a missing
suspend mode configuration. Do this by requiring that disabled
regulators are explicitly flagged and then skip over regulators
that have no state specified.

Try to avoid surprises by warning the if we could set the state
but no configuration is provided.  This also ensures that an all
zeros configuration generates a warning rather than silently
disabling the regulator.

Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:25 +00:00
Mark Brown 1083c39346 regulator: Factor out regulator name pretty printing
Some of the regulator API functions have code to allow the machine
constraints to override the device supplied name for the regulator
in the constraints in order to help tie logging to supplies on the
board and disambiguate when there is more than one regulator chip
in the system. Factor this code out into a new rdev_get_name()
function and use it throughout the regulator API so that we always
use the same name.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:24 +00:00
Mark Brown 8f031b48cd regulator: Display actual settings with constraints
When voltage or current constraints are either missing or specify
a range display the actual setting along with the constraints if
we can. This can aid debugging of configuration problems.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:24 +00:00
Mark Brown af5866c9cd regulator: Also lift apply_uV into machine_constraints_voltage()
It makes sense to do all the voltage configuration in the one split
out function.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:24 +00:00
Mark Brown e79055d62e regulator: Factor out voltage constraint setup
This allows constraints to take effect on regulators that support
voltage setting but for which the board does not specify a voltage
range (for example, because it is fixed correctly at system startup).

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:23 +00:00
Mark Brown 5b30762773 regulator: Report error codes for bulk operations
If we're going to log an error we may as well log what the error
code that we're failing on is.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:23 +00:00
Haojian Zhuang be0e2d3e80 regulator: add 88PM8607 PMIC driver
Hi Liam,

Since Samuel merged a new version of mfd 88pm8607 driver, I format a
new patch on regulator 88pm8607. I paste the new patch in mail. Please
help to review again. And I also attach the mfd driver in mail.

From: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Thu, 8 Oct 2009 09:36:53 -0400
Subject: [PATCH] regulator: Add 88PM8607 PMIC driver

This patch adds regulator drivers for Marvell 88PM8607 PMIC.
This controller contains 3 DVC and 14 LDO regulators. This controller
uses I2C interface.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:23 +00:00
Mark Brown e24a04c44c regulator: Implement WM831x BuckWise DC-DC convertor DVS support
The BuckWise DC-DC convertors in WM831x devices support switching to
a second output voltage using the logic level on one of the device
pins. This is intended to allow rapid voltage switching for uses like
cpufreq, replacing the I2C or SPI write used to configure the voltage
of the regulator with a much faster GPIO status change.

This is implemented by keeping the DVS voltage configured as the
maximum voltage permitted for the regulator. If a request is made
for the maximum voltage then the GPIO is used to switch to the DVS
voltage, otherwise the normal ON voltage is updated and used. This
follows the idiom used by most cpufreq drivers, which drop the
minimum voltage as the core frequency is dropped but use a constant
maximum - raising the voltage should normally be fast, but lowering
it may be slower.

Configuration of the DVS MFP on the device should be done externally,
for example via OTP.

Support is present in the hardware for monitoring the status of the
transition using a second GPIO. This is not currently implemented
but platform data is provided for it - the driver currently assumes
that the device will be configured to transition immediately - but
platform data is provided to reduce merge issues once it is.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:22 +00:00
Wolfram Sang 27f37e4bfe regulator: add driver for MAX8660/8661
Tested with a MX25-based custom board.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-17 10:27:22 +00:00
Rajendra Nayak 441a450554 regulator: Add support for twl6030 regulators
This patch updates the regulator driver to add support
for TWL6030 PMIC specific LDO regulators.
SMPS resources are not yet supported for TWL6030 and
also .set_mode and .get_status for LDO's are yet to
be implemented for TWL6030.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-14 00:26:20 +01:00
Rajendra Nayak c4aa6f3143 mfd: Rename twl4030_ routines in twl-regulator.c
This patch renames all twl4030_ functions to twl so that regulator driver
can be reused by Triton - TWL4030 and Phoenix - TWL6030.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 21:36:49 +01:00
Balaji T K fc7b92fca4 mfd: Rename all twl4030_i2c*
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 21:23:33 +01:00
Santosh Shilimkar b07682b605 mfd: Rename twl4030* driver files to enable re-use
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.

This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 20:05:51 +01:00
Mark Brown 6a6127462e mfd: Mask and unmask wm8350 IRQs on request and free
Bring the WM8350 IRQ API more in line with the generic IRQ API by
masking and unmasking interrupts as they are requested and freed.
This is mostly just a case of deleting the mask and unmask calls
from the individual drivers.

The RTC driver is changed to mask the periodic IRQ after requesting
it rather than only unmasking the alarm IRQ. If the periodic IRQ
fires in the period where it is reqested then there will be a
spurious notification but there should be no serious consequences
from this.

The CODEC drive is changed to explicitly disable headphone jack
detection prior to requesting the IRQs. This will avoid the IRQ
firing with no jack set up.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 19:21:40 +01:00
Mark Brown 5a65edbc12 mfd: Convert wm8350 IRQ handlers to irq_handler_t
This is done as simple code transformation, the semantics of the
IRQ API provided by the core are are still very different to those
of genirq (mainly with regard to masking).

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 19:21:39 +01:00
Lars-Peter Clausen 98c2e49030 mfd: Fix pcf50633-regulator drvdata usage
Currently the pcf50633-regulator driver data is set to the pcf50633 core
structure, but the pcf50633-regulator remove handler assumes that it is set to
the regulator device. This patch fixes the issue by accessing the pcf506533
core structure through its parent device and setting the driver data to the
regulator device.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2009-12-13 19:21:20 +01:00
Mark Brown e8092da92e regulator: Initialise wm831x structure pointor for ISINK driver
The version that made it into mainline missed the initialisation of the
chip handle.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-12-02 19:37:16 +00:00
Dan Carpenter 80099c707e dereferencing freed memory regulator_fixed_voltage_remove()
Don't dereference drvdata after it has been freed.

regards,
dan carpenter

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-11-16 12:40:25 +00:00
Roel Kluin 9a767d43fb regulator: Fix check of unsigned return value and transmit errors in wm831x_gp_ldo_get_mode()
If ret is unsigned, the checks for negative wm831x_reg_read() return values
are wrong. The error value should be transmitted to its caller, e.g.
wm831x_gp_ldo_get_status() which tests for a negative return value.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-11-16 09:57:17 +00:00
Mark Brown 60ef66fcf4 regulator: Handle missing constraints in _regulator_disable()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-11-16 09:57:16 +00:00
Haojian Zhuang 55c1d7c60d regulator: fix voltage range in da9034 ldo12
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:58:23 +01:00
Wolfram Sang 12a1d933a9 regulator/lp3971: drop unnecessary initialization
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:45 +01:00
Wolfram Sang a954c487b9 regulator: drop 'default n'
Specifying 'default n' is superfluous.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:44 +01:00
Roel Kluin 656d0498ea regulator: fix calculation of voltage range in da9034_set_ldo12_voltage()
For val to be greater than 7 or less than 20 is logically always true.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:44 +01:00
Michael Prokop 6f2653e63a drivers/regulator/Kconfig: fix typo (s/Usersapce/Userspace/) in REGULATOR_USERSPACE_CONSUMER description
Signed-off-by: Michael Prokop <mika@grml.org>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:43 +01:00
Linus Walleij a7433cff9e REGULATOR Handle positive returncode from enable
This makes _regulator_enable() properly handle the case where
a regulator is already on when you try to enable it. Currently
it will erroneously handle positive return values as an error.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:43 +01:00
Liam Girdwood 9e108d33ed regulator: tps650xx - build fixes for x86_64
Fixes the following errors on both tps650xx regulator drivers :-

drivers/regulator/tps65023-regulator: struct i2c_device_id is 32 bytes.  The last of 1 is:
0x74 0x70 0x73 0x36 0x35 0x30 0x32 0x33 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
FATAL: drivers/regulator/tps65023-regulator: struct i2c_device_id is not terminated with a NULL entry!

This patch also fixes the GPL v2 licence string for both drivers.

Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:43 +01:00
Anuj Aggarwal 2de798506d Regulator: Adding TPS65023 and TPS6507x in Kconfig and Makefile
Adding TPS65023 and TPS6507x regulator driver support in
drivers/regulator/Makefile and drivers/regulator/Kconfig

Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:42 +01:00
Anuj Aggarwal 3fa5b8e082 Regulator: Add TPS6507x regulator driver
Adding support for TI TPS6507x regulator driver

Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:42 +01:00
Anuj Aggarwal 30e6599d31 Regulator: Add TPS65023 regulator driver
Adding support for TI TPS65023 regulator driver

Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:42 +01:00
Felipe Balbi e9d62698e8 regulator: userspace: use sysfs_create_group
and avoid introducing our own loops for creating
several sysfs entries.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:41 +01:00
Roger Quadros 86d9884b6a regulator: Add GPIO enable control to fixed voltage regulator driver
Now fixed regulators that have their enable pin connected to a GPIO line
can use the fixed regulator driver for regulator enable/disable control.
The GPIO number and polarity information is passed through platform data.
GPIO enable control is achieved using gpiolib.

Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Reviewed-by: Philipp Zabel <philipp.zabel@gmail.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:41 +01:00
Lars-Peter Clausen a6576cff18 Regulator: Implement list_voltage for pcf50633 regulator driver.
This patch implements list_voltage for the pcf50644 regulator driver.
As the voltages are linearly scaled the code to convert register values to
voltages can be reused and most of the code can be shared with get_voltage.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-09-22 13:32:41 +01:00